Mohawk HGO45-50 Installation Guide

Mohawk HGO45-50 Installation Guide
Locking Engineered Hardwood Flooring with Uniclic Technology
Float and Direct Glue Installation Instructions
Engineered Hardwood Glueless Locking Flooring can be installed over most properly prepared subfloors and are engineered to
be dimensionally stable, making them suitable for installation over all grade levels where moisture conditions do not exist. See all
information and installation guidelines below or contact Technical Services at 888-387-9881, Option 3
A Caution: Wood Dust
Cutting, sanding or machining wood products produces wood dust While wood
products are not hazardous under the OSHA Hazard Communication Standard
(29 CFR 1910.1200), the International Agency for Research on Cancer (IARC) and
the State of California have classified wood dust as a human carcinogen.
PROPOSITION 65 WARNING: This product produces wood dust when cut,
sanded or machined. Wood dust is considered a carcinogen by the State of
California.
Precautionary Measures: Airbome wood dust can cause respiratory, skin and eye
irritation. Power tools should be equipped with a dust collector. Use an appropriate
NIOSH-designated dust mask. Avoid dust contact with skin and eyes.
First Aid Measures in case of irritations: In case of irmtation flush eyes with water. If
WARNING! DO NOT MECHANICALLY CHIP OR PULVERIZE EXISTING RESILIENT
FLOORING, BACKING, LINING FELT, ASPHALTIC "CUTBACK" ADHESIVES OR
OTHER ADHESIVES.
Previously installed лезет? floor covering products and the asphaltic or cutback
adhesives used to install them may contain either asbestos fibers andfor crystalline
silica. The products in this carton DO NOT contain asbestos or crystalline silica.
Avoid creating dust. Inhalation of asbestos or crystalline dust is a cancer and respiratory
tract hazard. Smoking by individuals exposed to asbestos fibers greatly increases the
risk of serious bodily harm. Unless positively certain that the product is a non-asbestos
containing material, you must presume it contains asbestos. Regulations may require
that the matenal be tested to determine asbestos content and may govern the removal
and disposal of material. See current edition of the Resilient Floor Covering Institute
(RFC) publication “Recommended Work Practices for Removal of Resilient Floor
Coverings” for detailed information and instructions on removing all resilient covering
structures.
needed seek medical attention. If dermatitis occurs, seek medical attention.
INSTALLER / OWNER RESPONSIBILITY:
It is the responsibility of the installer and owner fo ensure that job site environmental,
subfloor and subsurface conditions involved meet or exceed all requirements as
outlined in installation instructions prior to installation. Manufacturer declines all
responsibility for product performance or installation failure due to sub-floor, substrate
or environmental deficiencies or jobsite conditions.
All work involving water or moisture (plumbing, masonry, painting, plastering) must be
completed prior to flooring being delivered. Building envelope must be complete and
exterior doors and windows installed. Exterior grading and gutter downspouts should
be completed and permanent HVAC systems in operation for 14 days prior fo flooring
being delivered to job site. Measures should be taken to protect floors from other trade
work. Do not cover floors with plastic, red rosin, felt or wax paper or previously
used cardboard. Instead use a breathable material such as clean, dry, plain
uncoated cardboard or Kraft paper. Inks from printed cardboard could damage
the hardwood floor. The floor should be thoroughly cleaned before covering to
remove grit and debris that would damage the finish. The floor must be completely
covered to eliminate uneven ambering from exposure to UV light.
Manufacturer requires Engineered Hardwood products with Glueless Locking
technology acclimate for 48 hours prior to installation. Acclimation allows flooring to
achieve equilibrium moisture content (EMC) with the installation environment. All wood
continually expands and contracts until it reaches moisture equilibrium with the
environment in which it's installed. As with all wood flooring, expansion and contraction
will be minimized if climate control is consistently maintained year round. This is
especially important with tropical species, because denser woods experience
more significant shrinkage in low moisture / low humidity environments.
Room temperature should be 60 - 80° F, with relative humidity between 35 -55%.
These environmental conditions are specified as pre-installation requirements
and must be maintained for the life of the product.
Building interiors are affected by two distinct humidity seasons — Heating and Non-
Heating. Care should be taken to maintain humidity levels between 35-55%.
Manufacturer warranties do not cover natural expansion and contraction which
results in separation between planks, or damage caused by excessively low or
high humidity.
Heating season — Low Humidity, Dry. All heating methods create dry, low humidity
conditions. Humidifiers are recommended to prevent excessive shrinkage or gapping
in wood floors due to seasonal periods of low humidity.
Non Heating Season and Coastal or Waterfront Areas - High Humidity, Wet
During the non heating season proper humidity levels should be maintained by using
an air conditioner, dehumidifier or by turning on your heating system periodically
during the summer months.
Do not install in full bathrooms or powder rooms.
Examine flooring for color, finish and quality prior to installation. If material is
unacceptable, contact the seller immediately. Wood is a natural product and contains
characteristics such as variations in color, tone and graining. Flooring is manufactured
in accordance with industry standards, which allows manufacturing and natural defect
tolerances up to 5% of the total installation. Installer should work from several cartons
at the same time to ensure good color and shade blend. Installer should not install
undesirable pieces.
Flooring warranties DO NOT cover materials with visible defects once they are
installed. Installer and Owner are responsible for final inspection of flooring
manufacture, grade and finish. Purchase an additional 5% of flooring to allow for cuts
and an additional 10% if installing diagonally.
WARRANTY NOTE: Installer should provide owner with one carton end label
from product installed for warranty purposes. Owner should retain carton end
label and copy of invoice for their records. Excess flooring should be retained and
stored in a climate controlled area for future repairs in the event planks are damaged.
The use of stain, filler or putty for correction is considered a normal practice and a
routine part of installation.
TOOLS:
BASIC TOOLS AND ACCESSORIES:
Broom Terry Cloth Towels
Coordinating transition strips or molding Mineral Spirits
Coordinating stain, filler or putty Hand or Electric Jam Saw
Chalk line Power Circular Saw or Miter Saw
Thick felt or rubber pads Wood/Concrete Moisture Meter or Both
Uniclic Tapping Block Safety Glasses
¥2 Inch Wood Spacers Straight Edge
Table Saw Tape Measure
Carpenters Square Pry Bar or Trim Puller
Utility Knife Pencil
Moisture Resistant Foam Underlayment Pull Bar
Mohawk FloorCare Essentials Hardwood and Laminate Floor Cleaner
For Floating Installation: Use Performance Accessories Underlayments or products
that meet or exceed these products’ specifications. The use of accessories other
than Performance Accessories might cause damage to the Glueless Locking
G Clic 10/10
Hardwood Flooring. Therefore, we recommend products specifically designed
and tested for use with Engineered Hardwood Glueless Locking Flooring.
For Direct Glue Installation: Use Mohawk's Protack M908 Urethane Adhesive with
the recommended trowel for adhesive application. For Moisture Membrane
Application; Use Mohawk's Protech M301 Moisture Membrane, with a 5/32" x 3/16" М
Notch Trowel for moisture retarder membrane application or products that meet or
exceed manufacturers adhesive and sealer specifications. When installing on
concrete subfloors, trowels should be replaced every 3000 ft. Never use a water based
adhesive to install Engineered Glueless Locking Hardwood Flooring.
STORAGE AND HANDLING:
Flooring should be delivered and stored at the jobsite for 48 hours prior to installation
fo allow the product to acclimate from prior transport or storage conditions. Flooring
should be stored with at least a four inch air space under cartons. Do not open cartons
but remove any plastic wrap that may have been used to ship the material. This is
especially important if you live in a very humid or dry climate.
PRE-INSTALLATION & JOB SITE CONDITIONS
SUBFLOOR REQUIREMENTS:
The following subfloor recommendations are intended to complement the
installation of hardwood flooring as an interior finish. Hardwood flooring is not
a structural component. These recommendations are not intended to supersede
federal, state or local building codes, but as with many other interior finish
products, may require modifying existing structural components for a
successful installation.
SUBFLOOR PREPARATION RECOMMENDATIONS FOR ALL
INSTALLATIONS:
Glueless Engineered Floors may be installed over any structurally sound subfloor that
is flat, clean and dry on all grade levels. Do not install in full bathrooms or powder
rooms.
All subfloors should be:
* CLEAN — Subfloor must be clean and free of dirt, curing compounds, drywall mud,
wax, paint, oil, sealers, adhesives and other debris. These may be removed
mechanically.
* FLAT — Within 3/16" in 10" radius (5 mm in 3 m) and/or 1/8" in 6' radius (3 mm in 2
m). Sand high areas or joints. Fill low areas with a high compressive strength (min.
3,000 psi) Portland base compound.
* DRY — Select the appropriate moisture indicator test specifically designed for use
with wood or concrete subfloors. Test and record moisture content results.
« STRUCTURALLY SOUND — Nail or screw any areas that are loose or squeak. Wood
panels should exhibit an adequate fastening pattern, glued/screwed or nailed as that
system requires, using an acceptable nailing pattern. Typical: 6” (15 cm) along bearing
edges and 12” (31 cm) along intermediate supports. Flatten edge swell as necessary.
Replace any water-damaged, swollen or delaminated subflooring or underlayment.
Building codes establish requirements for structural support components of flooring
systems which may not provide adequate rigidity and support for proper installation
and performance of a hardwood floor. Whenever possible, install flooring
perpendicular to the floor joists for maximum stability.
NOTE: Avoid subfloors with excessive vertical movement or deflection because
subfloor movement will telegraph through to the finished installation. Indications of
excessive deflection are uneven finish wear, fastener release, squeaking,
compromised or damaged locking systems, sectional contours such as bowing or
dipping in floors and uneven flooring material. Nail or screw subfloor panels to secure
boards with excessive vertical movement or deflection. If the subfloor has excessive
vertical movement (deflection) before installation of the flooring, it is likely it will do so
after installation of the flooring is complete. Our warranties DO NOT cover any
problems caused by inadequate substructures or improper installation of said
substructures.
Subfloor moisture check
Note: To increase reliability, moisture testing should be performed after the HVAC
system has been in operation for a minimum of 14 days. Excess moisture on any
flooring substrate if not identified and corrected prior to installation will cause floor
covering failure. Warranties DO NOT cover products installed over improperly
prepared subfloors, substrates or environmental related deficiencies.
Acceptable conditions for above, on and below grade applications are:
Concrete Subfloor Moisture Content
On and below grade applications are susceptible to moisture and should be tested for
moisture prior to installation in several locations within the installation area. Acceptable
conditions for above, on and below grade applications on concrete are:
. Less than 3 Ibs. /1000 sq. ft_/24 hrs. Calcium Chloride Test (ASTM F1869)
or
. Less than 75% RH Levels in Concrete Using In-situ Probes (ASTM F 2170-02)
Or
. No greater than 5% on a Tramex Concrete Moisture Encounter meter or
equivalent concrete moisture meter.
DO NOT INSTALL FLOORING IF MOISTURE TESTS RESULTS EXCEED
RECOMMENDED LIMITS.
NOTE:
New concrete slabs require a minimum of 60 days drying time before covering them
with a wood floor. (Must be fully cured) Although initial moisture tests may indicate a
dry slab, the moisture content of slabs may increase due to seasonal fluctuation or
weather patterns. New construction should have a minimum 10 mil poly membrane
between the ground and concrete.
Wood Subfloor Moisture Content
Test both wood subfloor and wood flooring for moisture content using a reliable pin
type moisture meter. The subfloor material must not exceed 12% moisture content.
The difference between the moisture content of the wood subfloor and the hardwood
flooring must not exceed 4%.
If subfloor moisture readings exceed recommended levels for concrete or wood, steps
MUST be taken to reduce subfloor moisture. Steps could include waiting for subfloors
to dry to acceptable levels or using an appropriate moisture barrier such as Mohawk’s
Protech M901 Moisture Membrane.
NOTE: Basements and crawl spaces must be dry. Use of a 6 mil black polyethylene
membrane is required to cover 100% of the crawl space earth. Crawl space clearance
from ground to underside of joist should be no less than 18” and perimeter vent
spacing should be equal to 1.5% of the total square footage of the crawl space area to
provide cross ventilation.
To correct any subfloor conditions concerning moisture, either wait until the
subfloor dries to meet specifications or use an appropriate moisture barrier. For
more information concerning moisture conditions, contact Technical Service
Department at 888-387-9881 Option 3.
Concrete Subfloor
Lightweight concrete
To test for lightweight or acoustical concrete, scrape a coin or key across the surface
of the subfloor. If the surface powders easily or has a dry density of 100 pounds or less
per cubic foot, Glueless Locking flooring should be installed as floating only.
Wood Subfloors
NOTE: As with many other interior finish products, modification of existing
structural components may be required for a successful installation.
Solid Wood Subfloors - Direct Glue or Floating Installations
* Minimum 3/4" (19 mm) thick with a maximum width of 6" (15 cm) installed at a 45°
angle to the floor joists.
* Group 1 dense softwood (Pine, Larch, Douglas fir, etc.) No. 2 common, kiln dried
with all board ends bearing on joists.
* For glue-down applications add 3/8" (9.5 mm) approved floor panel underlayment.
G Clic 10/10
Existing Wood Flooring - Direct Glue or Floating Installations
e Existing engineered flooring must be well bonded/fastened. When gluing over
existing wood flooring, the surface finish must be abraded or removed to allow
adequate adhesive bond.
e Bxisting solid hardwood flooring that exceeds 6° (15 mm) in width must be covered
with 3/8" (9.5 mm) approved underlayment and fastened as required. Do not
install over solid flooring attached directly to the concrete.
Wood subfloors should be well nailed or secured with screws. Nails should be ring
shank and screws need to be counter sunk. The wood subfloor needs to be
structurally sound (meaning subfloors without loose boards, vinyl or tile).
If sub-floor panels are a single layer, less than 34’ thick, add another single cross layer
for strength and stability (minimum 3/8” thick for a total 1 1/8" thickness).
Underlayment floor panels must be installed sealed side down. When used as a
subfloor, allow 1/8" (3 mm) expansion space between each panel. If spacing is
inadequate, cut in with a circular saw. Do not cut in expansion space on tongue and
groove panels.
When installing parallel to the floor joists it may be necessary to increase rigidity of the
structural subfloor system by installing an additional minimum of 3/8" (9.5 mm)
approved underlayment floor panel.
Approved underlayment floor panels should meet or exceed the following:
es Plywood: Must be minimum CDX grade {exposure 1) and meet US Voluntary
Product Standard PS1 performance standard or Canadian performance standard
CANICSA 0325-0-92. The preferred thickness is 3/4" (19 mm) as a subfloor
[minimum 5/8" (16 mm)] or 3/8" (9.5 mm) as floor panel underlayment.
e Oriented Strand Board (0SB): Conforming to US Voluntary Product Standard
PS2 or Canadian performance standard CAN/CSA 0325-0-92 construction
sheathing. Check underside of panel for codes. When used as a subfloor, the
panels must be tongue and groove and installed sealed side down. Minimum
thickness to be 23/32" (18 mm) thick when used as a subfloor or 3/8" (9.5 mm) as
floor panel underlayment.
« Wafer board and Chipboard: Conforming to US Voluntary Product Standard PS2
or Canadian performance standard CAN/CSA 0325-092. Must be 3/4" (19 mm)
thick when used as a subfloor and 3/8" (9.5 mm) thick when used as floor panel
underlayment.
e Particleboard: Must be a minimum 40-b. density, stamped underlayment grade
and 3/4" (19 mm) thick. (Floating installation only)
Mohawks ProTack Adhesive is the recommended wood flooring adhesive and may be
used for above, on, and below grade applications and on all common substrates
except particleboard and sheet vinyl.
Sub-floors other than wood or concrete:
Note: Penmeter glued resilient vinyl and rubber tiles are unacceptable underlayments
and must be removed.
Terrazzo, Vinyl, Resilient Tile, Cork and Linoleum or hard surfaces that are dry,
structurally sound and level are suitable as a sub-floor. As above, the surface must be
sound, tight and free of paint, oil, existing adhesives, wax, grease and dirt. Terrazzo
and ceramic tile must be scuffed to assure adhesion.
Warning! Do not sand existing resilient tile, sheet flooring, backing, or felt linings.
These products may contain asbestos fibers that are not readily identifiable. Inhalation
of asbestos dust can cause asbestosis or other serious bodily harm. Check with local,
state and federal laws for handling hazardous material before attempting the removal
of these floors.
Direct Glue Installation: Make sure the floor covering materials are well bonded to
the subfloorfunderlayment with full spread adhesive and no more than two layers thick,
not to exceed 3/16" (5 mm).
With approved wood/wood composite subfloors, if vinyl or tiles are loose, broken, or in
poor condition, install a 3/8" (9.5 mm) approved underlayment directly over the flooring
materials.
Clean the flooring materials as necessary to remove waxes, sealers or cleaning
residues to allow a good adhesive bond.
Cork floor sealers and surface treatments must be removed.
Always check for adequate adhesive bond prior to beginning direct glue installation.
Radiant Heat Subfloors
It is important to follow these guidelines strictly. Failure to follow these
guidelines may produce unsatisfactory results.
Only floating installations are approved for radiant heat systems. Direct glue
down is NOT RECOMMENDED.
Before installing hardwood over radiant heat subfloors, determine if the radiant heat
system is rated to be compatible with hardwood flooring. It is highly recommended the
radiant heat system be designed specifically to accept hardwood flooring. Radiant
heat systems designed for floor coverings with a higher resistance to heat
transfer such as carpet will damage wood flooring. Single heat circuit systems
designed for use with multiple floor covering products must be adjusted to work at
temperatures suitable for hardwood flooring. Use of an in floor temperature sensor
as well as a separate thermostat for the individual room is required. An outdoor
temperature sensor should be used to adjust water temperature according to
anticipated heat loss.
Note: When radiant heat is installed in concrete, mortar beds, or gypsum cement, it is
very important to operate the radiant heat system until these are completely dry before
you install your hardwood flooring on top. This may take several weeks. Also operate
the HVAC system to allow humidity levels in the area to stabilize (35-55% RH) for the
area in which the hardwood floor will be installed. Allow hardwood to acclimate to this
humidity level before installation. This will minimize dimensional changes due to
moisture.
Before installing over a radiant heat floor turn off heat and wait until the floor has
reached room temperature (70°-75°F). After installing the floor, gradually retum the
heat in 5 degree increments. CAUTION: The floor surface must never exceed 85°F.
Before You Start
* Plan your layout and determine the direction of the installation in the room. Planks
installed parallel to windows accent the
hardwood best.
+ Blending of Cartons: To achieve a uniform
installation appearance, preselect and set
aside hardwood planks that blend best with all
trims and moldings. Install these planks next
to best blended moldings.
+ Remove all wall mounted moldings such as
base and quarter round.
+ Floor should be installed blending planks from
several cartons at the same time to ensure good color and shade mixture throughout
the installation.
+ Be attentive to staggering the ends of the boards at least 4"-6"1 (10-15 cm) when
possible, in adjacent rows.
+ The floating floor underlayment already has double-sided tape for ease of taping the
precut overlapping seams. If a non-adhesive underlayment is used, tape all seams.
* Do not install in areas of high moisture such as bathrooms and powder rooms.
NOTE: DO NOT USE A RUBBER MALLET TO INSTALL FLOORING. STRIKING
THE SURFACE WITH A RUBBER MALLET MAY "BURN" THE FINISH CAUSING
IRREPARABLE DAMAGE.
PREPARATION:
Undercut Door Casings: Undercut all door casings 1/16” higher than the thickness of
the flooring materials being installed. To do this, use a scrap piece of flooring as a
guide. Lay it on the substrate and cut the casing with a handsaw or use a power jamb
saw set at the correct height. Remove all moldings and wall-base, and undercut all
door casings.
G Clic 1010
FLOATING INSTALLATION
Underlayment:
Use Performance Accessory Underlayments or equivalent underayment with equal
or better specifications. Underlayment requirements are very critical to a floating
installation. Excessive pad compression or compaction is a common cause of seam
failure.
Lay the underlayment on the floor with the moisture barrier facing up. The direction of
the underlayment should be parallel to the direction of the floor. For the first row of
flooring the underlayment should be placed so that approximately 1 inch overlaps onto
all perpendicular walls. Place the following row next to the first row on top of the lower
moisture barrier overlap. Remove the adhesive strip and fold back the upper overlap
on the second row. Make sure the underlayment fits together tightly (don't leave gaps).
On the last row, place the underlayment 1 inch up the wall. To join rolls on the short
side of the underlayment, use a moisture resistant tape to connect the 2 pieces so
water cannot penetrate the underlayment.
Expansion Space:
An expansion space of at least 1% inch must be maintained around the perimeter of the
room, all pipes, counters, cabinets, fireplace hearths, doorframes and any other fixed
vertical objects in the room. Doorway or archways 4 feet or less and rooms larger
than a 26 X 33 are required to have a T-Molding.
Getting Started:
Starting Off - The First Three Rows
Row One:
Plank 1 should begin in the left hand corner of the room. Spacing around the wall
perimeter of 12° can be maintained by using wood wedges. The planks are laid with
the tongue side facing the wall, which enables you fo best work with the Uniclic
system. The first row starts with a full length board; working from left to right will be
required when installing glueless engineered hardwood flooring. Slide the end groove
of the board being installed into the end tongue of the board you previously installed.
Place each plank firmly against the wood wedges. After setting the first row and
making sure you are against a firm starting point, lay out three to four rows before
starting to install.
(Figure 3) Plank 2 end tongue is connected to the end groove of Plank 1. Lay the rest,
plank after plank, in this manner until you have completed the first row. Cut the last
plank accordingly. Please ensure that this first row is straight using the wedges to
maintain proper 12"expansion space from the wall.
FIGURE 3
Row Two:
When possible use leftover plank from the first row to begin the second row. The
leftover piece from the first row should be considered for this starter piece to minimize
waste. Initial layout of material will allow you to check your end seams to ensure they
are not too close. End joints on adjoining rows should be offset by no less than 6”.
Align this plank and lock the side into place against the first plank in row 1. The next
plank is aligned with the end joint first into the previously plank in row 2. The side of
plank is then tapped lightly against the previously laid row. Continue laying in this way
across the entire row. Remove the fitting wedge and press in the row of planks with a
light pressure on the long side. The planks lock into each other. The Uniclic Tapping
Block square edge tapping block is needed to aid in the connection of the locking
system on the long side. The planks are now laid row after row in this sequence.
Row Three and Remaining Rows:
Move rows if necessary to ensure that you are not showing any undesirable joint
patterns. (Figure 2A) The rest of the row's end joints should be random throughout the
floor. (Figure 1A) Your first three rows are staggered ensuring that offset of previous
row with end joints are no closer than 6° from one another. When the planks are being
tapped in place, a non-random pyramid or stair step pattern is used to ensure the
planks remain engaged through the force of the tapping. The numbered process is
shown in Figure 3.
==
Figure 2A Figure 1A
Most often walls are not structurally square. Planks in the first row may need to be
scribed and cut to contour the first row with the wall and to allow for 12” expansion.
Allow 12" expansion space at all vertical obstructions. Use 12° wood wedges or short
cut =" pieces of the floor against the wall to hold planks true to spacing. It is important
that the planks follow the wall. Scribing is used if the wall is not straight. First, mark the
plank with a scribing tool or other tool that will allow you to follow the shape of the wall
and then cut it lengthwise fo follow the line.
(Figure 2)
las...
FIGURE 2
NOTE: Another way to achieve a firm starting point is to screw down a straight
length of 1"x3" lumber, or another straight, firm material along the full length
of the starter wall. This is set to the outside edge the distance of the width of
your end planks plus the 12"expansion. You will be removing this after the rest
of the floor is installed and the space filled and ripped to size the flooring.
The Uniclic Tapping Block square edge tapping block is needed to distribute equal
force across the tongue without any damage. (Figure 4 and Figure 5)) For best results,
slide the tapping block along the sub floor and row, tapping lightly with a hammer,
using tapping strokes to engage the locking system. If the planks are not going
together, check to see if the planks are moving against the wall with the strikes. If so,
adjust shims to firm up or use the screw down starter row method.
FIGURE 4
Force is evenly
distributed
through the Impact of
tapping block hammer at
one point,
to the tongue
of the floor.
G Clic 10/10
FIGU
=,
E
RES FIGURE 8
GLUE DOWN INSTALLATION
Tapping the planks together GUIDELIN ES
When tapping the planks together the following process works best: 1) Using the
Uniclic Tapping Block, lightly tap each piece for the first 3-4 rows. After the first 3-4 ; я :
a : Sh : q q
rows, you should only need the Uniclic Tapping Block every third row. Start tapping in NITE: IF Sue: down Nena heidwood Toon
the plank at the opposite end along the length working from left to right, making sure only urethane adhesives may be used.
the plank fully engages as you progress down the length. (Figure 4)
If an excess subfloor moisture situation exists it is
2) When end joint is slid into place on the preceding plank, raise the plank now being
installed to an approximate 45° angle while setting the side joint into place. (Figure 6)
3) When you have the plank in place, lower the plank while pushing in until plank locks
in place. The planks should lock into place at this point. (Figure 7)
Your initial rows, if you are not against a firm starting structure, it may seem more
difficult to engage than the preceding rows.
required that Mohawk's Protech M901 Moisture
Membrane be applied before installing with Mohawk's ProTack M3908 Urethane
Adhesive.
Use of these or products with equal or greater specifications are necessary for
warranty compliance.
FIGURE 6
If subfloor moisture is below recommended levels, simply follow direct glue
installation instructions below.
INSTALLING PROTECH M901 MEMBRANE:
ProTech M901 Moisture Membrane: A trowel-applied membrane that improves
the long-term performance of glue-down wood-flooring installations over concrete
substrates.
TYPICAL TROWEL AND APPROXIMATE COVERAGE"
0/32" x 316" 40 to 45 sg. ft. U.S. gal.
* Coverage may vary depending on substrate conditions.
USES
* For protection from concrete moisture (up to 25 Ibs. MVER)
» For reducing sound transfer in multi-story buildings
+ For improving flexibility and increasing bond strength of installations
Note: Do not apply over self-stick tile, sheet vinyl, old adhesives, metal, linoleum,
laminate, particleboard or strip wood subfloors. Air temperature must be between 50°F
and 100°F for applying ProTech M901 Moisture Membrane.
FIGURE 7 APPLICATION
май | 1. Regulate temperature and humidity 72 hours before, during and after installation.
2. Complete undercuts before applying Protech M301. Include the additional 1/16”
height of Protech M901 when calculating undercuts.
. Pour ProTech M301 onto substrate (no mixing necessary).
Using the notched side of a 5/32" x 3/16" V-notched trowel, spread Protech M901
evenly. Product will flatten out naturally.
. Allow to dry completely (12 to 16 hours).
. Correct any missed spots and voids with trowel's flat side.
. Allow repair areas to dry completely.
- While membrane is fresh, clean tools using a urethane adhesive cleaner or mineral
spirits. Protech M901 is extremely difficult to remove when cured.
9. Install glue-down wood flooring using Mohawk Protack M908 Urethane Adhesive.
NOTES
* Product must be used in its entirety when opened. Lid cannot be re-sealed.
* Temperature and humidity will affect the curing time. The higher the temperature and
humidity, the faster the cure.
da Lad
o E En
G Clic 10/10
Getting Started Direct Glue:
GENERAL INFORMATION FOR GLUE-DOWN APPLICATIONS
1. Use cement based patch, skim coat leveling products to correct substrate
imperfections.
2. Regulate temperature and humidity 72 hours before, during and after installation.
3. At least 48 hours before installation, place wood flooring in the installation area.
4 Install and secure starter row.
5. Spread adhesive using recommended trowel, ensuring 95 fo 100% adhesive
contact. Wet lay method: press flooring firmly into adhesive immediately after
troweling.
6. Inspect the installation and remove any adhesive smudges or drops immediately.
NOTE: Urethane adhesive is very difficult to remove once dry and cured. Make every
effort to prevent adhesive from getting on the flooring surface. For best results, keep a
urethane adhesive cleaner nearby to remove any adhesive smudges or drops during
installation.
f. Clean tools while adhesive is fresh using a urethane adhesive cleaner or mineral
spirits.
8. Avoid light/regular fraffic for at least 12 hours. Avoid heavy traffic for at least 24
hours.
9. See adhesive manufacturer guidelines for OPEN TIME on the adhesive container.
10. Proper ventilation within the room must be provided. An electric fan is helpful.
Step 1
Select a starter wall. It is recommended to w=
start the installation along an exterior wall. ; +5 Y
Its more likely to be straight and square { E ”
with the room. Measure out from the wall - \! Za
the width of two planks and mark each end = “up en
| — (1
of the room and snap your chalk line. AY 7
step?
Spread Mohawk's Pro-Tack M908 Adhesive from the chalk line to the starter wall using
the recommended trowel size. It is important to use the correct trowel at a 45 to get
the proper spread of adhesive applied to the sub-floor, which will produce a proper and
permanent bond. Improper bonding can cause loose or hollow spots.
Note: Change the trowel every 2000 fo 3000 square feet due to wear down of the
notches. This assures you always get the proper spread of adhesive.
Step 3
Install the first row of starter planks with the tongue facing the starter wall and secure
into position. Alignment is critical and can be achieved by securing a straight edge
along the chalk line (2x4’s work well), or by top nailing the first row with finishing nails
(wood subfloor), or adjustable spacers (concrete sub-floor). This prevents slippage of
the planks that can cause misalignment.
Note: The planks along the wall may have to be scribed and cut to fit in order to
maintain a consistent expansion space since most walls are not straight Try to
maintain at least 2” on the scribed plank.
Step 4
Once the starter rows are secure spread 2 2 to 3 feet of adhesive the length of the
room. (Never lay more adhesive than can be covered in approximately 2 hrs.) Place
tongue into groove of plank or strips and press firmly into adhesive. Never slide planks
or strips through adhesive. Use Uniclic
Tapping Block to fit planks snug together at << `` ~
side and butt ends. Clean any adhesive off the CR E
surface before it cures using clean terry cloth NES mo NS
towels and mineral spirits. СА
—
т <, ®
i X x = SA i =-
a
"a
Note: Never work on top of the flooring when installing. If you must work on top of the
newly laid flooring use a kneeling board.
Secure your starter rows with a straight edge (2x4's). Once the remainder of the floor
has been installed go back to the beginning and remove the straight edges and spread
adhesive on the remainder of the open subfloor. Remember planks closest to the wall
may have to be scribed and cut to fit due to irregulanties along the wall. When using
Mohawks Pro-Tack M308 adhesive it is not necessary to roll the floor.
Final Touches
Install the proper trim molding at the doorways to achieve the transition and along the
walls to cover the edges of any gaps along the wall due to irregularity.
Complete the job by using the wood filler that coordinates with the installed engineered
flooring for minor corrections or areas where brad nails were used in the trim or the
flooring. Clean the finished floor with Mohawks FloorCare Essentials Hardwood &
Laminate Cleaner.
Trim excess underlayment (floating installation only) and install or re-install any
transition pieces, reducer strips, T-moldings, thresholds, bases and/or quarter round
moldings. Trims and moldings should be nailed into the wall, not the floor.
To prevent surface damage, avoid rolling heavy furniture and appliances on the floor.
Use plywood, hardboard or appliance lifts if necessary. Use protective castors/castor
cups or felt pads on the legs of furniture to prevent damage to the flooring.
Clean Up
Use clean white terry cloth towels to clean as you go along with mineral spirits. It is
easy and convenient to use. Adhesive that has cured on the surface of the flooring can
be difficult to remove. Measures should be taken fo protect floors from other trade
work. If the floor is to be covered, the floor should be thoroughly cleaned prior to
covering to prevent grit damage to the finish. Do not cover with plastic, red
rosin, felt or wax paper or previously used cardboard. Instead use a breathable
material such as clean, dry, plain uncoated cardboard or Kraft paper. Inks from
printed cardboard could damage the hardwood floor. A common reinforced
builder's paper is a good choice. Any covering should be taped, using a low-adhesion
tape, to base or shoe moldings. Avoid taping to finished flooring. When taping paper
or sheets together, tape them to each other, not to the floor. The floor must be
completely covered to eliminate uneven ambering from exposure to UV light.
MAINTENANCE
Engineered Glueless Hardwood Floors are very easily maintained. No wax, no mess.
Simply use Mohawk's FloorCare Essentials Hardwood & Laminate Floor Cleaner and
a terry cloth flooring mop.
STEP ONE: Sweep your floor to remove any particles that could scratch your floor.
Warning: Vacuums with a beater bar or power rotary brush head can damage a wood
floor and should never be used.
STEP TWO: Apply the approved Mohawk FloorCare Essentials Hardwood & Laminate
Flooring Cleaner directly to the terry cloth flooring mop, not to the floor!
STEP THREE: Use a back and forth motion with the mop. When the terry cloth cover
becomes soiled, simply replace it with a clean one. Cleaning the floor with a soiled
cover could cause streaking. The covers are re-usable so simply throw the cover in the
wash and dry it as you would any towel. DO NOT USE FABRIC SOFTENER when
washing terry cloth covers.
Tips & Warnings:
Sweep regularly, with a soft bristle broom.
Remove spills promptly and use Mohawk's FloorCare Essentials
Hardwood & Laminate Floor Cleaner and a clean white cloth.
Use felt protectors under heavy pieces of furniture and chairs.
Use protective mats at all exterior entrances. Do not use mats or area rug
cushions constructed of rubber or PVC. Instead use urethane backed
products.
= Spiked heels or shoes in need of repair can severely damage your floor.
G Clic 10/10
. Replace hard plastic, metal casters or wheels on furniture with soft rubber
casters or by using a protective mat under the casters.
. Never wet or damp mop your wood floors. Water can cause damage to
wood flooring.
. Never use oil soaps, wax, liquid or other household products to clean your
floor.
The sun's UV rays can change the color of your floor.
Keep animal nails trimmed.
Protect your floor when using a dolly for moving furniture or appliances.
Never slide or roll heavy furniture or appliances across the floor.
. Never use steam cleaners on your wood floors. This will force moisture
into the wood and cause damage to your flooring.
. Use protective window coverings to protect hardwood floors from
excessive heat during penods of direct sunlight.
Exterior and interior walk off mats should be used at all exterior entrances fo avoid
exposure fo moisture from tracking during periods of inclement weather. Walk off mats
should be routinely maintained to avoid becoming a soil source. Do not use mats or
under mat cushions constructed of rubber or PVC. Instead use urethane backed
products.
Hardwoods react to sunlight
Hardwood contains certain types of acids in their cellular structure. With exposure to
sunlight these acids begin to amber. The color change is referred to as patina. The
wood will reach its own natural warmth and patina level and stop ambering. The
amount of patina is directly related to the species, amount of acids and the level of
sunlight. The enfire floor will reach the same patina level over time. This is often
noticed after a rug is removed and the floor is noticeably different in color underneath.
If you remove the rug and expose the entire floor to the same amount of light, it will
even out over time and become uniform in color.
Hardwood flooring will scratch and dent
With today’s active lifestyles it is important to note that hardwood flooring can, and will,
scratch and dent. See Tips & Warnings for protecting your hardwood floor. In order to
prevent excessive abuse the use of strategically placed mats and area rugs as well as
floor protectors on chair and table legs are a must.
WARRANTIES
A copy of the Warranty may be obtained by calling the Technical Service Department
at 888-387-9881 option 3.
Rev 10/10
G Clic 10/10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement