Moonlight Lullaby™ Moonlight Lullaby™

Moonlight Lullaby™ Moonlight Lullaby™
x2 1.5V
LR6 size
Replace with 2 x 1.5V
“AA” or LR6 size
alkaline batteries.
Phillips/cross head
screwdriver (not
included) needed to
replace batteries.
Moonlight Lullaby™™
LULLABY responds
to your child’s
touch! Just press
her tummy and
she’ll alternate
between making
cute little baby
sounds and playing
music while her
moon lights up.
NOTE: Be sure to remove sound
unit from doll before washing.
Doll and attached blanket are
machine washable. Remove sound
unit and securely close fabric fastener
on doll before washing. Place doll
in pillowcase and tie end closed.
Machine wash separately, gentle
cycle (cold water, mild detergent,
no bleach). Tumble dry promptly in
pillowcase, low heat setting.
Be sure to position sound unit with
battery door facing back of doll.
1. Open the fabric flap on doll’s
back and pull out sound unit.
2. Loosen screw on battery door.
3. Remove and discard old
4. Replace with fresh 2 x 1.5V
“AA” or LR6 size alkaline
5. Replace cover, tighten screw, and
reinsert sound unit into doll. Be
sure to position sound unit with
battery door facing back of doll.
1. Always follow the instructions carefully. Use only batteries specified
and be sure to insert them correctly by matching the + and – polarity
2. Do not mix old batteries and new batteries or standard (carbon-zinc)
with alkaline batteries.
3. Remove exhausted or dead batteries from the product.
4. Remove batteries if product is not to be played with for a long time.
5. Do not short-circuit the supply terminals.
6. Should this product cause, or be affected by, local electrical
interference, move it away from other electrical equipment. Reset
(switching off and back on again or removing and re-inserting
batteries) if necessary.
7. RECHARGEABLE BATTERIES: Do not mix these with any other types
of batteries. Always remove from the product before recharging.
Recharge batteries under adult supervision. DO NOT RECHARGE
If MOONLIGHT LULLABY is unresponsive, or if movement and sounds
become erratic, the battery power may be low. Replace batteries.
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Product and colors may vary.
© 2009 Hasbro. All Rights Reserved.
TM & ® denote U.S. Trademarks.
19435/19143 Asst.
PN 7023510000
Questions? Call 1-800-327-8264
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF