AYC Gratitude boat Operations Manual

GRATITUDE

OPERATIONS MANUAL

Welcome aboard!

We are happy you have chosen us for your vacation. We are sure you will enjoy cruising the wonderful islands of the Pacific Northwest.

We trust this manual will help you become familiar with the boat.

If you have questions about the boat or about places to visit, please do not hesitate to ask any of the AYC staff.

We wish to fair winds and following seas!

1

TABLE OF CONTENTS

Safety ................................................................................................................ 4

Quick Start ....................................................................................................... 5

Boat Operation ................................................................................................ 8

Engine Inspection ........................................................................................ 8

Start-Up ........................................................................................................ 11

Shutdown ..................................................................................................... 13

Before Leaving Dock ................................................................................... 14

Getting Underway ........................................................................................ 14

Cruising ........................................................................................................ 14

Docking ........................................................................................................ 15

Fueling ......................................................................................................... 15

Boat Electrical ................................................................................................. 17

A.C. System ................................................................................................. 19

Inverter ......................................................................................................... 21

D.C. System ................................................................................................. 22

Batteries ....................................................................................................... 22

Sanitation System

Marine Toilet ............................................................................................... 24

Holding Tank ............................................................................................... 24

Y-Valve ........................................................................................................ 26

Water Systems

Fresh Water Tanks ....................................................................................... 27

Fresh Water Pump ....................................................................................... 27

Hot Water ..................................................................................................... 27

Shower ......................................................................................................... 28

Washdown .................................................................................................... 28

Galley

Stove & Oven ............................................................................................... 29

Refrigerator .................................................................................................. 30

2

Heating Systems

Diesel Heater ................................................................................................ 31

Engine Heat .................................................................................................. 31

Bilge Pumps ..................................................................................................... 32

Electronics

VHF Radio ................................................................................................... 33

Depth Sounder ............................................................................................. 33

Radar ............................................................................................................ 34

GPS / Plotter ................................................................................................ 34

Entertainment

AM/FM Radio and each other ..................................................................... 35

Anchoring ........................................................................................................ 36

Mooring Buoys ................................................................................................ 38

Barbecue........................................................................................................... 39

Dinghy & Outboard ........................................................................................ 40

Crabbing & Fishing ........................................................................................ 42

Thru-Hulls ....................................................................................................... 43

3

SAFETY

Safety should be paramount in your daily cruising.

Lifejackets are located in forward and aft cabin closets and also on the fly bridge under the port (left) aft facing seat. A few should always be out and ready, in fact we recommend wearing them whenever working on the decks.

Flares are located under the salon settee in the left hand cupboard.

Fire extinguishers are located in the forward cabin, Salon, and aft cabin.

It is a good idea to discuss what to do in case of an unexpected person in the water... Man Overboard!

4

QUICK START

Before Starting Engines:



Dinghy secured? Grill covered?



Disconnect shore power, store cord



Power panel: double green dots ALWAYS ON; green dots ON for normal operation; yellow dots ON as needed; red dots ALWAYS OFF



Open curtains for visibility



Check WOBBS: water (engine coolant), oil, belts, bilges and strainers



Check engine pads for signs of leaks



Close aft stateroom door to cockpit to keep diesel fumes out of the cabin

Starting Engines:



Put gear controls in neutral, throttle levers at slightly above “idle”



On “Engine Panel” of the DC Panel, flip starboard power switch to ON for starboard engine. Buzzer will sound (low oil pressure warning)



Push STARTING button for the starboard engine. When engine starts, throttle back to a smooth idle. Buzzer should stop. Do not try to start more than 30 seconds without a 2-minute “rest” period



Repeat procedure for port engine



Warm up at idle RPM



Check oil pressure for both engines: 30-90 PSI



Check for water coming out of both engine exhausts at the stern

Before Leaving the Dock:



Center the rudder



Untie mooring lines



Initial piloting away from the dock can be done at idle using selective forward and reverse of the twin props



Make sure engines are at idle before shifting gears. Make a slight pause at neutral before shifting between forward and reverse

Underway:



Stow mooring lines and fenders



Keep watch for logs or debris in water



Monitor gauges



Keep engines RPM under 1300 until engines warm to 150 degrees



Normal RPM is between idle and 2200. Gratitude cruises a very comfortable 8 knots @

1600 RPM with fuel consumption about 3 gals per hour. Do not exceed 2300 RPM for more than 30 minutes – check engine temps!



Normal readings: Engine Temp 175-190 Oil Pressure 30-90 psi

5

Approaching Dock:



Put fenders out. We generally put fenders down on both sides when maneuvering in close quarters. Have extra fenders ready if the vessel will make contact with the dock or another boat



Attach bow line to cleat and run line out through the hawse hole, OUTSIDE the bow rail and OUTSIDE fender lines toward midship. Same procedure for stern and spring lines.

Station a member of the crew at midship to tend the mooring lines



Engine throttle should be dead slow and rudders centered. Close maneuvering is best done with forward and reverse maneuvers with twin props.



Mate ready to step off swim step (No leaping across water to dock!) and secure spring line (most circumstances), then bow and stern. Often you will find a friendly person to catch your dock lines and help you secure them.



Position mate on deck with a spare large fender with line attached.

Upon Arrival at Marina:



Secure all lines. Stern, bow and two spring lines at a minimum



If bow-in, be sure anchor is not protruding over dock walkway



Turn off engines (see “Stopping Engines” below)



Turn off electronics at both helm stations; replace covers



Connect shore power. First to the boat, then to the shore receptacle (30 amp power for

Gratitude)



If at an unfamiliar marina, be sure to check polarity of the shore power connection before turning on the breaker at the dock

Stopping the Engines:

After operating at cruising speed, allow engines to idle a few minutes to cool down before shutting them down (this usually happens naturally while tying dock lines or setting anchor).

You can also turn on the engine room VENTS to help cool the engine room.



On Engine Panel turn the far left STOP SOL breaker to the ON position



Push the port STOPPING button. Low oil pressure buzzer will sound



Turn off the port engine power breaker. Buzzer will stop



Push the starboard STOPPING button. Buzzer will sound



Turn off the starboard engine power breaker. Buzzer will stop



Turn OFF the STOP SOL breaker

Daily (Overnight) Checklist in Marina:



AC Input ON for shore power



Inverter ON – be sure it is charging



Keep an eye on the holding tank. The meter is located in the master stateroom head on the sink vanity

6

Daily (Overnight) Checklist at Anchor or Buoy



Anchor light ON during hours of darkness.



Turn off unnecessary electrical items. Even unplugging appliances not in use will help reduce the drain on battery power - turn off the power strip for the microwave and coffee maker



Keep an eye on the holding tank. The meter is located in the master stateroom head on the sink vanity

Mooring at Anchor:



All anchoring should be done with the engines running as the windlass uses a lot of power



Turn on WINDLASS POWER on panel to the right of the helm. Anchor is lowered with foot switches on bow deck below the Windlass. Lower the anchor while backing the boat slowly from anchorage



Mate on bow to monitor length of chain going out and to troubleshoot if it gets tangled.

Anchor line is marked as indicated in the Operations Manual



When desired chain length is out, stop Windlass



Attach snubber lines to anchor chain. Use of snubber lines will give a more comfortable anchorage as they act like springs to absorb tension on the line. Attach snubber lines to the anchor chain beyond the anchor roller in order to take the “load” off the Windlass.

Secure snubber lines through bow hawse holes and to bow cleats.



Run out enough chain to take the tension off the Windlass



Back the boat at idle using just one engine to test the set of the anchor. Use a combination of sighting objects in the harbor and GPS to confirm anchor set



Turn OFF Windlass power at the panel



STOP engines

First Thing Each Day:



If at anchor, turn OFF the anchor light



Check battery reserve on inverter panel. If less than 12 volts, consider starting engines to begin recharging house batteries before using any additional electricity



Check fresh water tank level



Check holding tank gauge. If near full, it will be necessary to pump out very soon

Before Leaving Vessel:



DC power panel: turn freshwater (F.W.) Pump OFF



Cover electronics screens at both helm stations



Close curtains



Lock the cabin doors



If you are docked at an island, make sure no food is left out or accessible as critters will come aboard

7

BOAT OPERATION

ENGINE INSPECTION

Remember WOBBS every morning: Water (Coolant), Oil, Belts, Bilge and

Strainer.

Access to the engine compartment is below the helm. There is a strap on the hatch to prevent it from slamming down on your head.

Water (Coolant):

This engine does not lend itself to an easy check of the level of Coolant in the coolant reservoir.

However, you can check the coolant level from the coolant overflow tanks mounted in front of each engine. Minimum coolant levels when engines are cool are marked on each bottle. The

Fleet Captain will have checked this prior to your arrival and normally it should not be necessary to check it during your trip.

However, if you notice overheating please open the coolant cap located towards the front of the engine once the engine has cooled down. The best method to check for coolant is to place one finger inside the reservoir. If your finger touches coolant at any point when inside the reservoir, the coolant level should be adequate.

8

Oil:

Port Engine Starboard Engine

Check the level of Oil in each engine by using dipsticks located on the side of each engine, easily accessed from the center of the boat.

Look at the etch marks on each dipstick that indicate the proper oil level.

Only add oil if level is near the lower mark and DO NOT OVERFILL! Please use a paper towel or oil rag, not the dish towels, to wipe off the dipstick. Ensure the dipsticks are fully seated back into the tube when done.

Belts:

Check the general condition and tightness of the belts. If they feel tight, that’s about right.

Bilge:

Check the lower areas of the engine room for excess water. You will note the amount when you first start and after that if it increases, check for causes.

There are sorbs (diapers) under each engine. They will help identify if there are leaks in the engine and to determine where they may be. Under normal operation there are minimal drips, however if an engine is dripping significantly check for the probable cause.

9

Strainer:

Ensure the valve (yellow handle) on each raw water thru-hull is in the “OPEN” position (lever in-line with valve).

Observe the metal screen through the glass of each strainer for debris. At times it may become necessary to clean the strainer due to a buildup of debris clogging the system. It is important to keep a close eye on sea strainer condition, and if they need a cleaning follow these simple directions:

1. Opposite the yellow handle on the base is a small T-handle. Loosen this about two turns, note that some water may leak through. Close the seacock,

(yellow valve).

2. Open the strainer cover using the spanner wrench located in the drawer on the portside of the helm.

3. Clean the strainer thoroughly.

4. Reassemble, remembering to reopen the seacock and tighten the T-handle once the strainer is completely put back together.

T-handle

Open

10

START-UP

The engines should be started from the lower helm station.

1. Turn battery selector to “2” – Start Batteries.

2. GEARSHIFT in neutral.

3. THROTTLE should be just above the idle position.

Normally, plan to start the STARBOARD engine first.

4. Make sure the STOP SOL switch is ON

5. Turn the STBD POWER switch ON. You should hear a loud buzzing noise, this is normal, it’s the low oil pressure alarm.

6. Press the STBD STARTING button. After a few seconds the buzzer should stop indicating the oil pressure is normal. If it does NOT stop, turn off the engine by holding the STOPPING button. Determine why the buzzer did not stop. If because of no oil pressure, see Note below.

7. Turn the PORT POWER switch ON and again note the buzzer.

8. Press the PORT STARTING button.

Battery Selector Engine Panel

Raise the engine speed to between 700-800 rpm on the TACHOMETER (or just enough to stop most of the vibration)

11

Instrument Panel

Check the engine exhausts at the stern. There should be water burping out of the exhausts. If there is no water coming out, shut down the engines and see NOTE below.

NOTE--If oil pressure is low, shut down the engine, and inspect engine compartment and look for possible cause (for example, loss of oil.)

Caution -- If an engine is overheating or there is lack of raw water expelled in the engine exhaust, stop the engine immediately. Recheck the raw water-cooling system to ensure the seacock on the strainer is open (handle in-line with valve).

Next, check the raw water strainer for debris. If necessary, close the seacock, remove the strainer, clean, re-assemble, and reopen the seacock. Restart the engine and re-check water flow from the exhaust. If water is not flowing properly, the

Raw Water Pump may need to be serviced. Call AYC.

12

SHUT-DOWN

After operating at cruising speed, allow engines to idle a few minutes to cool down before shutting them down (this usually happens naturally while tying dock lines or setting anchor). You can also turn on the engine room VENTS to help cool the engine room.

GEARSHIFT in neutral position.

THROTTLE in idle position.

Make sure the STOP SOL us UP, or ON.

Turn off engines by pressing the STOPPING button for each engine. Low oil pressure buzzer will sound.

Silence buzzer by turning the POWER switches

OFF.

Turn the STOP SOL breaker OFF.

13

BEFORE LEAVING DOCK

DISCONNECT the shore power cord and stow it aboard. When disconnecting from the dock, make sure to turn the POWER OFF at the dock breaker before you pull out the power cord. This will prevent a ‘short’ between the power cord legs.

Forward power connection Aft power connection

Close the portholes, windows, and forward hatch.

Set up VHF radio and electronics.

Brief crew on what you expect from them to depart, lines, fenders, etc. It’s also a good idea if they know what you are going to do!

GETTING UNDERWAY

All close quarters maneuvering should take place at the upper (flybridge) helm for better visibility.

Shift only at idle to avoid transmission damage.

Once outside the marina, stow fenders and lines.

CRUISING

Maximum cruising speed is about 1800 RPM. If you run at a slightly slower RPM

(1400) you will cruise at about 7 knots and use a little over 2 gallons per hour.

Speed will vary depending upon the weight, currents and weather conditions.

NOTE: -- Higher engine speed causes higher temperatures (and possible damage) as well as a substantial increase in fuel consumption.

14

DOCKING

During docking, use of the flybridge provides greater visibility of the stern (most damaged part of a boat).

Have the crew prepare the lines and fenders and give clear instructions on how you expect to dock (bow in, port side tie; etc.). Fenders at the rear of the boat are the most important, however be sure there are several on each side.

Before entering the marina center the wheel (rudders will then be straight) and use only the GEARSHIFTS to maneuver the boat. (Throttles and Steering may be necessary in very windy conditions).

FUELING

A deck fitting key is located in the step locker at the starboard side of the helm.

Before pumping, have an oil/fuel sorb handy to soak up spilled fuel. You should have a rough idea of the number of gallons you will need by the engine hour indicator and how hard you have been driving.

Make sure you have the correct fuel, DIESEL!

And, be sure it is going into the correct deck fill.

Please double-check as fuel

in a holding tank isn't safe!

15

Open the top and bottom sight gauge shutoffs at the port and starboard fuel tanks by turning them in-line with the sight gauges.

Sight gauge shutoffs (shown in closed position)

Sight gauges are a quick and accurate way of determining how full the diesel tanks are.

Place the DIESEL nozzle into the tank opening, pump slowly and evenly, and note the sound of the fuel flow. Pumping too fast may not allow enough time for air to escape, which may result in a fuel spill from the tank vent. As the tank fills, the sound will rise in pitch (like water filling up a glass).

As it nears full, monitor the sight gauges located in the engine room. Stop filling when the fuel level rises to the top of the sight gauge, this is considered full.

Pay attention to the overflow vent on the outside of the hull near the deck fitting.

Fill carefully and be prepared to catch spilled fuel. A fuel spill could result in a fine from law enforcement. By correctly using the sight gauges you should not have any problems.

Replace each deck fitting. It isn’t necessary for them to be extremely tight as there are rubber gaskets on the fitting preventing water from entering.

Turn OFF top and bottom sight gauge shutoffs at the port and starboard fuel tanks when finished.

16

ELECTRICAL

The electrical control panels are located on the starboard side of the helm. The electrical system is divided into two distribution systems: 12 Volt DC Panel (12 volt batteries) on top and 120 Volt AC (shore power and inverter) on the bottom.

Dot system on the DC panel –

Double green dots: Always ON; Green dots: ON during normal operation;

Yellow dots: ON as needed; Red dots: normally OFF

12 Volt DC Panel 120 Volt AC Panel

When not connected to shore power, the batteries are providing all power. Monitor the use of electricity carefully with the voltmeter on the Magnum Energy

Charger/Inverter located at eye level to the left of the lower helm.

When any battery is at 11.8V, or lower than 12V it is time to re-charge the batteries. If on a buoy or at anchor, you can do this by running the engines at

1200-1400 RPM for an hour or so on ALL batteries. Check the voltmeter to verify the increase in battery charge after shutting the engines down.

17

Inverter / Charger: Manages the charging of batteries, and the conversion of 12V to 120V power delivered to selected appliances and

120V outlets. In addition, the Magnum inverter can display individual battery voltage.

Turn off electrical devices that are not needed to conserve battery power when not running, or on shore power.

To manage batteries and ensure the boat will start:



Shore Power: Battery Selector should be ALL - All batteries will be charged; 120 Volt outlets and appliances up to 30 amps will work.



Boat Underway: Battery selector should be ALL - All batteries will be charged; 120 Volt outlets and appliances will only work if Inverter is on.



Boat at anchor or on mooring buoy: Battery selector should be on “1”

House Batteries. Also, it would be prudent to turn off the fridge, and other battery draining devices until morning. If in doubt, check the battery voltage on the Magnum Inverter / Charger to make sure voltage is sufficient.

SHORE POWER supports all AC equipment and receptacles on board, as well as the battery charger.

18

Forward power connection Aft power connection

To connect to shore power, plug the 30amp power cord into the boat (either shore power connection, forward or aft) and the dock receptacle. If necessary, 50 amp,

30 amp, 20 amp adapters are available.

At the AC POWER PANEL make sure the REVERSE POLARITY light is NOT on. Use the “PUSH TO CHECK” button before turning the master switch ON.

AC Power Panel

If it is on, do not turn on the SHORE CIRCUIT BREAKER, as there is a problem with the power supply. Almost all marinas in the San Juan Islands will not experience this problem; it is typically the outlying areas that could be a problem.

19

If the light is not “ON” then it is OK to turn on the SHORE POWER BREAKER and you should see approximately 120V on the AC meter. Then, turn on appropriate breakers for the battery charger, refrigeration, water heater, etc. Watch the ammeter to see corresponding load changes.

If the load is greater than the available power (30 amp, 20 amp, etc.), a breaker will likely trip at the dock power connection. If this occurs, reset the dock circuit breaker and turn on the boat systems one at a time while watching the load so as not to exceed the rated maximum 30 amps (3,000 watts), 20 amps (2,000 watts) or even 15 amps (1,500 watts) depending on shore power availability.

Amps = Watts / Volts

Here are some example AC loads:

Microwave

Hair dryer

1000 watts

1500 watts

8.3 amps

12.5 amps

Coffee maker

Water Heater

1000 watts

1500 watts

8.3 amps

12.5 amps

This means you could potentially trip the shore power circuit breaker using any three of these appliances simultaneously.

If a normal AC outlet does not work, check the GFIC on one or more of the available outlets in the fwd head, or above the microwave to make sure it has not tripped. Each GFIC outlet can power several other outlets.

20

INVERTER POWER

The Inverter control is located above and to the port side of the helm on the

Magnum Energy panel. This will provide AC power to the 110-volt receptacle plugs (i.e. the microwave oven, coffee maker) when the boat is disconnected from shore power and the inverter button is depressed. The inverter will not provide power to the water heater or battery charger. The label is INVERT on the panel.

This controller also displays Volts, Amps, Amp hours, etc.

Charge button

On/Off &

Inverter button

To use the inverter, push the Inverter button and the INV light should illuminate indicating it is functioning and there is power to outlets. If no electronics are drawing any current from the inverter, the display will read “Searching”, effectively putting the inverter on standby, saving power while it’s not in use.

This same unit is used to determine the voltage of the batteries.

The inverter power source is the DC house batteries located in the engine room.

The quantity of DC power is limited to the capacity of these batteries... Running hair dryers, toaster, coffeepots, space heater, etc. and will quickly discharge the batteries.

Use these items very sparingly as they draw a significant amount of power!

When connected to shore power, the inverter automatically becomes a battery charger for the 12-volt HOUSE BATTERIES. If the house batteries fail to charge, check the inverter control panel and make sure the charger button “CHG” is illuminated.

21

DC SYSTEM 12-VOLT

The 12 Volt DC Panel shows all the systems supported by the batteries. Primarily you will be turning on the breakers for your lights, water pressure, electronics, etc.

Bilge pumps should always be left on.

The battery banks supply 12-volt DC power. The Battery Selector Switch controls the following:

1

House battery bank and the Port engine

2 Starboard engine start battery

All All batteries [While on Shore power, or when underway, ALL should be selected; i.e. ALL batteries will be charged.]

The battery switches are located below the steps to the forward stateroom. They are normally in the ‘ON’ position. There is NO generator now but the panel still has a switch… ignore it.

Note – If necessary to switch battery positions,

do not

change the position of the switches while the engines are running or the alternator diodes along with electrical instruments could be damaged.

ONLY change position with the engines off.

BATTERIES

The HOUSE battery bank provides power for all DC systems and automatic bilge pumps. When disconnected from shore power, all 12-volt devices drain the house battery. Use devices as needed.

When a battery bank is being charged, the voltage will read from about 13.1 volts to 14.4 volts depending upon state-of-charge of the battery bank. When the battery

22

bank is at rest (i.e, not being charged), the voltmeter can give an indication of the state-of-charge of the battery bank.

Batteries are charged by the engine alternators while underway. The batteries are charged by the battery charger when connected to shore power. Ensure the Battery

Charger circuit breaker at the electrical panel is ON.

Voltage (Wet Cell

Battery)

Battery

State

12.65 volts

12.47 volts

12.25 volts

11.95 volts

11.70 volts

100%

75%

50%

25%

0%

23

SANITATION SYSTEM

VACU-FLUSH MARINE TOILET

It is important that every member of the crew be aware of the proper use of the

Vacu-Flush TOILET. It is a great system usually without problems. If you only put human waste and a tiny amount of MARINE toilet paper into the toilet, you will have NO problems. The valves, openings, and pumps are small and may clog easily. If the toilet clogs, it is YOUR RESONSIBILITY! Always monitor use by children.

There is an ON/OFF switch for the AFT head Vacu flush system. The switch is located below the Holding Tank Status panel. Turn switch ON before using the toilet. Please keep the switch OFF when the toilet is not being used.

Caution –

Never put paper towels, tampons, Kleenex, sanitary napkins, household toilet paper or food into the marine toilet. Use only the special dissolving marine toilet tissue provided by AYC.

HOLDING TANK

The holding tank holds approximately 40 gallons. Be aware of the rate of waste production, (about 1 gallon per flush). With an overfilled tank, it is possible to break a hose, clog a vent, or burst the tank. The result will be indescribable catastrophe and an EXPENSIVE FIX for you. Empty the tank at least EVERY

OTHER DAY to avoid this problem.

The holding tank is located aft of the fuel panel in the engine room. There is a

tank watch warning light located in the aft head but do not rely too greatly upon this as they are unreliable... dump often is the best strategy!

The holding tank is emptied in one of two ways, pump out or dump overboard.

24

Pump Out:

At a Marine Pump-Out Station (all around the San Juans), remove the HOLDING

TANK deck fitting located on the starboard side deck.

Holding tank pump out

Insert the pump-out nozzle into the WASTE opening. Double-check the correct deck fitting (sucking DIESEL into their sewer system is frowned upon)! Turn on pump and then open valve located on handle. When pumping finished, close lever on handle before removing from deck fitting. Turn pump off.

If there is a fresh water hose on the dock, rinse the tank by adding about 2 minutes worth of water into tank. Then pump out again to leave the tank rinsed for the next charterer. This also helps eliminate head odors.

In Canadian waters the tank contents can be discharged overboard with the

MACERATOR. If you choose to do this, instructions for opening the Y-VAVLE and operating MACERATOR follow.

25

Y-VALVE

The Y-VALVE directs waste effluent into the sanitationholding tank or flushes the effluent directly overboard.

The Y-VALVE is located behind the fuel panel in the engine room. It can be accessed via the aft hatch in the salon. A plastic tie keeps the handle pointed “TO

HOLDING TANK” – the normal position.

The Y-VALVE is wire-tied to the holding tank position by Coast Guard regulations. Please leave it “as is” unless there is an emergency. Be familiar with the applicable laws concerning dumping overboard.

Dump Overboard:

To discharge the contents of the holding tank overboard:

1. Turn the Y-VALVE so it is pointing towards the “Waste Overboard” discharge line

2. Open the thru-hull valve located on the starboard side of the holding tank. It is also marked “Waste Overboard”

3. Turn ON the MACERATOR PUMP on the DC power panel. Listen for the macerator’s sound. When the pitch becomes higher, the tank is empty. Watch for bubbles coming out from under the boat on the starboard side. It should only take a few minutes (4 max) to empty the tank. Do not run it too long as it will burn out! Usually it will be necessary to stop the engines to hear the sounds

26

WATER SYSTEM

FRESH WATER TANK

The two fresh water tanks hold 154 gallons total. They are interconnected; no valve is necessary switch between the tanks. Observe the water level visually. To refill the water tanks, open the aft hatch, remove a cap and fill. You can usually fill faster than the interconnection so it may take a bit of patience to completely fill both tanks.

FRESH WATER PRESSURE PUMP

Activate the pump by turning on the F.W. PUMP breaker on the DC electrical panel. If the water pump runs continuously, you are either out of water or might have an air lock and need to bleed the system by opening up a faucet.

If you run out of water, shut off the hot water heater on the AC Power Panel or serious damage can occur!

HOT WATER

The hot water heater is a 11 gallon tank, heated when connected to shore power from the AC Power Panel or from engine heat through a heat exchanger when underway.

To use while on shore power, turn on the WATER HEATER circuit breaker on the

AC Power Panel. Do not use the water heater if the water tank level is very low.

27

SHOWER

Water from the sinks and showers drains overboard through various thru-hulls usually located under the sinks.

Before taking a shower, turn on the DRAIN PUMP switch on the DC Power Panel.

When taking a shower, pull out the drain pump switch just below the vanity sink to activate the shower sump pump. The drain is below the waterline so a pump is required.

To conserve water, take only very short “boat” showers (turning off water between soaping up and rinsing). To keep shower tidy wipe down the shower stall. Check for accumulation of hair in the drains and remove.

WASHDOWN

A pressured fresh water washdown is available from a hose spigot in the stern on the deck. The fresh water pump must be on at the circuit breaker for it to function.

There is also a saltwater washdown located in the bow on deck. This is primarily used for cleaning off the anchor as you are lifting it back up. This pump is operated by the wash down circuit breaker, located on the DC electrical panel.

Please turn off the switch after use.

28

GALLEY

STOVE & OVEN

The stove and oven are propane. To use them, turn on the GAS STOVE circuit breaker on the DC power panel. The propane stove is activated by the following steps:

1. Turn on the propane tank located in the port side, forward, flybridge seat. Open the valve slowly so as not to trip the regulator. If you hear a “click” while opening the valve you will need to close the valve, and loosen the regulator fitting from the tank a bit to bleed the system and reset the regulator.

2. Turn on the LP GAS solenoid switch

3. Turn on the gas at the stove, press in knob and turn to IGN. While pressing the knob in, press the BURNER IGNITE button to light burner. You can also use a lighter or match. It may take a few seconds the first time to light due to the air in the line between the propane tank and the appliance. You might need to hold knob in for a few seconds while the thermocouple warms up.

29

4. To light the oven, turn the knob to the “Light” position. While pressing the red

OVEN SAFETY knob, hold a lighter or match to the pilot inside the oven. You might need to hold knob in for a few seconds while the thermocouple warms up.

When finished turn the LP GAS switch off and turn the GAS STOVE circuit breaker on the DC Power Panel to OFF.

If leaving the boat, it is a good idea to turn off the gas at the tank.

REFRIGERATOR

The refrigerator is dual voltage (12-volt and 120-volt power). It will automatically use 110-volt power when the shore power is connected.

Otherwise, it will operate on 12-volt power if the FRIDGE circuit breaker is ON.

Monitor the use of the refrigerator when the engines are not running so as NOT to run out of battery power.

30

HEATING SYSTEM

DIESEL HEATER

A new diesel forced-air furnace located in the engine room provides heat in the same way as a household furnace, from vents throughout the boat.

Move the slide switch located at the bottom of the thermostat to the right, HEAT.

Set the desired temperature using the up or down buttons to the right of the selected display. It takes a few minutes for the computers to start up the system.

Check the furnace exhaust on the port side hull mid-ship for any obstruction such as fenders or lines. Do not block this opening when operating the furnace as the heat will damage fiberglass and rubber.

Turn off the furnace heater by moving switch to OFF. The furnace will go through a “cool down” cycle, so may continue to run for a few minutes after being turned off.

ENGINE HEAT

Engine heat from an outlet aft of the port side door is available using the fan switch next to it. The two-speed fan is operated by pulling the switch out.

31

BILGE PUMPS

Gratitude has two automatic bilge pumps located in the engine room.

The master switch is located on the DC power panel. Normally, the switch will be left in the AUTO position. You may occasionally hear the pump operate due to condensation and water drips from the shaft log accumulating in the bilge.

An auxiliary hand operated bilge pump located behind the fuel panel is accessed through the aft hatch in the floor of the salon. This is used only in emergency situations but will work very well with an excited crewmember operating it!

32

ELECTRONICS

VHF RADIO

There are two VHF radios. The first is located above the helm. Make sure the

VHF breaker on the DC power panel is ON. To be able to hear the VHF, the

Shipmate speaker device located to the left of the VHF must also be turned on.

There is a second VHF radio located at the flybridge.

DEPTH SOUNDER

The DEPTH circuit breaker must be ON, The sounder should provide reliable readings in shallow waters. If in doubt, switch it off, then turn it back on to reset sounder. If your reading is blinking, it is a FALSE reading. False readings can occur at depths of more than 200 feet.

33

RADAR

To turn the radar on, please read the extensive instructions available in the Radar manual.

We do not recommend operating in reduced visibility!

GPS / PLOTTER

The GPS at the helm is controlled using the control head just below on the helm.

The PLOTTER circuit breaker must be on.

Press the power button on the control head to activate the unit.

34

ENTERTAINMENT SYSTEMS

AM/FM/CD/MP3/WMA STEREO PLAYER

The unit is located above and to the left of the helm. It operates like a normal car radio. The single CD unit is located behind the control head.

To turn the unit on, press the ATT button.

To change to source, press the SRC button.

To change the volume, turn the knob to increase or decrease the volume.

To change the radio station, push the knob left or right. “Hold” the knob to the left or right to search for a strong radio channel.

To tune to a present radio station press the knob up or down.

To play a CD, press the EJECT button and insert the CD. It will begin playing automatically.

There are two sets of stereo speakers; one set in the salon and one set on the flybridge. The salon speakers are the “front” speakers and the flybridge speakers are the “rear” speakers. To increase the volume on the flybridge, press in on the knob and select the audio function. Press the knob again and turn to select “Bal” or “Fad”. To increase the volume to the flybridge “rear” speakers, push the knob down. To increase the volume to the salon “front” speakers, push the knob up.

Push the knob left or right to change the balance.

35

ANCHORING

If you are bringing up more than 100’ of chain, it may be necessary to open the chain locker at the head of the v-berth to redistribute the chain as it may “pile-up” in the locker. Please remove the v-berth cushions and place a sorb or towel under the door before opening the chain locker to catch any water or debris.

The primary working anchor is a CQR and is attached to 200ft of chain.

The windlass power switch is located on the PROTECTION PANEL located to the right of the helm. Turn it ON. It is NOT a good practice to use the controls at the helm as it could be dangerous for the crewmember at the bow.

At the bow, tap gently on the down foot control to lower the anchor. If necessary, guide the anchor over the anchor roller to prevent binding on the pulpit.

Let out sufficient ANCHOR RODE before setting the anchor. Colored markers are placed every 25 feet on the chain as follows: Y=yellow, R=red, B=black

 25ft

 50

 75

 100

Y

R

YY

 125

 150

 200

RR

YR

BYRY

 175

RYR

 WARNING at almost the end RRR

RYRY

36

Use about 5 to 1 scope depending on the weather. Set the anchor with a gentle tugs, then verify that the anchor has held by having one engine in IDLE reverse and verify the boat is NOT moving backward.

Before raising the anchor, ALWAYS start the engines as the windlass uses a large amount of power.

Turn ON the windlass switch. As you drive the boat toward the anchor, press the

UP control to take up slack. Give the windlass short rests as you are pulling the anchor up.

As the anchor rises, be careful not to allow it to swing against the hull. Guide the anchor onto the roller

Wash down the chain if it's muddy before it goes into anchor locker to keep things smelling nice.

Turn OFF the Windlass power switch.

A spare Danforth anchor is stowed in the Lazarette.

37

MOORING BUOYS

The State Park Sticker on your vessel allows you to pick up the mooring buoys in the parks for free. You only need to register at the kiosk.

Mooring buoys have a metal triangle and at the top is a large metal ring. The metal ring is attached to a chain which secures your boat. It is very heavy. The strongest member of your crew should be picked for this job.

Come up to the buoy into the wind as you would for anchoring.

Have crew members on the bow, one with a boat hook and one with a mooring line secured like a bow line.

As you are slowly approaching the buoy, have the crew holding the boat hook point at the buoy to help guide you. It is usually very difficult to see them as it gets close under the bow.

Hook the buoy and bring the ring up to the boat to allow the second crew member to thread the ring with the line.

Lower the ring and line with the boat hook.

Now form a bridle. If your mooring line is led out of the starboard chock bring the end of the line to the port side chock. This will create a bridle with about 10 feet of slack from the chock to the buoy.

38

BARBECUE

Gratitude is equipped with a Magma Chefsmate BBQ which uses standing 1 lb. disposable propane canisters. Note: Propane bottles are not stocked by AYC.

You will need to purchase one if extras are not found on board.

The propane regulator and propane bottles are located in the aft deck locker. BBQ tools and lighter are located in the galley.

Attach the propane regulator to the barbecue by turning it (180 degrees or more) until it clicks-in. Always turn or push gently. Once it is clicked-in, it will rotate freely. Attach the propane bottle to the regulator. The propane bottle can be rotated to rest on the rail to give a better view of the valve and temperature control.

To light the BBQ:

 Open lid by turning lock lever counter-clockwise to loosen catch. Once open, turn the lock lever to the locked position so lid doesn’t catch closed

 Stick lighter through hole on the left side and light lighter

 Depress valve and turn counter-clockwise to “High”

 Visually confirm ignition

To reduce flare-up:

 Empty and clean grease tray prior to each use

 Trim excess fats from meat

 Use non-oil based marinades

 Reduce heat

Warning: Do not overheat grill. Magma Grills do not require pre-heating. When grilling on medium or high heat, grill with the lid open.

After use, please disconnect the fuel canister from the valve and remove the valve from the BBQ. Please wipe the BBQ down and clean grease tray with a paper towel to prevent grease from soiling the boat. Please replace cover once BBQ is cool to help prevent corrosion.

Caution -- For safety reasons, do not store an opened propane bottle within the salon or engine compartment. Store these bottles in the aft deck locker.

They have been known to leak slightly once opened and propane gas could settle into low areas, which can be highly dangerous!

39

DINGHY & OUTBOARD MOTOR

The Caribe Dinghy is outfitted with a 9.9 hp Honda 4 stroke and is located on the swim step. It has a capacity of approximately 1,200 total pounds (which includes, motor, equipment and up to 4 people).

The key is located in the helm drawer. Oars and located in the Lazarette. The gas tank for the outboard is located in the aft deck locker.

Davit crank and safety pin

To deploy the dinghy, first make sure your bow line has been loosened so that as the dinghy is lowered it won’t pull the line tight. Unlatch the safety pin on the crank and slowly lower the dinghy into the water using the crank on top of the pedestal. As the engine is lowered it will slip over the transom of the dinghy.

Lock the motor in position. Unlatch and enjoy! Reverse the procedure to stow it.

Before starting the outboard motor refer to the instructions below on how to lower the motor into the water.

To start outboard motor, connect the key connect the gas tank hose to the gas connection on the motor and pump the priming bulb until it is firm.

Outboard motor showing gas connection and choke

Open the choke and set the throttle up slightly. Pull the starter cord until the motor starts. If the motor has not been run in awhile, it may need to warm up for a minute or so before the choke can be set back.

40

To lower the outboard motor into the water, move the tilt/run lever located on the starboard side of the motor to the

“Run” position. Lift the motor slightly until you hear a click and then lower the motor into the water. To lift the motor out of the water, move the lever to

“Tilt” and lift the motor. It should then lock in the raised position.

Outboard motor showing tilt/run lever

If you are towing the dinghy, always keep it tight to the boat any time that you slow down or stop, Assign one of your crew members as the “dinghy” person to be responsible for taking up slack. You don’t want to wrap the line in the propeller.

Coast Guard regulations state that any child 14 and under must wear a life jacket in a dinghy. It is a good idea for everyone to follow this rule.

41

CRABBING & FISHING

Always check the fishing and crabbing requirements before you leave on your cruise.

You will need a valid Washington fishing license to participate.

Many areas are CLOSED to crabbing and fishing on certain months, read the pamphlet carefully.

CRAB AWAY FROM THE BOAT! Lines can get easily wrapped around props.

Fish-flavored cat food with the pop-up ringed lids work well for a neat and lost cost way to bait the ring. After 20-30 minutes, retrieve the crab line and ring quickly.

Measure the crab carapace using a CRAB MEASURING GAUGE.

Boil crabs in seawater, about 12 minutes should do it.

After using, please wash the equipment thoroughly with fresh water (available from the cockpit shower faucet).

Note -- Please do not store wet rings and gear inside the boat. Let it dry out a bit on deck to help keep things smelling nice.

42

THRU-HULL LOCATIONS

Engine raw water intakes are located forward of each engine.

The onboard seacocks operate on the simple “expanding plug” principle. A wingnut on the back of each valve is hand-tightened when in the valve is in the desired open or closed position. Tightening the wingnut expands the rubber plug, thus sealing the valve.

Step 1: Loosen wingnut

Step 3: Tighten wingnut

Step 2: Set the valve handle in desired position

Operation:

When a change in valve position is desired, the wingnut is loosened enabling the operator to turn the valve handle to the new position. Re-tighten the wingnut each time.

Note: While the wingnut is loose the seepage of a small amount of water is normal.

43