Connectors on the TR-ATX-865G
TRANSDUCTION
USER’S MANUAL
Version 1.0
07/30/08
TR-ATX-865G PENTIUM 4 INDUSTRIAL MOTHERBOARD
WITH ISA, 5 PCI AND I AGP SLOTS
5155-23 Spectrum Way, Mississauga, ON, Canada L4W 5A1
TEL: 1-800-268-0427, 905-625-1907
FAX: 905-625-0531
Email: [email protected]
Contents
Contents
1 Introduction ...................................................... 1
Checklist ..................................................................................2
Description ..............................................................................2
Features ...................................................................................4
Specifications...........................................................................5
2 Installations..................................................... 10
CPU Installation....................................................................11
Memory Installation .............................................................12
Jumpers on the TR-ATX-865G............................................13
Jumper Locations on the TR-ATX-865G...........................14
JP1 ~ 2: CPU Frequency Selector ......................................15
JP3: CMOS RAM Data ......................................................15
JP4 ,5: On-Board LAN Disable selection...........................16
COM2MODE/COM4MODE: ............................................17
COM2/COM4 RS232/RS422/RS485 Selection .................17
Connectors on the TR-ATX-865G.......................................18
Connector Locations on the TR-ATX-865G......................19
Front Panel Connector........................................................21
EIDE Connectors................................................................23
Floppy Connectors..............................................................25
Parallel Port ........................................................................26
COM1 Serial Port ...............................................................27
COM2 Serial Port ...............................................................27
COM3 Serial Port ...............................................................28
COM4 Serial Port ...............................................................28
PS/2 Keyboard & Mouse Connector ..................................29
VGA Connector.................................................................29
CPU Fan Power Connector ................................................30
Chassis Fan Power Connector ............................................30
System FAN Connector......................................................30
USB56 and USB78 Connectors..........................................31
IrDA Connector ..................................................................31
Keylock and Power-ON LED Connector ...........................31
ATX Power Connector .......................................................32
ATX_12V Power Connector ..............................................33
ii
TR-ATX-865G User Manual
Contents
LAN/USB Connectors .......................................................33
LAN- RJ45 Connectors......................................................34
LAN RJ45 LED..................................................................34
LAN LED Connectors........................................................35
Audio Connectors...............................................................35
CD_IN Connectors.............................................................35
AUX_IN Connectors..........................................................36
SUR_CEN Connectors.......................................................36
SPDIF Connectors..............................................................36
WOL Connectors ...............................................................37
SATA Connectors ..............................................................37
DIO Connectors .................................................................37
3 BIOS Configuration ....................................... 38
BIOS Introduction................................................................39
Starting Setup .....................................................................39
Using Setup ........................................................................40
Getting Help .......................................................................41
In Case of Problems ...........................................................41
Main Menu............................................................................42
Standard CMOS Features ........................................................... 42
Advanced BIOS Features ............................................................ 42
Advanced Chipset Features......................................................... 43
Integrated Peripherals ................................................................ 43
Power Management Setup........................................................... 43
PnP / PCI Configuration............................................................. 43
PC Health Status ......................................................................... 43
Frequency/Voltage Control ......................................................... 43
Load Fail-Safe Defaults .............................................................. 43
Load Optimized Defaults............................................................. 43
Supervisor / User Password ........................................................ 43
Save & Exit Setup........................................................................ 43
Exit Without Save ........................................................................ 43
Standard CMOS Setup ........................................................44
Channel 0 HDDs / Channel 1 HDDs........................................46
Drive A / Drive B...............................................................49
Video ..................................................................................49
Halt On ...............................................................................49
Advanced BIOS Features ....................................................50
Delay Prior Thermal...........................................................51
Thermal Management ........................................................51
Ch0 M.
:Maxtor 6E040L0.........................................52
iii
TR-ATX-865G User Manual
Contents
Bootable Add-in Cards .......................................................52
Virus Warning ....................................................................52
CPU L1 & L2 Cache ..........................................................53
Hyper-Threading Technology ............................................53
Quick Power On Self Test ..................................................53
First/Second/Third/Other Boot Device...............................53
Swap Floppy Drive.............................................................53
Boot Up Floppy Seek .........................................................53
Boot Up NumLock Status ..................................................54
Gate A20 Option.................................................................54
Typematic Rate Setting ......................................................54
Typematic Rate (Chars/Sec)...............................................54
Typematic Delay (Msec) ....................................................54
Security Option...................................................................54
APIC Mode.........................................................................55
MPS Version Control For OS.............................................55
OS Select For DRAM > 64MB ..........................................55
Report No FDD For WIN 95..............................................55
Advanced Chipset Features .................................................56
DRAM Settings ..................................................................56
DRAM Timing Selectable ..................................................57
CAS Latency Time .............................................................57
Active to Precharge Delay..................................................57
DRAM RAS# to CAS# Delay ............................................57
DRAM RAS# Precharge ....................................................57
Memory Frequency For......................................................58
System BIOS Cacheable.....................................................58
Video BIOS Cacheable.......................................................58
Memory Hole at 15MB - 16MB .........................................58
AGP Aperture Size (MB) ...................................................58
Init Display First.................................................................59
On-Chip VGA Setting ........................................................59
On-Chip VGA .............................................................................. 59
On-Chip Frame Buffer Size ......................................................... 59
Integrated Peripherals..........................................................60
IDE HDD Block Mode.......................................................61
IDE DMA transfer acess ....................................................61
On-Chip Primary PCI IDE .................................................61
On-Chip Secondary PCI IDE .............................................61
IDE Primary/Secondary Master/Slave PIO ........................61
IDE Primary/Secondary Master/Slave UDMA ..................62
iv
TR-ATX-865G User Manual
Contents
On-Chip Serial ATA Setting ..............................................62
SATA Mode.................................................................................. 62
On-Chip Serial ATA .................................................................... 62
Serial ATA Port0 Mode ............................................................... 62
Serial ATA Port1 Mode ............................................................... 62
USB Controller...................................................................63
USB 2.0 Controller.............................................................63
USB Keyboard Support......................................................63
USB Mouse Support ..........................................................64
AC97 Audio .......................................................................64
Onboard FDC Controller....................................................65
Onboard Serial Port 1/Port 2 ..............................................65
UART Mode Select............................................................65
RxD, TxD Active ...............................................................65
IR Transmission Delay.......................................................66
UR2 Duplex Mode .............................................................66
Onboard Parallel Port.........................................................66
Parallel Port Mode..............................................................66
EPP Mode Select................................................................66
ECP Mode Use DMA.........................................................66
PWRON After PWR-Fail...................................................66
Onboard Serial Port3/Port4 ................................................67
Serial Port 3 Use IRQ/ Port 4 Use IRQ..............................67
Power Management Setup...................................................68
Power-Supply Type............................................................68
ACPI Function ...................................................................69
Power Management............................................................69
Video Off Method ..............................................................69
Video Off In Suspend.........................................................70
MODEM Use IRQ .............................................................70
Suspend Mode....................................................................70
HDD Power Down .............................................................70
Soft-Off by PWR-BTTN....................................................70
CPU THRM-Throttling......................................................70
Wake-Up by PCI card ........................................................70
Power On By Ring .............................................................71
Wake Up On LAN .............................................................71
Resume by Alarm...............................................................71
Reload Global Timer Events ..............................................71
Primary/Secondary IDE 0/1 ....................................................... 71
FDD, LPT & COM...................................................................... 71
PCI PIRQ[A-D]#......................................................................... 71
v
TR-ATX-865G User Manual
Contents
PnP/PCI Configuration Setup .............................................72
PNP OS Installed................................................................72
Reset Configuration Data ...................................................72
Resource controlled by .......................................................73
IRQ Resources....................................................................73
Memory Resources .............................................................73
PCI/VGA Palette Snoop .....................................................73
INT Pin1 Assignment .........................................................73
INT Pin2 Assignment .........................................................73
INT Pin3 Assignment .........................................................74
INT Pin4 Assignment .........................................................74
INT Pin5 Assignment .........................................................74
INT Pin6 Assignment .........................................................74
INT Pin7 Assignment .........................................................74
INT Pin8 Assignment .........................................................74
PC Health Status...................................................................75
CPU Warning Temperature ................................................75
Current CPU Temperature..................................................75
Current System Temperature..............................................75
CPU FAN Speed.................................................................75
System FAN Speed.............................................................76
Power FAN Speed ..............................................................76
Vcore/1.5V/3.3V/5V/12V/-12V/-5V/VBAT/5VSB
Voltages..............................................................................76
Shutdown Temperature ......................................................76
Frequency/Voltage Control..................................................77
CPU Clock Ratio ................................................................77
Auto Detect DIMM/PCI ClK ...............................................77
Spread Spectrum.................................................................77
Load Fail-Safe Defaults........................................................78
Load Optimized Defaults .....................................................78
Supervisor/User Password Setting ......................................79
Exit Selecting.........................................................................80
Save & Exit Setup .............................................................80
Exit Without Saving ...........................................................80
Appendix ............................................................ 81
A. I/O Port Address Map .....................................................82
B. Interrupt Request Lines (IRQ) .......................................83
C. POST Beep........................................................................84
D. Installation of Windows NT 4.0.........................................84
vi
TR-ATX-865G User Manual
Chapter 1 Introduction
1
Introduction
This manual is designed to give you information on the TR-ATX-865G
motherboard. The topics covered in this chapter are as
follows:
♦ Checklist
♦ Description
♦ Features
♦ Specifications
1
TR-ATX-865G User Manual
Chapter 1 Introduction
Checklist
Please check that your package is complete and contains the items
below. If you discover damaged or missing items, please contact your
dealer.
9
The TR-ATX-865G Industrial Computer Board
9
1 ATA100 IDE Ribbon Cable
9
1 Floppy Ribbon Cable
9
1 Serial Port Ribbon Cable attached to a Mounting Bracket
9
1 Seria ATA cable
9
1 CD Disc Containing 865G VGA Drivers, Intel 82547 and
82541 LAN Driver, Intel chipset drivers, BIOS Update
Utility and this User`s manual.
Description
The TR-ATX-865G is a Pentium 4 Industrial Motherboard based
on Intel 865G chipset and is designed for harsh industrial environment.
It features one 478-pins Socket, which is compatible with Intel
uFC-PGA package Pentium 4 processor. This board accommodates up
to 4GB of DDR400 SDRAM memory.
The TR-ATX-865G is a high integration design. Two Intel Gigabit
Ethernet Controller, Audio AC97 Codec, SATA RAID controller are
integrated into the system. The high-integration design prevents the
system compatibility issues and increases the PCI add-on cards scalability.
This makes TR-ATX-865G an ideal Main-Board for DVR, POS,
Mini-Server, automation as well as other industrial applications.
TR-ATX-865G provides the most complete features needed for
system operation. These include Dual Gigabits LAN, AC97 5.1 channels
Audio, Dual channel UDMA100 IDE drive controller, Dual
SATA-150 ports with RAID 0 and 1 support, four high performance
serial ports, enhanced parallel port, eight USB 2.0 ports and a
programmable watchdog timer are available on-board. TR-ATX-865G also
has the maximum add-on card expansion slots on an ATX form factor.
It comes with 5 PCI slots, two ISA slots and one AGP 8X Pro slots.
2
TR-ATX-865G User Manual
Chapter 1 Introduction
What’s more, the Intel 865G on-board incorporates the latest
microprocessor technology to provide the increased bandwidth needed
to operate your system bus at speeds up to 800MHz FSB.
The TR-ATX-865G comes with integrated hardware monitoring
device that monitors system and CPU temperature, voltages of all
system power rails, and CPU fan speeds to prevent system crashes by
warning the user of adverted conditions. The power management feature
provides power savings by slowing down the CPU clock, turning off
the monitor screen and stopping the HDD spindle motor.
The rich features and long life-cycle support makes TR-ATX-865G
and idea solution for industrial applications.
3
TR-ATX-865G User Manual
Chapter 1 Introduction
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Support Pentium 4 Prescott (90nm) and Northwood (0.13um)
CPU with 400/533/800M FSB speed selectable. Intel VRD 10.1
compliant to support future advanced processor.
Four DIMM sockets support up to 4GB memory size. System
memory speed can be DDR266, 330 or 400, selectable by BIOS
setup.
Support dual channel turbo mode while identical DIMM modules
populated on both channels.
Dual SATA ports with classic IDE, RAID0 or RAID 1 mode
configurable. Rebuild supported at RAID 1 mode with Intel IAA
software.
Dual Intel Gigabit Ethernet LAN ports on-board.
Support Server-grade LAN features like Teaming,
Load-balancing and Fault-Tolerance in wire-speed.
Boot Agent with both RPL and PXE protocol support is integrated
in system BIOS for remote Boot functions.
LAN LED built-in RJ45 connector to display Speed, Link an
activities. External connector is available to display LAN status
on front Panel.
Four serious ports. Two is RS232/422/485 selectable for remote
control and data access.
AC97 3D Audio CODEC on-board support 16-bits 5.1channels
high-quality Audio System as well as S/PDIF digital interface.
Eight USB2.0 ports. Four ports on rear panel for external access
and four ports in a 2x5 box-header for internal devices connection.
Support Hardware Monitor and Watch-Dog timers. System will
alert administrators while abnormal operation condition
happened.
Support remote wake up on LAN and Modem.
Five standard 32-bits 5V PCI slot for PCI add-on card or
expansion Riser card.
One APG PRO 8X slots for high-end AGP add-on card.
Two ISA slots support up to two 16-bits ISA add-on card.
4
TR-ATX-865G User Manual
Chapter 1 Introduction
Specifications
•
Processor Socket 478 supports Intel® Pentium® 4 series
processors:
ƒ
Intel® Celeron® based on 0.13μcore, 400MHz FSB, up to
2.80GHz
ƒ
Intel® Pentium® 4 based on 0.13μcore, 512KB L2,
533MHz FSB, without HT Technology, up to 2.80 GHz
ƒ
Intel® Pentium® 4 based on 0.13μcore, 512KB L2,
533MHz FSB, with HT Technology, up to 3.06 GHz
ƒ
Intel® Pentium® 4 based on 0.13μcore, 512KB L2,
800MHz FSB, with HT Technology, up to 3.20 GHz
ƒ
Intel® Pentium® 4 based on 90nm core, 1MB L2, 533MHz
FSB, with HT Technology, up to 2.80 GHz
ƒ
Intel® Pentium® 4 based on 90nm core, 1MB L2, 800MHz
FSB, with HT Technology, up to 3.4 GHz
•
System Memory:
ƒ Four DDR DIMM Sockets support DDR 266/333/400
unregistered non-ECC Memory up to 4.0 GB.
ƒ Dual Channel Turbo mode is automatic detected by BIOS and
supported when identical DIMM module are populated on
both channels.
•
Video Controller:
ƒ 865G Integrated Intel Extreme Graphic Engine with 266MHz
Core Frequency.
ƒ VGA/UMA shares System Memory as frame buffer. Buffer
Size can be configured through BIOS setup.
ƒ High Performance and High Quality 3D graphic rendering
Engine.
ƒ Video DVD and PC-VCR support.
ƒ One 15-pins D-type connector on bracket for CRT display.
•
PIDE and SATA:
ƒ Two Enhanced PIDE interfaces for up to four devices support
PIO Mode 3/4 or Ultra ATA33/66 /100 IDE Hard Disk,
ATAPI CD-ROM and LS-120 drive.
ƒ Two SATA connectors support up to two SATA-150 HDDs.
5
TR-ATX-865G User Manual
Chapter 1 Introduction
ƒ
ƒ
Two SATA ports can be configured as RAID-0 and RAID-1
with RAID BIOS and Intel IAA drivers.
SATA RAID BIOS is integrated in System BIOS.
•
FDD Interface:
ƒ Support up to two floppy drives (360KB, 720KB, 1.2MB,
1.44MB, 2.88MB)
•
Super I/O:
ƒ Parallel Port: One high-speed parallel port with
SPP/EPP/ECP mode support.
ƒ
ƒ
Serial Port: Four16550 UART compatible ports. COM2 and
COM4 can be configured as RS232 as well as RS422/RS485
interface.
IrDA Interface: Pin-header connector for the optional IrDA
external connector
•
Gigabit and 10/100M Ethernet:
ƒ Intel 82547GI and 82541GI Ethernet controller on-boards.
ƒ Two LED to display the Speed, Link and Activity.
LINK/ACT Î GREEN ON: Link
BLINKING: Activity.
SPEED Î ORANGE: 1000M bps
GREEN: 100M bps
OFF: 10M bps
ƒ Support Teaming, load balancing and fault-tolerance with
Intel Bay-City 3.0 drivers.
ƒ Support Wake-on-LAN while ATX power supply is attached.
•
CMOS:
ƒ On-board RTC with 242 bytes of Battery-back CMOS RAM.
ƒ One 3-pins Jumper to clear CMOS data.
•
Audio:
ƒ RealTek ALC655 AC97 Audio chip on-board.
ƒ One 3-in-1 stack-up phone jacks on rear for Line-IN,
Line-OUT and MIC cabling.
ƒ One CD-ROM Audio-In and One AUX-In 4-pins connector
on-board.
ƒ One SUR_CEN connector for Surround and Center Speakers.
ƒ One SPDIF connector for SPDIF input and output
connection.
•
BIOS:
6
TR-ATX-865G User Manual
Chapter 1 Introduction
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Phoenix-Award Standard PnP BIOS 6.2.
4Mbit FlashROM with BootBlock for Fail-safe.
Enhanced ACPI and DMI2.0 compliant.
BIOS utility for field update.
VBIOS and LAN remote Boot Agent integrated.
32-pins PLCC type socket for easy field replacement.
•
ISA and PCI Expansion Slot:
ƒ Five 5V 32-bits PCI slots.
ƒ One AGP PRO 8X slots
ƒ Two ISA 16-bits slots.
•
Power Connector:
ƒ One ATX12V 2x2 connector on-board to support CPU
Vcore power.
ƒ One ATX 20pins connector on-board to support system
power.
•
Cooling:
ƒ One CPU cooling FAN connector near by CPU socket.
ƒ One Power colling FAN connector near by ATX PSU.
ƒ Two System cooling FAN connectors on the Front.
•
USB Interface:
• Eight USB ports compliant with USB Specification Rev. 2.0
and support USB Hot-Plug function.
• Four ports on rear penal with type-A connector for external
USB devices.
• Four ports in two 2x5 box header for internal USB devices
connection.
• Support Legacy USB devices and Boot from USB devices
like USB-HDD, USB-Floppy and USB-CDROM.
• USB Keyboards and Mouse are supported and can be enabled
by BIOS setup.
•
Hardware Monitor System:
ƒ PC Health Monitoring ASIC supports system power voltages,
FAN speed and system temperatures monitoring.
•
Keyboard and Mouse connectors:
ƒ Dual Mini-DIN connectors on rear panel for PS2 type
keyboard and mouse connection.
ƒ All USB ports support USB type keyboard and mouse.
7
TR-ATX-865G User Manual
Chapter 1 Introduction
•
Digital Input and Output::
ƒ Support 8-bits Digital I/O.
ƒ Software programmable to configure as 4-IN/4-OUT or 8-IN
or 8-OUT.
ƒ All DIO bits are 5V-tolerance.
•
Environmental and Mechanical:
ƒ Power Supply:[email protected]+5v typical; [email protected] +12v typical;
[email protected] -12V typical; [email protected] +5VSTB
ƒ Temperature: 0C to 60C operating; -40C to 70C storage
ƒ Humidity: 5% to 95%
ƒ Dimensions: 9.6”(L) x 12” (W); or 244mm (L) x 305mm(W)
8
TR-ATX-865G User Manual
Chapter 1 Introduction
This page is intentionally left blank.
9
TR-ATX-865G User Manual
2
Installations
This chapter provides information on how to use the jumpers and
connectors on the TR-ATX-865G in order to set up a workable system.
The topics covered are:
CPU Installation .....................................................................11
Memory Installation ...............................................................12
Jumpers on the TR-ATX-865G..............................................13
Connectors on the TR-ATX-865G.........................................18
10
TR-ATX-865G User Manual
Chapter 2 Installations
CPU Installation
The TR-ATX-865G Industrial SBC Card provides a 478-pins ZIF
socket for Pentium 4 processors with FC-PAG2 package.
To Install a CPU, first turn off your system and remove its cover. Locate
the ZIP socket and open it by first pulling the lever sideways away from
the socket then upwards to a 90-degree right angle. Insert the CPU with
the correct orientation. Use the notched corner of the CPU with the white
dot as your guide. The white dot should point towards the end of the
lever. Notice that there is a blank area where one hole is missing from
that corner of the square array of pin holds. Because the CPU has a
corner pin for three of the four corners, the CPU will only fit in one
orientation. With the added weight of the CPU fan, no force is required
to insert the CPU. Once completely inserted, hold down on the fan and
close the socket lever.
To disassembly the processor, simply pull the lever sideways away from
the socket then upward to a 90-degree right angle. You can take the CPU
out from the socket without help of any tool.
After installing the processor into the Socket, ensure that the CPU fan is
installed first. Without a fan circulating air on the CPU, the CPU can
overheat and cause damage to both CPU and SBC card.
WARNING!: If no FAN circulating Air on the CPU, the processor
might been overheated and damage both CPU and SBC components.
IMPORTANT: You must set jumpers for “CPU FSB speed” depending
on the CPU that you install.
11
TR-ATX-865G User Manual
Chapter 2 Installations
Memory Installation
The TR-ATX-865G Industrial CPU Card provides two 184-pin DIMM
sockets for a maximum total memory of 2GB SDRAM. The memory
modules can come in sizes of 128MB, 256MB, 512MB and 1GB
SDRAM.
The TR-ATX-865G Industrial CPU Card supports two 184-pin DIMM
(Dual In-line Memory Module) sockets. In populating the DIMM sockets,
DIMM1 bank should be populated first for less signal reflection.
However, we do not see any issue while populate DIMM2 only. Refer to
the following table on how to configure the memory.
NOTE: Use SDRAM modules with PC2100 specification when running
DDR266 Memory bus speed. With DDR200 Memory bus speed, SDRAM
modules meet PC1600 or PC2100 specification can be used.
184-pin DIMM (2.5V) Unregistered SDRAM
Bank0
Bank1
Total Memory
(DIMM1)
(DIMM2)
128MB
256MB
512MB
1GB
128MB
128MB
128MB
256MB
256MB
256MB
256MB
512MB
512MB
512MB
512MB
1GB
----------------128MB
256MB
512MB
128MB
256MB
512MB
1GB
128MB
256MB
512MB
1GB
1GB
128MB
256MB
512MB
1GB
256MB
384MB
640MB
384MB
512MB
768MB
1280MB
640MB
768MB
1GB
1536MB
2GB
12
TR-ATX-865G User Manual
Chapter 2 Installations
Jumpers on the TR-ATX-865G
The jumpers on the TR-ATX-865G allow you to configure your SBC
card according to the needs of your applications. If you have doubts
about the best jumper configuration for your needs, contact your dealer
or sales representative. The following table lists the jumpers on
TR-ATX-865G and their respective functions.
Jumper Locations on the TR-ATX-865G.......................... 14
JP1~2: CPU Bus Speed Selector........................................ 15
JP3: Clear CMOS RAM Data ............................................ 15
JP4 ,5: On-Board LAN Disable selection ......................... 16
COM2MODE/COM4MODE: RS232/RS422/RS485
Selection............................................................................. 17
13
TR-ATX-865G User Manual
Chapter 2 Installations
Jumper Locations on the TR-ATX-865G
JP1 JP2
COM2MODE
JP3
COM4MODE
14
TR-ATX-865G User Manual
Chapter 2 Installations
JP1 ~ 2: CPU Frequency Selector
JP1 and JP2 are used to select the CPU FSB speed. It can be 400MT/s,
533MT/s or 800MT/s. User should select the correct FSB speed to make
their CPU run on correct speed and ensure the system runs stably.
JP1~JP2
Setting
Function
JP1: Pin 1-2 Short
JP2: Pin 1-2 Short
400MT/s CPU FSB
JP1: Pin 1-2 Open
JP2: Pin 1-2 Short
533MT/s CPU FSB
JP1: Pin 1-2 Short
JP2: Pin 1-2 Open
800MT/s CPU FSB
JP3: CMOS RAM Data
This 3-pin Jumper allows the user to disconnect the built-in 3V battery
power to clear the information stored in the CMOS RAM. To clear the
CMOS data: (1) Turn off the system power, (2) Remove Jumper cap
from pin1&2, (3) Short the pin2 and pin3 for three seconds, (4) Put
Jumper cap back to pin1& 2. (5) Turn on your computer, (6) Hold Down
<Delete> during bootup and enter BIOS setup to enter your preferences.
JP3
Setting
Pin 1-2
Short/Closed
Pin 2-3
Short/Closed
15
Function
Normal Operation
(default)
Clear CMOS
Content
TR-ATX-865G User Manual
Chapter 2 Installations
JP4 ,5: On-Board LAN Disable selection
On-Board Gigabit Ethernet LAN chips can be disabled by shorting the
JP4 or/and JP5 jumper.
Port #
Disable
LAN 1
JP4
LAN 2
JP5
16
TR-ATX-865G User Manual
Chapter 2 Installations
COM2MODE/COM4MODE:
COM2/COM4 RS232/RS422/RS485 Selection
COM2 and COM4 can be configured as RS232/RS-422/RS485 mode.
Below is the Jumper setting table for each mode.
COM2MODE
I/F TYPE
RS-232
RS-422
RS-485
17
TR-ATX-865G User Manual
Chapter 2 Installations
Connectors on the TR-ATX-865G
The connectors on the TR-ATX-865G allow you to connect external
devices such as keyboard, floppy disk drives, hard disk drives, printers
and etc. The following table lists the connectors on TR-ATX-865G and
their respective page number.
Connector Locations on the TR-ATX-865G......................19
Front Panel Connector........................................................21
EIDE Connectors ............................................................. 23
Floppy Connectors ............................................................ 25
Parallel Port........................................................................26
COM1 Serial Port...............................................................27
COM2 Serial Port...............................................................27
COM3 Serial Port...............................................................28
COM4 Serial Port...............................................................28
PS/2 Keyboard & Mouse Connector..................................29
VGA Connector .................................................................29
CPU Fans Power Connector...............................................30
Chassis Fan Power Connector............................................30
System Fan Connector .......................................................30
USB56 and USB78 Connectors .........................................31
IrDA Connector..................................................................31
Keylock and Power-ON LED Connector...........................31
ATX Power Connector.......................................................32
ATX_12V Power Connector..............................................33
LAN/USB Connectors .......................................................33
LAN- RJ45 Connectors......................................................34
LAN RJ45 LED..................................................................34
LAN LED Connectors.......................................................35
Audio Connectors...............................................................35
CD-IN Connectors .............................................................35
AUX_IN Connectors..........................................................36
SUR_CEN Connectors...................................................... 36
SPDIF Connectors..............................................................36
WOL Connectors ...............................................................37
SATA Connectors ..............................................................37
Dio Connectors ..................................................................37
18
TR-ATX-865G User Manual
Chapter 2 Installations
Connector Locations on the TR-ATX-865G
LAN1
USB12
AUX_IN
AUDIO
COM2
LAN2
USB34
VGA
LPT
COM1
CD_IN
PCI1
PCI2
PCI3
PCI4
PCI5
ISA1
ISA2
COM3
DIO
COM4
USB56
USB78
FLOPPY
SYSFAN2
SYSFAN1
LAN2LED
LAN1LED
19
TR-ATX-865G User Manual
Chapter 2 Installations
SPDIF
SUR_CEN
AGP
KB+MS
ATX12V
IDE2
IDE1
CPU
FAN
DDR1
DDR2
DDR3
DDR4
WOL
SATA1
IRDA
KEYLOCK
SATA2
PWRFAN
Front
Panel
ATX PWR
20
TR-ATX-865G User Manual
Chapter 2 Installations
Front Panel Connector
The front panel of the case has a control panel, which provides light
indication of the computer activities and switches to change the
computer status.
EXT
PWR
HDDLED BTM
¾
HDD
LED
RESET KEYLOCK
EXTHDDLED
This 2-pin connector is used to display the activities of storage
devices which controlled by storage add-on cards like SCSI or
SATA add-on cards. Pull low any one of two pins will make
HDD-LED light up.
EXT
HDDLED
¾
PWR
LED
IDE LED
Pin #
Signal Name
1
2
EXTLEDEXTLED-
ATX Power ON/OFF Button
This 2-pin connector acts as the “Power Supply On/Off Switch” on
the TR-ATX-865G MB. When pressed, the switch will force the MB
to power on. When pressed again, it will force the MB to power off.
PWR
BTN
21
IDE LED
Pin #
Signal Name
3
4
PWR-BTN
GND
TR-ATX-865G User Manual
Chapter 2 Installations
¾
IDE Hard Disk LED Connector
This connector connects to the hard drive activity LED on control
panel. This LED will flash when the HDD is being accessed.
HDD
LED
¾
5
6
IDE_ACT
Ground
PWR BTN
Pin #
Signal Name
7
8
+5V
Ground
RESET Switch
The reset switch allows the user to reset the system without turning
the main power switch off and then on. Orientation is not required
when making a connection to this header.
RESET
¾
Signal Name
Power-On LED
This connector allows users to connect to Front Panel Power
indicator.
PWR
LED
¾
IDE LED
Pin #
RESET
Pin #
Signal Name
9
10
Reset
Ground
Keylock
For security or other purpose, short these two pins together will
disable the keyboard functions.
KEY
LOCK
22
PWR BTN
Pin #
Signal Name
11
12
KeylockGND
TR-ATX-865G User Manual
Chapter 2 Installations
EIDE Connectors
Primary IDE Connector
Signal Name
Pin #
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
DRQ0
Host IOW
Host IOR
IOCHRDY
DACK0
IRQ14
Address 1
Address 0
Chip select 0
Activity
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
23
Pin #
Signal Name
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Key
Ground
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
TR-ATX-865G User Manual
Chapter 2 Installations
Secondary IDE Connector
Signal Name
Pin #
Pin #
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
DRQ1
Host IOW
Host IOR
IOCHRDY
DACK1
IRQ15
Address 1
Address 0
Chip select 0
Activity
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
24
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Signal Name
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Key
Ground
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
TR-ATX-865G User Manual
Chapter 2 Installations
Floppy Connectors
Floppy connector is a 34-pin header and will support up to 2.88MB
floppy drives.
Signal Name
Pin #
Pin #
Signal Name
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
DRVDE0
NC
DRVDE1
INDEXMTR0DR1DR0MTR1DIRSTEPWDATAWGATETRK0WRPRORDATAHDSELDSKCH-
25
TR-ATX-865G User Manual
Chapter 2 Installations
Parallel Port
The following drawing shows the location of Parallel port, COM1 and VGA
connector.
The following table describes the pin out assignments of parallel connector.
Signal Name
Pin #
Pin #
Signal Name
Line printer strobe
PD0, parallel data 0
PD1, parallel data 1
PD2, parallel data 2
PD3, parallel data 3
PD4, parallel data 4
PD5, parallel data 5
PD6, parallel data 6
PD7, parallel data 7
ACK, acknowledge
Busy
Paper empty
Select
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
AutoFeed
Error
Initialize
Select
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
N/A
26
TR-ATX-865G User Manual
Chapter 2 Installations
COM1 Serial Port
COM1, a 9-pin D-Sub male connector, is the onboard COM1 serial port
of the TR-ATX-865G. The following table shows its pin assignments.
Pin #
Signal Name
1
2
3
4
5
6
7
8
9
DCD, Data carrier detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal ready
GND, ground
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
COM2 Serial Port
COM2, a 10-pin header connector, is the onboard COM2 serial port of
the TR-ATX-865G. It can be configured as RS233, RS422 and RS485
mode. User can use COM2MOD jumpers to setup the operation mode.
The following table shows its pin assignments of respective mode.
Pin
#
RS232 Mode
Signal Name
RS422/RS485 Mode
Signal Name
1
DCD, Data carrier
detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal
ready
GND, ground
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
N.C.
TX- (422/485)
2
3
4
5
6
7
8
9
10
27
TX+ (422/485)
RX+ (422)
RX- (422)
GND
N.C.
N.C.
N.C.
N.C.
N.C.
TR-ATX-865G User Manual
Chapter 2 Installations
COM3 Serial Port
COM3, a 10-pin header connector, is the onboard COM3 serial port of
the TR-ATX-865G. The following table shows its pin assignments.
Pin
RS232 Mode
#
Signal Name
1 DCD, Data carrier detect
2
RXD, Receive data
3
TXD, Transmit data
4 DTR, Data terminal ready
5
GND, ground
6
DSR, Data set ready
7
RTS, Request to send
8
CTS, Clear to send
9
RI, Ring indicator
10
N.C.
COM4 Serial Port
COM4, a 10-pin header connector, is the onboard COM2 serial port of
the TR-ATX-865G. It can be configured as RS233, RS422 and RS485
mode. User can use COM4MOD jumpers to setup the operation mode.
The following table shows its pin assignments of respective mode.
Pin
RS232 Mode
RS422/RS485 Mode
#
Signal Name
Signal Name
1
2
3
4
5
6
7
8
9
10
DCD, Data carrier
detect
RXD, Receive data
TXD, Transmit data
DTR, Data terminal
ready
GND, ground
DSR, Data set ready
RTS, Request to send
CTS, Clear to send
RI, Ring indicator
N.C.
28
TX- (422/485)
TX+ (422/485)
RX+ (422)
RX- (422)
GND
N.C.
N.C.
N.C.
N.C.
N.C.
TR-ATX-865G User Manual
Chapter 2 Installations
PS/2 Keyboard & Mouse Connector
The following table describes the pin assignment of PS/2 Keyboard and
Mouse connector.
Pin #
Signal Name
1
2
3
4
5
6
Keyboard/Mouse data
NC
GND
5V
Keyboard/Mouse clock
GND
VGA Connector
The pin assignments of VGA CRT connector are as follows:
Signal Name
Pin
Pin
Signal Name
Red
Blue
GND
GND
N.C.
N.C.
HSYNC
NC
1
3
5
7
9
11
13
15
2
4
6
8
10
12
14
Green
N.C.
GND
GND
GND
N.C.
VSYNC
29
TR-ATX-865G User Manual
Chapter 2 Installations
CPU Fan Power Connector
This is a 3-pin header for the CPU fan. The fan must be a 12V fan.
3 2 1
Pin #
Signal Name
1
Rotation
2
2
3
+12V
+12V
Ground
Chassis Fan Power Connector
This is a 3-pin header for the chassis fan. The fan must be a 12V fan.
3 2 1
Pin #
Signal Name
1
Rotation
2
3
+12V
Ground
System FAN Connector
This is a 3-pin header for the system fan. The fan must be a 12V fan.
3 2 1
30
Pin #
Signal Name
1
Rotation
2
3
+12V
Ground
TR-ATX-865G User Manual
Chapter 2 Installations
USB56 and USB78 Connectors
The following table shows the pin outs of the USB connectors.
1
2
3
4
5
6
7
8
9
10
USB1
Pin#
USB0
Pin #
Signal Name
10
9
8
7
6
1
2
3
4
5
+5V
USBUSB+
Ground
N.C.
IrDA Connector
This connector is used for an IrDA connector for wireless
communication.
+5V IRRX IRTX
FIR
IrDA Pin #
Signal Name
1
2
3
4
5
+5V
FIR
Ir RX
Ground
Ir TX
GND
Keylock and Power-ON LED Connector
The Power LED provide a interface to wire the system power on signal
to front panel. The keylock switch, when closed, will disable the
keyboard function.
Power LED
Signal Name
Pin #
1
5
1
2
3
4
5
31
Power_on
NC
Ground
Keylock
Ground
TR-ATX-865G User Manual
Chapter 2 Installations
ATX Power Connector
The ATX power connector supplies power to the whole Main board.
32
Pin #
Signal Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
3.3V
3.3V
GND
VCC
GND
VCC
GND
Power Good
5VSB(stand by +5V)
+12V
3.3V
-12V
GND
PS_ON(softOn/Off)
GND
GND
GND
-5V
VCC
VCC
TR-ATX-865G User Manual
Chapter 2 Installations
ATX_12V Power Connector
The ATX_12V power connector mainly supplies power to the CPU.
Caution!
If the ATX_12V power connector is not connected, the system will not
start.
ATX_12V
Pin #
Signal Name
1
2
3
4
GND
GND
+12V
+12V
LAN/USB Connectors
Below pictures show the location of LAN RJ45 ports and USB Type-A ports on
the Combo RJ45+ USB connector.
Before you connect your device(s) into USB connector(s), please make
sure your device(s) such as USB keyboard, mouse, scanner, zip,
speaker..etc. Have a standard USB interface. Also make sure your OS
supports USB controller.
If your OS does not support USB controller, please contact OS vendor
for possible patch or driver upgrade. For more information please
contact your OS or device(s) vendors.
33
TR-ATX-865G User Manual
Chapter 2 Installations
LAN- RJ45 Connectors
This connector is for the Giga-Bit and 10/100Mbps Ethernet capability
of the Main Board. The figure below shows the pin out assignments of
this connector and its corresponding input jack.
Pin #
Signal
Name
1
2
3
4
5
6
7
8
MDI0+
MDI0MDI1+
MDI1MDI2+
MDI2MDI3+
MDI3-
LAN RJ45 LED
The LAN LED on top of RJ45 are to display the current network
connection status. The green color LED on the right-hand side shows the
link status and TX/RX activity. The Yellow/Green Dual color LED on
the left-hand side indicates the operation mode, i.e. 10Base-T,
100Base-T or 1000Base-T.
LNK/ACT
STATUS
ON
OFF
FLASH
Link
Disconnected
Packets TX/RX
SPEED
MODE
Orange
Green
OFF
1 Gbps
100 Mbps
10 Mbps
34
TR-ATX-865G User Manual
Chapter 2 Installations
LAN LED Connectors
The 4-pins LANLED connector designed for each LAN port is for
applications need to display LAN port status on front panel or the places
administrators are easy to access.
LAN LED
Pin #
Signal Name
1
2
3
4
ACTLINKSPD1GSPD100M-
LAN LED
Audio Connectors
After install onboard audio driver, you may connect speaker to Lin Out
jack, microphone to MIC In jack. Audio sources devices like CD-ROM,
walkman and etc can be connected to Lin-In jack.
CD_IN Connectors
CD_IN connector is designed for wire the CD_ROM audio signals to the
on-board Audio CODEC.
35
LAN LED
Pin #
Signal Name
1
2
3
4
CD_Left
GND
GND
CD_Right
TR-ATX-865G User Manual
Chapter 2 Installations
AUX_IN Connectors
AUX_IN connector allows you to receive stereo audio inputs from
sound sources such as a TV-Tuner, MPEG card, or CDROM.
LAN LED
Pin #
Signal Name
1
2
3
4
AUX_L
GND
GND
AUX_R
SUR_CEN Connectors
SUR_CEN connector is to support Center Speaker, Rear Surround
Speakers and Low-Frequency Speakers.
Signal Name
Pin
Pin
Signal Name
SURR_OUTL
GND
CENTER_OUT
1
3
5
2
4
6
SURR_OUTR
KEY
LFE_OUT
SPDIF Connectors
SPDIF connector is for S/PDIF audio module that allow digital instead
of analog sound input or output.
Signal Name
Pin
Pin
Signal Name
VCC
S_OUT
GND
1
3
5
2
4
6
KEY
S_IN
GND
36
TR-ATX-865G User Manual
Chapter 2 Installations
WOL Connectors
This connector provide the interface between LAN card or Modem card
to wake up system when wake packet or ring-in signals coming in.
Pin #
1
Signal Name
5VSB
2
3
GND
PME-
3 2 1
SATA Connectors
These next generation connectors support the thin Serial SATA cables
for Serial ATA Hard disks.
1
7
Pin #
Signal Name
1
2
3
4
5
6
7
GND
SATARX+
SATARXGND
SATATXSATATX+
GND
DIO Connectors
DIO port support 8 digital I/O bits. Each bit can be configured as Input or
outputs individually. All bits are 5V tolerant.
Signal Name
Pin #
Pin #
Signal Name
+5V
DIO_0
DIO_1
DIO_2
DIO_3
1
3
5
7
9
2
4
6
8
10
GND
DIO_4
DIO_5
DIO_6
DIO_7
37
TR-ATX-865G User Manual
3
BIOS Configuration
This chapter describes the different settings available in the Award
BIOS that comes with the TR-ATX-865G CPU card. The topics
covered in this chapter are as follows:
BIOS Introduction .................................................................. 39
Main Menu ............................................................................. 42
Standard CMOS Setup ........................................................... 44
Advanced BIOS Features ....................................................... 50
Advanced Chipset Features .................................................... 56
Integrated Peripherals............................................................. 60
Power Management Setup...................................................... 68
PnP/PCI Configurations ......................................................... 72
PC Health Status..................................................................... 75
Frequency/Voltage Control .................................................... 77
Load Fail-Safe Defaults.......................................................... 78
Load Optimized Defaults ....................................................... 78
Supervisor/User Password Setting ......................................... 79
Exit Selecting ......................................................................... 80
38
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
BIOS Introduction
This Chapter discusses Award™ Setup program built into the P4SVLL
BIOS. The Setup program allows users to modify the basic system
configuration.
This special information is then stored in
battery-backed RAM so that it retains the Setup information when the
power is turned off.
The AwardBIOS™ installed in P4SVLL SBC is a custom version of an
industry standard BIOS. This means that it supports Intel PentiumIV in
a standard IBM-AT compatible input/output system. The BIOS
provides critical low-level support for standard devices such as disk
drives and serial and parallel ports.
It also adds non-standard, features such as virus and password
protection as well as special support for detailed fine-tuning of the
chipset controlling the entire system.
The rest of this chapter is intended to guide you through the process of
configuring your system using Setup.
Starting Setup
The AwardBIOS™ is immediately activated when you first power on
the computer. The BIOS reads the system information contained in the
CMOS and begins the process of checking out the system and
configuring it. When it finishes, the BIOS will seek an operating
system on one of the disks and then launch and turn control over to the
operating system.
While the BIOS is in control, the Setup program can be activated in one
of two ways:
1.
By pressing <Del> immediately after switching the system on, or
2.
by pressing the <Del> key when the following message appears
briefly at the bottom of the screen during the POST (Power On
Self-Test).
Press DEL to enter SETUP.
If the message disappears before you respond and you still wish to enter
Setup, restart the system to try again by turning it OFF then ON or
pressing the "RESET" button on the system case. You may also restart
by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys. If you
39
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
do not press the keys at the correct time and the system does not boot,
an error message will be displayed and you will again be asked to...
PRESS F1 TO CONTINUE, DEL TO ENTER SETUP
Using Setup
In general, you use the arrow keys to highlight items, press <Enter> to
select, use the PageUp and PageDown keys to change entries, press
<F1> for help and press <Esc> to quit. The following table provides
more detail about how to navigate in the Setup program using the
keyboard.
Key
Up Arrow
Down Arrow
Left Arrow
Right Arrow
Esc
Move Enter
PgUp key
PgDn key
+ key
- key
Esc key
F1 key
F5 key
F6 key
F7 key
F10 key
Function
Move to the previous item
Move to the next item
Move to the item on the left (menu bar)
Move to the item on the right (menu bar)
Main Menu: Quit without saving changes
Submenus: Exit Current page to the next higher level
menu
Move to the item you desired
Increase the numeric value or make changes
Decrease the numeric value or make changes
Increase the numeric value or make changes
Decrease the numeric value or make changes
Main Menu -- Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu
-- Exit current page and return to Main Menu
General help on Setup navigation keys
Load previous values from CMOS
Load the fail-safe defaults from BIOS default table
Load the optimized defaults
Save all the CMOS changes and exit
Navigating through the menu bar
Use the left and right arrow keys to choose the menu you want to be in.
To display a sub menu
Use the arrow keys to move the cursor to the sub menu you want. Then
press <Enter>. A “¾” pointer marks all sub menus.
40
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
Getting Help
Press F1 to pop up a small help window that describes the appropriate
keys to use and the possible selections for the highlighted item. To exit
the Help Window press <Esc> or the F1 key again.
In Case of Problems
If, after making and saving system changes with Setup, you discover
that your computer no longer is able to boot, the AwardBIOS™
supports an override to the CMOS settings which resets your system to
its defaults.
The best advice is to only alter settings that you thoroughly understand.
To this end, we strongly recommend that you avoid making any
changes to the chipset defaults. These defaults have been carefully
chosen by both Award and TR-ATX-865G manufacturer to provide
the absolute maximum performance and reliability. Even a seemingly
small change to the chipset setup has the potential for causing you to
use the override.
41
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
Main Menu
Once you enter the AwardBIOS™ CMOS Setup Utility, the Main
Menu will appear on the screen. The Main Menu allows you to select
from several setup functions and two exit choices. Use the arrow keys
to select among the items and press <Enter> to accept and enter the
sub-menu.
Phoenix – AwardBIOS CMOS Setup Utility
¾
Standard CMOS Features
¾
¾
Advanced BIOS Features
Load Fail-Safe Defaults
¾
Advanced Chipset Features
Load Optimized Defaults
¾
Integrated Peripherals
Set Supervisor Password
¾
Power Management Setup
Set User Password
¾
PnP/PCI Configurations
Save & Exit Setup
¾
PC Health Status
Exit Without Saving
Frequency/Voltage Control
↑ ↓ ← → : Select Item
Esc : Quit
F10 : Save & Exit Setup
Time, Date, Hard Disk Type….
Note that a brief description of each highlighted selection appears at the
bottom of the screen.
Setup Items
The main menu includes the following main setup categories.
Standard CMOS Features
Use this menu for basic system configuration.
Advanced BIOS Features
Use this menu to set the Advanced Features available on your system.
42
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
Advanced Chipset Features
Use this menu to change the values in the chipset registers and optimize
your system's performance.
Integrated Peripherals
Use this menu to specify your settings for integrated peripherals.
Power Management Setup
Use this menu to specify your settings for power management.
PnP / PCI Configuration
Use this menu to set up the PnP/PCI configuration.
PC Health Status
Use this menu to display the CPU temperature, FAN speed and
voltages.
Frequency/Voltage Control
Use this menu to specify your settings for frequency/voltage control.
Load Fail-Safe Defaults
Use this menu to load the BIOS default values for the minimal/stable
performance for your system to operate.
Load Optimized Defaults
Use this menu to load the BIOS default values that are factory settings
for optimal performance system operations. While Award has designed
the custom BIOS to maximize performance, the factory has the right to
change these defaults to meet their needs.
Supervisor / User Password
Use this menu to set User and Supervisor Passwords.
Save & Exit Setup
Save CMOS value changes to CMOS and exit setup.
Exit Without Save
Abandon all CMOS
value
43
changes
and
exit
setup.
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
Standard CMOS Setup
The items in Standard CMOS Setup Menu are divided into 10
categories. Each category includes no, one or more than one setup
items. Use the arrow keys to highlight the item and then use the
<PgUp> or <PgDn> keys to select the value you want in each item.
Phoenix – AwardBIOS CMOS Setup Utility
Standard CMOS Features
Item Help
Date:
Time:
¾
¾
¾
¾
Mon, Feb 8 2004
16 : 19 : 20
Menu Level
IDE Channel 0 Master
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
[Maxtor 6E040L0]
[None]
[None]
[None]
Drive A
Drive B
[1.44M, 3.5 in.]
[None]
Video
Halt On
[EGA/VGA]
[All , But Disk/Key]
Base Memory
Extended Memory
Total Memory
¾
Change the day, month,
year and century
640K
1046528K
1047552K
↑↓←→Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
44
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
This table shows the selections that you can make on the
Standard CMOS Menu
Item
Date
Options
Month
DD YYYY
Time
IDE Channel 0 Master
HH : MM : SS
Options are in its sub menu
IDE Channel 0 Slave
Options are in its sub menu
IDE Channel 1 Master
Options are in its sub menu
IDE Channel 1 Slave
Options are in its sub menu
Drive A
Drive B
Base Memory
None
360K, 5.25 in
1.2M, 5.25 in
720K, 3.5 in
1.44M, 3.5 in
2.88M, 3.5 in
EGA/VGA
CGA 40
CGA 80
MONO
All Errors
No Errors
All, but Keyboard
All, but Diskette
All, but Disk/Key
N/A
Extended Memory
N/A
Total Memory
N/A
Video
Halt On
45
Description
Set the system date.
Note that the ‘Day’ automatically
changes when you set the date
Set the system time
Press <Enter> to enter the sub
menu of detailed options
Press <Enter> to enter the sub
menu of detailed options
Press <Enter> to enter the sub
menu of detailed options
Press <Enter> to enter the sub
menu of detailed options
Select the type of floppy disk drive
installed in your system
Select the default video device
Select the situation in which you
want the BIOS to stop the POST
process and notify you
Displays the amount of
conventional memory detected
during boot up
Displays the amount of extended
memory detected during boot up
Displays the total memory
available in the system
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
Channel 0 HDDs / Channel 1 HDDs
The IDE adapters control the hard disk drive. Use a separate sub menu
to configure each hard disk drive. Figure 2 shows the IDE primary
master sub menu.
Phoenix – AwardBIOS CMOS Setup Utility
IDE Cannel 0 Master
Item Help
IDE HDD Auto-Detection
[Press Enter]
IDE Channel 0 Master
Access Mode
[Auto]
[Auto]
Capacity
41111 MB
Cylinder
Head
Precomp
Landing Zone
Sector
19679
16
0
19678
255
Menu Level
¾¾
To auto-detect the HDD’s
size, head... on this channel
↑↓←→Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
Phoenix – AwardBIOS CMOS Setup Utility
IDE Cannel 0 Slave
Item Help
IDE HDD Auto-Detection
[Press Enter]
IDE Channel 0 Slave
Access Mode
[Auto]
[Auto]
Capacity
0 MB
Cylinder
Head
Precomp
Landing Zone
Sector
0
0
0
0
0
Menu Level
¾¾
To auto-detect the HDD’s
size, head... on this channel
↑↓←→Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
Use the legend keys to navigate through this menu and exit to the main
menu. Use the Table listed below to configure the hard disk.
46
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
Item
IDE HDD
Auto-detection
Options
Press Enter
IDE Channel 0 Master
None
Auto
Manual
Capacity
Auto Display your
disk drive size
Access Mode
Description
Press Enter to auto-detect the
HDD on this channel. If
detection is successful, it fills the
remaining fields on this menu.
Selecting ‘manual’ lets you set
the remaining fields on this
screen. Selects the type of fixed
disk. "User Type" will let you
select the number of cylinders,
heads, etc.
Note: PRECOMP=65535 means
NONE !
Disk drive capacity
(Approximated). Note that this
size is usually slightly greater
than the size of a formatted disk
given by a disk checking
program.
Choose the access mode for this
hard disk
CHS
LBA
Large
Auto
The following options are selectable only if the ‘IDE Channel 0 Master’ item is
set to ‘Manual’
Cylinder
Min = 19679
Set the number of cylinders for
Max = 65535
this hard disk.
Head
Min = 16
Set the number of read/write
Max = 255
heads
Precomp
Min = 0
**** Warning: Setting a value of
Max = 65535
65535 means no hard disk
Landing zone
Min = 19678
****
Max = 65535
Sector
Min = 255
Number of sectors per track
Max = 255
47
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
Item
IDE HDD
Auto-detection
IDE Channel 0 Slave
Capacity
Options
Press Enter
None
Auto
Manual
Auto Display your
disk drive size
Access Mode
Description
Press Enter to auto-detect the
HDD on this channel. If
detection is successful, it fills the
remaining fields on this menu.
Selecting ‘manual’ lets you set
the remaining fields on this
screen. Selects the type of fixed
disk. "User Type" will let you
select the number of cylinders,
heads, etc.
Note: PRECOMP=65535 means
NONE !
Disk drive capacity
(Approximated). Note that this
size is usually slightly greater
than the size of a formatted disk
given by a disk checking
program.
Choose the access mode for this
hard disk
CHS
LBA
Large
Auto
The following options are selectable only if the ‘IDE Channel 0 Master’ item is
set to ‘Manual’
Cylinder
Min = 0
Set the number of cylinders for
Max = 65535
this hard disk.
Head
Min = 0
Set the number of read/write
Max = 255
heads
Precomp
Min = 0
**** Warning: Setting a value of
Max = 65535
65535 means no hard disk
Landing zone
Min = 0
****
Max = 65535
Sector
Min = 0
Number of sectors per track
Max = 255
48
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
Drive A / Drive B
These fields identify the types of floppy disk drive A or drive B that has
been installed in the computer. The available specifications are:
Non
360KB 1.2MB 720KB 1.44MB 2.88MB
5.25 in. 5.25 in. 3.5 in.
3.5 in.
3.5 in.
Video
This field selects the type of video display card installed in your system.
You can choose the following video display cards:
EGA/VGA
For EGA, VGA, SEGA, SVGA
or PGA monitor adapters. (default)
CGA 40
Power up in 40 column mode.
CGA 80
Power up in 80 column mode.
MONO
For Hercules or MDA adapters.
Halt On
This field determines whether the system will halt if an error is detected
during power up.
All errors
Whenever the BIOS detects a non-fatal error,
the system will stop and you will be prompted.
No errors
The system boot will not be halted for any error
that may be detected. (default)
All, But Keyboard
The system boot will not be halted for a
keyboard error; it will stop for all other errors
All, But Diskette
The system boot will not be halted for a disk
error; it will stop for all other errors.
All, But Disk/Key
The system boot will not be halted for a keyboard or disk error; it will stop for all others.
49
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
Advanced BIOS Features
This section allows you to configure your system for basic operation.
You have the opportunity to select the system’s default speed, boot-up
sequence, keyboard operation, shadowing and security.
Phoenix – AwardBIOS CMOS Setup Utility
Advanced BIOS Features
¾CPU Feature
[Press Enter]
Item Help
¾Hard Disk Boot Priority
[Press Enter]
Virus Warning
[Disabled]
Menu Level
¾
CPU L1 and L2 Cache
[Enabled]
Hyper-Threading Technology
[Enabled]
Allows you to choose the
Quick Power On Self Test
[Enabled]
VIRUS warning feature for
First Boot Device
[Floppy]
IDE Hard Disk boot sector
Second Boot Device
[HDD]
protection. If this function is
Third Boot Device
[LS120]
enabled and someone
Boot Other Device
[Enabled]
attempt to write data into
Swap Floppy Drive
[Disabled]
this area, BIOS will show a
Boot Up Floppy Seek
[Enabled]
warning message on screen
Boot Up NumLock Status
[Off]
and alarm beep
Gate A20 Option
[Fast]
Typematic Rate Setting
[Disabled]
x Typematic Rate (Chars/Sec)
6
x Typematic Delay (Msec)
250
Security Option
[Setup]
x APC Mode
Enabled
MPS Version Control For OS
[1.4]
OS Select For DRAM > 64MB
[Non-OS2]
Report No FDD For Win95
[No]
↑↓←→Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
50
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
Phoenix – AwardBIOS CMOS Setup Utility
Delay Prior Thermal
Thermal Management
Limit CPUID Max Value
CPU Feature
[16Min]
Thermal Monitor 1
[Disabled]
Item Help
Menu Level
¾
↑↓←→Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
Delay Prior Thermal
The choice: 4Min, 8Min, 16Min, 32Min.
Thermal Management
Limit CPUID Max Value
Set Limit CPUID MaxVal to 3, should be [Disabled] for Win XP.
For Windows NT 4.0 operating system, change the default to [Enabled].
51
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
Phoenix – AwardBIOS CMOS Setup Utility
Hard Disk Boot Priority
1.Ch0 M.
:Maxtor 6E040L0
2. Bootable Add-in Cards
Item Help
Menu Level
¾
Use <↑> or <↓> to select a
device, then press <+> to
move it up, or <-> to move
it down the list. Press
<ESC> to exit this menu
↑↓←→Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
Ch0 M.
:Maxtor 6E040L0
Use <↑> or <↓> to select a device, then press <+> to move it up, or <
-> to move it down the list. Press <ESC> to exit this menu.
Virus Warning
Allows you to choose the VIRUS Warning feature for IDE Hard Disk
boot sector protection. If this function is enabled and someone attempt
to write data into this area, BIOS will show a warning message on
screen and alarm beep.
Enabled
Disabled
Activates automatically when the system boots up causing a
warning message to appear when anything attempts to
access the boot sector or hard disk partition table.
No warning message will appear when anything attempts to
access the boot sector or hard disk partition table.
52
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
CPU L1 & L2 Cache
These two categories speed up memory access. However, it depends
on CPU/chipset design.
Enabled
Disabled
Enable cache
Disable cache
Hyper-Threading Technology
This setting allows user to enable or disable Hyper-Threading
technology. If the CPU installed does not support Hyper-Threading
Technlogy, this item will not show up.
The choice: Enabled/Disabled.
Quick Power On Self Test
Allows the system to skip certain tests while booting. This will
decrease the time needed to boot the system.
Enabled
Disabled
Enable quick POST
Normal POST
First/Second/Third/Other Boot Device
The BIOS attempts to load the operating system from the devices in the
sequence selected in these items.
The Choice: Floppy, LS120, ZIP100, HDD, CDROM, LAN, Disabled,
USB-FDD, USB-ZIP, USB-CDROM.
Swap Floppy Drive
If the system has two floppy drives, choose enable to assign physical
drive B to logical drive A and vice-versa.
The choice: Enabled/Disabled.
Boot Up Floppy Seek
Enabled tests floppy drives to determine whether they have 40 or 80
tracks.
The choice: Enabled/Disabled.
53
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
Boot Up NumLock Status
Selects power on state for NumLock.
The choice: On/Off.
Gate A20 Option
Select if chipset or keyboard controller should control GateA20.
Normal
Fast
A pin in the keyboard controller controls GateA20
Lets chipset control GateA20
Typematic Rate Setting
Keystrokes repeat at a rate determined by the keyboard controller.
When enabled, the typematic rate and typematic delay can be selected.
The choice: Enabled/Disabled.
Typematic Rate (Chars/Sec)
Sets the number of times a second to repeat a key stroke when you hold
the key down.
The choice: 6, 8, 10, 12, 15, 20, 24, 30.
Typematic Delay (Msec)
Sets the delay time after the key is held down before it begins to repeat
the keystroke.
The choice: 250, 500, 750, 1000.
Security Option
Select whether the password is required every time the system boots or
only when you enter setup.
System
Setup
The system will not boot and access to Setup will be
denied if the correct password is not entered at the
prompt.
The system will boot, but access to Setup will be
denied if the correct password is not entered at the
prompt.
54
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
Note: To disable security, select PASSWORD SETTING at Main
Menu and then you will be asked to enter password. Do not type
anything and just press <Enter>, it will disable security. Once the
security is disabled, the system will boot and you can enter Setup
freely.
APIC Mode
The choice: Enabled/Disabled.
MPS Version Control For OS
The choice: 1.1, 1.4.
OS Select For DRAM > 64MB
Select the OS2 only if you are running OS/2 operating system with
greater than 64MB of RAM on the system.
The choice: Non-OS2, OS2.
Report No FDD For WIN 95
This option allows Windows 95 to share with other peripherals IRQ6
which is assigned to a floppy disk drive if the drive is not existing. The
default setting is No.
The choice: Yes, No.
55
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
Advanced Chipset Features
Phoenix – AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Timing Selectable
x CAS Latency Time
x Active to Precharge Delay
x DRAM RAS# to CAS# Delay
x DRAM RAS# Precharge
Memory Frequency For
System BIOS Cacheable
Video BIOS Cacheable
Memory Hole At 15M-16M
AGP Aperture Size (MB)
Init Display First
[By SPD]
[3]
[8]
[4]
[4]
[Auto]
[Enabled]
[Disabled]
[Disabled]
[128]
[PCI Slot]
***On-Chip VGA Setting***
On-Chip VGA
On-Chip Frame Buffer Size
[Enabled]
[16MB]
Item Help
Menu Level
¾
↑↓←→Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
This section allows you to configure the system based on the specific
features of the installed chipset. This chipset manages bus speeds and
access to system memory resources, such as DRAM and the external
cache. It also coordinates communications between the conventional
ISA bus and the PCI bus. It must be stated that these items should never
need to be altered. The default settings have been chosen because they
provide the best operating conditions for your system. The only time
you might consider making any changes would be if you discovered
that data was being lost while using your system.
DRAM Settings
The first chipset settings deal with CPU access to dynamic random
access memory (DRAM). The default timings have been carefully
chosen and should only be altered if data is being lost. Such a scenario
might well occur if your system had mixed speed DRAM chips
installed so that greater delays may be required to preserve the integrity
of the data held in the slower memory chips.
56
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
DRAM Timing Selectable
This item allows you to select the DRAM timing determined by the
timing information stored in SPD or set by the User manually. The
default is By SPD. When this field is set as By SPD, the DRAM Timing
items below will become read-only.
The choice: By SPD, Manual.
CAS Latency Time
When synchronous DRAM is installed, the number of clock cycles of
CAS latency depends on the DRAM timing. Do not reset this field
from the default value specified by the system designer.
The choice: 3, 2.5, 2, 1.5.
Active to Precharge Delay
This item allows you to set the Active to Precharge Delay of DRAM
timing. Do not reset this field from the default value specified by the
system designer.
The choice: 8, 7.
DRAM RAS# to CAS# Delay
When DRAM is refreshed, both rows and columns are addressed
separately. This field allows you to determine the timing of transition
from Row Address Strobe (RAS) to Column Address Strobe (CAS).
The choice: 4, 3.
DRAM RAS# Precharge
The precharge time is the number of cycles it takes for the RAS to
accumulate its charge before DRAM refresh. If insufficient time is
allowed, refresh may be incomplete and the DRAM may fail to retain
data.
The choice: 4, 3.
57
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
Memory Frequency For
This item allows user to set the DDR DRAM operation frequency. The
Auto is default.
The choice: DDR266, DDR320, DDR400, Auto.
System BIOS Cacheable
Selecting Enabled allows caching of the system BIOS ROM at
F0000h-FFFFFh, resulting in better system performance. However, if
any program writes to this memory area, a system error may result.
The choice: Enabled, Disabled.
Video BIOS Cacheable
Selecting Enabled allows caching of the Video BIOS ROM, resulting
in better system performance. However, if any program writes to this
memory area, a system error may result.
The choice: Enabled, Disabled.
Memory Hole at 15MB - 16MB
In order to improve performance, certain space in memory can be
reserved for ISA cards. This field allows you to reserve 15MB to 16MB
memory address space to ISA expansion cards. This makes memory
from 15MB and up unavailable to the system. Expansion cards can
only access memory up to 16MB. The default of this field is set to
Disabled.
The choice: Enabled, Disabled.
AGP Aperture Size (MB)
Select the size of Accelerated Graphics Port (AGP) aperture. The
aperture is a portion of the PCI memory address range dedicated for
graphics memory address space. Host cycles that hit the aperture range
are forwarded to the AGP without any translation.
The choice: 4M, 8M, 16M, 32M, 64M, 128M, 256M.
58
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
Init Display First
This item define the Display device scan sequence. If CPI Slot is
selected, System BIOS will scan the PCI display on PCI bus first. If
PCI display card detected, it will become the display device. Otherwise,
BIOS will use integrated graphic device.
The choice: PCI Slot, Onboard/AGP
On-Chip VGA Setting
On-Chip VGA
The choice: Enabled, Disabled.
On-Chip Frame Buffer Size
The choice: 1MB, 8MB, 16MB.
59
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
Integrated Peripherals
Phoenix – AwardBIOS CMOS Setup Utility
Integrated Peripherals
¾OnChip IDE Device
¾Onboard Device
¾SuperIO Device
Onboard Serial Port 3
Serial Port 3 Use IRQ
Onboard Serial Port 4
Serial Port 4 Use IRQ
[Press Enter]
[Press Enter]
[Press Enter]
[3E8]
[IRQ7]
[2E8]
[IRQ7]
Item Help
Menu Level
¾
↑↓←→ Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
Phoenix – AwardBIOS CMOS Setup Utility
OnChip IDE Device
IDE HDD Block Mode
IDE DMA transfer access
On-Chip Primary PCI IDE
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
On-Chip Secondary PCI IDE
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
[Enabled]
[Enabled]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
Item Help
Menu Level
¾
If your IDE hard drive
supports block mode
select Enabled for
automatic detection of
the optimal number of
block read/writes per
sector the drive can
support
***On-Chip Serial ATA Setting***
x SATA Mode
IDE
On-Chip Serial ATA
[Auto]
x Serial ATA Port0 Mode
SATA0 master
Serial ATA Port1 Mode
SATA1 master
↑↓←→ Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
60
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
IDE HDD Block Mode
If your IDE hard drive supports block mode select Enabled for
automatic detection of the optimal number of block read/writes per
sector the drive can support
The choice: Enabled, Disabled.
IDE DMA transfer acess
The choice: Enabled, Disabled.
On-Chip Primary PCI IDE
The chipset contains a PCI IDE interface with support for two IDE
channels. Select Enabled to activate the primary IDE interface. Select
Disabled to deactivate this interface
The choice: Enabled, Disabled.
On-Chip Secondary PCI IDE
The chipset contains a PCI IDE interface with support for two IDE
channels. Select Enabled to activate the secondary IDE interface.
Select Disabled to deactivate this interface
The choice: Enabled, Disabled.
IDE Primary/Secondary Master/Slave PIO
The four IDE PIO (Programmed Input/Output) fields let you set a PIO
mode (0-4) for each of the four IDE devices that the onboard IDE
interface supports. Modes 0 through 4 provide successively increased
performance. In Auto mode, the system automatically determines the
best mode for each device.
The choice: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode 4.
61
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
IDE Primary/Secondary Master/Slave UDMA
Ultra DMA/33/66/100 implementation is possible only if your IDE
hard drive and cable supports it and the operating environment includes
a UDMA driver If your hard drive and your system software both
support Ultra DMA/33/66/100, select Auto to enable BIOS support.
The System BIOS will also check the IDE cable. Only if the 80-way
ATA66/100 cable is installed, the ATA66/100 models can be enabled
by the OS driver. Otherwise, the system will be limited to run up to
ATA33 mode.
The Choice: Auto, Disabled.
On-Chip Serial ATA Setting
SATA Mode
On-Chip Serial ATA
Disabled
Auto
Combined
Mode
Enhanced
Mode
SATA Only
Disabled SATA Controller.
Auto arrange by BIOS.
PATA and SATA are combined. Max. of 2 IDE
drives in each channel.
Enable both SATA and PATA. Max. of 6 IDE
drives are supported.
SATA is operating in legacy mode
Serial ATA Port0 Mode
The choice: Primary Master, Primary Slave, Secondary Master,
Secondary Slave, Primary Master, Secondary Master, SATA0 master,
SATA1 master.
Serial ATA Port1 Mode
The choice: Primary Master, Primary Slave, Secondary Master,
Secondary Slave, Primary Master, Secondary Master, SATA0 master,
SATA1 master.
62
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
Phoenix – AwardBIOS CMOS Setup Utility
Onbord Device
USB Controller
USB 2.0 Controller
USB Keyboard Support
USB Mouse Support
AC97 Audio
[Enabled]
[Enabled]
[Disabled]
[Disabled]
[Auto]
Item Help
Menu Level
¾
↑↓←→ Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
USB Controller
This should be enabled if your system has a USB installed on the
system board and you wish to use it. Even when so equipped, if you add
a higher performance controller, you will need to disable this feature.
The choice: Enabled, Disabled.
USB 2.0 Controller
This entry is for disable/enable EHCI controller only. This BIOS itself
may/may not have high speed USB support. If the BIOS has high speed
USB support built in, the support will be automatically turn on when
high speed device were attached.
The choice: Enabled, Disabled.
USB Keyboard Support
Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have a USB keyboard.
The choice: Enabled, Disabled.
63
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
USB Mouse Support
The choice: Enabled, Disabled.
AC97 Audio
The choice: Auto, Disabled.
64
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
Phoenix – AwardBIOS CMOS Setup Utility
SuperIO Device
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
x RxD , TxD Active
x IR Transmission Delay
x UR2 Duplex Mode
Onboard Parallel Port
Parallel Port Mode
x EPP Mode Select
x ECP Mode Use DMA
PWRON After PWR-Fail
[Enabled]
[3F8/IRQ4]
[2F8/IRQ3]
[Normal]
Hi, Lo
Enabled
Half
[378/IRQ7]
[SPP]
EPP1.7
3
[Off]
Item Help
Menu Level
¾
↑↓←→ Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
Onboard FDC Controller
Select Enabled if your system has a floppy disk controller (FDC)
installed on the system board and you wish to use it. If you install
and-in FDC or the system has no floppy drive, select Disabled in this
field.
The choice: Enabled, Disabled.
Onboard Serial Port 1/Port 2
Select an address and corresponding interrupt for the first and second
serial ports.
The choice: 3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3, Disabled,
Auto.
UART Mode Select
The choice: IrDA, ASKIR, Normal.
RxD, TxD Active
This item allows you to choose Hi-Active or Low-Active of TX and
RX signlal, which depends on different H/W requirement. This field is
65
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
not recommended to change its default setting for avoiding any error in
your system
The Choice: Hi, Hi / Hi, Lo (Default) / Lo, Hi / Lo, Lo.
IR Transmission Delay
This item allows you to Enable/Disable IR tranismission delay.
The choice: Enabled, Disabled.
UR2 Duplex Mode
This item allows you to select the IR half/full duplex function.
The Choice: Half, Full.
Onboard Parallel Port
This item allows you to determine onboard parallel port controller I/O
address setting.
The choice: 378/IRQ7, 278/IRQ5, 3BC/IRQ7, Disabled.
Parallel Port Mode
Select an operating mode for the onboard parallel (printer) port. Select
Normal, Compatible, or SPP unless you are certain your hardware and
software both support one of the other available modes.
The choice: SPP, EPP, ECP, ECP+EPP, Normal.
EPP Mode Select
Select EPP port type 1.7 or 1.9.
The choice: EPP1.7, 1.9.
ECP Mode Use DMA
Select a DMA channel for the parallel port for use during ECP mode.
The choice: 3, 1.
PWRON After PWR-Fail
The choice: Off, On, Former-Sts.
66
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
Onboard Serial Port3/Port4
The choice: Disabled, 4F8, 4E8, 3E8, 2E8.
Serial Port 3 Use IRQ/ Port 4 Use IRQ
The choice: IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10.
67
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
Power Management Setup
The Power Management Setup allows you to configure you system to
most effectively save energy while operating in a manner consistent
with your own style of computer use.
Phoenix – AwardBIOS CMOS Setup Utility
Power Management Setup
Power-Supply Type
ACPI Function
Power Management
Video Off Method
Video Off In Suspend
MODEM Use IRQ
Suspend Mode
HDD Power Down
Soft-Off by PWR-BTTN
CPU THRM-Throttling
Wake-Up by PCI Card
Power On by Ring
Wake Up On LAN
Resume by Alarm
x Date (of Month) Alarm
x Time (hh:mm:ss) Alarm
[ATX]
[Enabled]
[User Define]
[DPMS]
[Yes]
[3]
[Disabled]
[Disabled]
[Instant-Off]
[50.0%]
[Enabled]
[Enabled]
[Enabled]
[Disabled]
0
0: 0 : 0
Item Help
Menu Level ¾
** Reload Global Timer Events **
Primary IDE 0
[Disabled]
Primary IDE 1
[Disabled]
Secondary IDE 0
[Disabled]
Secondary IDE 1
[Disabled]
FDD, COM, LPT Port
[Disabled]
PCI PIRQ[A-D]#
[Disabled]
↑↓←→Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
Power-Supply Type
This should be AT if you use AT power supply or ATX power supply
but force to AT mode. This selection help BIOS provide the
information to OS what kind power-supply the system use. The correct
information provide to OS can avoid the Windows Shutdown issue.
The choice: AT, ATX.
68
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
ACPI Function
This item allows you to enable/disable the Advanced Configuration
and Power Management (ACPI).
The choice: Enabled, Disabled.
Power Management
This category allows you to select the type (or degree) of power saving
and is directly related to the following modes:
1.
HDD Power Down
2.
Suspend Mode
There are three selections for Power Management, three of which have
fixed mode settings.
Disable (default)
Min. Power Saving
Max. Power
Saving
User Defined
No power management. Disables all four modes
Minimum power management. Suspend Mode = 1
hr., and HDD Power Down = 15 min.
Maximum power management. Suspend Mode = 1
min., and HDD Power Down = 1 min.
Allows you to set each mode individually. The
Suspend mode ranges are from 1 min. to 1 hr. The
HDD Power Down ranges are from 1 min. to 15
min. and disable.
Video Off Method
This determines the manner in which the monitor is blanked.
V/H SYNC+Blank
Blank Screen
DPMS
This selection will cause the system to turn off the
vertical and horizontal synchronization ports and
write blanks to the video buffer.
This option only writes blanks to the video buffer.
Initial display power management signaling.
Allows the BIOS to control video display card if
it supports the DPMS feature.
69
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
Video Off In Suspend
This determines the if the turn off the video display when system enter
suspend mode.
The choice: Yes, No.
MODEM Use IRQ
This determines the IRQ in which the MODEM can use.
The choice: 3, 4, 5, 7, 9, 10, 11, NA.
Suspend Mode
When enabled and after the set time of system inactivity, CPU will be
put into the suspend mode.
The choice: Disabled, 1 min, 2 min, 4 min,8min, 12min, 20min, 30min,
40min, 1 hour.
HDD Power Down
When enabled and after the set time of system inactivity, the hard disk
drive will be powered down while all other devices remain active.
The choice: Disabled, 1 min, 2 min, 4 min, ….. 15 min.
Soft-Off by PWR-BTTN
The choice: Instant-Off, Delay 4 Sec.
CPU THRM-Throttling
The choice: 75.0%, 50.0%, 25.0%
Wake-Up by PCI card
The choice: Enabled, Disabled.
70
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
Power On By Ring
An input signal on the serial Ring Indicator (RI) line (in other words, an
ncoming call on the modem) awakens the system from a soft off state.
The choice: Enabled, Disabled.
Wake Up On LAN
The choice: Enabled, Disabled.
Resume by Alarm
When Enabled, your can set the date and time at which the RTC
(real-time clock) alarm awakens the system from Suspend mode.
The choice: Enabled, Disabled.
Reload Global Timer Events
PM events are I/O events whose occurrence can prevent the system
from entering a suspend mode or can awaken the system from such a
mode. In effect, the system remains alert for anything which occurs to
a device which is configured as Enabled, even when the system is in a
Suspend down mode.
Primary/Secondary IDE 0/1
When Enabled, any activity from one of the listed system peripheral
devices or IRQs wakes up the system.
The choice: Enabled, Disabled.
FDD, LPT & COM
When Enabled, any activity from one of the listed system peripheral
devices or IRQs wakes up the system.
The choice: Enabled, Disabled.
PCI PIRQ[A-D]#
When Enabled, any activity from one of the listed PCI IRQ signals
wakes up the system.
The choice: Enabled, Disabled.
71
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
PnP/PCI Configuration Setup
This section describes configuring the PCI bus system. PCI, or
Personal Computer Interconnect, is a system which allows I/O devices
to operate at speeds nearing the speed the CPU itself uses when
communicating with its own special components. This section covers
some very technical items and it is strongly recommended that only
experienced users should make any changes to the default settings.
Phoenix – AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
PnP OS Installed
Reset Configuration Data
[No]
[Disabled]
Item Help
Menu Level
Resources Controlled By
x IRQ Resources
x Memory Resources
[Auto(ESCD)]
Press Enter
Press Enter
¾
Default is Disabled. Select
Enabled to reset Extended
System Configuration
Data(ESCD) when you exit
Setup if you have installed
a new add-on and the
system reconfiguration has
caused such a serious
conflict that the OS cannot
boot
PCI/VGA Palette Snoop
[Disabled]
INT Pin1 Assignment
[Auto]
INT Pin2 Assignment
[Auto]
INT Pin3 Assignment
[Auto]
INT Pin4 Assignment
[Auto]
INT Pin5 Assignment
[Auto]
INT Pin6 Assignment
[Auto]
INT Pin7 Assignment
[Auto]
INT Pin8 Assignment
[Auto]
↑↓←→Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
PNP OS Installed
This item allows you to determine install PnP OS or not.
Yes
No
If you are using a Plug and Play capable operating
system.
If you need the BIOS to configure non-boot
devices.
Reset Configuration Data
Default is Disabled. Select Enabled to reset Extended System
Configuration Data (ESCD) when you exit Setup if you have installed a
new add-on and the system reconfiguration has caused such a serious
conflict that the OS cannot boot.
72
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
The choice: Enabled, Disabled.
Resource controlled by
BIOS can automatically configure all the boot and Plug and Play
compatible devices. If you choose Auto, you cannot select IRQ DMA
and memory base address fields, since BIOS automatically assigns
them.
The choice: Auto(ESCD), Manual.
IRQ Resources
When resources are controlled manually, assign each system interrupt a
type, depending on the type of device using the interrupt. This item
allows you to determine the IRQ assigned to the ISA bus and is not
available to any PCI slot. Legacy ISA for devices compliant with the
original PC AT bus specification, PCI/ISA PnP for devices compliant
with the Plug and Play standard whether designed for PCI or ISA bus
architecture.
The Choice: Legacy ISA and PCI/ISA PnP.
Memory Resources
PCI/VGA Palette Snoop
Leave this field at Disabled.
Choices are Enabled, Disabled.
INT Pin1 Assignment
Device(s) using this INT:
Display Cntrlr- Bus 0 Dev 2 Func 0 USB 1.0/1.1 UHCI Cntrlr
- Bus 0 Dev29 Func 0 USB 1.0/1.1 UHCI Cntrlr
- Bus 0 Dev29 Func3
Choices are Auto, 3, 4, 5, 7, 9, 10, 11, 12, 14, 15.
INT Pin2 Assignment
Device(s) using this INT:
Multimedia Device- Bus 0 Dev31 Func 5 Simple COMM. Cntrlr
- Bus 0 Dev31 Func 6 SMBus Cntrlr
- Bus 0 Dev31 Func 3
Choices are Auto, 3, 4, 5, 7, 9, 10, 11, 12, 14, 15.
73
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
INT Pin3 Assignment
Device(s) using this INT:
Network Cntrlr-Bus 1 Dev 1 Func 0 USB 1.0/1.1UHCI Cntrlr
-Bus 0 Dev29 Func2
Choices are Auto, 3, 4, 5, 7, 9, 10, 11, 12, 14, 15.
INT Pin4 Assignment
Device(s) using this INT:
USB 1.0/1.1 UHCI Cntrlr-Bus 0 Dev29 Func 1
Choices are Auto, 3, 4, 5, 7, 9, 10, 11, 12, 14, 15.
INT Pin5 Assignment
Choices are Auto, 3, 4, 5, 7, 9, 10, 11, 12, 14, 15.
INT Pin6 Assignment
Device(s) using this INT:
Choices are Auto, 3, 4, 5, 7, 9, 10, 11, 12, 14, 15.
INT Pin7 Assignment
Device(s) using this INT:
Nerwork Cntrlr-Bus 2 Dev10 Func 0
Choices are Auto, 3, 4, 5, 7, 9, 10, 11, 12, 14, 15.
INT Pin8 Assignment
Device(s) using this INT:
USB 2.0 EHCI Cntrlr- Bus 0 Dev29 Func 7
Choices are Auto, 3, 4, 5, 7, 9, 10, 11, 12, 14, 15.
74
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
PC Health Status
This section helps you to get more information about your system
including CPU temperature, FAN speed and voltages. It is
recommended that you contact with your motherboard supplier to get
proper value about your setting of the CPU temperature.
Phoenix – AwardBIOS CMOS Setup Utility
PC Health Status
CPU Warning Temperature
[Disabled ]
Item Help
Current CPU Temperature
52°C / 125°F
Current System Temperature
35°C / 95°F
Menu Level ¾
CPU FAN Speed
4500 RPM
System FAN Speed
0 RPM
POWER FAN Speed
0 RPM
Vcore
1.7V
+1.5V
1.5V
+3.3V
3.31V
+5V
5.01V
+12V
12.0V
-12V
-12.03V
-5V
-5.09V
VBAT(V)
3.28V
5VSB(V)
4.95V
Shutdown Temperature
[Disabled]
↑↓←→ Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
CPU Warning Temperature
Select the CPU over-heated warning temperature.
The choice: Disabled, 50°C/122°F, 53°C/127°F, 56°C/133°F, 60°C/140°F,
63°C/145°F, 66°C/151°F, 70°C/158°F.
Current CPU Temperature
Shows CPU Temperatue.
Current System Temperature
Show System Temperature.
CPU FAN Speed
Shows CPU FAN speed.
75
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
System FAN Speed
Shows System FAN speed.
Power FAN Speed
Shows System FAN speed.
Vcore/1.5V/3.3V/5V/12V/-12V/-5V/VBAT/5VSB Voltages
Shows Power rails voltage.
Shutdown Temperature
Select the CPU over-heated shutdown temperature.
The choice: Disabled, 60°C/140°F, 65°C/149°F, 70°C/158°F, 75°C/167°F.
76
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
Frequency/Voltage Control
Phoenix – AwardBIOS CMOS Setup Utility
Frequency/Voltage Control
CPU Clock Ratio
Auto Detect DIMM/PCI Clk
Spread Spectrum
[17X]
[Enabled]
[Enabled]
Item Help
Menu Level ¾
↑↓←→ Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
CPU Clock Ratio
Min=12
Max=17
Key in a DEC number:
Auto Detect DIMM/PCI ClK
This item allows you to enable/disable auto detect PCI Clock. Turning
off the un-used PCI clocks may help to EMI issue. Since there is no PCI
clock routing specification for PICMG backplane, some system may
have PCI card detect issue. In that case, please disable this item.
The choice: Enabled, Disabled.
Spread Spectrum
This item allows you to enable/disable the spread spectrum modulation.
The spread spectrum technology also helps to alleviate the EMI.
The choice: Enabled, Disabled.
77
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
Load Fail-Safe Defaults
When you press <Enter> on this item you get a confirmation dialog box
with a message similar to:
Load Fail-Safe Defaults (Y/N) ? N
Pressing ‘Y’ loads the BIOS default values for the most stable,
minimal-performance system operations.
Load Optimized Defaults
When you press <Enter> on this item you get a confirmation dialog box
with a message similar to:
Load Optimized Defaults (Y/N) ? N
Pressing ‘Y’ loads the default values that are factory settings for
optimal performance system operations.
78
TR-ATX-865G User Manual
Chapter3 BIOS Configuration
Supervisor/User Password Setting
You can set either supervisor or user password, or both of then. The
differences between are:
supervisor password : can enter and change the options of the setup
menus.
user password
: just can only enter but do not have the right to
change the options of the setup menus. When you select this function,
the following message will appear at the center of the screen to assist
you in creating a password.
ENTER PASSWORD:
Type the password, up to eight characters in length, and press <Enter>.
The password typed now will clear any previously entered password
from CMOS memory. You will be asked to confirm the password.
Type the password again and press <Enter>. You may also press
<Esc> to abort the selection and not enter a password.
To disable a password, just press <Enter> when you are prompted to
enter the password. A message will confirm the password will be
disabled. Once the password is disabled, the system will boot and you
can enter Setup freely.
PASSWORD DISABLED.
When a password has been enabled, you will be prompted to enter it
every time you try to enter Setup. This prevents an unauthorized person
from changing any part of your system configuration.
Additionally, when a password is enabled, you can also require the
BIOS to request a password every time your system is rebooted. This
would prevent unauthorized use of your computer.
You determine when the password is required within the BIOS
Features Setup Menu and its Security option. If the Security option is
set to “System”, the password will be required both at boot and at entry
to Setup. If set to “Setup”, prompting only occurs when trying to enter
Setup.
79
TR-ATX-865G User Manual
Chapter 3 BIOS Configuration
Exit Selecting
Save & Exit Setup
Pressing <Enter> on this item asks for confirmation:
Save to CMOS and EXIT (Y/N)? Y
Pressing “Y” stores the selections made in the menus in CMOS – a
special section of memory that stays on after you turn your system off.
The next time you boot your computer, the BIOS configures your
system according to the Setup selections stored in CMOS. After saving
the values the system is restarted again.
Exit Without Saving
Pressing <Enter> on this item asks for confirmation:
Quit without saving (Y/N)? N
This allows you to exit Setup without storing in CMOS any change.
The previous selections remain in effect. This exits the Setup utility
and restarts your computer.
80
TR-ATX-865G User Manual
Appendix
‹
‹
‹
‹
I/O Port Address Map
Interrupt Request Lines (IRQ)
POST Beep
Installation of Windows NT 4.0
81
TR-ATX-865G User Manual
Appendix
A. I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port
addresses which also becomes the identity of the device. There are a
total of 1K port address space available. The following table lists the
I/O port addresses used on the Industrial CPU Card.
Address
000h - 01Fh
020h - 03Fh
040h - 05Fh
060h - 06Fh
070h - 07Fh
080h - 09Fh
0A0h - 0BFh
0C0h - 0DFh
0F0h
0F1h
1F0h - 1F7h
278 - 27F
2F8h - 2FFh
2B0 - 2DF
378h - 3FFh
360 - 36F
3B0 - 3BF
3C0 - 3CF
3D0 - 3DF
3F0h - 3F7h
3F8h - 3FFh
Device Description
DMA Controller #1
Interrupt Controller #1
Timer
Keyboard Controller
Real Time Clock, NMI
DMA Page Register
Interrupt Controller #2
DMA Controller #2
Clear Math Coprocessor Busy Signal
Reset Math Coprocessor
IDE Interface
Parallel Port #2(LPT2)
Serial Port #2(COM2)
Graphics adapter Controller
Parallel Port #1(LPT1)
Network Ports
Monochrome & Printer adapter
EGA adapter
CGA adapter
Floppy Disk Controller
Serial Port #1(COM1)
82
TR-ATX-865G User Manual
Appendix
B. Interrupt Request Lines (IRQ)
There are a total of 15 IRQ lines available on the Industrial CPU
Card. Peripheral devices use interrupt request lines to notify CPU for
the service required. The following table shows the IRQ used by the
devices on the Industrial CPU Card.
Level
IRQ0
IRQ1
IRQ2
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ8
IRQ9
IRQ10
IRQ11
IRQ12
IRQ13
IRQ14
IRQ15
Function
System Timer Output
Keyboard
Interrupt Cascade
Serial Port #2
Serial Port #1
Reserved
Floppy Disk Controller
Parallel Port #1
Real Time Clock
Software Redirected to Int 0Ah
Reserved
Reserved
PS/2 Mouse
80287
Primary IDE
Secondary IDE
83
TR-ATX-865G User Manual
Appendix
C. POST Beep
Currently there are two kinds of beep codes in BIOS. This code
indicates that a video error has occurred and the BIOS cannot
initialize the video screen to display any additional information.
This beep code consists of a single long beep followed by two short
beeps.
The other code indicates that your DRAM error has occurred. This
beep code consists of a single long beep repeatedly.
D. Installation of Windows NT 4.0
Phoenix – AwardBIOS CMOS Setup Utility
CPU Feature
[16Min]
Thermal Monitor 1
[Enabled]
Delay Prior Thermal
Thermal Management
Limit CPUID Max Val
Item Help
Menu Level
¾
↑↓←→Move Enter: Select +/-/PU/PD: Value F10:Save ESC: Exit F1:General Help
F5:Previous Values F6:Fail-safe Defaults
F7:Optimized Defaults
- Highlight the "CPU Feature" option and press the "Enter" key.
- On the "CPU Feature" screen select "Limit CPUID Max Val" setting and
change it to [Enabled].
- Save the BIOS setting and exit by pressing the "F10" key.
(After this change Windows NT 4.0 should successfully install)
84
TR-ATX-865G User Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement