HCD-X1V - Driver Dll service manual user guide

HCD-X1V
SERVICE MANUAL
US Model
Canadian Model
AEP Model
UK Model
Ver. 1.0 2006.07
• HCD-X1V is the amplifier, super audio CD/DVD
system, tuner and video section in DAV-X1V.
This system incorporates with Dolby* Digital
and Dolby Pro Logic (II) adaptive matrix
surround decoder and the DTS** Digital
Surround System.
This system perfectly decodes 5.1 channel
signal, but you cannot add other commercially
available surround speakers.
* Manufactured under license from Dolby
Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
** Manufactured under license from Digital Theater
Systems, Inc. “DTS” and “DTS Digital Surround”
are registered trademarks of Digital Theater
Systems, Inc.
Model Name Using Similar Mechanism
NEW
DVD Mechanism Type
CDM69EH
Optical Pick-up Block Name
KHM-310CAB or
KHM-313CAB
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS
for the US model
POWER OUTPUT AND
TOTAL HARMONIC
DISTORTION
(FTC Output Power):
Front: 38 W/ch 4 ohms at
150 -20,000 Hz,
0.7% THD
Front surround: 38 W/ch
4 ohms at 150 -20,000 Hz,
0.7% THD
Subwoofer: 38 W/ch
4 ohms at 25 - 150 Hz,
0.7 % THD
Amplifier section
Front
Power output (rated):
70 W + 70 W (4 ohms,
1 kHz, 1 % THD)
RMS output power (reference):
80 W + 80 W (4 ohms,
1 kHz, 10 % THD)
Front surround*
Power output (rated):
70 W + 70 W (4 ohms,
1 kHz, 1 % THD)
RMS output power (reference):
80 W + 80 W (4 ohms,
1 kHz, 10 % THD)
Subwoofer
Power output (rated):
70 W + 70 W (4 ohms,
100 Hz, 1 % THD)
RMS output power (reference):
80 W + 80 W (4 ohms,
100 Hz, 10 % THD)
* Depending on the sound field settings and the source,
there may be no sound output.
Inputs (Analog)
VIDEO1, VIDEO2, TV, AUDIO IN
Sensitivity: 450 mV (ATT
ON), 250 mV (ATT OFF)
Impedance: 50 kilohms
Inputs (Digital/COAXIAL)
VIDEO1 , VIDEO2
Impedance: 75 ohms
Super Audio CD/DVD system
Laser
Semiconductor laser
(Super Audio CD/DVD:
λ = 650 nm)
(CD:λ = 790 nm)
Emission duration:
continuous
Signal format system
For North American models:
NTSC
For European models:
NTSC/PAL
Tuner section
System
PLL quartz-locked digital
synthesizer system
FM tuner section
Tuning range
For North American models:
87.5 – 108.0 MHz
(100 kHz step)
For European models:
87.5 – 108.0 MHz
(50 k Hz step)
Antenna (aerial)
FM wire antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
10.7 MHz
– Continued on next page –
SUPER AUDIO CD/DVD RECEIVER
9-887-304-01
2006G05-1
© 2006.07
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
HCD-X1V
AM tuner section
Tuning range
For North American models:
530 – 1,710 kHz (with the
interval set at 10kHz)
531 – 1,710 kHz (with the
interval set at 9 k Hz)
For European models:
531 – 1,602 kHz (with the
interval set at 9 k Hz)
Antenna (aerial)
AM loop antenna (aerial)
Intermediate frequency
450 kHz
Video section
Outputs
VIDEO: 1 Vp-p 75 ohms
S VIDEO:
Y: 1 V p-p 75ohms
C: 0.286 V p-p 75ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
PB/CB, PR/CR: 0.7 V p-p
75 ohms
HDMI OUT: Type A (19
pin)
VIDEO: 1 Vp-p 75 ohms
S VIDEO:
Y: 1 Vp-p 75 ohms
Inputs
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
This appliance is
classified as a CLASS 1
LASER product. This
marking is located on the
rear or bottom exterior.
C: 0.286 V p-p 75 ohms
General
Power requirements
For North American models:
120 V AC, 60 Hz
For European models:
230 V AC, 50 Hz
Power consumption
On: 165 W
Standby: 0.3 W (at the
Power Saving mode)
Dimensions (approx.)
413 × 90 × 325 mm
(16 3/8 × 3 5/8 × 12 7/8
inches) (w/h/d) incl.
projecting parts
Mass (approx.)
5.5 kg (12 lb 3 oz)
Design and specifications are subject to change
without notice.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
To Exposed Metal
Parts on Set
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
0.15 µF
1.5 kΩ
AC
voltmeter
(0.75 V)
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
2
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
HCD-X1V
TABLE OF CONTENTS
SELF DIAGNOSIS FUNCTION
(When letters/numbers appear in the
display)
When the self-diagnosis function is activated to
prevent the system from malfunctioning, a 5character service number (e.g., C 13 50) with a
combination of a letter and 4 digits appears on
the screen and the front panel display. In this
case, check the following table.
C:13:50
First 3
characters of
the service
number
Cause and/or corrective action
C 13
The disc is dirty.
,Clean the disc with a soft cloth.
The disc is not inserted correctly.
,Restart the system, then re-insert
the disc correctly.
C 31
E XX
To prevent a malfunction, the
(xx is a number) system has performed the selfdiagnosis function.
,Contact your nearest Sony
dealer or local authorized Sony
service facility and give the 5character service number.
Example: E 61 10
1.
SERVICING NOTES ............................................... 4
2.
GENERAL ................................................................... 11
3.
DISASSEMBLY
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
3-10.
3-11.
3-12.
3-13.
3-14.
3-15.
3-16.
3-17.
3-18.
3-19.
Disassembly Flow ...........................................................
Top Panel, Side Panel ......................................................
DMB12 Board .................................................................
POWER Board ................................................................
AMP Board ......................................................................
Rear Panel Block .............................................................
MAIN Board ....................................................................
DVD Mechanism deck (CDM69EH) ..............................
Optical Pick-Up Section ..................................................
Optical Pick-Up Block
(KHM-310CAB or KHM-313CAB) ...............................
Bracket (Top) Assy ..........................................................
RELAY Board .................................................................
Motor (Stocker) Assy (Stocker) (M761) .........................
Motor (Stocker) Assy (Roller) (M781) ...........................
Motor (Stocker) Assy (Mode) (M771) ............................
Rubber Roller (Silder) Assy, Sub Chassis .......................
Timing Belt (Front/Rear) .................................................
Cam (Gear) ......................................................................
SENSOR Board, Rotary Encoder (Mode) (S771) ...........
4.
ASSEMBLY
4-1.
4-2.
4-3.
4-4.
4-5.
How To Install The Cam (Eject Lock) ............................
How To Install The Cam (Gear) ......................................
How To Install The Gear (Mode C) .................................
How To Install The Gear (Mode Cam) ............................
How To Install The Rotary Encoder (S702),
Gear (Stocker Communication) .......................................
4-6. How To Install The Cam (Stocker U/D) ..........................
4-7. How To Install The Stocker Assy ....................................
4-8. Phase Adjustment Between Pinions (Slider)
And Slider-1 To 5 (L/R) ..................................................
13
14
14
15
15
16
16
17
17
18
18
19
19
20
20
21
21
22
22
23
23
24
24
25
25
26
27
5.
TEST MODE .............................................................. 28
6.
ELECTRICAL CHECK ........................................... 31
7.
DIAGRAMS
7-1.
7-2.
7-3.
7-4.
7-5.
Block Diagram – RF SERVO/VIDEO Section – ............
Block Diagram – CHANGER/HDMI Section – .............
Block Diagram – AUDIO Section – ................................
Block Diagram – AMP Section – ....................................
Block Diagram
– PANEL/POWER SUPPLY Section – ...........................
Printed Wiring Board – DMB12 Board (Side A) – .........
Printed Wiring Board – DMB12 Board (Side B) – .........
Schematic Diagram – DMB12 Board (1/6) – ..................
Schematic Diagram – DMB12 Board (2/6) – ..................
Schematic Diagram – DMB12 Board (3/6) – ..................
Schematic Diagram – DMB12 Board (4/6) – ..................
Schematic Diagram – DMB12 Board (5/6) – ..................
Schematic Diagram – DMB12 Board (6/6) – ..................
Printed Wiring Boards – CHANGER Section – ..............
Schematic Diagram – CHANGER Section – ..................
Printed Wiring Boards – D-IO/AUDIO IN Boards – ......
Schematic Diagram – D-IO Board – ...............................
Printed Wiring Board
– MAIN Board (Component Side) – ...............................
7-6.
7-7.
7-8.
7-9.
7-10.
7-11.
7-12.
7-13.
7-14.
7-15.
7-16.
7-17.
7-18.
32
33
34
35
36
38
39
40
41
42
43
44
45
46
47
48
49
50
3
HCD-X1V
SECTION 1
SERVICING NOTES
7-19. Printed Wiring Board
– MAIN Board (Conductor Side) – .................................
7-20. Schematic Diagram – MAIN Section (1/6) – ..................
7-21. Schematic Diagram – MAIN Section (2/6) – ..................
7-22. Schematic Diagram – MAIN Section (3/6) – ..................
7-23. Schematic Diagram – MAIN Section (4/6) – ..................
7-24. Schematic Diagram – MAIN Section (5/6) – ..................
7-25. Schematic Diagram – MAIN Section (6/6) – ..................
7-26. Printed Wiring Board
– AMP Board (Component Side) – .................................
7-27. Printed Wiring Board
– AMP Board (Conductor Side) – ...................................
7-28. Schematic Diagram – AMP Board (1/3) – ......................
7-29. Schematic Diagram – AMP Board (2/3) – ......................
7-30. Schematic Diagram – AMP Board (3/3) – ......................
7-31. Schematic Diagram – KEY Section – .............................
7-32. Printed Wiring Board – LED Board – .............................
7-33. Printed Wiring Boards – KEY/POWER-SW Boards – ...
7-34. Printed Wiring Board – DISPLAY Board – ....................
7-35. Schematic Diagram – DISPLAY Board – .......................
7-36. Printed Wiring Board
– POWER Board (Component Side) – ............................
7-37. Printed Wiring Board
– POWER Board (Conductor Side) – ..............................
7-38. Printed Wiring Board – LF Board – ................................
7-39. Schematic Diagram – POWER SUPPLY Section – ........
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
8.
EXPLODED VIEWS
8-1.
8-2.
8-3.
8-4.
8-5.
8-6.
8-7.
8-8.
8-9.
8-10.
Front/Side/Top Panel Section .......................................... 98
MAIN Board Section ....................................................... 99
POWER Board Section .................................................. 100
DVD Mechanism Deck section-1 (CDM69EH) ............. 101
DVD Mechanism Deck section-2 (CDM69EH) ............. 102
DVD Mechanism Deck section-3 (CDM69EH) ............. 103
DVD Mechanism Deck section-4 (CDM69EH) ............. 104
DVD Mechanism Deck section-5 (CDM69EH) ............. 105
DVD Mechanism Deck section-6 (CDM69EH) ............. 106
Optical Pick-Up Section
(KHM-310CAB or KHM-313CAB) .............................. 107
9.
ELECTRICAL PARTS LIST ............................... 108
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
RELEASING THE TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Releasing Procedure :
1. Press the I/1 button to turn on the system.
2. Press the FUNCTION button repeatedly to select “DVD”.
3. While pressing the x button, press the Z button until
“UNLOCKED” displayed on the fluorescent indicator tube
(around 5 seconds).
Note: When “LOCKED” is displayed, the tray lock is not released by turning
power on/off with the I/1 button.
RELEASING THE DEMO PLAY LOCK
Releasing Procedure :
1. Press the I/1 button to turn on the system.
2. Press the FUNCTION button repeatedly to select “DVD”.
3. While pressing the x button, press the N button until
“DEMO OFF” displayed on the fluorescent indicator tube
(around 5 seconds).
Note: When “DEMO PLAY” is displayed, the DEMO play lock is not
released by turning power on/off with the I/1 button.
4
HCD-X1V
NOTE OF REPLACING THE EEPROM (IC103 and
IC706) ON THE DMB12 BOARD
EEPROM (IC103 and IC706) on the DMB12 board cannot exchange
with single. When EEPROM (IC103 and IC706) on the DMB12
board is damaged, exchange the entire mounted board.
NOTE OF HANDLING THE DMB12 BOARD
When the DMB12 board is replaced by a repair for a fee, throw
away the DMB12 board after obtaining consent of not returning of
the DMB12 board to the customer. When throwing away the DMB12
board, be sure to throw away after destroying EEPROM (IC103
and IC706) physically with the hammer etc.
Part No.
A-1212-048-A
A-1212-049-A
S-FORCE FRONT SURROUND OPERATION CHECK
When complaint by the effect of the sound field, check as follows
and confirm abnormality is not found in the set.
Procedure:
1
Press [/1.
The system turns on.
Unless the system is set to “DVD,” press
FUNCTION +/– to select “DVD.”
2
3
4
Press DISC 1.
Press Z.
Load the Setup Disc.
Push the disc into the disc slot until the disc
is pulled in automatically.
The Setup Disc is drawn into the system
automatically.
Destination
US, Canadian
AEP, UK
With the playback side facing down
MODEL IDENTIFICATION
– Back Panel –
PART No.
MODEL
US model
Canadian model
AEP and UK models
PART No.
2-647-349-0[]
2-647-349-1[]
2-647-349-2[]
The Setup Disc menu appears.
DAV-X1 Series
This setup disc is common for DAV-X1 series.
5
Sit in the listening position, then select
one of the three options on the screen
using C/c, and press H or
.
The selected option starts.
FL
RL
6
C
SW
FR
RR
Listening carefully to how the option
sounds to determine the optimal
surround sound effect.
If a satisfactory surround sound effect
cannot be achieved, adjust the speaker
positions.
7
8
Press x to stop the disc.
Press Z on the system to eject the
disc.
5
HCD-X1V
About This Manual
• The instructions in this manual describe the
controls on the remote. You can also use the
controls on the system if they have the same or
similar names as those on the remote.
• The Control Menu items may be different
depending on the area.
• “DVD” may be used as a general term for
DVD VIDEOs, DVD+RWs/DVD+Rs, and
DVD-RWs/DVD-Rs.
• Measurements are expressed in feet (ft) for
North American models.
• The following symbols are used in this
manual.
Symbol
Meaning
Functions available for DVD
VIDEOs, DVD-Rs/DVD-RWs in
video mode, and DVD+Rs/
DVD+RWs
Functions available for DVD-Rs/
DVD-RWs in VR (Video
Recording) mode
Functions available for VIDEO
CDs (including Super VCDs or CDRs/CD-RWs in video CD format or
Super VCD format)
Functions available for Super Audio
CDs
Functions available for music CDs
or CD-Rs/CD-RWs in music CD
format
Functions available for DATA CDs
(CD-ROMs/CD-Rs/CD-RWs)
containing MP31) audio tracks,
JPEG image files, and DivX2)3)4)
video files
Functions available for DATA
DVDs (DVD-ROMs/DVD-Rs/
DVD-RWs/DVD+Rs/DVD+RWs)
containing MP31) audio tracks,
JPEG image files, and DivX2)3)4)
video files
1)
“DVD+RW,” “DVD-RW,” “DVD+R,”
“DVD VIDEO,” and the “CD” logos are trademarks.
Note about CDs/DVDs
The system can play CD-ROMs/CD-Rs/CDRWs recorded in the following formats:
– audio CD format
– video CD format
– MP3 audio tracks, JPEG image files, and
DivX video files* of format conforming to
ISO 9660 Level 1/Level 2, or its extended
format, Joliet
The system can play DVD-ROMs/DVD+RWs/
DVD-RWs/DVD+Rs/DVD-Rs recorded in the
following formats:
– MP3 audio tracks, JPEG image files and
DivX video files* of format conforming to
UDF (Universal Disc Format)
* European models only
Example of discs that the
system cannot play
The system cannot play the following discs:
• CD-ROMs/CD-Rs/CD-RWs other than those
recorded in the formats.
• CD-ROMs recorded in PHOTO CD format
• Data part of CD-Extras
• DVD Audios
• DATA DVDs that do not contain MP3 audio
tracks, JPEG image files, or DivX video files*
* European models only
MP3 (MPEG1 Audio Layer 3) is a standard format
defined by ISO/MPEG which compresses audio data.
2)European
models only.
3) DivX®
is a video file compression technology,
developed by DivX, Inc.
4)
CD-RW/CD-R
(audio data)
(MP3 files)
(JPEG files)
DivX, DivX Certified, and associated logos are
trademarks of DivX, Inc. and are used under license.
This System Can Play the
Following Discs
Format of
discs
DVD VIDEO
DVD-RW/
DVD-R
DVD+RW/
DVD+R
Super Audio
CD
(except for a
multi-channel
playback area)
VIDEO CD
(Ver. 1.1 and
2.0 discs)/
Audio CD
6
Disc logo
Music discs encoded with
copyright protection
technologies
This product is designed to play back discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
Note on DualDisc
A DualDisc is a two sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
About Multi Session CD
• This system can play Multi Session CDs when
an MP3 audio track is contained in the first
session. Any subsequent MP3 audio tracks
recorded in later sessions can also be played
back.
• This system can play Multi Session CDs when
a JPEG image file is contained in the first
session. Any subsequent JPEG image files
recorded in later sessions can also be played
back.
• If audio tracks and images in music CD format
or video CD format are recorded in the first
session, only the first session will be played
back.
Region code
• DVD-RAMs
Also, the system cannot play the following
discs:
• A DVD VIDEO with a different region code
• A disc that has a non-standard shape (e.g.,
card, heart)
• A disc with paper or stickers on it
• A disc that has the adhesive of cellophane tape
or a sticker still left on it
Notes about CD-R/CD-RW/DVD-R/
DVD-RW/DVD+R/DVD+RW
In some cases, CD-R/CD-RW/DVD-R/DVDRW/DVD+R/DVD+RW cannot be played on
this system due to the recording quality or
physical condition of the disc, or the
characteristics of the recording device and
authoring software.
The disc will not play if it has not been correctly
finalized. For more information, see the
operating instructions for the recording device.
Note that some playback functions may not
work with some DVD+Rs/DVD+RWs, even if
they have been correctly finalized. In this case,
view the disc by normal playback. Also some
DATA CDs/DATA DVDs created in Packet
Write format cannot be played.
Your system has a region code printed on the
rear of the unit and will only play DVDs labeled
with the same region code.
DVD VIDEOs labeled ALL will also play on this
system.
If you try to play any other DVD VIDEO, the
message [Playback prohibited by area
limitations.] will appear on the TV screen.
Depending on the DVD VIDEO, no region code
indication may be given even though playing the
DVD VIDEO is prohibited by area restrictions.
Note on playback operations
of DVDs and VIDEO CDs
Some playback operations of DVDs and VIDEO
CDs may be intentionally set by software
producers. Since this system plays DVDs and
VIDEO CDs according to the disc contents the
software producers designed, some playback
features may not be available. Also, refer to the
instructions supplied with the DVDs or VIDEO
CDs.
HCD-X1V
HOW TO IDENTIFY OPTICAL PICK-UP BLOCK
There are two kinds of OPTICAL PICK-UP BLOCK in this set.
When replacing the OPTICAL PICK-UP BLOCK, make sure which OPTICAL PICK-UP BLOCK it is following the “How to Identify” in
the figure shown below.
Printed of KHM-310CAB or KHM-313CAB.
KHM-310CAB
or
KHM-313CAB
DMB12 BOARD SERVICE POSITION
Please place a sheet
for insulation.
DMB12 board
(side B)
DMB12 board
(side A)
7
HCD-X1V
POWER BOARD SERVICE POSITION
Please place a sheet
for insulation.
POWER board
Note: The Power board can be removed individually.
NOTE ON WIRE PROCESSING BETWEEN AMP BOARD AND POWER BOARD
Note: To prevent a contact with the components on the primary side of power supply,
the wires should be routed in front of the wire (flat type) (19 core) and reshaped.
wire (flat type) (19 core)
wire
POWER board
8
AMP board
HCD-X1V
MAIN BOARD SERVICE POSITION
1 wire (flat type) (9 core)
(US, Canadian models)
wire (flat type) (11 core)
(AEP, UK models)
(CN303)
3 Remove the Back Panel,
and then the MAIN board.
4
2 connector
(CN1000)
Please place a sheet
for insulation.
MAIN board
AMP BOARD SERVICE POSITION
AMP board
(component side)
AMP board
(conductor side)
Please place a sheet
for insulation.
9
HCD-X1V
DVD MECHANISM DECK (CDM69EH) SERVICE POSITION
In checking the DVD mechanism deck (CDM69EH), prepare jig (extension cable J-2501-248-A: 1.00 mm Pitch, 27 cores, Length 300
mm).
DVD mechanism deck
(CDM69EH)
wire (flat type) (27 core)
MAIN board
(CN621)
connect jig (extension cable J-2501-248-A)
to the MAIN board (CN621) and
wire (flat type) (27 core).
PRECAUTION WHEN INSTALLING A NEW OPTICAL PICK-UP BLOCK/
PRECAUTION BEFORE UNSOLDERING THE STATIC ELECTRICITY
PREVENTION SOLDER BRIDGE
CAUTION
When installing a new Optical Pick-up block, be sure to connect
the flexible printed circuit board first of all before removing the static
electricity prevention solder bridge by unsoldering. Remove the static
electricity prevention solder bridge by unsoldering after the flexible
printed circuit board has already been connected.
(Do not remove nor unsolder the solder bridge as long as the Optical Pick-up block is kept
standalone.)
flexible flat cable (24 core)
optical pick-up block
10
HCD-X1V
SECTION 2
GENERAL
This section is extracted from
instruction manual.
Front panel
A "/1 (on/standby)
H Front surround indicator
B Disc slot
I Front panel display
C
J Z (eject)
(remote sensor)
D N (play)
K DISC 1-5/indicator
E x (stop)
L AUDIO IN jack
F FUNCTION
G VOLUME –/+
Rear panel
HDMI
OUT
COMPONENT
VIDEO
OUT Y
VIDEO1
VIDEO1 VIDEO2
S VIDEO
L
VIDEO
R
VIDEO2
TV
A.CAL
MIC
ECM-AC1
PB/CB
PR/CR
MONITOR
OUT
VIDEO IN
OPTICAL
ANTENNA
AM
AUDIO IN
OPTICAL
COAXIAL
COAXIAL
FM
TV
IMPEDANCE USE 4
VIDEO1
A HDMI OUT jack
I A.CAL MIC jack
B COMPONENT VIDEO OUT jacks
J AM terminal
C MONITOR OUT (S VIDEO/VIDEO) jacks
D VIDEO1 (VIDEO IN, S VIDEO/VIDEO)
jacks
K FM 75Ω COAXIAL jack
E VIDEO2 (VIDEO IN, S VIDEO/VIDEO)
jacks
F VIDEO1 (AUDIO IN L/R) jacks
G VIDEO2 (AUDIO IN L/R) jacks
VIDEO2
75
COAXIAL
DIGITAL IN
SPEAKER
L VIDEO2 (DIGITAL IN COAXIAL) jack
M VIDEO1 (DIGITAL IN COAXIAL/
OPTICAL) jacks
N TV (DIGITAL IN OPTICAL) jack
O SPEAKER jacks
H TV (AUDIO IN L/R) jacks
11
HCD-X1V
Front panel display
About the indications in the front panel display
A Lights up when the sleep timer is set.
H Displays system’s status such as
chapter, title, or track number, time
information, radio frequency, playing
status, sound field, etc.
B Current surround format (Except for
JPEG and Super Audio CD)
C Playing status (DVD function only)
I Lights up when the system outputs
progressive signals (DVD function
only).
D Lights up when the time information of
a title or chapter appears in the front
panel display. (DVD only)
J Lights up when the HDMI OUT jack is
correctly connected to HDCP (highbandwidth digital content protection)
compliant device with HDMI or DVI
(digital visual interface) input.
E Lights up when a station is received.
(Radio only)
F Monaural/Stereo effect (Radio only)
G Lights up when the music or movie
mode is selected.
K Lights up when Super Audio CD/CD is
loaded.
Remote control
N m/M
/
TUNING –/+
O DISC SKIP
P VOLUME +/–
TV VOL +/–3)
Q MUTING
R AUDIO2)
S PICTURE NAVI
T PROGRESSIVE
U DIMMER
V FM MODE
W DIRECT TUNING
X [/1 (on/standby)
Y THEATRE SYNC
Z TV/VIDEO
wj ENTER1)3)
wk BASS/TREBLE
wl DVD MENU
TOOLS3)
e;
DISPLAY
TV MENU3)
ea H (play)2)
es x (stop)
ed X (pause)
With the cover opened.
A TV [/1 (on/standby)
B TV button/TV mode indicator
C SLEEP
eg SUBTITLE
eh ANGLE
ej SA-CD/CD
ek REPEAT
D DISPLAY
E Number buttons
ef FUNCTION +/–2)
TV CH +/–3)
2)3)
F CLEAR
-/--3)
G MOVIE/MUSIC
H SOUND FIELD
el AMP MENU
r; TUNER MENU
1)
The ENTER button is the same function as the
button.
2)The
H ea, 5 5, AUDIO qk, and FUNCTION +/
– ef buttons have tactile dots. Use the tactile dots as
references when operating the system.
I DVD TOP MENU
J C/X/x/c/
K O RETURN3)
L ./>
PRESET –/+
M
12
(instant replay/instant
advance)
c/C STEP
3)
These buttons change to the TV operation buttons
when the remote is in TV mode. The remote is in TV
mode when the TV mode indicator 2 lights up by
pressing the TV button 2.
HCD-X1V
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Note 1: The process described in
can be performed in any order.
Note 2: Without completing the process described in
, the next process can not be performed.
SET
3-2. TOP PANEL, SIDE PANEL
(Page 14)
3-3. DMB12 BOARD
(Page 14)
3-4. POWER BOARD
(Page 15)
3-6. REAR PANEL BLOCK
(Page 16)
3-5. AMP BOARD
(Page 15)
3-7. MAIN BOARD
(Page 16)
3-8 . DVD MECHANISM DECK
(CDM69EH)
(Page 17)
3-9. OPTICAL PICK-UP SECTION
(Page 17)
3-13. MOTOR (STOCKER)
ASSY (STOCKER) (M761)
(Page 19)
3-11. BRACKET (TOP) ASSY
(Page 18)
3-12.RELAY BOARD
(Page 19)
3-14. MOTOR (STOCKER)
ASSY (ROLLER) (M781)
(Page 20)
3-16. RUBBER ROLLER
(SLIDER) ASSY,
SUB CHASSIS
(Page 21)
3-15. MOTOR (STOCKER)
ASSY (MODE) (M771)
(Page 20)
3-17. TIMING BELT
(FRONT/REAR)
(Page 21)
3-18. CAM (GEAR)
(Page 22)
3-10. OPTICAL PICK-UP BLOCK
(KHM-310CAB or KHM-313CAB)
(Page 18)
3-19. SENSOR BOARD,
ROTARY ENCODER (MODE) (S771)
(Page 22)
13
HCD-X1V
Note: Follow the disassembly procedure in the numerical order given.
3-2. TOP PANEL, SIDE PANEL
8 top panel
1 two screws
(BVTT3 × 8)
5 connector
(CN804)
2 side panel (L)
7 three screws
(BV/ring)
6 screw
(BV/ring)
3 two screws
(BVTT3 × 8)
6 screw
(BV/ring)
4 side panel (R)
3-3. DMB12 BOARD
1 cushion (FFC)
6 two connectors
(CN201, CN601)
2 wire (flat type) (11 core)
(CN4301)
8 four screws
(BVTT3 × 6)
8 screw
(BVTT3 × 6)
3 wire (flat type) (24 core)
(CN101)
4 wire (flat type) (11 core)
(CN4501)
9 shield plate (DMB)
7 three screws
(BV/ring)
5 wire (flat type) (11 core)
(CN109)
8 three screws
(BVTT3 × 6)
q; DMB12 board
14
HCD-X1V
3-4. POWER BOARD
1 three connectors
(CN902, CN903,
CN904)
2 four screws
(BVTT3 × 6)
3 screws
(BVTT3 × 8)
4 cover (L)
5 POWER board
1 connector
(CN905)
3-5. AMP BOARD
6 two screws
(BV3)
2 two screws
(BVTT3 × 6)
4 bracket (DMB)
7 heart sink
8 screw (BV3)
A
qa AMP board
1 wire (flat type) (19 core)
(CN621)
3 two screws (BV/ring)
q; two accessory screws
9 two screws
(BV/ring)
A
5 two connectors
(CN902, CN903)
15
HCD-X1V
3-6. REAR PANEL BLOCK
7 bracket (DMB)
5 two screws
(BVTT3 × 6)
8 three screws
(BVTT3 × 6)
q; two screws
(BV/ring)
2 wire (flat type) (27 core)
(CN621)
qd two bosses
A
3 wire (flat type) (19 core)
(CN507)
4 two connectors
(CN401, CN506)
6 two screws (BV/ring)
qs two screws
(BV/ring)
9 screw
(BVTT3 × 6)
qa two accessory
screws
qd boss
A
qf back plate
block
qd two bosses
1 wire (flat type) (19 core)
(CN501)
9 screw
(BVTT3 × 6)
4 two connectors
(CN901, CN3000)
9 three screws
(BVTT3 × 6)
3-7. MAIN BOARD
4 MAIN board
1 wire (flat type) (9 core)
(US, Canadian models)
wire (flat type) (11 core)
(AEP, UK models)
(CN303)
3 six screws
(BV/ring)
2 connector (CN1000)
16
HCD-X1V
3-8. DVD MECHANISM DECK (CDM69EH)
7 DVD mechanism deck
(CDM69EH)
3 screw
(BVTT3 × 6)
6 four screws
(BV3)
2 bar
4 two screws
(BV3)
5 cover (CDM)
1 two screws
(BVTP3 × 8)
4 screw
(BV3)
1 two screws
(BVTP3 × 8)
3-9. OPTICAL PICK-UP SECTION
1 floating screw (PTPWH M2.6)
2 boss
5 boss
3 boss
6 optical pick-up section
4 boss
17
HCD-X1V
3-10. OPTICAL PICK-UP BLOCK (KHM-310CAB or KHM-313CAB)
2 insulator screw
5 optical pick-up block
(KHM-310CAB or
KHM-313CAB)
4 insulator
1 flexible flat cable (24 core)
2 insulator screw
2 insulator screw
4 insulator
4 insulator
2 insulator screw
4 insulator
3
3-11. BRACKET (TOP) ASSY
4 Lift up the SW (3) board.
3 Lift up the SW (2) board.
1 four screws
(BTP2.6 × 6)
2 Lift up the SW (1) board.
18
5 Lift up the SW (4) board.
6 six screws
(BVTP2.6)
7 bracket (top) assy
HCD-X1V
3-12. RELAY BOARD
3
– bottom view –
4 connector
(CN702)
1 Remove thirteen solders of
CN704, CN705, CN706,
CN707, CN708.
CN705
CN704
4 connector
(CN703)
4 connector
(CN710)
CN707
CN706
CN708
2 four screws
(BVTP2.6)
5 RELAY board
RELAY board
1 Remove five solders of
rotary encoder (stocker position) (S702).
3-13. MOTOR (STOCKER) ASSY (STOCKER) (M761)
3 two screws
(BVTP2.6)
4
2 Remove two solders of
motor (stocker) assy (stocker) (M761).
2 Remove two solders of connector (CN761).
5 stocker motor board
6 motor (stocker) assy
(stocker) (M761)
1 belt (stocker)
19
HCD-X1V
3-14. MOTOR (STOCKER) ASSY (ROLLER) (M781)
3 two screws
(BVTP2.6)
2 Remove two solders of
motor (roller) assy (roller) (M781).
4 ROLLER MOTOR board
2 Remove two solders of connector (CN781).
5 motor (roller) assy
(roller) (M781)
1 belt (roller V)
3-15. MOTOR (STOCKER) ASSY (MODE) (M771)
2 Remove seven solders of
connector (CN771).
MODE MOTOR board
2 Remove five solders of
rotary encoder (mode) (S771).
3 two screws
(BVTP2.6)
4 MODE MOTOR board
5 motor (stocker) assy
(mode) (M771)
2 Remove two solders of
motor (stocker) assy (mode) (M771).
1 belt (mode V)
20
HCD-X1V
3-16. RUBBER ROLLER (SLIDER) ASSY, SUB CHASSIS
5 step screw
8 step screw
0 rubber roller
(slider 4) assy
9 tension
spring
(slider 2)
1 step screw
7 rubber roller
(slider 1) assy
6 tension spring
(slider 4)
qa rubber roller
(slider 2) assy
2 rubber roller
(slider S) assy
bracket (top) assy
qs step screw
qd rubber roller
(slider 1) assy
3 tension spring
(base slider 5)
qf screw
(BVTP2.6 × 8)
4 rubber roller
(slider 5) assy
qg sub chassis
3-17. TIMING BELT (FRONT/REAR)
3 slider (mode cam) assy
7 two gears (center)
8 timing belt (rear)
5 two gears
(center)
When install three timing belts,
its pass under each claws.
timing belt
(rear)
9 timing belt (rear)
claw
6 timing belt
(front)
timing belt
(rear)
claw
claw
claw
4 gear
(timing)
timing belt (front)
2 gear (mode cam)
Note: Refer to assembly (Section 4).
1 screw
(PTPWH2.6 × 8)
21
HCD-X1V
3-18. CAM (GEAR)
qf cam (gear)
Note: Refer to assembly
(Section 4: page 23).
6 gear (mode 5)
qd screw
5 screw (PTPWH2.6 × 8)
4 gear (mode 5)
qs gear (mode cam)
Note: Refer to assembly
(Section 4: page 24).
3 screw (PTPWH2.6 × 8)
qa screw
(PTPWH2.6 × 8)
2 pulley
(mode deceleration)
0 gear (mode C)
Note: Refer to assembly
(Section 4: page 24).
9 screw
(PTPWH2.6 × 8)
1 screw (PTPWH2.6 × 8)
8 gear (mode D)
7 screw (PTPWH2.6 × 8)
3-19. SENSOR BOARD, ROTARY ENCODER (MODE) (S771)
Note: Refer to assembly
(Section 4: page 23).
qa cam (eject lock)
q; screw
(PTPWH2.6 × 8)
ql two claws
w; rotary encoder
(mode) (S771)
qf gear (eject lock)
qg gear (mode A)
qd cam (BU U/D)
6 shaft
(shutter)
5 compression spring
(shutter)
7 Remove three solders
of connector (CN751).
1 screw
(PTPWH2.6 × 8)
22
qj gear (mode B)
9 SENSOR board
8 screw
(BVTP2.6 × 8)
4 base (shutter) block
qs screw
(PTPWH2.6 × 8) 3 screw
(BVTP2.6 × 8)
qk screw
(PWH2 × 6)
3 two screws
(BVTP2.6 × 8)
2 lever shutter (A)
qh screw
(PTPWH2.6 × 8)
HCD-X1V
SECTION 4
ASSEMBLY
• This set can be assembled in the order shown below.
4-1.
HOW TO INSTALL THE CAM (EJECT LOCK)
1 Rotate the cam (BU U/D) fully in the direction of arrow.
2 Engage the gear (eject lock) and the gear of the cam (eject lock)
aligning the mark with the center of the gear (eject lock).
cam (BU U/D)
mark
gear (eject lock)
cam (eject lock)
– bottom view • front –
4-2.
HOW TO INSTALL THE CAM (GEAR)
1 Check that the cam (BU U/D) can not be rotated in the direction of arrow.
2 Align the mark on the cam (gear) with the boss as shown in the figure
and install the cam (gear).
cam (gear)
boss
cam (BU U/D)
mark
– bottom view • front –
23
HCD-X1V
4-3.
HOW TO INSTALL THE GEAR (MODE C)
1 Align the mark on the rotary encoder (S771) with the projection of the assy.
2 Check that the cam (BU U/D) can not be rotated in the direction of arrow.
3 Install the gear (mode C).
rotary encoder
(S771)
cam (BU U/D)
gear (mode C)
mark
chassis
projection
– bottom view • front –
4-4.
HOW TO INSTALL THE GEAR (MODE CAM)
1 Slide the shaft in the direction of arrow.
2 Align mark A on the gear (mode cam) with mark B on the slider (mode cam) assy,
then install the gear (mode cam).
3 Check that mark C on the gear (mode cam) is in alignment with mark D on the cam (gear).
shaft
mark A
slider (mode cam) assy
gear (mode cam)
mark D
mark B
mark C
cam (gear)
– bottom view • front –
24
HCD-X1V
4-5.
HOW TO INSTALL THE ROTARY ENCODER (S702), GEAR (STOCKER COMMUNICATION)
4 gear
(stocker communication)
5 screw
(PTPWH2.6 × 8)
3 screw
(PWH2 × 6)
Engage the rotary encoder (S702)
and the gear (stocker communication)
as shown below in the figure.
7 two screws
(PTPWH2.6 × 8)
1 rotary encoder
(S702)
6 two gears
(stocker communication)
rotary encoder
(S702)
2 five solders
gear
(stocker
communication)
ST ENCODER board
– rear –
4-6.
RELAY board
HOW TO INSTALL THE CAM (STOCKER U/D)
1 Position the hole on the gear
(stocker communication) on the
screw of the rotary encoder (S702).
rotary encoder
(S702)
hole
screw
gear
(stocker communication)
– rear –
3 screw
(PTPWH2.6 × 8)
3 two screws
(PTPWH2.6 × 8)
2 cam (stocker U/D)
cam (stocker U/D)
f mark
cam (stocker U/D)
f mark
2 two cams
(stocker U/D)
f mark
cam (stocker U/D)
To install three cams (stocker U/D), align each groove
of the cam (stocker U/D) with each f mark on the
chassis as shown in the figure.
25
HCD-X1V
4-7.
HOW TO INSTALL THE STOCKER ASSY
1 Fit three shafts of the stocker assy in respective slits
of the cams (stocker U/D).
Note: For the location of slits of the cams (stocker U/D),
see 4-6. HOW TO INSTALL CAM (STOCKER U/D).
cam (stocker U/D)
cam (stocker U/D)
shaft
stocker assy
shaft
cam (stocker U/D)
cam (stocker U/D)
cam (stocker U/D)
shaft
stocker assy
pulley (stocker)
pulley (stocker)
A
2 Making sure that three shafts of the stocker assy fit in
respective slits of the cams (stocker U/D), rotate the
pulley (stocker) in the direction of arrow A by hand to
store the stocker assy.
26
HCD-X1V
4-8.
PHASE ADJUSTMENT BETWEEN PINIONS (SLIDER) AND SLIDER-1 TO 5 (L/R)
1 As shown in the following figure, adjust the portion A of each slider to the boss with the
slider-1 to 5 (L) and the slider-1 to 5 (R) pushed in the arrow directions respectively (see Fig. 1).
2 Paying attention to the up/down direction of the pinion (slider) (see Fig. 2), install each pinion (slider)
so that the portion B of each pinion (slider) meshes with the portion A of each slider (see Fig. 3).
Note: Push in the pinion (slider) until the claw of the boss comes out above the pinion (slider) to lock.
A
boss
pinion (slider)
A
A
boss
pinion (slider)
A
slider-5 (R)
A
slider-5 (L)
boss
A
pinion (slider)
slider-4 (L)
slider-4 (R)
slider-3 (L)
slider-3 (R)
slider-2 (L)
slider-2 (R)
slider-1 (L)
A
slider-1 (R)
boss
(Fig. 1)
pinion (slider)
A
boss
claw
A
pinion (slider)
boss
pinion (slider)
A
(Fig. 2)
boss
pinion (slider) portion B
pinion (slider) portion B
slider portion A
slider portion A
claw
(Fig. 3)
27
HCD-X1V
SECTION 5
TEST MODE
AM STEP CHANGE (US and Canadian models)
The step interval of AM channels can be toggled between 9 kHz
and 10 kHz.
Procedure:
1. Press the I/1 button to turn on the system.
2. Press the [FUNCTION] button repeatedly to select the “TUNER
AM”.
3. Press the I/1 button to turn off the system.
4. Press two buttons of [FUNCTION] and I/1 simultaneously. The
system will turn on automatically. The message “AM 9k
STEP” or “AM10k STEP” appears on the fluorescent indicator
tube and thus the channel step is changed.
DVD VERSION VIEW
This mode is used to display the DVD version.
Procedure:
1. Press the I/1 button to turn on the system.
2. Press the [FUNCTION] button repeatedly to select the “DVD”.
3. Press the I/1 button to turn off the system.
4. Press two buttons of x and I/1 simultaneously. The system
will turn on automatically.
5. The DVD version appears on the TV screen.
COLD RESET
The cold reset clears all data including preset data stored in the
RAM to initial conditions.
Procedure:
1. Press the I/1 button to turn on the system.
2. Press three buttons of x , [FUNCTION] and I/1 simultaneously.
3. The message “COLD RESET” appears on the fluorescent
indicator tube, then becomes standby mode.
SHIP MODE
This mode moves the optical pick-up to the position durable to
vibration.
Procedure:
1. Press the I/1 button to turn on the system.
2. Press the [FUNCTION] button repeatedly to select the “DVD”.
3. Press three buttons of x , Z and I/1 simultaneously.
4. After the “STANDBY” blinking display finishes, the message
“MECHA LOCK” appears on the fluorescent indicator tube
and the ship mode is set.
PANEL TEST MODE
This mode is used to check the fluorescent indicator tube, LEDs,
keys, model, destination and software version.
Procedure:
1. Press three buttons of x , N and [DISC 3] simultaneously.
2. LEDs (amber) and all segments in fluorescent indicator tube
are lighted up. And half LEDs (green) and segments in
fluorescent indicator tube are lighted up, all LEDs and others
half segments in fluorescent indicator tube are lighted up, then
LEDs (amber) and all segments in fluorescent indicator tube
are lighted up. This operation is repeated.
3. Press the N button, the key check mode is activated.
4. In the key check mode, the fluorescent indicator tube displays
“K 0”. Each time a button is pressed, “K 0” value increases.
However, once a button has been pressed, it is no longer taken
into account.
5. When you want to enter the software version display mode,
press the [VOLUME +] button. The model information appears
on the fluorescent indicator tube.
28
6. Each time the [VOLUME +] button is pressed, the display
changes from destination information, MC version, GC
version, SYS version, DVD version, CDMA version, CDMB
version, ST version, TC version, TA version, DVD version,
TM version in this order, and returns to the model information
display.
7. When the [VOLUME --] button is pressed while the version
numbers are being displayed except model information and
destination information, the date of the software creation
appears. When the [VOLUME --] button is pressed again, the
display returns to the software version display. When the
[VOLUME +] button is pressed while the date of the software
creation is being displayed, the date of the software creation
is displayed in the same order of software version display.
8. To release from this mode, press three buttons in the same
manner as step 1 or disconnect the power cord.
AMP TEST MODE
Procedure:
1. Press three buttons of x , N and Z simultaneously. The
message “MEASURE” appears on the fluorescent indicator
tube.
2. Press the [SLEEP] button on the remote commander. The
message “SAFETY” appears on the fluorescent indicator tube.
3. Press the [SLEEP] button on the remote commander again.
The message “MEASURE” appears on the fluorescent
indicator tube.
4. Press the [SOUND FIELD] button on the remote commander.
The message “SWAP FULL” appears on the fluorescent
indicator tube.
5. Each time the [SOUND FIELD] button is pressed, the display
changes from SWAP THRU, SWAP F2S, SWAP F2CW in
this order, and returns to “SWAP FULL” .
6. Press the [BASS/TREBLE] button on the remote commander.
The message “D.C.A.C. MIC” appears on the fluorescent
indicator tube.
7. Press the [BASS/TREBLE] button on the remote commander
again. The message “FUNC INPUT” appears on the
fluorescent indicator tube.
8. Press two buttons of [VOLUME +] and [VOLUME --] simultaneously.
The message “VOL N” (volume normal operation) or “VOL
M/M” (volume MIN/MAX operation) appears on the
fluorescent indicator tube and thus the volume step is changed.
9. When the [VOLUME --] button is pressed in the volume MIN/
MAX operation state, the message “VOLUME MIN” appears
on the fluorescent indicator tube.
10. When the [VOLUME +] button is pressed in the volume MIN/
MAX operation state, the message “VOLUME MAX” appears
on the fluorescent indicator tube.
11. To release from this mode, press I/1 button to execute the
COLD RESET.
PRODUCT OUT
This mode moves the optical pick-up to the position durable to
vibration and clears all data including preset data stored in the RAM
to initial conditions.
Procedure:
1. Press the I/1 button to turn on the system.
2. Press the [FUNCTION] button repeatedly to select the “DVD”.
3. Press three buttons of x , [DISC 3] and [VOLUME +]
simultaneously.
4. After the “STANDBY” blinking display finishes, The message
“MECHA LOCK” appears on the fluorescent indicator tube
and the ship mode is set.
HCD-X1V
DVD SECTION
1. DVD SERVICE MODE GENERAL DESCRIPTION
This mode let you make diagnosis and adjustment easily by using
the remote commander and the TV screen. The instructions,
diagnostic results, etc. are given on the on-screen display.
2. ENTERING DVD SERVICE MODE
Procedure:
1. Press the I/1 button to turn on the system.
2. Press the [FUNCTION] button repeatedly to select the “DVD”.
3. Press three buttons of x , Z and [VOLUME +] simultaneously.
4. The message “SERVICE IN” appears on the fluorescent
indicator tube and top menu of the Remocon Diagnosis Menu
appears on the on-screen display on the TV screen as follows.
The model name, IF-con version and Syscon version are
displayed at the bottom of the on-screen display.
Remocon Diagnosis Menu
0.
1.
2.
3.
4.
External Chip Check
Servo Parameter Check
Drive Manual Operation
Emergency History
Version Information
Model Name :XZ1_xx
IF-con:Ver.xx.xx(xxxx)
Syscon:Ver.x.xxx
5. To execute each function, press its number by using numeric
button on the remote commander.
6. To release from this mode, press the I/1 button to turn off the
system.
3. EXECUTING IOP MEASUREMENT
In order to execute IOP measurement, the following standard
procedures must be followed.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “2
Drive Manual Operation” by pressing the [2] button on the
remote commander. The following screen appears on the onscreen display
Drive Manual Operation
1.
2.
3.
4.
5.
0.
Servo Control
Track/Layer Jump
Manual Adjustment
Mecha test mode
MIRR time Adjust
Return to Top Menu
2. Select “3. Manual Adjustment” by pressing the [3] button on
the remote commander. The following screen appears on the
on-screen display.
Manual Adjust
Track Balance Adjust:
Track Gain Adjust:
Focus Balance Adjust:
Focus Gain Adjust:
Eq boost Adjust:
Iop:
TRV. Level:
S curve(FE) Level:
RFL(PI) Level:
MIRR Time:
V v
Change Value
[RETURN]Return to previous menu
1.
2.
3.
4.
5.
6.
7.
8.
9.
0.
3. Select “6. Iop:” by pressing [6] button on the remote
commander.
4. Wait until a hexadecimal number appear in the on-screen
display as below.
Manual Adjust
Track Balance Adjust:
Track Gain Adjust:
Focus Balance Adjust:
Focus Gain Adjust:
Eq boost Adjust:
Iop: ED:
TRV. Level:
S curve(FE) Level:
RFL(PI) Level:
MIRR Time:
V v
Change Value
[RETURN]Return to previous menu
1.
2.
3.
4.
5.
6.
7.
8.
9.
0.
5. Convert data from hexadecimal to decimal by using conversion
table.
6. If the value is smaller than 93 (decimal), then it is OK. However
if the value is higher than 93, then BU (base unit) is defective
and need to be change.
7. Press the O RETURN button on the remote commander to
return to previous menu.
8. Press the [0] button on the remote commander to return to the
top menu of Remocon Diagnosis Menu.
9. Press the I/1 button to turn off the system.
4. CHECKING EMERGENCY HISTORY
To check the emergency history, please follow the following
procedure.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “3.
Emergency History” by pressing the [3] button on the remote
commander. The following screen appears on the on-screen
display.
Emg. History Check
Laser Hours
CD
999h 59min
DVD
999h 59min
01. 01 05 04 04
00 00 00 00
00 92 46 00
00 00 23 45
02. 02 02 01 01
00 00 00 00
00 A9 4B 00
00 00 23 45
[Next]Next page [Prev]Prev page
[0]Return to Top Menu
29
HCD-X1V
2. You can check the total time when the laser is turned on during
playback of DVD and CD from the above menu. The maximum
time, which can be displayed are 999h 59min.
3. You can check the error code of latest 10 emergency history
from the above menu. To view the previous or next page of
emergency history, press the . or > button on the
remote commander. The error code consists of three kinds of
error codes.
A. Error code
To Clear the Laser Hour
Press the [ DISPLAY] button on the remote commander and then
press the [CLEAR] button on the remote commander. The data for
both CD and DVD data are reset.
Emg. History Check
Laser Hours
CD
0h
DVD
0h
0min
0min
01. 01 05 04 04
00 00 00 00
00 92 46 00
00 00 23 45
02. 02 02 01 01
00 00 00 00
00 A9 4B 00
00 00 23 45
Example of Error code
01. 01 05 04 04
00 00 00 00
00 92 46 00
00 00 23 45
The meaning of error code is as below:
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mechanical move error (5 changer)
26: Mechanical move stack error
30: DC motor adjustment error
31: DPD offset adjustment error
32: TE balance adjustment error
33. TE sensor adjustment error
34. TE loop gain adjustment error
35. FE loop gain adjustment error
36. Bad jitter after adjustment
40. Focus NG
42. Focus layer jump NG
51: Spindle stop error
52. Open kick spindle error
60: Focus on error
61: Seek fail error
62: Read Q data/ID error
70: Lead in data read fail
71: TOC read time out (CD)
80: Can’t buffering
81: Unknown media type
B. Parameter of error code
This is the detail of error code.
Example of Error code
01. 01 05 04 04
00 00 00 00
00 92 46 00
00 00 23 45
[Next]Next page [Prev]Prev page
[0]Return to Top Menu
To Clear the Emergency History
Press the [DVD TOP MENU] button on the remote commander and
then press the [CLEAR] button on the remote commander. The error
code for all emergency history would be reset.
Emg. History Check
Laser Hours
CD
999h 59min
DVD
999h 59min
01. 00 00 00 00
00 00 00 00
00 00 00 00
00 00 00 00
02. 00 00 00 00
00 00 00 00
00 00 00 00
00 00 00 00
[Next]Next page [Prev]Prev page
[0]Return to Top Menu
To Execute the Initialize Setup Data
Procedure:
1. Press the [DVD MENU] button on the remote commander and
then press the [CLEAR] button on the remote commander. The
following screen appears on the on-screen display.
Emg. History Check
Laser Hours
CD
999h 59min
DVD
999h 59min
Initialize setup data...
C. Time of error code
This is the laser time when an error occurred.
Example of Error code
01. 01 05 04 04
00 00 00 00
00 92 46 00
00 00 23 45
[Next]Next page [Prev]Prev page
[0]Return to Top Menu
2. The screen after a while returns to former display.
To Return to the Top Menu of Remocon Diagnosis
Menu
Press the [0] button on the remote commander.
30
HCD-X1V
SECTION 6
ELECTRICAL CHECK
5. CHECKING VERSION INFORMATION
DVD SECTION
To check the version information, please follow the following
procedure.
Procedure:
1. From the top menu of Remocon Diagnosis Menu, select “4.
Version Information” by pressing the [4] button on the remote
commander. The following screen appears on the on-screen
display.
RFMON LEVEL CHECK
Connection :
oscilloscope
DMB12 board
CN105 pin 6 (RFMON)
CN105 pin 3 (GND)
Version information
Firm(Main): Ver. X.XXXX
Firm(Sub): XX.XX
RISC: XXXXXX
8032: XXXXXX
Audio DSP: XX.XX.XX.XX
SubCPU: Ver.X.XX(XXXX)
+
–
Procedure :
1. Connect an oscilloscope to CN105 pin 6 (RFMON) and
CN105 pin 3 (GND) on the DMB12 board.
2. Press the I/1 button to turn on the system.
3. Insert the test disc (DVD-SL (NTSC): HLX-503 (Part No. J6090-069-A, CD: YEDS-18 (Part No. 3-702-101-01) and press
the N button to playback.
4. Confirm that oscilloscope waveform is clear and check
RFMON signal level is correct or not.
[0]Return to Top Menu
Note:
A clear RFMON signal waveform means that the shape “◊” can be
clearly distinguished at the center of the waveform.
2. To return to the top menu of Remocon Diagnosis Menu, press
the [0] on the remote commander.
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
level:
0.58 ± 1.23 Vp-p
(DVD-SL)
0.57 ± 1.1 Vp-p
(CD)
Connecting Location:
– DMB12 Board (Side A) –
CN105
6
1
IC201
IC101
HCD-X1V
31
31
HCD-X1V
SECTION 7
DIAGRAMS
7-1. BLOCK DIAGRAM – RF SERVO/VIDEO Section –
(Page 34)
SPDIF
SPDIF 225
2
3
4
5
DVDA
DVDB
DVDC
DVDD
D2
ASDATA1 218
BUFFER
IC4501
ASDATA4 222
29 V2O
PD
20 MDI1
21 MDI2
BCK
LRCK
23 LDO1
YUV0
SMPTE_Y (0) 177
SMPTE_Y (1) 176
SMPTE_Y (2) 174
22 LDO2
S VIDEO
2 4
V2
YUV7
VCLK
HSYNC
VSYNC
C1
C2
SMSDI
SMSDO
SMSCK
XSMCS
209
210
208
211
C2
48 MSW
VIDEO AMP, 75Ω DRIVER
IC203
Y2
4 CIN
1 VIN1
3 VIN2
5 VIN3
YUV1 194
FOCUS/TRACKING COIL DRIVE,
SPINDLE/SLED MOTOR DRIVE
IC201
VOUT 7
8 YIN
11 SYIN
YUV4 200
42 FOO
TRK+
TRK–
35
34
TRACKING
COIL DRIVE
4
41 TRO
SL+
SL–
29
30
SLED
MOTOR DRIVE
10
38 FMO
SP+
SP–
27
28
SPINDLE
MOTOR DRIVE
13
46
47
BUFFER
45
15 CRIN
SD-RAM
IC104
37 DMO
DQ0 – DQ15
A0 – A11
2, 4, 5, 7, 8, 10, 11, 13, 42,
44, 45, 47, 48, 50, 51, 53
23 – 26,
29 – 34, 22, 35
20 21
38 37
15 39 18 17 19 16
183 MUTE
181 TSD_M
HD0 – HD7
229
103 102 51
81 – 84,
86 – 88, 91
HA0 – HA21
93, 78, 53 – 59, 75, 74,
72 – 67, 92, 60, 61, 76, 89
Y
J200
PB/CB
COMPONENT
VIDEO OUT
PR/CR
: VIDEO
WIDE 179
:Y
77 79 66
101 98 99
100 114 110 105
: CHROMA
: COMPONENT VIDEO
XRST
SWITCHING
IC150
29, 31, 33, 35,
38, 40, 42, 44
45, 25 – 18, 8 – 1,
48, 17, 16, 9, 10
26 28 11
31 32 33
37 34
38
DQ0 – DQ7
A-1, A0 – A20
EEPROM
IC103
FLASH ROM
IC102
HCD-X1V
32
32
D
(Page 33)
5 6 7
MTK RST
X101
27MHz
DVD XIFCS
DVD_XIFBUSY
OSC BUFFER
IC111
TX27M
(Page 33)
5 14
143 145 156 157 113 137 140 139 142 138
DVD_SID
DVD_SOD
DVD_SCO
8
2
XSYSRST
XRST
RA0 – RA11
XIFCS
XIF5SY
RD0 – RD15
IFSOI
IFSDO
IFSCK
40 IOPMON
147, 149 – 151, 166 – 164,
162, 160, 159, 146, 158
DQM0
DQM1
RAS
CAS
RCS
RWE
40
125 – 123, 121, 120, 118, 117,
115, 135, 133 – 128, 126
DRCLK
CKE
184 MUTE123
S VIDEO
: DVD PLAY
BA0
BA1
19
21
20
22
Y
: AUDIO
CE
OE
WE
REGULATOR
24
23
21
20
18
17
47 SPFG
SDA
SCL
WF
A
31
32
CYOUTA
CYOUTB
CBOUTA
CBOUTB
CROUTA
CROUTB
C
: CD PLAY
RF+3.3V
REGO2
REGO1
32
31
27
26
J201
MONITOR
OUT
• SIGNAL PATH
XROMCS
XRD
XWR
BUFFER
YUV6 203
SDA
SCL
EEWP
41
13 CBIN
XTALI
MUTE12
MUTE5
MUTE34
TSD-M
YUV5 202
LDQM
UDQM
RAS
CAS
CS
WE
1
CLK
CLKE
FOCUS
COIL DRIVE
BA0
BA1
36
37
C OUT
S-DC OUT
YOUTA
YOUTB
VIDEO
2 4
RF AMP, SERVO DSP,
MPEG DECODER
IC101
FCS+
FCS–
VOUTA 30
VOUTB 29
VIDEO SELECTOR
IC200
YUV2 196
136 LINYSW
LIMIT
Y
VOUT 7
2 4
Y1
J202
VIDEO1
S VIDEO
3 VIN2
5 VIN3
YUV3 198
C
1 VIN1
6 CVBSIN
DVD ON
SWITCH
Q101-2
VIDEO
Y2
VIDEO SELECTOR
IC201
MUTE1
MUTE2
VR (650)
5 VIN3
J203
VIDEO2
Y
VOUT 7
S1
VR (780)
Q103
CD ON
SWITCH
Q101-1
3 VIN2
YUV6
VCLK 178
SMBSY 207
VSYN 205
SMSDI
SMSDO
SMSCK
XSMCS
C1
1 VIN1
C
YUV5
SMPTE_Y (7) 168
MSW
V2
VIDEO
Y1
56 55 54 53
SYSTEM CONTROLLER
IC501 (1/5)
V_SEL0
V_SEL1
V_SEL2
V_SEL3
LD (650)
V1
YUV2
YUV4
SMPTE_Y (4) 171
SMPTE_Y (6) 169
OPTICAL PICK-UP
BLOCK
KHM-310CAB
OR
KHM-313CAB
YUV1
YUV3
SMPTE_Y (5) 170
AUTOMATIC POWER
CONTROL (FOR DVD)
Q102-2
V1
VIDEO SELECTOR
IC202
SW1
SW2
LD (780)
MCK
BUFFER
IC4502
ACLK 215
SMPTE_Y (3) 172
AUTOMATIC POWER
CONTROL (FOR CD)
Q102-1
C
(Page 33)
ABCK 214
ALRCK 213
18 TNI
19 TPI
VC
HDMI BUS
D3
ASDATA2 219
SW1
SW2
MA
MB
MC
MD
ABCK
ALRCK
ACLK
VOE/E+G
VOF/F+H
8
9
10
11
SPDIF
ASDATA0
ASDATA1
ASDATA2
ASDATA4
VOA/A
VOB/B
VOC/C
VOD/D
B
D1
ASDATA0 217
SW1
SW2
6 DVDRFIP
RF
DIGITAL AUDIO BUS
HCD-X1V
7-2. BLOCK DIAGRAM – CHANGER/HDMI Section –
ROLLER MOTOR DRIVE
IC711
CHANGER CONTROLLER1
IC621
• SIGNAL PATH
: AUDIO
M781
(ROLLER)
M
4 OUT1
2 OUT2
FIN 7
RIN 9
24 P0
23 P1
: VIDEO
MODE MOTOR DRIVE
IC701
M771
(MODE)
M
4 OUT1
2 OUT2
FIN 7
RIN 9
22 P2
21 P3
STOCKER MOTOR DRIVE
IC721
M761
(STOCKER)
M
4 OUT1
2 OUT2
FIN 7
RIN 9
20 P4
19 P5
CN701
HDMI OUT
HDMI TRANSMITTER
IC701
DISC INSERT
DETECT SENSOR
IC751
LEVEL SHIFT
Q731
ASDATA0
6 P14
ASDATA1
ASDATA2
OFF: When disc out from
play position
S715
S714
ON: Play position
(8cm disc only)
S713 (ON: Play position)
SPDIF
10 P10
ACLK
ABCK
ALRCK
S716 (STOCKER IN/OUT)
CHANGER CONTROLLER2
IC622
9 P11
75 AD1
TX0N 51
TMDS DATA0 +
9
TMDS DATA0 –
4
74 AD2
TX1P 55
73 AD3
TX1N 54
72 SPDIF
TX2P 58
TMDS DATA1 +
6
TMDS DATA1 –
1
77 ACL
78 ABCK
79 ALRCK
YUV0
13 Y0
YUV1
S715 (DISC OUT)
11 P9
S714 (DISC IN (8cm))
ROTARY
ENCODER
S771
TMDS DATA2 +
8 P12
S713 (DISC IN (8/12cm))
IO_DI
IO_CLK
IO_CE
IO_RESET
87
89
85
86
26
3
4
2
DI1
CLK
LATCH
RESET_B
DO2
DO1
CLKO
LATCHO
25
15
14
13
16
26
3
4
2
DI2
DI1
CLK
LATCH
RESET_B
HTPLG 40
18 Y5
YUV6
19 Y6
YUV7
SW+9V
20 Y7
VCLK
HSYNC
VSYNC
DO2 25
TMDS CLOCK –
TCKN 48
17 Y4
YUV5
S711 (DISC INSERT (8/12cm))
35 CDM_OPEN_SW
TMDS CLOCK +
12
16 Y3
YUV4
(STOCKER POSITION)
10
TCKP 49
15 Y2
YUV3
ROTARY
ENCODER
S702
TMDS DATA2 –
TX2N 57
14 Y1
YUV2
(MODE)
7 P13
S711 (ON: When disc insert)
TX0P 52
3
S717 (DISC POSITION)
5–8
OFF: The moment disc in/out
from stocker
12 P8
P15 – P12
S716
ASDATA4
9 – 12
In the midst disc is moving
between play position and stocker
S717
ON: disc is play position side,
OFF: disc is stocker side
S718 (STOCKING)
P11 – P8
S718
OFF: In the midst disc is moving
between play position and
stocker
7
76 AD0
LEVEL SHIFT
IC705
19
LEVEL SHIFT
Q701
16
LEVEL SHIFT
Q702
15
+5V
REGULATOR
IC707
18
HOT
SDA
SCL
+5V POWER
11 VCK
39 HSYNC
38 VSYNC
EEPROM
IC706
TX27M
CLK 26
A
MSD
MSCK
SSO
SSCK
TRAP2
INT
RST
IO-DO 88
SDA
SCL
WP
(Page 32)
5 6 7
35 34 22 21 31 27 25
SYSTEM CONTROLLER
IC501 (2/5)
41 40
14
15
HDMI CONTROLLER
IC708
58
P35/AN05
62 63 61 24 59
X1
SDO
SDI
SCK
XSMCS
VSYNC
X0
31
30
32
23
22
SDA0
SCL0
50 49 51
SMSDI
SMSDI
SMSCK
XSMCS
VSYNC
SDA
SCK
TRAP2
XTXINT
XTXRST
(Page 32)
HDCP-SDA
HDCP-SCL
HDCP-WP
C
X701
10MHz
HDMI BUS
XRST 21
XRST
D
(Page 32)
HCD-X1V
33
33
HCD-X1V
7-3. BLOCK DIAGRAM – AUDIO Section –
L
15 X2
LINE AMP
IC360
X 13
TV
R
11 X3
R-CH
L
AUDIO IN
R-CH
12 X0
L
DIGITAL AUDIO SELECTOR
IC1004
10 9
VIDEO2
R
R-CH
Q396
TV
OPTICAL
OPTICAL
RECEIVER
IC1000
VIDEO1
OPTICAL
OPTICAL
RECEIVER
IC1001
AUDIO SELECTOR
IC351
J401
A.CAL MIC
ECM-AC1
R-CH
MIC AMP
IC401
12 X0
X 13
4 DIN1 (I)
DATA (O) 16
(Page 35)
82 DPSIE
DPSOA 64
78 DPSIA
DPSOB 65
DPSOC 70
15 D4
ASDATA0
DIGITAL IN
14 X1
BCK (O) 14
VIDEO1
COAXIAL
A B
10 9
VIDEO2
COAXIAL
Q305
ABCK
LRCK (O) 15
4 D0
WAVE
SHAPER
IC1003
ALRCK
2
3
5
6
11
10
1A
1B
2A
2B
3A
3B
SWITCHING
IC771
3 D1
14 D5
11 10 9
SW+3.3V
Q397
SPDIF
OPTICAL
COAXIAL
DATA SELECTOR
IC704
X701
12.288MHz
DO (O)
DI (I)
CL (I)
CE (I)
CSFLAG (O)
ERROR (O)
XSTATE (O)
XMODE (I)
S1000
DIGITAL INPUT
SELECTOR
(Page 32)
ACLK
XIN (I) 22
XOUT (O) 21
1Y 4
79 DPSIB
2Y 7
89 DPBCK
DPDVBCK 87
3Y 9
88 DPLRCK
DPDVLRCK 86
D1
AMP BUS
E
D2
D3
BCK
LRCK
MCK
CKOUT (O) 13
A B C
14 4A
13 4B
4Y 12
94 DPFSCK
A/B
1
ASDATA1
80 DPSIC
ASDATA2
81 DPSID
35 36 38 37 25 34 17 48
DIGITAL AUDIO BUS
127 MOSI
125 SPICLK
16 DIR_ERR
X501
5MHz
66 5 7 68 19 27 67 69
18
SYSTEM CONTROLLER
IC501 (3/5)
42 RDS_DATA
75 RDS_CLK
RDS-DATA
RDS-CLOCK
(AEP, UK)
70
DSP_MISO
DSP_INTR
DSP_SPIDS
DSP_RESET
6
3
71
72
126
15
122
121
MISO
INT_REQ
SPIDS∗
RESET∗
XTAL
ST_DI
ST_DO
ST_CLK
ST_CE
TUNED
13
142
143
X1
25MHz
HCD-X1V
34
34
F
(Page 35)
SEL_SA-CD
44
47
45
48
43
DIN
DO
CLK
CE
TUNED
15
DIR_ZERO
AM ANT
100 MIC/A.CAL SW
59 MIC_SW2
DIR_HDOUT
DSP_MOSI/DIR_DIN
DSP_SPICLK/DIR_CLK
DIR_HCE
DIR_CSFLAG
DIR_ERR
DIR_XSTATE
DIR_RST
50 58 51 52 49
R-CH
XOUT
AM
FM ANT L-CH
R-CH
XIN
FM 75Ω
COAXIAL
DIR_XSTATE
TUNER (FM/AM)
A_SEL2
A_SEL4
A_SEL1
A_SEL0
A_SEL3
ANTENNA
CLKIN
B
DSP
IC2
97 NOUAUDIO∗
J1000
R-CH
: MIC INPUT
3 DIN0 (I)
Q395
15 X2
J801
AUDIO IN
: DIGITAL AUDIO IN
AUDIO (O) 24
Y 5
2 D2
13 D6
16 AINR
6 BCLK
3 LRCLK
1 MCLK
DIGITAL AUDIO INTERFACE RECEIVER
IC702
MUTING CONTROL
SWITCH
Q304
A B
: TUNER (FM/AM)
DOUT 2
R-CH
R-CH
VIDEO1
: AUDIO
19 AINL
MUTING
Q302
14 X1
R
• R-ch is omitted due to same as L-ch.
• SIGNAL PATH
A/D CONVERTER
IC701
AUDIO SELECTOR
IC350
J201
HCD-X1V
7-4. BLOCK DIAGRAM – AMP Section –
• SIGNAL PATH
D FLIP-FLOP
IC706
CLK
2
(Page 34)
E
AMP BUS
: AUDIO
D 1
4 Q
DATA1
MCK1
BCK
LRCK
SWITCHING
IC705
F
DIR_XSTATE
9
8
(Page 34)
BUFFER
IC3500
10
Q701
D1
D2
D3
BCK
LRCK
MCK
13
12
4
5
1
2
11
9
11
6
8
12
3
7
13
6
5
4
3
2
14
15
16
17
18
DATA1
DATA2
SCDT
SHIFT
LAT1
INIT
SOFTMUTE
OVF1
DATA3
31
36
30
29
DATA
XFSIIN
BCK
LRCK
21
22
23
27
19
24
25
OUTR2 4
SCDT
SCSHIFT
XFSOIN 48
SCLATCH
INIT
FSOCKO 37
SOFTMUTE
FSOI 38
OVFFLAGR
FLAGLOVF XFSOOUT 14
CN3500
SPEAKER
DIGITAL POWER AMP
IC3150
STREAM PROCESSOR
IC3010
LRCK
OUTL1 11
6 PWM_A
OUT_A
28 – 30
L.P.F.
OUTL2 9
14 PWM_B
OUT_B
25 – 27
L.P.F.
/RESET /SD
5
4
OUTR1 6
SCDT
SHIFT
LAT3
INIT
SOFTMUTE
OVF2
21
22
23
27
19
24
SCDT
SCSHIFT
SCLATCH
INIT
SOFTMUTE
OVFFLAGR
14 PWM_B
OUT_B
25 – 27
L.P.F.
6 PWM_A
OUT_A
28 – 30
L.P.F.
OUTL1 11
14 PWM_B
6 PWM_A
OUTL2 9
OUT_B
OUT_A
25 – 27
SCDT
SHIFT
LAT2
INIT
SOFTMUTE
OVF1
SYSTEM CONTROLLER
IC501 (4/5)
DAMP_SCDT
DAMP_SHIFT
DAMP LATCH1
DAMP LATCH2
DAMP LATCH3
DAMP INIT
DAMP SOFT MUTE
OVERFLOW1
OVERFLOW2
21
22
23
27
19
24
25
SCDT
SCSHIFT
SCLATCH
INIT
SOFTMUTE
OVFFLAGR
FLAGLOVF
14
12
28 – 30
SW+
L.P.F.
5
SW–
L.P.F.
/RESET /SD
5
4
7
OVER LOAD
DETECT
Q3271, 3272
XFSOIN 48
DIGITAL POWER AMP
IC3200
FSOI 38
14 PWM_B
OUT_B
25 – 27
L.P.F.
6 PWM_A
OUT_A
28 – 30
L.P.F.
SW+
SW–
9
11
OVER LOAD
DETECT
Q3221, 3222
DIGITAL POWER AMP
IC3350
STREAM PROCESSOR
IC3030
DATA
XFSIIN
BCK
LRCK
FRONT RCH–
OVER LOAD
DETECT
Q3121, 3122
/RESET /SD
5
4
31
36
30
29
FRONT RCH+
DIGITAL POWER AMP
IC3250
XFSOOUT 14
DATA2
MCK2
BCK
LRCK
15
DIGITAL POWER AMP
IC3100
X3051
49.152MHz
STREAM PROCESSOR
IC3020
DATA
XFSIIN
BCK
LRCK
13
OVER LOAD
DETECT
Q3171, 3172
/RESET /SD
5
4
31
36
30
29
FRONT LCH–
OSC BUFFER
IC3051
BCK
LRCK
MCK2
MCK1
MCK3
DATA3
MCK3
BCK
LRCK
FRONT LCH+
OUTL1 11
6 PWM_A
OUT_A
28 – 30
L.P.F.
OUTL2 9
14 PWM_B
OUT_B
25 – 27
L.P.F.
/RESET /SD
5
4
OUTR1 6
OUTR2 4
REAR LCH+
4
REAR LCH–
2
OVER LOAD
DETECT
Q3371, 3372
XFSOIN 48
DIGITAL POWER AMP
IC3300
FSOI 38
SCDT
1
SHIFT
2
LAT1
78
LAT2
79
LAT3
80
INIT
76
SOFTMUTE
77
OVF1
83
OVF2
84
14 PWM_B
OUT_B
25 – 27
L.P.F.
6 PWM_A
OUT_A
28 – 30
L.P.F.
/RESET /SD
5
4
REAR RCH+
1
REAR RCH–
OVER LOAD
DETECT
Q3301, 3302
3
D3351
FAN MOTOR
DRIVE
Q3001, 3002
DRIVE_RST (EN) 81
DRIVE_OCP (DIAG) 82
PROTECT DETECT
Q3351
HCD-X1V
35
35
M+13V
B+ SWITCH
(FOR FAN MOTOR)
Q3000
M
M3000
(FAN)
HCD-X1V
7-5. BLOCK DIAGRAM – PANEL/POWER SUPPLY Section –
+9V
REGULATOR
IC300
A+9V
A+12V, M+12V
+12V
REGULATOR
IC507
RECT
D941
M+9V
+9V
REGULATOR
IC507
RECT
D944
3 – 39
40 – 49
GRID DRIVE
Q802
G1 – G10
FL801
FLUORESCENT
INDICATOR
TUBE
AD1, AD2,
S1 – S35
FLUORESCENT INDICATOR
TUBE DRIVER
IC803
50 G11
OSC0 58
OSC1 59
OSC
C809, R814
DAT
CLK
CS
RST
63
62
61
60
24
21
25
11
T801
INVERTER
TRANSFORMER
FL_D_OUT/LED_DATA
FL_CLK/LED_CLK
FL_CS/STB
FL_RESET
FOR FLUORESCENT
INDICATOR TUBE
FL
FL
VFL
RECT
D801,802,804, 805
OSC
Q801
LED DRIVER
IC802
(AMBER)
15 Q9
(GRN)
14 Q8
D811
DISC 1
DATA 3
CLK 4
LCK 5
+3.3V
REGULATOR
IC502
PANEL+3.3V
13 Q7
(GRN)
12 Q6
+5V
REGULATOR
IC506
22 LED_LAT
RIPPLE
FILTER
Q504
SW+5V
(AMBER)
T902
SUB POWER
TRANSFORMER
M+13V
SERVO DSP+3.3V
+3.3V
REGULATOR
IC105
RF+3.3V
+3.3V
REGULATOR
IC107
D812
DISC 2
POWER CONTROL
IC901
T901
MAIN POWER
TRANSFORMER
D906, 907
1 OCP/SYNC
D905
(AMBER)
11 Q6
(GRN)
10 Q4
HDMI+3.3V
D813
DISC 3
(AMBER)
(AMBER)
+32V
LED+6V
B+ SWITCH
(FOR LED)
Q501, 502
A+5V
+5V
REGULATOR
IC504
SYSTEM CONTROLLER
IC501 (5/5)
8 Q2
7 Q1
DSP+1.2V
3 D
RECT
D942
LED DRIVE
Q817
D818
LED DRIVE
Q818
WIDE
SUR
D819
LED DRIVE
Q819
2CH
STEREO
REMOTE CONTROL
RECEIVER
IC801
SW+2.6V
+2.6V
REGULATOR
IC703
SW+3.3V
+3.3V
REGULATOR
IC505
28 LED2
SERVO DSPI+1.8V
36 LED3
4 SIRCS_IN
D922
97, 95, 94
ISOLATOR
PC901
5 FB/OLP
RIPPLE FILTER
Q921
4 VCC
HDMI+1.8V
+1.8V
REGULATOR
IC702
AMP+1.8V
+1.8V
REGULATOR
IC3050
SHUNT
REGULATOR
IC951
D502
E+3.3V
AC_CUT 20
SYSTEM+3.3V
RESET
SWITCH
Q503
1 DRAIN
RECT
D901
D504
KEY0 – KEY2
SHUNT
REGULATOR
IC931
8 STARTUP
RECT
D943
+1.8V
REGULATOR
IC110
P_CONT1 39
RESET 12
ISOLATOR
PC903
6 FB/OLP
23 LED1
74 KEY INT
S801 – 812
(FRONT & TOP PANEL KEY)
MAIN POWER
ON/OFF SWITCH
Q943
POWER CONTROL
IC921
P_CONT2 40
D817
D935
RECT
D931
+1.2V
REGULATOR
IC1
6 Q0
FOCUS
SUR
4 VCC
PWM_OUT 26
9 Q3
D815
DISC 5
(GRN)
B+ SWICH
Q904
+3.3V
REGULATOR
IC703
P_CONT3 41
D814
DISC 4
(GRN)
D908
RESET SIGNAL
GENERATOR
IC503
HCD-X1V
36
36
ISOLATOR
PC902
TH901
LINE FILTER
LF901
F901
(AC IN)
HCD-X1V
• Note for Printed Wiring Boards and Schematic Diagrams
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
f
: internal component.
•
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• DMB12 board is multi-layer printed board.
However, the patterns of intermediate layers have not been
included in diagrams.
• Indication of transistor
C
Q
These are omitted.
B E
Q
B
C
E
These are omitted.
• Circuit Boards Location
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
f
: internal component.
•
• 2 : nonflammable resistor.
• C : panel designation.
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
TUNER (FM/AM)
MAIN board
D-IO board
POWER-SW board
DMB12 board
AUDIO IN board
AMP board
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce por tant le numéro
spécifié.
LED board
• A : B+ Line.
• B : B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
– DMB12 Board –
no mark : DVD PLAY
– Other Boards –
no mark : TUNER (FM/AM)
(
) : DVD PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J : CD PLAY
c : DVD PLAY
F : AUDIO
L : VIDEO
E :Y
a : CHROMA
r : COMPONENT VIDEO
f : TUNER (FM/AM)
i : DIGITAL AUDIO IN
N : MIC INPUT
LF board
KEY board
DISPLAY board
POWER board
ROLLER MOTOR board
STOCKER MOTOR board
SW (4) board
ST ENCODER board
SW (3) board
SW (2) board
SW (1) board
SENSOR board
MODE MOTOR board
HCD-X1V
37
37
RELAY board
HCD-X1V
• See page 37 for Circuit Boards Location.
7-6. PRINTED WIRING BOARD – DMB12 Board (Side A) –
1
2
3
4
(Page 51)
B
9
(Page 50)
MAIN BOARD
CN505
C
CN601
MAIN BOARD
CN201
2
CN201
10
CN4301
1
11
FOR
CHECK
CN105
C218
2S
1G
1D
R111
R116
E
R4619
FB605
Q103
C220
Q101 R108
R4706
B
2D
2G
1S
R117
R4705
C101
R4703
R1110
R4704
CN101
R4701
B-5
B-5
8
R4702
Q101
Q103
7
C105
E-4
E-2
F-2
G-4
C-5
C-3
G-8
F-7
6
C112
IC101
IC102
IC103
IC104
IC110
IC201
IC701
IC708
DMB12 BOARD (SIDE A)
A
5
OPTICAL PICK-UP
BLOCK
KHM-310CAB
OR
KHM-313CAB
• Semiconductor
Location
Ref. No. Location
: Uses unleaded solder.
C221 C222
FB604
25
24
R230
C209
R1173
R4805
R4502
C118
C4501
1
12
R1145
C150
R1138
R1140
R1141
CN4501
2
10
1
256
65
R1142
11
1
64
IC102
E
R4803
11
C117
R4802
(Page 50)
10
R4501
R1143
2
A
R4520
FL4501
C119
13
48
R221
R212
CN109
MAIN BOARD
CN504
2
3
R226
R225
R223
1
IC110
IC201
C233
C211
D
1
R231
R220
C
C187
C217
37
R232
FB606
C603
C219
C602
R234
R233
C224
36
D
R4801
R1176
MAIN BOARD
CN701
C736
C153
(Page 50)
X101
R1715
C152
IC101
R152
R153
C160
FL705
R728
R183
C731
R185
R767
R159
RB112
16
R160
F
FB111
RB113
128
129
RB110 RB109 RB111RB103 RB104
R191
R1183
R1114
C177
RB107
RB116
RB108
R170
FB106
R166
R169
R167
IC104
64
17
C733
R790
R789
R763
R762
FL703
FL701
C702
IC708
80
R793
60
LF701
49
R771
33
48
C710
61
1
32
IC701
C701
LF702
CN701
LF703
HDMI
OUT
LF704
C713
41
21
40
C704
R1750
C190
C709
20
C1104
C1103
FB108
1
R1101
R140
RB117
G
R163
R164
R165
192
RB115 RB114
R171
R193
193
R1179
IC103
R161
R162
C707
X701
R184
C715
C102
FL704
C179
C180
C197
H
1-868-160-
HCD-X1V
Note: When the DMB12 board is replaced by a repair for a fee, throw away the DMB12 board after
obtaining consent of not returning of the DMB12 board to the customer. When throwing away
the DMB12 board, be sure to throw away after destroying EEPROM (IC103 and IC706) physically with the hammer etc.
38
38
11
Note: EEPROM (IC103) cannot exchange with single. When EEPROM
(IC103) is damaged, exchange the entire mounted board.
HCD-X1V
• See page 37 for Circuit Boards Location.
7-7. PRINTED WIRING BOARD – DMB12 Board (Side B) –
1
2
3
4
: Uses unleaded solder.
5
6
7
8
9
• Semiconductor
Location
Ref. No. Location
A
DMB12 BOARD (SIDE B)
C113
R123
R124
R115
R113
R1129
R107
FL602
R114
1C
1B
2E
R102
R112
C183
R1178
C198
FL603
R5010
R2504
R224
C210
R219
IC4502
1
5
FB112
C130
R136
R701
R745
R743
R753
IC707
C729
C730
4
3
6
1
R773
C734
R1710
R130
R135
R1177
R154
R1151
R155
R1152
R1150
R148
R156
R1115
C172
C174 C175
C176
R192
C1107
R138
S
R1184
R770
D
R765
R705
R756
R722
R783
R145
R147
R1123
R779
R778
R788
R723
R742
IC705
C725
R744
5
4
1
3
R752
D
G
C171
R195
R1124
R190
IC105
C173
R173
S
R784
C727
R718
R709
R708
R787
R712
R750
R749
R751
C703
R747
R725
R724
C714
G
C726
C712
R189
C162
R139
R1125
R781
R786
R782
R792
R730
Q701
R1751
C163
R1201
C158
R172
R1122
R785
R714
R748
R760
R764
IC706
C711
C161
R1120
R1121
R197
R769
C720
R1706
Q702
F
4
R759
3
IC703
R738
C156
R143
R1102
C723
C732
C718
6
IC111
C155
FB123
R772
1
C157
R1167
C717
R740
R1186
4
R1170
C144
R1400
3
6
3
C184
C136
R146
1
C131
C127
C149
1
R142
IC702
C151
R141
R126
R734
C147
C148
R1191
R1169
R731
4
C140
1
R175
R174
6
R1168
C125
C126
3
6
C164
R736
C128
R132
4
R103
C116
C133
C141
C145
C138
C142
C143
R1139
FB115
FB107
R4513
C139
R702
R703
R704
C716
C719
E
C199
C132
C137
C205
R208
R151
R1133
C182
4
C135
R1705
C124
C123
C122
C121
C120
C193
C195
C186
IC107 3
5
C154
C4504
C4502
4
R4512
R4510
R4511
R4514
R4515
R4516
(AEP, UK)
R5016
R206
R205
C203
R207 R209
C208
R210
R204
C213
C192
(US, CND)
C206
R215 R214
R213 R216
C114
C115
3 1
IC4501
G
C214
C212
R4527
R4518
D
B-5
G-4
G-4
R1134
R4620
R5004
R5014
Q102
Q701
Q702
C215
R105
R106
C
D-8
D-5
E-5
G-6
E-3
F-2
G-2
F-2
G-3
D-3
D-4
FL601
R4610
R101
R247
R246
1E
2B
2C
R121
R110
C106
R109
Q102
R118
R120
FB602
B
FB603
FB601
R4718
C105
IC107
IC111
IC150
IC702
IC703
IC705
IC706
IC707
IC4501
IC4502
R766
R780
C1106
R133
R1185
C181
C1105
IC150 4
R1503
5
C1501
3
R1502
1
R1501
RB106
C191
RB105
R754
H
1-868-160-
HCD-X1V
Note: When the DMB12 board is replaced by a repair for a fee, throw away the DMB12 board after
obtaining consent of not returning of the DMB12 board to the customer. When throwing away
the DMB12 board, be sure to throw away after destroying EEPROM (IC103 and IC706) physically with the hammer etc.
39
39
11
Note: EEPROM (IC706) cannot exchange with single. When EEPROM
(IC706) is damaged, exchange the entire mounted board.
HCD-X1V
• See page 72 for Waveforms.
7-8. SCHEMATIC DIAGRAM – DMB12 Board (1/6) –
• See page 74 for IC Block Diagrams.
(1/6)
REGO1
R102
0
R116
1k
Q101-1
DVD_LD
LD(650)
MSW
Q101-2
+1.8V REGULATOR
DVD ON SWTICH
IC110
MM1661JTRE
OSC BUFFER
VO
GND(LD)
GND
CD ON SWITCH
C101
0.01
VIN
CN101
24P
IC111
TC7PAU04FU
(TE85R)
N.C
R117
47k
N.C
PD
PD
CD_LD
LD(780)
Q101
UM6K1N-TN
GND
S
IC107
TK11133CSCL-G
INVERTER
R1168
220
VR(780)
S
-1
N.C
CONT
VOE
VOE/E+G
VDD
+3.3V REGULATOR
Q103
RT1N241C-T112-1
-2
VR(650)
R142
100k
R1167
0
VIN
SW+5V
X101
27MHz
GND
VOUT
VCC
RF+3.3V
NOISE
V2O
VC
R108
1M
R111
100
C192
0.01
C195
0.22
C193 C198
0.22
1
C183
0.33
C187
47
4V
R1178
1k
C153
15p
C152
15p
VOF
VOF/F+H
SW+3.3V
VOB
VOB/B
C106
0.01
VOA
VOA/A
(LO:DVD.HI:CD)MSW
VOD
VOD/D
IOP
R112
22
VOC
VOC/C
TRK-
TRK-
FCS-
FCS-
R118
22
R120
22
R110
47k
R121
22
R124
47k
C112
47
Q102-2
XRST1
CONTROL (FOR DVD)
SW+5V
IC150
TC7SZO8FU(TE85R)
R1501
0
GND
V
AUTOMATIC POWER
CD_LD
CONTROL (FOR CD)
R114
100k
R1129
100k
XRST
C113
0.01
R1502
0
R1503
0
G
R1169
47
R1191
0
R1186
0
TXD
TXD
C186
0.22
RXD
RXD
GND
C182
0.22
A13
R151
10k
A12
A9
+3.3V REGULATOR
(FOR CHECK)
SW+3.3V
V2REFO
V2REF0
A10
IC105
TK11133CSCL-G
C184
0.01
R1133
0
A11
NOISE
VOUT
GND
R1110
2.7k
RF MON
CONT
(Page
44)
XSYSRST
Q102-1
DVD_LD
R101
100
SW+3.3V
SWITCHING
Q102
QST8TR
CN105
6P
C157
0.01
FB123
C105
47
10V
AUTOMATIC POWER
R123
0
LDO1
C1501
R1134 0.01
0
FB112
-2-1
R109
0
FCS+
FCS+
FB106
R115
22
R107
10k
LDO2
TRK+
TRK+
REG02
R113
22
RF
RF
A7
A6
VIN
A4
A5
CN109
11P
(Page
42)
R1173
0
(Page 41)
A8
OCSW1/GND
R1143 0
XSYSRST
XSYSRST
FB108
R1145 0
3.3V_MNT
XIFCS
R1139 0
XIF5SY
S29AL032D70TF-CHE2-0601UC(US,CND)
R1140 0
IFSOI
S29AL032D70TF-CHE2-0611CE(AEP,UK)
XIFCS
XIFBSY
IFSDI
IC102
IFSDO
A16
R1170 0
XMAMUTE
A15
R1142 0
IFSCK
A14
XAMUTE
IFSCK
SD-RAM
IC104
EDS6416AHTA-75-E
TX27M
R1141 0
IFSDO
(Page 52)
FLASH ROM
R1138 0
A13
DGND
A12
N.C.
A17
A16
VSS
A15
RA4
BYTE
A14
RA5
VSS
A13
A-1
A12
DQ7
A0
A2
GND
A1
VCO
WF
SCL
IC103
BR24L64F-WE2
A10
A9
SDA
EEPROM
A20
A21
A10
HD6
DQ6
A8
FCSFCS+
FCS+
R193 1k
R191 1k
TRK+
CLKE
DQ12
HD4
N.C.
A18
A8
XRST
A6
EEWP
SCL
SDA
A7
A5
A4
A3
A2
CLK
UDQM
NC
XWR
A10
BA1
BA0
VSS
RY/BY
HD2
DQ2
A18
RD8
HD1
DQ1
A7
DQ8
C181
0.1
RD9
DQ9
A17
VDDQ
DQ9
RD10
DQ10
RD11
DQ8
A6
CS
RAS
CAS
WE
XTALI
VOD
RA0
VOC
RA10
VOB
BA1
VOA
BA0
VOE
RCS
VOF
RAS
EEWP
CAS
SDA
RWE
SCL
DQMO
LDQM
VSSQ
VDD
A5
XRD
OE
A4
RB107
0
RD12
VSS
A3
XROMCS
CE
A2
RD13
C191
0.1
DQ7
VSSQ
DQ6
DQ5
VDDQ
DQ11
DQ4
DQ12
DQ3
VDDQ
DQ13
RD14
A0
VOD
VOC
VOB
VOA
VOE
VOF
EEWP
SDA
SCL
XRST1
XRST
XSYSRST
RB106
47
XIFCS
RD7
XIF5SY
RD6
IFSOI
RD5
IFSDO
RD4
XMAMUTE
HD0
DQ0
(Page
44)
XSYSRST
RB108
0
A1
(Page 45)
RA2
RA1
HD3
DQ10
(Page 42)
XRST
C102
1
WP/ACC
FB111
A0
CLKE
DRCLK
DQM1
DQ11
A19
A1
A7
NC
A19
DQ3
R106
10k
A6
A11
RESET
R105
10k
A2
RA3
HD5
DQ5
VCC
TRK-
A3
A5
A9
RA11
DQ13
A4
A8
RA9
A9
WE
IOP
FCS-
RA7
RA8
DQ4
TRK+
HD7
DQ14
A20
TRK-
RA6
A11
A11
IOP
A0
VDD
DQ14
RD15
VSSQ
IFSCK
RB105
47
VSSQ
DQ2
DQ1
VDDQ
XIFCS
XIF5SY
IFSOI
IFSDO
XMAMUTE
IFSCK
(Page
41)
LDO2
LDO2
RD3
LDO1
RD2
V2REFO
RD1
TXD
RD0
RXD
LDO1
V2REFO
TXD
RXD
PD
A1
DQ15
PD
DQ0
V2O
VSS
C190
47
10V
A1
A2
C179
0.1
V2O
VDD
C180
0.1
C197
0.1
RF
RF
MSW
MSW
A3
(Page 41)
HCD-X1V
40
40
Note: EEPROM (IC103) cannot exchange with single. When EEPROM
(IC103) is damaged, exchange the entire mounted board.
HCD-X1V
• See page 72 for Waveforms. • See page 81 for IC Pin Function Description.
7-9. SCHEMATIC DIAGRAM – DMB12 Board (2/6) –
Y
V
C
R1124 R1125
R189
150
R190 150
R192
150
R195 150
R165
Y/G
CB/B
CR/R
R1121 R1122 R1123
R197 150
XMAMUTE
VSYNC
R1120
R1102
150
R167
SMSDI
HSYNC
SMSCK
XSMCS
SMSDO
R163
C161 0.01
ACLK
ALRCK
ABCK
R160 47
R159 47
R161 47
ASDATA0
ASDATA2
ASDATA1
ASDATA4
SPDIF
C156 0.01
C145 1
C149 0.1
C141 0.1
C143 0.1
R132 100k
C139 22p
C140 0.1
C135 0.033
C137 0.1
C130 0.1
C132 0.1
R136 15k
VREFO
XTALI
(2/6)
C163
0.01
C151 0.001
V2O
LDO2
R173 0
R172 0
R169 0
R166 0
R164 0
R162 0
R183 47
R184 47
R185 47
R146 47
R126 4.7k
C154 0.1
R143 47
C148
0.047
V2REFO
R141 680k
C147
0.047
C150 10 16V
C133
0.1
C142 0.1
C138 0.001
RF
FB107
LDO1
PD
XTALI
XMAMUTE
XIF5SY
XRST
SDA
YUV1
SCL
DAVSS
DAVDD
YUV2
DAVSS
YUV3
DAVDD
YUV4
DAVSS
YUV5
YUV6
YUV7
VSYN
DVDD3
SMBSY
SMSCK
SMSDI
SMSDO
ALRCK
DVDD3
XSMCS
ABCK
ACLK
DVSS
ASDATA0
SPDATA
ASDATA2
ASDATA1
DVDD18
ASDATA4
GPIO
DVSS
SDPIF
RFVDD18
RFGND18
XTALI
XTALO
JITFN
JITFO
IDAC
PLLVSS
LPFIP
LPFON
PLLVDD3
LPFIN
LPFOP
VSS
VCM
VDD3
VREFP
VREFN
RFVDD3
RFRPDC
HRFZC
RFRPAC
RFGND
CRTPLP
OSP
CEQP
OSN
CEQN
RFGC
AVDD3
IREF
XSYSRST
IFSOI
XIFCS
R1101 2.2k
C120 1
VOB
C121 1
VOC
C122 1
VOD
IFSCK
CIN
AGND
VOA
DVDA
FS
DVDB
DACVDDC
IFSDO
TXD
R174 0
DVDC
DAVCC
DVDD
XDACS
RXD
RF
C123 1
DVDRFIP
ADSDO
DVDRFIN
FWD
MSW
R175
0
EEWP
C1103 0.001
R1179 100
C124
1
C1104 0.001
R171 100
MA
REW
MB
MUTE123
VOA
VOB
R1185 100
C1105 0.001
MUTE123
VOC
R1184 100
C1106 0.001
MUTE
VOD
MUTE
MC
C171
MD
DVDD3
SA
TSD_M
0.01
VOE
R133 0
R140 10k
TSD_M
V2REFO
V2O
LDO2
LDO1
PD
XTALI
XMAMUTE
XIF5SY
XRST
SDA
XSYSRST
SCL
IFSOI
XIFCS
IFSCK
IFSDO
TXD
(Page 40)
RXD
MSW
EEWP
VOA
VOB
VOC
VOD
VOE
VOF
R170 10k
C125
0.1
SB
ADSCK
SC
WIDE
C1107 0.001
R138 100
R1183 220
VCLK
SD
RB116 47
SDFON
SMPTE_Y(0)
SDFOP
SMPTE_Y(1)
VOE
TNI
DVSS
TPI
SMPTE_Y(2)
VOF
WIDE
DMO
VCLK
FMO
YUV0
IOPMON
YUV1
TRO
YUV2
FOO
YUV3
SPFG
C172 0.01
PD
MDI1
DVDD18
MDI2
SMPTE_Y(3)
VREFO
MUTE123
RB117 47
LDO2
LDO2
SMPTE_Y(4)
LDO1
SMPTE_Y(5)
SVDD3
SMPTE_Y(6)
CSO
SMPTE_Y(7)
LDO1
C118
C117
10 C115 10 C114
16V 0.1
16V 0.1
RB114 0
SGND
RA4
V2REFO
RA5
RA6
V2O
VREFO
DVSS
VREFO
FEO
RF AMP,SERVO DSP,MPEG DECODER
TEO
IC101
CXD9804R
C126 0.1
YUV5
TSD_M
YUV6
LIMITSW
RA4
SPDIF
RA5
ASDATA2
RA6
ASDATA1
RA7
ASDATA0
ACLK
RA7
ABCK
DVSS
RB115 0
RA8
TEZISLV
RA9
OPOUT
RA11
OP_INN
C199
0.0047
MUTE
FMO
IOPMON
TRO
FOO
SPFG
VREFO
MUTE123
MUTE
TSD_M
LIMITSW
(Page 42)
DVDD3
RFLVL
V2O
C119
10
16V
YUV4
DMO
YUV7
V2REFO
C116
0.1
VOF
RF
CKE
OP_INP
R1114 22
DMO
DMO
DRCLK
FMO
DVDD3
TROPENPWM
RCLKB
RA8
ALRCK
RA9
CR/R
RA11
CB/B
CLKE
Y/G
DRCLK
C174 0.01
FMO
C
Y
IOPMON
WIDE
RVREF
IOPMON
V
SPDIF
ASDATA2
ASDATA1
ASDATA0
ACLK
ABCK
ALRCK
CR/R
CB/B
Y/G
(Page 43)
V
C
Y
WIDE
C175 0.01
TRO
TRO
DVDD18
FOO
RA3
RB104 0
FOO
USB_VSS
RA2
USBP
RA1
USBM
DVSS
C127 0.01
RB103 0
SPFG
RA10
MSW
BA1
MSW
EEWP
DVSS
CKSW
R1177
100
ASDATA4
RA1
ASDATA2
RA0
ASDATA1
ASDATA0
SPFG
R135
10k
SPDIF
RA2
RA0
USB_VDD3
R130
0.01
RA3
OCSW
BA0
EEWP
RCS
RA10
ACLK
BA1
ABCK
BA0
ALRCK
RCS
HSYNC
VSYNC
C176 0.01
VCLK
DVDD3
DVDD18
A2
RB111 0
HA2
RAS
HA3
CAS
HA4
RWE
HA5
DQM1
A3
A4
A5
A6
R139 0
RAS
YUV0
CAS
YUV1
RWE
YUV2
DQM1
YUV3
LIMITSW
YUV4
LINYSW
HA6
A7
HA7
RD8
HA8
DVSS
A8
YUV5
RB109 0
C173 0.001
A18
HA18
RD9
HA19
RD10
A19
RD8
YUV6
RD9
YUV7
SPDIF
ASDATA4
ASDATA2
ASDATA1
ASDATA0
ACLK
ABCK
ALRCK
HSYNC
VSYNC
VCLK
YUV0
YUV1
YUV2
(Page 44)
YUV3
YUV4
YUV5
YUV6
YUV7
RD10
RD11
APLLCAP
RD12
RB110 0
XSMCS
RD12
SMSDO
RD13
SMSDI
RD14
RD15
DVDD3
RD0
RD1
RD2
DVDD18
RD3
RD4
DVSS
RD5
RD6
DVSS
RD7
XIF5SY
DQMO
XTXINT
RD13
IR
ICE
XSYSRST
DVDD3
TXD
RXD
XRST
TRG-SW
IFSOI
SDA
SCL
IFSCK
XIFCS
IFSDO
DVDD18
DVSS
URD
UWR
HA0
HA17
HD7
ALE
HA21
HD6
HD5
HD4
DVSS
HD3
HD2
HD1
HD0
DVDD3
XRO
HA1
HA20
XROMCS
HA9
HA10
DVDD3
HA11
HA12
HA13
HA15
HA14
HA16
APLLVSS
XWR
C128 0.0015
APLLVDD3
R103 0
DVSS
RD11
RD14
SMSCK
RD15
VSYNC
XSMCS
SMSDO
SMSDI
SMSCK
VSYNC
GND
(Page 45)
A4
A5
A6
A7
A8
A9
FB115
A10
C177 47 10V
C164 0.01
C162 0.01
R1115 0
C160 0.01
R155 0
C158 0.01
R1400
R154 0
R152 0
R147 0
R148 0
R1151 3.3k
R1150 3.3k
R153 0
R145 0
R1201
3.3k
R1152 3.3k
C155 0.01
A0
HD7
A17
R1176 0
A21
HD6
HD5
HD4
HD3
HD2
HD1
HD0
XRD
A1
A20
A9
A11
A10
A12
A13
A14
A15
XWR
A16
(Page
40)
XROMCS
C131 2.2
C136 0.01
C144 0.01
A11
R156
100
RB112
0
RB113
0
RD0
RD1
RD2
RD3
RD4
RD5
RD6
RD7
DQMO
TXD
XRST
RXD
SDA
SCL
IFSOI
XIFCS
IFSCK
IFSDO
A3
XSYSRST
A2
XIF5SY
A1
HCD-X1V
41
41
A12
A13
(Page 40)
HCD-X1V
7-10. SCHEMATIC DIAGRAM – DMB12 Board (3/6) –
IOP
IOPMON
(3/6)
RF+3.3V
R223
100k
SW+5V
R246 4.7k
SW+3.3V
REGO1
C209
0.033
R221
56k
C211
0.033
C233
0.0047
VREFO
R225
100k
REG02
(Page 40)
C214
0.001
SPFG
C212
0.01
R231
15k
SW+5V
R232 R234
18k 10k
R220
1k
FCS-
SW+3.3V
R233
33k
GND
R226
56k
R212
10k
R230
82k
SW+9V
MTR_GND
(Page 43)
FCSFCS-
FOCUS/TRACKING COIL DRIVE,
FCS+
FCS+
SPINDLE/SLED MOTOR DRIVE
TRK+
TRK+
TRKTRK-
R214
15k
FOO
IOP
C205
R208
220p
33k
TRK+
R206
10k
TRK-
(Page 40)
VREFO
VREFO
SPFG
R215
12k
TRO
IOP
FCS+
SPFG
FOO
FOO
TRO
C220
10
16V
C206
R209
220p
33k
TRO
FMO
FMO
DMO
DMO
C224
0.01
MUTE123
MUTE123
MUTE
C203
0.01
R207
2.7k
C218
10
16V
R204
1.2k
C221
0.1
R205
10k
TSD_M
TSD_M
R247
1k
IOPMON
IOPMON
LIMITSW
SL-
SL+
SPC222
0.1
R216
12k
FMO
MUTE
C219
0.01
SP+
CN201
6P
SPSPSP+
R210 C208
47k 0.01
SP+
LIMIT
IC201
FAN8036L
(GND) LIMIT
SL-
R213
6.8k
SLSL+
C215
0.01
SL+
C217
47
16V
MUTE123
R2504
4.7k
C213
0.01
R224
10k
C210
0.01
MUTE
R219
27k
TSD_M
DMO
HCD-X1V
42
42
(Page 41)
HCD-X1V
7-11. SCHEMATIC DIAGRAM – DMB12 Board (4/6) –
(4/6)
CN601
5P
MTR_GND
MGND
FB601
FB605
SW+9V
SW+9V
SW+3.3V
FL602
SW+3.3V
DGND
GND
(Page 42)
C603
47
FB606 10V
SW+5V
FB604
C602
47
10V
(Page 52)
FL603
FL601
SW+9V
SW+5V
FB603
FB602
FL4501
SW+3.3V
C4501
10
C4502
0.01
R4610
0
R4619
0
R4620
0
CN4301
11P
(Page 45)
R4701 0
CR/R
CR/R
WIDE
WIDE
R4702 0
CB/B
CB/B
V-GND
R4703 0
CY/G
Y/G
V-GND
R4704 0
Y
Y
V-GND
R4705 0
C
C
(Page 57)
V-GND
R4706 0
CVBS
V
R4718 0
SPDIF
BUFFER
IC4501
SN74LVC541
CN4501
11P
GND
(Page 41)
D-GND
R4514 100
R4527
0
D1
R4515 100
D2
ASDATA0
R4516 100
D3
ASDATA1
R4510 100
BCKO
ASDATA2
R4803 0
R4502 0
R4511 100
LRCKO
ABCK
D-GND
ALRCK
R4801
0
R4512
R4805
0
MCKO
R4518
0
ACLK
R4802
0
D-GND
R4513 0
R4501
0
SPDIF
VCC
C4504
0.01
D-GND
R5016
0
BUFFER
R5014
0
IC4502
TC7SZ125FU
(TE85R)
R4520
0
R5010
0
GND
R5004
0
VCC
HCD-X1V
43
43
(AEP,UK)
(US,CND)
(Page 54)
HCD-X1V
7-12. SCHEMATIC DIAGRAM – DMB12 Board (5/6) –
• See page 74 for IC Block Diagrams. • See page 81 for IC Pin Function Description.
C717
0.01
(5/6)
SW+3.3V
R740
0
C718
0.01
SW+5V
R734
0
GND
(Page 40)
C716
0.22
R1705
1k
C719
0.22
R728
0
CONT
VIN
HDMI TRANSMITTER
R738
0
ABCK
FL703
FS
VREF
AVSS
AVSS
DAC_AVDD3
C0
DAC_AVDD3
G
B
AVSS
R
AD3
DAC_AVDD3
DVSS
SPDIF
ACLK
SPDIF
AD2
ACLK
SPDIF
C723
0.22
ALRCK
AD1
ABCK
ASDATA0
AD0
ALRCK
ASDATA1
ACL
ASDATA0
C720
0.22
C707
22
10V
R731
0
ABCK
ASDATA1
ASDATA2
ALRCK
ASDATA2
R1706
1k
FL701
ASDATA4
DVDD18
ASDATA4
NOISE
VOUT
IC703
TK11133CSCL-G
GND
+3.3V REGULATOR
C736
47
4V
C709 0.1
R714 0
CONT
IC702
TK11118CSCL-G
VIN
+1.8V REGULATOR
GND
NOISE
VOUT
SPDIF
ASDATA2
ASDATA4
R793 0
ASDATA1
ACLK
ASDATA0
ABCK
R704 0
R703 0
R702 0
C702 0.1
ALRCK
R736
0
SWING
R730 510
CN701
19P
C710
10
16V
HDMI
OUT
AVSS
C1
TX2P
C2
TX2N
LF701
TMDS DATA2 +
TMDS DATA2 SHIELD
C711 0.1
C701
0.1
R701
0
AVDD3
C4
TX1P
C5
TX1N
C6
AVDD
C7
TMDS DATA2 -
LF702
TMDS DATA1 +
TMDS DATA1 SHIELD
TMDS DATA1 -
LF703
TX0P
IC701
CXD9873Q
DVDD33
TMDS DATA0 +
TX0N
TMDS DATA0 SHIELD
C712 0.1
VCK
VCLK
AVDD3
TMDS DATA0 -
LF704
YUV3
Y3
PLL_AVDD3
YUV4
Y4
PLL_AVDD3
YUV5
Y5
PLLC1
YUV6
Y6
PLLC0
YUV7
Y7
TMDS CLOCK CEC
FL704
R747
0
EEPROM
C714
0.1
RESERVED
IC706
BR24L16F-WE2
SCL
SDA
R751
0
A0
A1
A2
R748
0
SCL
DOC/CEC GND
+5V POWER
VCC
R749
1.8k
WP
AVSS
C715
47
10V
GND
C713
0.0056
SDA
MSD
MSCK
TRAP0
TRAP2
INT
RST
PWDN
SSO
HTPLG
AVSS
HSYNC
Y2
VSYNC
YUV2
ASDATA4
AVSS
TYPE
Y1
TRAP1
TMDS CLOCK SHIELD
YUV1
A6
TCKN
A7
Y0
DVSS
TMDS CLOCK +
YUV0
CLK
TCKP
DVDD18
DVSS
SSCK
(Page 41)
C3
HPD
R752
0
R750
1.8k
GATE SWITCH
IC705
TC7SZ08FU
(TE85R)
G
R1750 10k
R724 0
R725 0
R722 10k
R718
4.7k
R723 10k
C703 0.01
R788 0
R712 100
R705 4.7k
R708 1k
C704
0.1
R709 1k
HSYNC
R744
4.7k
R743
1k
R787
4.7k
B1
V
R742
47k
C725
0.01
C726
0.1
R745
1k
B2
B3
B4
R1751
10k
B5
B6
VSYNC
B7
B8
(Page 45)
B9
TX27M
B10
B11
(Page 40)
HCD-X1V
44
44
Note: EEPROM (IC706) cannot exchange with single. When EEPROM
(IC706) is damaged, exchange the entire mounted board.
HCD-X1V
7-13. SCHEMATIC DIAGRAM – DMB12 Board (6/6) –
• See page 72 for Waveforms.
• See page 74 for IC Block Diagrams.
• See page 81 for IC Pin Function Description.
(6/6)
B11
B10
B7
R772 0
R762 0
R763 0
B8
B6
B4
B5
AVR
PE3/
INT13
PE2/INT12
PE1/INT11
TRG1/P53
P83
PPG1/P52
B3
Q702
2SK1399-T1B
LEVEL SHIFT
R785
0
(Page 44)
S
R782 10k
SCL0
R786
0
EC0/P24
C727
0.01
R754
0
TO01/P23
P71/TI0
TO00/P22
P70/TO0
MOD
PPG01/P21
X0
PPG00/P20
VIN CONT
R765
0
GND
R792
4.7k
ADTG/
TRG0/
P13
NOISE
VOUT
SDO
SDI
P07/INT07
P06/INT06
P05/INT05
P03/INT03
XSMCS
XTXINT
VSYNC
XRST
PG2/X1A
PG2/X0A
VDD
PG0/(CIN)
VSS
P04/INT04
PPG0/P14
X1
R766
4.7k
R783
0
SDA0
P80
R767
0
B2
S
R781 10k
IC708
MB95F108ASPFVGE1-H0601
P82
R784
0
LEVEL SHIFT
EC1/
P64
T011/
P63
T010/
P62
PPG11/
P61
PPG10/
P60
PE0/INT10
P81
X701
10MHz
Q701
2SK1399-T1B
SCK
C732
0.01
HDCP-SCL
HDCP-SDA
P43/AN11
HDCP-WP
P42/AN10
P40/AN08
P41/AN09
P37/AN07
P35/AN05
AVCC
P36/AN06
XPWDN
XTXRST
SDA
TRAP2
SCK
AVSS
HDMI CONTROLLER
+5V REGULATOR
IC707
TK11150CSCL-G
SW+9V
B1
R764 4.7k
R790 4.7k
R753
0
B9
R756
10k
C734
0.01
R1710
4.7k
R780 0
C731
22
10V
R759 0
FL705
R760 100
R773 100
(Page 43)
R789 0
SW+3.3V
C733
0.01
GND
VSYNC
R1715 0
XSMCS
R771 0
SMSCK
R779 0
(Page 41)
SMSDI
R770 0
R778 0
SMSDO
R769 0
XRST
(Page 40)
HCD-X1V
45
45
C729
0.22
C730
0.22
HCD-X1V
7-14. PRINTED WIRING BOARDS – CHANGER Section –
1
• See page 37 for Circuit Boards Location.
3
2
: Uses unleaded solder.
4
5
6
7
MODE MOTOR BOARD
4
3
G
2
SW(1) BOARD
S771
ROTALY ENCODER
(MODE)
1
S771
S711
(DISC INSERT (8/12cm))
(ON: When disc insert)
(Page 50)
RELAY BOARD
E
M771
(MODE)
MAIN
BOARD
CN621
2
1
1
CN701
1
7
13
7
1-686-724-
1
CN710
26
R733
S714
(DISC IN (8cm))
(ON: Play position (8cm disc only))
C762
JW726
2
CN721
CN705
STOCKER MOTOR
BOARD
JW722
JW720
JW709
C753
C752
C761
C751
JW706
1
R712
(13)
JW735
JW727
IC721
1
CN704
CN706
2
JW734
JW701
R721
D721
JW702
R722
JW707
1
C754
1
JW733
13
1-686-728-
1
3
4
JW703
(13)
ROLLER MOTOR BOARD
M
9
IC711
R711
1
2
G
3
M761
(STOCKER)
CN761
4
13
1-686-731-
D711
CN703
2 1
(13)
13
JW708
2
2
1
1
C781
1-686-725-
CN781
(13)
S702
ROTALY ENCODER
(STOCKER POSITION)
M
D
JW732
9
JW704
1-686-723-
C763
JW710
1
JW731
C766
C769
3
4
C767
S713
S714
3
CN707
JW711
C764
D701
C765
R702
13
M781
(ROLLER)
IC701
9
R701
JW705
1
1
3
2
1
C755
C768
1
C
C756
JW712
CN751
1
JW728
E
JW714
C758
JW725
CN708
1 CN702 3
JW730
Q731
C711
SENSOR BOARD
JW724
JW723
R734
S713
(DISC IN (8/12cm))
(ON: Play position)
JW729
JW721
JW718
JW717
R731
JW716
JW719
R732
JW715
B
JW713
C771
2
13
(13)
SW(2) BOARD
27
2
(13)
IC751
S711
1-686-727-
CN771
M
CN711
A
8
SW(3) BOARD
13
SW(4) BOARD
S718 (STOCKING)
OFF: In the midst disc is moving
between play position and
stocker
1-686-726- (13)
13
S715
1-686-732- (13)
S718
2
1-686-729S715
(DISC OUT)
OFF :When disc out
from play position
E
1
13
(13)
S717 (DISC POSITION)
4
CN741
CN731
ST ENCODER
BOARD
S716
S717
1
13
In the midst disc is moving
between play position and stocker
ON : disc is play position side
OFF : disc is stocker side
(13)
1-686-730-
S716 (STOCKER IN/OUT)
ON:The moment disc in/out
from stocker
• Semiconductor
Location
Ref. No. Location
D701
D711
D721
C-4
D-3
C-4
IC701
IC711
IC721
IC751
C-4
D-3
C-4
C-2
Q731
B-5
HCD-X1V
46
46
HCD-X1V
• See page 74 for IC Block Diagrams.
7-15. SCHEMATIC DIAGRAM – CHANGER Section –
CN751
3P
DIODE
D SENSE
GND
CN702
3P
R731
91
DIODE
D SENSE
R733
10k
GND
R734
10k
IC751
RPR-220
GND
D+3.3V
Q731
RT1N141
RIN
VCC
FIN
OUT1
VM
OUT2
RNF
VREF
DETECT SENSOR
CN701
27P
3.2
R732
1k
DISC INSERT
MODE MOTOR
M+12V
LEVEL
SHIFT
DRIVE
M+12V
MGND
MGND
IC701
BA6956AN
D.SENSOR
C754
0.1
C711
10
50V
R702
100
C758
0.1
C755
0.1
C756
0.1
R701
680
D701
MTZJ-T-77-5.1C
C751
0.1
C752
0.1
CN781
2P
SW3
SW1-A SW1-B
SW2A
SW2-A
SW2B
SW2-B
SW5B
SW5-B
SW5A
SW5-A
SLD (MD) POS
CN703
2P
MTR RL 2
MTR RL 2
MTR RL 1
MTR RL 1
C781
0.01
SLD (MD) NEG
RIN
GND
VCC
FIN
VM
RNF
OUT1
VREF
LOD (ROL) POS
(ROLLER)
OUT2
M781
SW3
SW1
LOD (ROL) NEG
ROLLER MOTOR
ELV-POS
DRIVE
E
MAIN
BOARD
(1/6)
CN621
(Page 52)
ELV-NEG
SW4
GND
RIN
VCC
FIN
VM
RNF
OUT1
VREF
OUT2
SW4
IC711
BA6956AN
C753
0.1
STOCKER MOTOR
SLD-E1
R712
100
DRIVE
SLD-E2
IC721
BA6956AN
CN761
2P
M761
CN704
2P
MTR ST 2
MTR ST 2
MTR ST 1
MTR ST 1
C761 R722
0.01
100
SLD-E0
SLD-E3
C765
0.1
D711
MTZJ-T-77-6.2A
R711
680
ELV-E0
ELV-E1
C764
0.1
ELV-E2
C763
0.1
ELV-E3
(STOCKER)
D721
MTZJ-T-77-4.3B
C762
0.1
R721
680
CN711
2P
CN705
2P
GND
GND
SW1
SW1
SW1
S702
ROTARY ENCODER
(STOCKER POSITION)
S711
(DISC INSERT(8/12cm))
(ON:WHEN DISC INSERT)
CN721
3P
GND
S713
CN706
3P
GND
SW2-A
SW2-A
SW2A
SW2-B
SW2-B
SW2B
(DISC IN(8/12cm))
(ON:PLAY POSITION)
S714
(DISC IN(8cm))
(ON:PLAY POSITION(8cm DISC ONLY))
S771
ROTARY ENCODER
(MODE)
CN731
2P
CN707
2P
GND
GND
SW3
SW3
CN710
7P
C769
0.1
SW3
S715
(DISC OUT)
C768
0.1
CN771
7P
E1
E1
E2
E2
GND
C767 0.1
E3
C766 0.1
E4
GND
E3
(ON:WHEN DISC OUT FROM PLAY POSITION)
CN741
4P
GND
S716
(STOCKER IN/OUT)
CN708
4P
E4
MTR MD 1
MTR MD 1
MTR MD 2
MTR MD 2
C771
0.01
GND
SW5-B
SW5-B
SW5B
M771
SW5-A
SW5-A
SW5A
(MODE)
SW4
SW4
SW4
ON:THE MOMENT DISC IN/OUT
FROM STOCKER
S717
(DISC POSITION)
IN THE MIDST DISC IS MOVING
BETWEEN PLAY POSITION AND STOCKER
ON:DISC IS PLAY POSITION SIDE
OFF:DISC IS STOCKER SIDE
S718
(STOCKING)
OFF:IN THE MIDST DISC IS MOVING
BETWEEN PLAY POSITION AND STOCKER
HCD-X1V
47
47
HCD-X1V
• See page 37 for Circuit Boards Location.
7-16. PRINTED WIRING BOARDS – D-IO/AUDIO IN Boards –
1
2
3
4
5
: Uses unleaded solder.
6
7
8
9
10
11
12
AUDIO IN BOARD (COMPONENT SIDE)
D-IO BOARD (COMPONENT SIDE)
A
C1005
R1000
R1010
R1007
FB1001 C1001
C1007
C1010
R1014
C1003
FL1001
IC1004
R1012
IC1003
R1001
FL1000
C1004
11
1-870-014-
11
R1015
1-870-013-
B
(11)
(11)
DIGITAL IN
J1000
VIDEO 1
TV
OPTICAL
D-IO BOARD (CONDUCTOR SIDE)
OPTICAL
S1000
DIGITAL INPUT
SELECTOR
OPTICAL t COAXIAL
C
IC1000
AUDIO IN BOARD (CONDUCTOR SIDE)
(CHASSIS)
IC1001
R1016
CN1000
R1004
3
C1000
VIDEO 2
COAXIAL
COAXIAL
R1011
R1008
R1013
R1009
1
R1005
3
1
R1003
FB803
C1006
FB805
C1009
7
C836
R1002
11
FB1000
1-870-013-
FB804
4
1
CN808
11
(11)
D
FB806
F
1-870-014-
MAIN BOARD
CN508
(Page 51)
P
J801
AUDIO IN
HCD-X1V
48
48
MAIN BOARD
CN401
(Page 51)
(11)
HCD-X1V
7-17. SCHEMATIC DIAGRAM – D-IO Board –
• See page 74 for IC Block Diagrams.
A_SEL0
C1003
22
16V
A_SEL1
DGND
D3.3V
SPDIF-OUT
OPTICAL RECEIVER
R1015
100
IC1000
TORX147L
FL1001
DGND
DIGITAL AUDIO SELECTOR
R1001
0
DIGITAL-IN
TV
IC1004
TC74HC151AF
OPTICAL
C1000
0.1
FB1000
0
S1000
R1012
100
DIGITAL INPUT
SELECTOR
COAXIAL
R1004
100
R1005
10k
OPTICAL
D3
VCC
D2
D4
D1
D5
D0
D6
Y
D7
W
A
ST
B
GND
C
C1005
0.1
R1000
0
DIGITAL IN
OPTICAL
IC1001
TORX147L
C1001
0.1
FB1001
0
R1008
470k
R1011
470k
R1014
100
OPTICAL RECEIVER
VIDEO1
WAVE SHAPER
C1007
47
16V
J1000
2P
IC1003
TC74HCU04F
C1006
0.1
R1007
470
C1009
0.1
R1010
470
R1009
47k
COAXIAL
R1003 75
R1002 75
VIDEO2
COAXIAL
R1016 0
C1010
47
16V
R1013
47k
(CHASSIS)
HCD-X1V
49
49
(Page 53)
CN1000
7P
FL1000
C1004
0.1
HCD-X1V
• See page 37 for Circuit Boards Location.
R624
C28
C43
73
R64
C728
R742
5
R712
L704
IC77131
R572
1
C771
5
4
R575
R217
C355
C707
R365
C364
C705
E
C366
R360
R230
R223
R224
R308
R315
E
Q397
Q305 R340
R301
R398
R339
C334
R425
R413
IC351
R412
R414
C413
R433 R431
C411
R362
C304
R311
R618
C323
(US, CND)
11
C423 C422
R619
L300
R300
C306
C303
IC401
C421
C305
R432 R430
C302
C344
C412
C424
I
E
C358
FB301
C419
C332
R350
R352
C365
R335
R336
R310
R364
Q304
E
C342
R349
Q301
C531
50
C312
R345
R356
IC350
R316
C708
C526
HCD-X1V
R229
R228
R226
R701
R355
R709
R721
C529
C718
IC504
C528
50
Q396
R302
R354
R707
R711
C524
C525
5
C532
R325
Q302
R326
R710
IC701
C717
H
C354
C359
IC507
R573
FB508
E
Q395
R358
E
C360
C729
FB505
C537
E
R346
1
R555 R550
FB506
R764
R726
C545
R593
C546
C533
C712
C721
R741 R735
IC703
R570
1
R548 C543
C309
C723
IC360
G
R740
C218
R719
C732
C731
5
C544
C710
R713
R307
FB2
R745
R744
R640
R204
IC200
C213
C716
R317
D503
C719
R722
R723
FB507
R716 C711
R739
R517
C519
C212
R718
R637 5
R529
C535
R725
C727
C720
R205
C203
FB704
C709
C2
IC505
C534
R728
R727 FB703
C401
R424
R422
R423
R4
R203
C201
R309
C1
1
1
C724
C356
C504
C205
L202
C725
R750
IC702
R734
C513
IC1
L701
FB501
FL502
R733
R736
R738
R201
R216
C7
5 C6
R643
R518
C217
R202
C202
C220
L702
R14
C540
FL501
FB510
R732
C11
FB1
R15
R2
C549
E
R729
X701
C200
C733
3
1
R731
C548
C536
R327
R359
FB503
C542
FL503
F
R200
4
5
R730
C204
R747
IC705 IC706
FB509
L201
C216
C702
C730
R636
R645
C219
R60
R65
C81
R3
FB701
C71
IC202
C77
R57
R58
R59
L200
R608
C74 C73
R67
R596
R534
R523
R528
C79
72
C76
R547
C541
IC201
C215
R218
36
R748
C550
R638
50
R55
R56
C67
C80
C539
1
R544
C214
R53
R558
IC506
C225
L203
R51
R52
C62
C70
5
R220
R48
IC2
37
R542
R47
C64
51
31
C206
C224
C39
108
C42
R54
30
IC203
C207
C57
R639
R206
R214
C232
C25
109
C49
R49
R50
C234
R27
R26
R25
R24
C26
C30
1
R43
R45
R545
R540
R556
E
C211
C226
C227
C3
C46
Q503
R536
C522
C233
C40
X501
4
3
IC503
R28
C24
C34 C32
R66
D501
R41
IC501
5
C236
R763
R21
144
R525
80
R563
C523 1
R757
C751
R32
81
R532
E
R562
C520
C521
FB502
C9
C10
R35
R23
100
1
D
C752
FB752
R30
R29
R512
C502
R510
C501
R503
R38
R597
R561
R606
R752
R17
R16
Q501 C516
E
R592
R580
C503
R514
R522
R524
IC704
C231
R519
1
R537
E
R761
R759
R749
R762
R760
R758
R20
R36
3
4
5
Q502
C511
R604
R13
X1
R509
R521
R605
FB751
R630
R629
R508
R502
R511
(Page 66)
C506
IC502
C509
R501
R513
R526
R602
R603
R601
RB623 RB624
RB621 RB622
FB702
R530
DISPLAY
BOARD
CN801
R706
R705
R631
C624
R751
R635
RB630
R625
R628
R533
CN501
G
C704
R622
IC621
R621
RB629
R634
C625
R535
C
R633
RB625
R623
R591
R583
R582
RB601 RB602 RB603
R632
RB626
IC622
B
CN201
R702
C626
C627
Q504
R589
R586
R587
R588
R584
R585
R576
R724
H-8
G-8
H-8
H-10
G-10
G-10
H-10
C-3
C-3
D-4
B-4
E-9
R577
L703
Q301
Q302
Q304
Q305
Q395
Q396
Q397
Q501
Q502
Q503
Q504
Q701
C602
E
DMB12
BOARD
CN4301
C
CN701
CN621
11
(Page 38)
DMB12
BOARD
CN4501
D
CN507
CN504
C706
F-6
D-7
F-9
D-9
E-9
C-10
G-9
I-9
H-8
I-10
D-5
C-3
D-4
H-5
G-4
F-3
G-4
B-6
B-5
H-7
F-8
G-6
B-8
E-8
E-8
H-7
10
(Page 38)
AMP
BOARD
CN3700
J
C713
IC1
IC2
IC200
IC201
IC202
IC203
IC350
IC351
IC360
IC401
IC501
IC502
IC503
IC504
IC505
IC506
IC507
IC621
IC622
IC701
IC702
IC703
IC704
IC705
IC706
IC771
9
(Page 58)
RELAY
BOARD
CN701
E
(COMPONENT SIDE)
A
8
(Page 46)
DMB12
BOARD
CN109
A
MAIN BOARD
7
C714
D-4
G-4
6
(Page 38)
Ref. No. Location
D501
D503
5
R227
4
Q701
3
R18
2
RB628
1
RB627
• Semiconductor
Location
: Uses unleaded solder.
R221
7-18. PRINTED WIRING BOARD – MAIN Board (Component Side) –
R401
R402
C404
C403
1-870-013-
(11)
HCD-X1V
7-19. PRINTED WIRING BOARD – MAIN Board (Conductor Side) –
1
2
3
4
• See page 37 for Circuit Boards Location.
5
6
7
: Uses unleaded solder.
8
9
10
• Semiconductor
Location
11
(Page 38)
B
MAIN BOARD (CONDUCTOR SIDE)
A
DMB12
BOARD
CN601
Ref. No. Location
(CHASSIS)
CN505
C601
C505
J200
COMPONENT
VIDEO OUT
PB/CB
R755
R753
R756
Y
L705
R754
C208
R207
(US, CND)
C
C510
R504
R506
C209
R609
R208
C228
R210
R209
R594
C229
C19
C36
C230
C210
C33
R211
C29
D
R505
C35
R557
C508
C45
C23
C507
C515
VIDEO
C50
C517
C52
J201
MONITOR
OUT
4
S VIDEO
3
2
C55
(CHASSIS)
C518
C59
R539
1
C61
R579
C63
C66
C78
C75
C551
R549
R552
C85
J202
VIDEO1
E
4
3
2
(CHASSIS)
1
(CHASSIS)
C538
VIDEO IN
J203
4
VIDEO2
2
3
(CHASSIS)
1
F
C722
R737
J301
C307
C737
R642
R305
R
R303
C738
VIDEO1
C308
L
CN506
R306
G
1
R304
C341
R342
J301
AUDIO IN
R
R341
VIDEO2
C331
L
H
R332
R331
D702
R347
R743
R746
C343
H
POWER
BOARD
CN904
R708
R348
R
(Page 68)
D701
TV
D502
13
C333
L
C715
R338
C406
D504
R337
R419
R449
J401
A.CAL MIC
ECM-AC1
R448
R408
C471
R421
C420
R420
R447
R409
I
R418
R471
CN401
R472
C405
R406
R411
R410
C410
R415
R403
R470
C547
R474
R404
1
CN508
7
C527
R600
R574
R407
C402
IC300
R405
(AEP,UK)
3
C473
R446
R416
(Page 48)
1
CN303
11
1-870-013-
J
P
AUDIO IN
BOARD
CN808
R417
R473
F
D-IO
BOARD
CN1000
(Page 48)
(CHASSIS)
TUNER (FM/AM)
SUPPLIED WITH THE
ASSEMBLED BLOCK
FM 75Ω
COAXIAL
AM
ANTENNA
HCD-X1V
51
51
H-10
H-10
H-7
H-7
IC300
J-7
5
1
PR/CR
B
D502
D504
D701
D702
(11)
HCD-X1V
• See page 74 for IC Block Diagrams. • See page 81 for IC Pin Function Description.
7-20. SCHEMATIC DIAGRAM – MAIN Section (1/6) –
R633
100
(1/6)
A1
A2
CLKO
DO1
MEN10
LATCHO
DI2
SEN8
P7
MC2
MA2
P4
MA1
P3
MB2
SEN5
R634 220
RESET_B
IORST
RB629
10k
VSS
R547
1k
R542
12k
C534
100
16V
C519
0.1
R637
22k
+12V REGULATOR
IC507
SI-3010KM-TL
+5V REGULATOR
IC506
SI-3010KM-TL
VCC
SEN7
SW3
D-SEN
C626
0.01
R625
0
R628
100
+3.3V
REGULATOR
R632
100
R570
1k
C546
100
16V
C625
0.1
M+12V
R544
1k
C504
0.1
D+3.3V
CHANGER CONTROLLER1
D503
UDZW-TE17
-20B
IC621
BH2210FV-E2
CN621
27P
CLKO
R548
100
DO1
LATCHO
R621
100
DI2
RB624 220
P8
R622
10k
SEN8
P7
MC1
MB2
P4
P13
SEN3
P14
D-SEN
C529
0.47
C527
2200
6.3V
D502
1SS355WTE-17
EN
P1
P15
C531
0.1
C528
100
16V
(Page
71)
D-GND
P_CONT2
FB505
E6V
IN
P0
R631 220
LATCH
IOCE
R600
0
GND
DO2
R630 220
CLK
DI1
IOCLK
IORST
R629 220
RESET_B
RB627
10k
D504
1SS355WTE-17
D+3.3V
FB508
E4_D+3.3V
OUT
FB
VSS
CTLIO
C624
0.1
C526
100
16V
E13V
P2
RB621 100
A-GND
12V
SEN4
RB623 220
P12
MA1
A-GND
E+4V
P3
MA2
A12V
CN506
13P
C532
0.1
SEN5
P11
MB1
C540
100
16V
FB506
SEN6
P10
P5
RB628
10k
C544
47
25V
C513
100
16V
SEN7
P9
P6
RB622 100
MC2
C539
0.1
C543
0.1
(Page
56)
R518
1k
C602
0.1
R573 R572
100k 300k
VCC
C505
0.1
C524
47
16V
C537
0.001
R574
0
FB503
FL501
D-GND
E6_D+5V
FB510
M+9V
C525
0.1
+5V REGULATOR
R624
0
(Page
54)
M-GND
R642
3.3k
IC504
NJM2887DL3
C547
0.1
(CHASSIS)
R517
10k
C545
0.1
C627
0.01
MGND
C601
0.1
R529
1k
IC505
SI-3010KM-TL
CTLIO
D.SENSOR
M+12V
R636
47k
R575
1k
GND
OUT
CLK
DI1
SEN3
SW1-B
MGND
C541
0.1
LATCH
DO2
SW2-A
C542
100
16V
FB509
C536
47
16V
MEN10
P0
SEN4
SW2-B
R640
0
EN
FB
SW5-B
P15
R623
100
R550
10k
MEN11
P14
P1
SEN6
SW5-A
MEN12
P13
P2
MB1
SLD(MD)POS
FL503
FB502
R555
10k
IN
SLD(MD)NEG
R593
100k
MEN13
RB625 220
P12
GND
OUT
LOD(ROL)POS
C535
47
16V
MEN20
P11
R643
10k
FB507
EN
FB
LOD(ROL)NEG
MEN21
P10
P5
R645
10k
(Page 53)
FL502
FB501
MEN22
P9
P6
MC1
ELV-POS
RB630
10k
IN
ELV-NEG
MEN23
RB626 220
P8
GND
OUT
SW4
IN
SLD-E0
P_CONT1
MEN11
SLD-E1
EN
FB
SLD-E2
P_CONT3
IC622
BH2210FV-E2
MEN12
P_CONT1
CHANGER CONTROLLER2
MEN13
SLD-E3
P_CONT2
MEN20
ELV-E0
P_CONT2
MEN21
ELV-E1
SW1-A
OCSW
R635
10k
MEN22
ELV-E2
(Page
47)
IODO
MEN23
ELV-E3
E4V
IODI
A-GND
A5V
C533
0.1
D-GND
SW3.3V
CN501
19P
FL_RESET
FL_RST
R521 100
CN505
5P
LED_LATCH
LED LATCH
6V
SW+5V
S
3.3V
E3.3V
DGND
DGND
R577
47k
C510
0.1
SW+9V
R526 1k
SIRCS
SIRCS
R592
2.2k
DGND
R530 100
FL_CLK
MGND
Q502
2SA1235TP-1EF
R533 100
FL_CS
R535 100
R580
4.7k
FL_DATA
FL_DATA
KEY0
KEY0
N.C.
NOISE
(FOR LED)
GND
PWM_OUT
Q501
RT1N141C
VIN
C509
1
SCO/CLK1
R584 100
SOD/RXD1
R585 100
SID/TXD1
R586 100
BUSY/RTS1
R587 100
XIFCS
R588 100
MTRST
R589 100
IFSCK
CONT
XAMUTE
C516
1
R537
0
IFSDO
5V
IFSDI
DGND
XIFBSY
R582 100
LED3
R583 100
LED2
R591 100
LED1
LED3(2CH STEREO)
XIFCS
LED2(WIDE SURR)
3.3V_MNT
LED1(FOCUS SURR)
XSYSRST
OCSW1/GND
A3
A4
A5
A6
A7
A8
(Page
53)
(Page
43)
DGND
VOUT
KEY2
KEY1
CN504
11P
C511
0.001
B+ SWITCH
KEY2
KEY1
Q504
RSR025N03
RIPPLE FILTER
IC502
TK11133CSCL-G
Q501,502
FL_CS
R576
1k
+3.3V REGULATOR
FL_CLK
(Page
67)
SW+3.3V
A9
HCD-X1V
52
52
(Page
40)
HCD-X1V
7-21. SCHEMATIC DIAGRAM – MAIN Section (2/6) –
• See page 72 for Waveforms.
• See page 74 for IC Block Diagrams.
• See page 81 for IC Pin Function Description.
CN507
19P
(2/6)
D-GND
RB601 100
OVERFLOW2
OVF2
OVERFLOW1
P_CONT_DSP
A_SEL1
V_SEL2
V_SEL3
A_SEL0
V_SEL1
A_SEL4
V_SEL0
MIC_SW2
DIR_DO
DIR_HCE
DIR_RST
DIR_XSTAE
SEL_SA-CD
DSP_SPIDS
DSP_RESET
R764
0
SPDIF-OUT
NS_INIT
DGND
RDS_CLK
LAT1
DIGITAL-IN
SOFT_MUTE
LAT3
LAT2
OVF1
CN508
7P
DIAG
DIAG
RB602 100
EN
RESET
LAT3
LAT3
LAT2
LAT2
LAT1
D3.3V
LAT1
DGND
R618 100
RB603 100
SHIFT
C550
0.1
R501
1k
SHIFT
SCDT
A_SEL1
SCDT
R619 100
NS_INIT
R638 10k
C518
0.1
C549 47 6.3V
R540 10k
R545 10k
R525 10k
SOFT_MUTE
R639 1k
(Page 49)
SOFT_MUTE
A_SEL0
(Page 60)
NS_INIT
R601 22
AMP_D1
R602 22
AMP_D2
R603 22
AMP_D3
R604 22
OPT-IN
AMP_BCKO
R605 22
D-GND
AMP_LRCKO
R534
10k
SW3.3V
R606 47
AMP_MCKO
D-GND
(Page 54)
D-GND
ST_CE
OVERFLOW1
OVERFLOW2
ST_CE
A_SEL0
V_SEL3
V_SEL2
V_SEL1
V_SEL0
N.C.
A_SEL4
N.C.
N.C.
MIC_SW2
VSS
N.C.
N.C.
DIR_HDOUT
DIR_HCE
DIR_RST
SEL_SA-CD
N.C.
KEY INT
DSP_RESET
R596 0
AMP_D1
ST_CLK
ST_CLK
IO_RESET
ST_DI
TUNED
TUNED
IO_DO
R523 10k
IOCLK
IO_CLK
A_SEL4
FSDLY
MIC_SW2
R594 10k
(US,CND)
R504 47k
R506 ∗
RDS_DATA
RDS_DATA
IC501
M30626MJP
-A05FPU0
R609 10k
MIC_SW2
(Page
54)
ST_DI
IO_DI
R503 10k
IODO
A_SEL4
MIC_SW
AMP_D2
WRITE CE
DRIVE_OCP(DIAG)
A_SEL3
A_SEL3
AMP_D3
ST_DO
R558 10k
IO_CE
A_SEL2
A_SEL2
ST_CE
ST_CE
IODI
A_SEL1
AMP_BCKO
C551 47p
R608 0
IORST
A_SEL1
AMP_LRCKO
A_SEL3
A_SEL3
DRIVE_RST(EN)
A_SEL0
(Page
56)
AMP_MCKO
A_SEL2
A_SEL2
ST_DO
IOCE
A_SEL0
A_SEL1
OVERFLOW2
ST_DI
ST_DI
DIR_XSTATE
OVERFLOW1
DSP_SPIDS
ST_DO
ST_DO
RDS_CLK
DIAG
ST_CLK
DAMP INIT
EN
ST_CLK
DAMP SOFT
MUTE
TUNED
TUNED
DAMP LATCH1
DAMP
LATCH3
DAMP
LATCH2
RDS_CLK
RDS_CLK
VCC
RDS_DATA
RDS_DATA
P_CONT3
P_CONT3
R528 0
OUT2DLY
P_CONT2
DESTINATION
P_CONT1
P_CONT2
P_CONT1
MTRST
MTK RST
MODEL
XIFCS
KEY2
DVD XIFCS
KEY1
LED3
FL_D_OUT/LED_DATA
OCSW
CDM_OPEN_SW
BUSY/RTS1
DVD_XIFBUSY
SCO/CLK1
SOD/RXD1
DIR_ERR
DVD_SOD
SID/TXD1
I2C_
CLK
I2C_
DATA
DVD_SID
LED2
FL_CS/STB
DVD_SCO
PWM_OUT
LED1
LED_LAT
FL_CLK/LED_CLK
22k(US,CND)
C548
47
6.3V
AC_CUT
MIC/
A.CAL
SW
DIR_ZERO
∗R506
4.7k(AEP,UK)
NMI
C506 0.1
SIRCS_IN
VCC
R508 1k
DSP_INTR
C507 0.1
DAMP_SHIFT
R502
10k
(Page 57)
DAMP_SCDT
VREF
DIR_CSFLAG
KEY0
VCC
R513 100
XIN
R514 10k
C503 0.1
VSS
C508 0.1
V_SEL3
V_SEL3
DSP_MISO
KEY0
DSP_MOSI/DIR_DIN
VSS
V_SEL2
V_SEL2
RESET
C502 0.1
XOUT
LED3
V_SEL1
V_SEL1
FL_RESET
R511 100
LED4
R509 100
R512 10k
CNVSS
R510 10k
C501 0.1
DSP_SPICLK/DIR_CLK
R505 1k
KEY1
BYTE
KEY2
V_SEL0
V_SEL0
SYSTEM CONTROLLER
A3
A4
A5
C517
0.1
R539
10k
R552
4.7k
R557
47k
R549
4.7k
R563
10k
OUT
R536
0
C515 0.1
(Page 54)
R556
47k
X501
5MHz
R579 10k
R597 10k
R532 100
A6
DSP_DIR
R562
47k
C520
0.22
GND
A7
VDD
NC
CD
RESET SIGNAL GENELATOR
Q503
2SC3052EF
(Page 52)
IC503
PST3635NR
RESET SWITCH
D501
1SS355WTE-17
R561
100k
C521
0.01
C522
0.22
C523
0.1
A8
R524 10k
C538
0.1
A2
(Page 52)
HCD-X1V
53
53
LED2
PWM_OUT
DIR_ERR
FL_CS
FL_DATA
LED1
LED_LATCH
FL_CLK
DIR_ZERO
CSFLAG
(CHASSIS)
FL_RESET
DSP_SPICLK
DSP_MISO
SIRCS
DSP_INTR
SHIFT
SCDT
A1
DSP_MOSI
R522 10k
A9
R519
10k
HCD-X1V
• See page 72 for Waveforms.
7-22. SCHEMATIC DIAGRAM – MAIN Section (3/6) –
• See page 74 for IC Block Diagrams.
(3/6)
AMP_D1
AMP_D1
AMP_D2
CN701
11P
AMP_D2
AMP_D3
AMP_D3
D FLIP-FLOP
D-GND
SI_C
D2
R702 0
BCKO
BCKO
R701
330
D-GND
VCC
SW3.3V
D-GND
SO_A
SO_A
SO_B
C704
0
SO_B
SO_C
R705
1k
SPDIF
SO_C
SWITCHING
IC705
SN74LV08APWR
D-GND
DSP_BCK
C730 C702
0.1
0.1
DSP_LRCK
SI_A
L705
0
R726
100
L703
10µH
C716
0.01
C720
100
16V
R748
220k
AMP_D3
SO_B
SO_A
SI_C
AMP_D1
SI_D
DIR_XSTAE
SI_D
SI_E
BCK
BCK
LRCK
MCK
INVERTER
C723
0.1
SI_C
LRCK
Q701
RT1P140C
VSS
SI_B
SI_E
C733
0.22
R735
100
SI_A
SI_B
AMP_D2
R734
100
C721
0.01
SO_C
DIR_HCE
R706
1k
DSP_SPICLK
DIR_RST
VDD
MCK
DSP_INTR
DSP_INT
DSP_RESET
DSP_RESET*
DIR_RERR
FB701
0
DIR_RERR
DIR_NONAU
CE(I)
CL(I)
XSEL(I)
MODE0(I)
MODE1(I)
R741 100
DI(I)
DISEL(I)
R754 100
DIR_DO
SI_B
R757 100
DIR_RERR
BCKI
R756 100
BCKO
R753 100
BCK
R755 150
R740 100
ERROR(O)
DIN0(I)
R718 100
OPT-IN
DIN1(I)
BPSYNC(O)
SW3.3V
DIN2(I)
VREF
R739
100
DIR_ERR
G
1B
4A
LPF(O)
F1(O)
C727
0.1
C724
15p
R761 100
LRCK
A-GND
(Page 57)
C725
12p
C718
47
16V
C715
0.001
D702
1SS355WTE
-17
D701
1SS355WTE
-17
SW3.3V
A-GND
R738
100
CSFLAG
AUDIO(O)
EMPHA(O)
R736 100
X701
12.288MHz
XMCK(O)
XIN(I)
XOUT(O)
R733 1M
DVDD
C722 0.1
R737 0
R728 100
R729 100
R732
1k
R730 100
3B
D-GND
C714
0.1
CSFLAG(O)
DGND
XSTATE(O)
DATA(O)
LRCK(O)
CKOUT(O)
BCK(O)
R727 100
LRCKO
A5V
F0(O)
AVDD
R725 220
R752 100
2Y
P_CONT_DSP
R708
3.3k
E4V
C729 C728
0.1
100
16V
R742
1k
A/D CONVERTER
C706
47
16V
C705
47
16V
C708
0.1
C707
0.1
R709
10k
SWITCHING
R712
10k
R711
10k
IC771
SN74LVC1G08DCKR
GND
(Page 52)
IC701
WM8782SEDS/R
R743
100
VMID
VREFGND
FORMAT
VREFP
FSAMPEN
AVDD
IWL
AGND
BCLK
AINOPR
DVDD
AINR
DGND
COM
LRCLK
AINOPL
DOUT
AINL
MCLK
M/S
+2.6V REGULATOR
R724 100
R721
220
DIR_RST
BCKI
C713
0.1
R723 100
LRCLK
R722 100
SI_E
L701
10µH
R744
10k
R745 C731
15k 0.1
OUT
GND
F2(O)
R750 220
A5V
LRCLK
3A
2B
IC703
SI-3010KM-TL
VF(O)
AGND
C732
100 16V
VCC
R746
100
0
R710
10k
(Page 56)
R731
1k
DIR_NONAU
DIR_ZERO
SI_A
LRCLK
BCKI
DIR_XSTAE
A-GND
FB703
CKOUT
MCKO
R759 100
IN
SDIN
C709 10 16V
C771
0.01
CKOUT
3Y
C719 0.1
C717
10
16V
SW2.6V
FB702
4B
4Y
C710 0.068
L704
10µH
DSP_SPICLK
2A
GND
R713 0
AGND
R751 100
1Y
DSP_MOSI
DSP_SPICLK
AMP_MCKO
R749
100
R760 100
MCK
DVDD
C712 0
C711
0.1
R758 10k
1A
DGND
IC702
LC890561W
DVDD
C737 C738
0.1
10
FB751
C752
0.1
VCC
DSP_MISO
DSP_MOSI
EN
DGND
L702
10µH
D1
DSP_MOSI
DO(O)
SPDIF(O)
R716
220
R763 100
R762
220
FB
DVDD
DGND
CKSEL0(I)
DOSEL0(I)
DOSEL1(I)
XMODE(I)
CKSEL1(I)
A /B
SI_E
FB752
0
IC704
SN74LVC257APWR
C751
0.01
SEL_SA-CD
R719 100
D-GND
DSP_SPIDS*
DSP_MISO
DATA SELECTOR
(Page
55)
DIR_NONAU
DSP_SPIDS
DIGITAL AUDIO INTERFACE RECEIVER
(Page 53)
(Page 53)
R747
100
MCKO
MCKO
D-GND
AMP_MCKO
AMP_BCKO
D
LRCKO
LRCKO
AMP_LRCKO
AMP_MCKO
GND
Q
CLK
SI_D
D3
(Page 43)
IC706
SN74LVC1G79DCKR
D1
D1
R707 10k
L-IN
FB704
0
R-IN
DSP_DIR
(Page 53)
HCD-X1V
54
54
HCD-X1V
• See page 72 for Waveforms.
7-23. SCHEMATIC DIAGRAM – MAIN Section (4/6) –
• See page 74 for IC Block Diagrams.
• See page 81 for IC Pin Function Description.
SI_A
SI_B
SI_C
SI_E
SI_D
R15
10k
C66 0.1
C64 0.1
R59 0
R60 22
R57 0
R58 0
R55 0
C61 0.1
R53 47
R56 0
DSP_BCK
DSP_LRCK
+1.2V REGULATOR
R54 22
BCK
R51 0
R52 0
C55 0.1
C52 0.1
MCK
C36 10
C50 0.1
R48 0
DIR_NONAU
R47 0
C43 0.1
C46 0.1
C42 0.1
C39 0.1
LRCK
(4/6)
R14
2k
IC1
R2
SI-3010KM-TL
10k
R4
10k
C2
0.1
FB
EN
FB2
0
IN
SW2.6V
FB1 0
C3
220
4V
SW3.3V
VDDEXT
GND
GND
VDDINT
DPSOE
DPSIA
DPSIC
DPSIB
DPSID
DPSIE
GND
VDDINT
GND
DPDVBCK
DPLRCK
DPBCK
GND
VDDINT
GND
VDDEXT
GND
DPFSCK
DPDVLRCK
VDDINT
VDDINT
SF_CE∗
C26 0.1
NONAUDIO ∗
GND
VDDINT
GND
VDDINT
GND
VDDINT
VDDINT
GND
GND
VDDINT
VDDINT
OUT
GND
D-GND
DSP_BCK
C85
10
C1
100
16V
DSP_LRCK
SO_A
SO_B
VDDINT
R64 22
SO_C
SO_C
R65 22
SO_C
SI_A
DPSOC
SI_A
C71 0.1
SI_B
GND
VDDINT
DSP_LRCK
SO_B
DPSOD
GND
DSP_BCK
SO_A
SI_B
SI_C
VDDINT
GND
SI_C
C28 0.1
SI_D
GND
VDDINT
SI_D
C73 0.1
SI_E
R66 22
SO_B
BCK
R67 22
SO_A
LRCK
DPSOB
VDDINT
DPSOA
GND
C30 0.1
R21
10k
SI_E
VDDINT
GND
C29 0.1
C7
220 4V
SPI_MAS
VDDINT
MCK
DSP_INT
PF_CE
GND
DSP_RESET∗
C25 0.01
GND
VDDINT
DSP_RESET∗
R24 1k
DSP_SPIDS∗
R25 0
C74 0.1
RESET∗
VDDINT
SPIDS∗
VDDEXT
DIR_RERR
DIR_NONAU
DSP_SPIDS∗
C75 0.1
GND
VDDINT
A18
C32 0.1
R32
10k
DSP_SPICLK
GND
DSP_MISO
C6
0.1
R26 22
SPICLK
DSP_MISO
R27 22
DSP_MOSI
R28 22
A17
DSP
IC2
ADSST-AVR-1115
MISO
GND
C76 0.1
VDDINT
MOSI
GND
A16
VDDINT
AD8
C33 0.1
C23 0.1
AD9
VDDEXT
R36 10
AVDD
AD10
AVSS
AD11
C34 0.1
C24 0.01
GND
GND
C77 0.1
VDDINT
CLKOUT
R29 22
R30 22
EMU∗
AD12
TDO
VDDEXT
C78 0.1
R20 0
TDI
R13 0
R18 0
GND
TRST∗
AD13
TCK
AD14
TMS
AD15
R16 0
R17
0
GND
ALE
CLKIN
RD∗
C9 12p
C10
8p
R35 1M
VDDINT
WR∗
AD0
AD1
GND
VDDEXT
AD2
AD3
GND
VDDINT
AD4
AD5
AD6
VDDINT
GND
VDDEXT
GNF
VDDINT
C67 0.1
C63 0.1
C62 0.1
C59 0.1
GND
C79 0.1
VDDINT
R3
0
C57 0.1
R50 0
DIR_RERR
AD7
DIR_ERR
INT_REQ
VDDEXT
GND
R49 0
DSP_INT
GND
GND
VDDEXT
VDDEXT
C49 0.1
C45 0.1
GND
VDDEXT
GND
GND
BOOTCFG0
BOOTCFG1
R45 10k
R43 10k
VDDINT
R38 10k
C40 0.1
C19
10
R41 10k
VDDEXT
CLKCFG1
CLKCFG0
XTAL
C35 0.1
X1
R23
25MHz 470
C81
220
4V
C70
10
HCD-X1V
55
55
C80
100
16V
DSP_MOSI
C11
0.1
DSP_SPICLK
BCK
LRCK
MCK
DSP_INT
DSP_RESET∗
DIR_RERR
DIR_NONAU
DSP_SPIDS∗
DSP_MISO
DSP_MOSI
DSP_SPICLK
(Page 54)
HCD-X1V
• See page 74 for IC Block Diagrams.
7-24. SCHEMATIC DIAGRAM – MAIN Section (5/6) –
(5/6)
MIC AMP
IC401
NJM4558MTE2
C406
0
(US,CND)
(AEP,UK)
R422
22k
R403
0
R409
R403
R473
2.2k
R474
3.3k
C473
10
R404
1.2k
R421
470
C420
100p
C422
47p
C412
47p
G
C421
10 16V
R423
470
R424
27k
R420
100k
R414
27k
V
R412
22k
J401
R415
C471
10
R471
1.2k
C410
100p
C413
47p
C423
47p
R413
470
R410
100k
A.CAL MIC
ECM-AC1
R470
2.2k
R472
3.3k
R411
470
C411
10 16V
+9V REUGLATOR
IC300
TA7809LS
O
C403
100
16V
C404
0.1
R401
4.7k
R402
4.7k
C304
0.1
G
A12V
I
C303
47
16V
C302
0.47
A-GND
(Page 52)
C401
47 16V
R425
0
CN303
9P(US,CND)
R433
47k
(AEP,UK)
R446
0
R416
0
R446
R416
AUDIO SELECTOR
R407
220
(AEP,UK)
IC351
MC14052 BDR2
C419 R431
22
47k
16V
VDD
FB301
0
Y2
CN401
4P
CN808
4P
R405
220k
AUDIO_L
AUDIO_L
GND
GND
R447
AUDIO IN
AUDIO_R
AUDIO_R
MIC_SW2
MIC_SW2
FB806
R447
0
A
C323
0.1
VSS
B
(AEP,UK)
C836
0.01
R448
0
R408
220
(CHASSIS)
R448
C424
22
16V
R449
R301
10k
Q305
RT1N241C-TP1
R418
Q397
RT1N241C-TP1
(US,CND)
R419
R352
100k
R311
0
R362
100k
(US,CND)
DI
ST_CLK
CLK
ST_DO
DO
CE
INVERTER
RDS_DATA
RDS_DATA
RDS_CLK
RDS_CLK
TUNED
TUNED
ST_CLK
R419
0
ST_CLK
ST_DO
ST_DO
ST_CE
ST_CE
ST_DI
ST_DI
A_SEL0
Q396
RT1N241C-TP1
A_SEL1
INVERTER
Q395
RT1N241C-TP1
R317
10k
Q301
RT1P140C-TP1
A_SEL2
MUTING
A_SEL3
A_SEL4
INVERTER
R310
0
C355
100
16V
R316 R365
10k 10k
R327
10k
C360
0.1
R-IN
Q304
RT1N441C-TP1
B
MUTING CONTROL
A
SWITCH
VEE
V
X3
R346 47k
R345 47k
22 16V
R315 47k
R308 47k
C344 22 16V
R350 47k
R349 47k
INH
LINE AMP
X0
IC360
NJM4558MTE2
Y1
X
Y3
R
R347
220
R348
220k
C343
220p
J301
6P
Y
X2
Y2
L
R337
220
R338
220k
C333
220p
R
R341
220
R342
220k
C341
220p
L
R331
220
R332
220k
C331
220p
R
R303
220
R305
220k
C307
220p
L
R304
220
R306
220k
C308
220p
VDD
Y0
C334 22 16V
R340 47k
R339 47k
C332 22 16V
R336 47k
R335 47k
C312 22 16V
R309 47k
R307 47k
R359
4.7k
R364
4.7k
R354
4.7k
R355
10k
VIDEO1
C359
0.1
C366
0.1
VIDEO2
C358
100
16V
R360 4.7k
AUDIO IN
G
X1
TV
MIC_SW2
C364
1
50V
VSS
C309
MIC_SW
R358
10k
IC350
MC14052 BDR2
(Page
53)
C356
0.1
R356
10k
AUDIO SELECTOR
C342 22 16V
BLOCK
D-GND
INVERTER
(AEP,UK)
R449
0
R300
2.2
ST_CE
R432
47k
R418
0
R302
0
R325
10k
Q302
RT1P140C-TP1
C365
22
16V
MUTING
HCD-X1V
56
R326
10k
56
ANTENNA
THE ASSEMBLED
L-CH
ST_DI
VEE
R417
0
SUPPLIED WITH
+B (9V)
L300
10µH
INH
X3
FM 75Ω
COAXIAL
(FM/AM)
R-CH
Y1
X0
R406
220k
TUNER
GND
X
R398
10k
R417
C405
100p
TUNED
C306
0.1
Y3
FB805
RDS-DATA
TUNED
X1
(US,CND)
FB804
C305
100
16V
Y
FB803
J801
RDS-CLOCK
RDS_DATA
R430
47k
Y0
X2
C402
100p
11P(AEP,UK)
RDS_CLK
A-GND
L-IN
C354
1
50V
(Page 54)
AM
HCD-X1V
7-25. SCHEMATIC DIAGRAM – MAIN Section (6/6) –
• See page 72 for Waveforms.
• See page 74 for IC Block Diagrams.
(6/6)
V_SEL0
V_SEL1
R205
75
V_SEL2
VIDEO
V_SEL3
(Page 53)
J203
VIDEO SELECTOR
VIDEO2
R204
75
C204
10
16V
IC202
NJM2235V
C220
100
16V
S VIDEO
R203
75
IN1
GND
SW1
OUT
IN2
VDD
R220
0
C217
0.1
C205
10
16V
R218
0
L202
10µH
VIDEO IN
SW2
IN3
R202
75
C216
10
16V
VIDEO
VIDEO SELECTOR
J202
IC201
NJM2235V
VIDEO1
C200
0.1
R201
75
S VIDEO
R200
75
IN1
GND
SW1
OUT
C219
100
16V
C215
0.1
C201
0.1
IN2
CN201
11P
R230 0
R217
0
VDD
CVBS
V-GND
L201
10µH
SW2
R224 0
C
IN3
C214
0.1
V-GND
R223 0
Y
VIDEO
V-GND
R229 0
CY/G
VIDEO SELECTOR
J201
C202
10
16V
MONITOR
IC200
NJM2235V
OUT
IN1
GND
SW1
OUT
V-GND
C218
100
16V
R228 0
WIDE
S VIDEO
C213
0.1
C203
10
16V
IN2
(Page 43)
CB/B
R227 1k
R226 0
CR/R
R216
0
VDD
R221
0
L200
10µH
SW2
IN3
C212
10
16V
A-GND
A5V
Y
J200
3P
COMPONENT
VIDEO AMP, 75Ω DRIVER
PB /CB
VIDEO OUT
R211
75
C207
100
16V
IC203
BH7868FS-E2
VCC2
CROUTA
R210
75
(Page 54)
C225 100 16V
C224 0.1
CROUTB
PR /CR
L203
10µH
C230 1
CRIN
C206
100
16V
GND
MUTE2
CBOUTB
C229 1
CBIN
R209
75
CBOUTA
C210
1000
6.3V
GND
GND
C228 1
SYIN
CYOUTB
CLP
R208
75
CYOUTA
C209
1000
6.3V
BIAS
GND
C227 0.1
C234 10 16V
YIN
YOUTB
C233
1 50V
YCMIX
YOUTA
R207
75
CVBSIN
C208
1000
6.3V
GND
MUTE1
VOUTB
C226 100p
C231 0.1
CIN
VOUTA
R214
10k
S2
S-DC OUT
R206
75
S1
C OUT
VCC1
C211
0.1
HCD-X1V
57
57
C236 100 16V
C232
100
16V
HCD-X1V
7-26. PRINTED WIRING BOARD – AMP Board (Component Side) –
• Semiconductor
Location
1
2
3
4
• See page 37 for Circuit Boards Location.
5
6
: Uses unleaded solder.
7
8
9
10
Ref. No. Location
E
R3357
B
R3354
C3555
R3554
R3555
R3553
C3801
D3552
C3354
A-7
Q3551
R3551
C3363
IC3350
C3376
C3034
24
C3500
IC3500
25
IC3030
R3505
R3307
R3507
R3506
R3502
R3304
48
C3040
R3066
C3324
C3325
R3302
1
37
C3326
C3350
R3301
36
R3037
R3068
R3078
C3377
C3327
R3352
C3068
R3065
C3358
R3351
12
R3075
C
13
C3304
Q3551
D3551
AMP BOARD (COMPONENT SIDE)
R3032
G-3
E-3
C-3
G-2
H-2
H-5
G-5
F-5
E-5
C-5
B-5
C-2
R3031
IC3010
IC3020
IC3030
IC3050
IC3051
IC3100
IC3150
IC3200
IC3250
IC3300
IC3350
IC3500
(CHASSIS)
A
R3035
A-6
B-6
R3034
D3551
D3552
C3277
C3313
C3276
IC3300
C3274
C3275
C3225
C3224
R3073
C3070
C3308
C3226
C3227
C3300
C3177
R3254
C3024
24
C3071
13
25
C3258
R3251
12
R3252
C3250
IC3020
36
R3201
1
37
R3204
R3202
R3207
R3024
R3025
E
C3124
R3021
C3175
C3263
IC3250
C3125
R3257
R3056
R3064
R3063
48
C3030
C3204
(Page 50)
C3254
C3174
R3069
R3067
C3067
MAIN
BOARD
CN507
R3070
R3071
J
C3176
R3072
CN3700
D
C3213
IC3200
C3208
F
C3200
(CHASSIS)
R3157
L3051
5
3
4
C3163
IC3150
R3055
C3055
C3158
C3014
R3011
R3015
IC3050
R3014
R3012
C3904
24
13
25
L3052
C3150
12
R3151
R3152
IC3010
36
R3101
1
R3102
48
C3020
R3018
IC3051 1
IC3100
C3113
R3053
R3054
L3054
L3053
C3057 5 4
R3052
C3058
FB3051
C3060
H
R3104
R3107
37
C3104
G
1
C3154
R3154
R3051
C3108
C3059
3
C3100
R3601
X3051
L3000
C3005
I
(CHASSIS)
11
1-870-021-
HCD-X1V
58
58
(11)
HCD-X1V
7-27. PRINTED WIRING BOARD – AMP Board (Conductor Side) –
1
2
3
• See page 37 for Circuit Boards Location.
4
5
6
: Uses unleaded solder.
7
8
9
• Semiconductor
Location
10
(Page 69)
Ref. No. Location
POWER
BOARD
CN903
L
AMP BOARD (CONDUCTOR SIDE)
A
CN3800
4
1
C3552
R3602
C3551
R3059
C3356
D3352
R3353
C3364
C3359
L3351
C3035
C3355
D3351
C3357
C3033
1
R3366
C3301
C3031
C3314
R3315
C3309
C3317
L3321
R3319
Q3301
E
C3318
C3127
R3326
C3126
C3036
C3303
L3302
C3323
D
C3038
L3301
C3305
R3503
C3039
R3504
C3032
R3303
R3076
R3320
C3316
E
C3306
D3302
R3074
C3315
C3312
Q3302
C3037
C3319
C3320
L3322
R3325
R3327
C3374
C3375
2
C
R3027
C3367
C3368
Q3371
R3369
R3017
R3377
E
L3372
C3501
C3351
C3366
R3376
R3060
C3353
L3352
E
C3373
CN3500
C3365
R3365
R3375
C3610
SPEAKER
R3370
Q3372
C3370
L3350
L3371
B
C3362
(CHASSIS)
C3369
C3603
EP3603
L3300
D3301
C3307
R3316
Q3272
C3270
R3277
R3275
C3266
E
C3256
C3265
C3262
L3272
R3253
D3252
C3253
L3252
R3270
15
C3269
14
C3251
C3273
R3023
C3025
C3023
C3257
R3227
C3026
C3028
C3203
C3201
L3201
C3205
D3201
C3207
R3177
C3156
C3165
R3170
Q3172
C3170
R3175
C3162
L3171
C3169
R3216
L3200
C3214
R3215
L3221
R3219
C3209
M
E
C3217
F
C3029
C3021
R3226
M3000
(FAN)
C3022
R3203
D3202
C3223
Q3221
C3002
L3202
C3216
E
C3212
R3225
C3027
C3206
C3215
R3220
C3218
CN3000
Q3222
L3222
C3219
C3220
R3266
C3052
R3153
D3152
C3153
L3152
E
C3905
C3151
C3051
C3166
C3053
C3173
R3013
C3015
R3165
C3157
C3054
D3151
L3150
L3151
C3155
R3166
C3164
C3159
C3167
E
L3172
C3168
R3176
K
C3903
R3169
Q3171
G
R3605
D3251
C3069
L3251
R3265
C3264
C3255
L3250
E
C3268
C3267
E
L3271
C3259
R3269
Q3271
R3276
POWER
BOARD
CN902
CN3900
(Page 68)
C3013
C3017
H
R3120
L3112
C3106
D3112
C3112
C3115
Q3122
R3127
R3125
C3012
C3119
C3120
L3122
R3103
C3018
C3019
C3016
C3061
C3103
E
C3101
L3055
C3011
C3116
C3056
L3100
C3105
L3111
R3115
C3129
C3114
C3109
C3118
E
C3117
L3121
Q3121
R3126
R3119
C3123
D3111
C3107
R3116
R3001
R3002
C3000
I
R3004
Q3002
Q3001
E
E
C3003
C3001
R3006
R3003
Q3000
C3604
E
EP3604
R3007
1-870-021-
(CHASSIS)
HCD-X1V
59
59
11
(11)
D3111
D3112
D3151
D3152
D3201
D3202
D3251
D3252
D3301
D3302
D3351
D3352
H-6
H-6
G-6
G-6
F-6
E-6
E-6
D-6
D-6
C-6
B-6
B-6
Q3000
Q3001
Q3002
Q3121
Q3122
Q3171
Q3172
Q3221
Q3222
Q3271
Q3272
Q3301
Q3302
Q3371
Q3372
I-8
I-8
I-7
H-3
H-3
G-3
G-3
F-3
E-3
E-3
D-3
D-3
C-3
C-3
B-3
HCD-X1V
SD
RESET
PGMUTE
NSP MUTE
SOFT MUTE
LAT2
SCDT
(1/3)
SHIFT
• See page 72 for Waveforms. • See page 74 for IC Block Diagrams..
7-28. SCHEMATIC DIAGRAM – AMP Board (1/3) –
DIGITAL POWER AMP
C3356
0.033
C3353 0.1
R3060
10k
R3353 10
R3354 0
R3059
10k
C3035
0.1
C3034
0.1
R3357 15k
R3031
470
C3354
0.1
STREAM PROCESSOR
R3065 1k
SD
DIAG
R3066 100
RESET
SFLAG
XOVSS
DVSS
DVDD
XOVDD
SCDT
XFSOOUT
OVF1
NSPMUTE
R3032 470
PGMUTE
OVF
SOFTMUTE
OVF2
SCSHIFT
R3063 1k
R3064 1k
OVF2
SCLATCH
D-GND
OVFFLAGR
C3350 0.1
C3071
0.1
FLAGLOVF
CN3700
19P
R3365 10
L3350
R3351
100
VSSL
C3067 100p
LAT3
VDDL
INIT
R3068 100
C3068 100p
LAT2
R3069 100
C3069 100p
LAT3
LAT2
LAT1
LAT1
SHIFT
R3070 100
C3351 10
R3366 10
C3355 0.1
OUTL1
C3033 0.1
INIT
RESET
R3067 100
10µH
R3352
100
VSSL
LRCK
R3035 330
BCK
BCK
DATA2
OUTR1
C3032 0.1
C3306
0.033
R3302
100
R3071 100
SCDT
BFVDD
VDDR
R3072 100
SOFT MUTE
BFVSS
OUTR2
C3303 0.1
TEST
VSSR
R3303 10
DVDD
VSUBC
INIT
XFSOIN
XVDD
HPVDDL
HPOUTL2
HPOUTL1
HPVSSL
R3504 10
HPVDDR
R3505 10
AMP_D3
HPOUTR1
AMP_D2
FSOCKO
XFSIIN
R3506 10
FSOI
R3037 150
HPVSSR
R3507 10
AMP_D1
HPOUTR2
C3037 0.1
NS_INIT
R3304 0
XVSS
C3031
100
25V
AMP_BCKO
R3503 10
R3307 15k
AMP_LRCKO
R3502 10
AMP_MCKO
D-GND
C3304
0.1
R3078
0
C3025
0.1
C3038
0.1
C3039
0.1
C3040
0.1
C3300 0.1
R3056
100
R3315 10
C3024
0.1
NSP MUTE
PGMUTE
SOFT MUTE
SCDT
LAT3
SHIFT
L3300 10µH
C3301 10
R3316 10
C3305 0.1
C3256
0.033
C3253 0.1
R3253 10
R3601
0
R3257 15k
VSSL
OUTL1
C3023 0.1
INIT
INIT
VDDL
MCKSEL
A3
R3252
100
XOVSS
XFSOOUT
XOVDD
DVSS
DVDD
NSPMUTE
SCDT
PGMUTE
SFLAG
SOFTMUTE
SCSHIFT
SCLATCH
OVFFLAGR
FLAGLOVF
C3604
0.1
A2
LRCK
R3024 100
BCK
R3025 330
DATA3
C3254
0.1
R3201
100
OUTL2
LRCK
VSSL
BCK
VSSR
IC3020
CXD9876R
DATA
R3251
100
OUTR1
C3026 0.1
C3251 10
C3022 0.1
A4
BFVDD
VDDR
A5
BFVSS
OUTR2
A6
TEST
VSSR
DVDD
VSUBC
R3265 10
R3202
100
L3250 10µH
C3250 0.1
R3266 10
(Page
61)
XFSOIN
XVDD
HPVDDL
HPOUTL1
HPVSSL
HPOUTL2
HPVDDR
HPOUTR1
HPVSSR
FSOCKO
FSOI
A10
XFSIIN
R3027 150
A9
HPOUTR2
C3027 0.1
A7
A8
R3370
2.7
C3364
1
D3351
P6SMB39AT3
L3351
10µH
R3369
2.7
C3368
0.0022
C3367
0.0022
C3358
0.1
C3366
2200
35V
C3359
100
35V
C3313
0.1
C3312
100
35V
C3320
0.0022
L3302
10µH
D3302
P6SMB39AT3
B1
C3315
1
C3319
0.0022
R3320
2.7
C3314
1
D3301
P6SMB39AT3
L3301
10µH
R3319
2.7
C3318
0.0022
B2
B3
B4
B5
B6
B7
(Page
62)
C3317
0.0022
C3308
0.1
C3309
100
35V
C3316
2200
35V
C3255 0.1
XVSS
C3021
100
25V
IC3250
CXD9883M
BST
_A
PVDD_A
GVDD_A
PVDD_A
/OTW
PVDD_A
/SD
GND
/RESET
GND
PWM_A
GND
OC_ADJ
OUT_A
GND
OUT_A
GND
OUT_A
VREG
OUT_B
M3
OUT_B
M2
OUT_B
M1
GND
PWM_B
GND
VDD
GND
GND
PVDD_B
GVDD_B
PVDD_B
BST_B
PVDD_B
R3254 0
A1
C3369
0.0022
DIGITAL POWER AMP
R3021
470
STREAM PROCESSOR
(CHASSIS)
C3365
1
C3307
0.033
OVF2
R3023
10k
EP3604
L3352
10µH
IC3300
CXD9883M
BST
_A
PVDD_A
GVDD_A
PVDD_A
/OTW
PVDD_A
/SD
GND
/RESET
GND
PWM_A
GND
OC_ADJ
OUT_A
GND
OUT_A
GND
OUT_A
VREG
OUT_B
M3
OUT_B
M2
OUT_B
M1
GND
PWM_B
GND
VDD
GND
GND
PVDD_B
GVDD_B
PVDD_B
BST_B
PVDD_B
SOFT_MUTE
R3605
0
D3352
P6SMB39AT3
R3301
100
VSSR
IC3030
CXD9876R
DATA
SCDT
(Page 53)
C3370
0.0022
DIGITAL POWER AMP
C3036 0.1
C3070 0.001
C3362
100
35V
R3034 100
LRCK
SHIFT
R3073 100
C3363
0.1
C3357
0.033
OUTL2
MCKSEL
IC3350
CXD9883M
BST
_A
PVDD_A
GVDD_A
PVDD_A
/OTW
PVDD_A
/SD
GND
/RESET
GND
PWM_A
GND
OC_ADJ
OUT_A
GND
OUT_A
GND
OUT_A
VREG
OUT_B
M3
OUT_B
M2
OUT_B
M1
GND
PWM_B
GND
VDD
GND
GND
PVDD_B
GVDD_B
PVDD_B
BST_B
PVDD_B
C3263
0.1
C3262
100
35V
C3270
0.0022
L3252
10µH
D3252
P6SMB39AT3
C3265
2.2
C3269
0.0022
R3270
2.7
R3269
2.7
C3264
2.2
L3251
10µH
D3251
P6SMB39AT3
C3268
0.0022
C3267
0.0022
C3258
0.1
C3259
100
35V
C3266
2200
35V
C3257
0.033
A11
A15
A12
A16
A13
A17
A14
A18
A19
A20
A21
C3028
0.1
C3029
0.1
C3030
0.1
HCD-X1V
60
60
(Page
61)
HCD-X1V
7-29. SCHEMATIC DIAGRAM – AMP Board (2/3) –
• See page 72 for Waveforms. • See page 74 for IC Block Diagrams.
(2/3)
A21
A20
A19
A18
A17
C3015
0.1
NSP MUTE
SCDT
PGMUTE
SOFT MUTE
LAT1
SHIFT
A9
A16
A15
C3014
0.1
R3055
100
DIGITAL POWER AMP
C3206
0.033
IC3200
CXD9883M
(Page
60)
A14
C3203 0.1
BST
_A
PVDD_A
GVDD_A
PVDD_A
/OTW
PVDD_A
/SD
GND
/RESET
GND
PWM_A
GND
OC_ADJ
OUT_A
GND
OUT_A
GND
OUT_A
VREG
OUT_B
M3
OUT_B
M2
OUT_B
M1
GND
PWM_B
GND
VDD
GND
GND
PVDD_B
GVDD_B
PVDD_B
BST_B
PVDD_B
A10
R3203 10
OVF
R3011
470
R3204 0
STREAM PROCESSOR
INIT
SFLAG
XOVSS
XOVDD
XFSOOUT
DVSS
DVDD
SCDT
PGMUTE
SCSHIFT
NSPMUTE
R3013
10k
SOFTMUTE
A12
SCLATCH
FLAGLOVF
R3012 470
A13
OVFFLAGR
R3207 15k
C3204
0.1
R3151
100
VSSL
OUTL1
C3013
VDDL
INIT
R3014 100
BCK
R3015
C3201 10
VSSL
LRCK
R3215 10
330
BCK
DATA1
R3101
100
VSSR
IC3010
CXD9876R
DATA
OUTR1
OUTR2
TEST
VSSR
DVDD
VSUBC
10µH
C3200 0.1
0.1
R3102
100
C3205 0.1
XFSOIN
XVDD
HPVDDL
HPOUTL1
HPVSSL
HPOUTL2
HPVDDR
HPOUTR1
FSOI
XFSIIN
FSOCKO
R3017 150
XVSS
C3156
0.033
C3011
100
25V
C3153 0.1
R3157 15k
R3018
0
A7
C3018
0.1
C3019
0.1
A11
R3054
100
C3020
0.1
C3154
0.1
A6
C3056
47
63V
A5
A4
R3052
1M
C3057
0.01
R3053
100
C3151 10
A2
OSC BUFFER
X3051
49.152MHz
R3165 10
IC3051
SN74AHC1GU04DCKR
C3060
10p
NC
C3150 0.1
V
L3053
10µH
C3059
0.001
C3155 0.1
L3054
1µH
R3219
2.7
D3201
P6SMB39AT3
L3201
10µH
C3214
2.2
C3218
0.0022
C3217
0.0022
C3208
0.1
C3209
100
35V
C3163
0.1
C3162
100
35V
C3216
2200
35V
C3170
0.0022
D3152
P6SMB39AT3
L3152
10µH
C3169
0.0022
C3165
1
C2
C3
R3170
2.7
D3151
P6SMB39AT3
C4
C5
R3169
2.7
C3164
1
C6
C3168
0.0022
L3151
10µH
C7
C8
C3167 0.0022
C3158
0.1
C3159
100
35V
(Page
62)
C3166
2200
35V
FB3051
0
L3055
10µH
R3007
0
R3220
2.7
C3157
0.033
G
B+ SWITCH
(FOR FAN MOTOR)
L3000
10µH
L3150 10µH
R3166 10
C3058
10p
Q3000
2SD1616-TP-LK
C3002
0.1
C3219
0.0022
C3215
2.2
IC3150
CXD9883M
BST
_A
PVDD_A
GVDD_A
PVDD_A
/OTW
PVDD_A
/SD
GND
/RESET
GND
PWM_A
GND
OC_ADJ
OUT_A
GND
OUT_A
GND
OUT_A
VREG
OUT_B
M3
OUT_B
M2
OUT_B
M1
GND
PWM_B
GND
VDD
GND
GND
PVDD_B
GVDD_B
PVDD_B
BST_B
PVDD_B
A8
CN3000
2P
D3202
P6SMB39AT3
C3207
0.033
R3153 10
A1
C3220
0.0022
L3202
10µH
DIGITAL POWER AMP
R3154 0
A3
C3212
100
35V
0.1
HPVSSR
C3017
VDDR
BFVSS
0.1
HPOUTR2
(Page
60)
BFVDD
L3200
R3216 10
C3012
C3016
R3152
100
OUTL2
MCKSEL
LRCK
0.1
C3213
0.1
DIGITAL POWER AMP
M3000
C3000
100
16V
(FAN)
C3106
0.033
R3006
2.2k
C3103 0.1
R3103 10
C3005
0.1
R3004
1.2k
R3003
1.5k
R3104 0
IC3500
SN74LVC541
(CHASSIS)
BUFFER
L3052
10µH
Q3001
2SC3052EF-T1-LEF
R3074 100
DATA1
R3075 100
DATA2
R3076 100
DATA3
R3107 15k
BCK
FG
C3905
0.1
13V
3.3V
12V
GND
C3104
0.1
LRCK
R3001
10k
C3001 47 16V
CN3900
7P
C3003 0.1
(Page
71)
C3101 10
R3115 10
C3903
0.1
C3061
220 16V
GND
C3904
0.1
L3100 10µH
C3501 C3500
100 16V 0.1
R3002
10k
C3100 0.1
R3116 10
C3105 0.1
Q3002
2SC3052EF-T1-LEF
IC3100
CXD9883M
BST
_A
PVDD_A
GVDD_A
PVDD_A
/OTW
PVDD_A
/SD
GND
/RESET
GND
PWM_A
GND
OC_ADJ
OUT_A
GND
OUT_A
GND
OUT_A
VREG
OUT_B
M3
OUT_B
M2
OUT_B
M1
GND
PWM_B
GND
VDD
GND
GND
PVDD_B
GVDD_B
PVDD_B
BST_B
PVDD_B
C3113
0.1
C3112
100
35V
C3120
0.0022
D3112
P6SMB39AT3
L3112
10µH
C3119
0.0022
C3115
1
R3120
2.7
R3119
2.7
C3114
1
D3111
P6SMB39AT3
C3118
0.0022
L3111
10µH
C3117
0.0022
C3108
0.1
C3109
100
35V
C3116
2200
35V
32V
32V
P-GND
C3107
0.033
C3052
100
16V
Q3001,3002
FAN MOTOR DRIVE
C3054
100
16V
C1
C3055
0.01
IC3050
TK11118CSCL-G
NOISE
VOUT
C3801
0.1
L3051
10µH
C3053
0.001
C3051
0.1
GND
VIN
(Page
62)
+1.8V REGULATOR
CONT
R3051
0
HCD-X1V
61
61
CN3800
4P
P-GND
(Page
71)
HCD-X1V
7-30. SCHEMATIC DIAGRAM – AMP Board (3/3) –
(3/3)
SD
Q3551
2SC3052EF
-T1-LEF
PROTECT DETECT
R3554
100k
C3555
0.1
R3555
0
EP3603
C3610 0.1
Q3302
2SA1235TP-1EF
Q3372
2SA1235TP-1EF
Q3222
2SA1235TP-1EF
Q3272
2SA1235TP-1EF
OVER LOAD DETECT
OVER LOAD DETECT
OVER LOAD DETECT
OVER LOAD DETECT
Q3301
2SA1235TP-1EF
Q3371
2SA1235TP-1EF
Q3221
2SA1235TP-1EF
Q3271
2SA1235TP-1EF
OVER LOAD DETECT
OVER LOAD DETECT
OVER LOAD DETECT
OVER LOAD DETECT
R3326
100k
C3603 0.1
R3602
0
C3323
2.2
C3373
2.2
C3223
10
C3273
10
R3327
100k
R3377
100k
R3227
100k
R3277
100k
R3325
100k
R3376
100k
R3375
100k
R3226
100k
B1
R3225
100k
(CHASSIS)
CN3500
15P
SPEAKER
R3276
100k
R3275
100k
GND
REAR RCH+
L3321
C3326
0.01
C3327 0.001
L3372
C3376
0.01
C3377 0.001
REAR LCH-
L3322
C3324
0.01
C3325 0.001
REAR RCH-
L3371
C3374
0.01
C3375 0.001
REAR LCH+
L3271
C3276
0.01
C3277 0.001
SW+
L3272
C3274
0.01
C3275 0.001
SW-
L3221
C3224
0.01
C3225 0.001
SW+
L3222
C3226
0.01
C3227 0.001
SW-
L3122
C3126
0.01
C3127 0.001
FRONT RCH-
L3171
C3176
0.01
C3177 0.001
FRONT LCH+
L3121
C3124
0.01
C3125 0.001
FRONT RCH+
L3172
C3174
0.01
C3175 0.001
FRONT LCH-
B5
B3
B4
B2
B7
(Page
60)
B6
C3
C2
C6
C4
C7
C5
C8
R3553
10k
C3552
10
50V
D3551
1SS355WTE-17
D3552
1SS355WTE-17
(Page
61)
R3551
100k
C3551
1
50V
R3126
100k
R3176
100k
R3125
100k
R3127
100k
R3177
100k
C3123
2.2
C3173
2.2
R3175
100k
Q3122
2SA1235TP-1EF
Q3172
2SA1235TP-1EF
OVER LOAD DETECT
OVER LOAD DETECT
Q3121
2SA1235TP-1EF
Q3171
2SA1235TP-1EF
OVER LOAD DETECT
OVER LOAD DETECT
C1
(Page
61)
HCD-X1V
62
62
HCD-X1V
• See page 81 for IC Pin Function Description.
S810
S809
S808
DISC 3
DISC 4
DISC 5
DISC 3
DISC 4
DISC 5
(AMBER)
(GRN)
Q8
R830
220
Q9
R831
220
LED DRIVER
(AMBER)
(GRN)
R829
220
(AMBER)
R828
220
(GRN)
R827
220
(AMBER)
R826
220
(GRN)
R825
220
R824
220
IC802
BU2099FV1
C818 220p
Q5
C823 220p
Q4
Q5
Q4
Q6
Q3
Q7
Q2
Q8
Q1
Q9
Q0
C819 220p
Q6
C824 220p
Q3
C820 220p
Q7
C825 220p
Q2
C821 220p
Q8
C826 220p
Q1
C822 220p
Q9
C827 220p
Q0
C806 470p
CN807
8P
Q10
LCK
Q11
CLK
C817 220p
C816 220p
R812
0
GND
SO
KEY1
OE
6V
VDD
DATA
NC
VSS
C833
0.1
DGND
3.3V
R818 100
FL_DATA
R819 100
(Page
67)
FL_CLK
R813 100
LED LATCH
S802
S803
S805
+
VOLUME
-
S801
R853
2.2k
S804
R862
2.2k
FUNCTION
S806
CN804
4P
CN805
2P
DGND
KEY1
KEY0
CN806
2P
R852
2.2k
KEY2
(Page
67)
HCD-X1V
63
63
(AMBER)
(GRN)
R823
220
R822
220
Q0
S811
DISC 2
DISC 2
Q1
S807
S812
DISC 1
DISC 1
R855
2.2k
Q2
R856
2.2k
D815
SML-020MDT
Q3
R857
4.7k
D814
SML-020MDT
Q4
R858
10k
D813
SML-020MDT
Q5
R859
22k
D812
SML-020MDT
Q6
R860
47k
D811
SML-020MDT
Q7
7-31. SCHEMATIC DIAGRAM – KEY Section –
HCD-X1V
7-32. PRINTED WIRING BOARD – LED Board – • See page 37 for Circuit Boards Location.
1
2
3
4
: Uses unleaded solder.
5
6
7
8
9
10
11
12
LED BOARD (COMPONENT SIDE)
A
R813
(GRN)
R830
(AMBER)
R831
D811
DISC 1
(GRN)
(GRN)
(GRN)
(GRN)
(AMBER)
(AMBER)
(AMBER)
(AMBER)
D812
DISC 2
D813
DISC 3
D815
DISC 5
D814
DISC 4
R828
R829
R819
R826
R824
R827
R825
C806
R822
R823
B
10
1
C817
C816
(Page
66)
C833
IC802
11
R818
CN807
N
DISPLAY BOARD
CN803
20
11
C
1-870-016-
(11)
1-870-016-
(11)
LED BOARD (CONDUCTOR SIDE)
C821
C827
D
C825
R812
C819
C823
C822
C818
C826
C824
S811
S812
R859
C820
R860
DISC 1
DISC 3
DISC 4
S807
R855
R856
R857
R858
DISC 2
S808
S809
S810
DISC 5
Z
11
S807 – 812
E
• Semiconductor
Location
Ref. No. Location
HCD-X1V
64
64
D811
D812
D813
D814
D815
B-2
B-4
B-5
B-7
B-8
IC802
B-10
HCD-X1V
7-33. PRINTED WIRING BOARDS – KEY/POWER-SW Boards –
1
2
3
4
5
6
• See page 37 for Circuit Boards Location.
7
8
9
10
: Uses unleaded solder.
11
12
13
14
15
16
17
18
19
20
21
22
KEY BOARD (COMPONENT SIDE)
POWER-SW BOARD (COMPONENT SIDE)
A
B
S801
N
S806
1
S804
x
S805
–
S803
FUNCTION
S802
+
VOLUME
C
11
11
1-870-018-
(11)
1-870-017-
(11)
S801 – 806
D
POWER-SW BOARD (CONDUCTOR SIDE)
KEY BOARD (CONDUCTOR SIDE)
E
R852
R862
R853
F
(Page
66)
CN806
2
2
G
CN805
1
M
CN804
1
DISPLAY
BOARD
CN802
11
1-870-018-
(11)
1-870-017-
11
(11)
HCD-X1V
65
65
HCD-X1V
• See page 37 for Circuit Boards Location.
7-34. PRINTED WIRING BOARD – DISPLAY Board –
1
2
3
4
5
: Uses unleaded solder.
6
7
8
9
10
11
12
(Page 50)
MAIN BOARD
CN501
C814
D818
D819
R861
R854
R851
D803
E
E
R869
R817
R815
C813
R846
C811
C812
R820
FB802
Q817
C810
L802
E
R868
R814
L803
L804
R816
B
D817
Q818
C815
E
R875
Q819
Q802
R867
R805
C808
C809
C829
CN801
FB801
R872
A
G
DISPLAY BOARD (COMPONENT SIDE)
C805
R801
R802
C
CN803
N
LED
BOARD
CN807
11
(Page 64)
D
1-870-015-
(11)
1-870-015-
(11)
(CHASSIS)
E
DISPLAY BOARD (CONDUCTOR SIDE)
EB807
C802
D801
D804
D802
D805
L801
9
1
2
4
51
53
54
1
8
2
T801
3
INVERTER
TRANSFORMER
5
6
7
4
C801
C800
4
C803
C804
1
Q801
F
5 3 2
FL801
FLUORESCENT INDICATOR
TUBE
R804
IC803
IC801
C828
3
1
4
CN802
1
R821
G
11
BOARD
M KEYCN804
• Semiconductor Location
HCD-X1V
66
66
(Page 65)
Ref. No. Location
Ref. No. Location
D801
D802
D803
D804
D805
D817
D818
D819
IC801
IC803
F-2
G-7
Q801
Q802
Q817
Q818
Q819
F-11
B-7
B-10
B-10
B-10
E-9
E-9
B-9
E-10
E-10
B-10
B-10
B-10
HCD-X1V
• See page 72 for Waveforms.
7-35. SCHEMATIC DIAGRAM – DISPLAY Board –
• See page 74 for IC Block Diagrams.
FL801
FLUORESCENT INDICATOR TUBE
REMOTE CONTROL
RECEIVER
IC801
NJL23H400A
CN802
4P
KEY1
R851 1k
KEY0
R861 1k
KEY2
FL
FL
NP
P36
P37
P35
P34
P33
P32
P31
P30
P29
P28
P27
P26
P25
P24
P23
P22
P21
P20
P19
P18
P17
P16
P15
P14
P13
P12
P11
P10
P9
P8
P7
P6
P5
P3
P4
P2
P1
11G
10G
9G
8G
7G
5G
6G
4G
3G
2G
1G
NP
FL
FL
DGND
R854 1k
CN803
8P
(Page 63)
DGND
S37
S36
S35
S34
S33
S32
S31
S30
S29
S28
S27
S26
S25
S24
S23
S22
S21
S20
S19
S18
S17
S16
S15
S14
S13
S12
S11
S10
S9
S8
S7
S6
S5
S4
S3
S2
S1
G11
G10
G8
G9
G7
G6
G5
G4
G2
G3
G1
KEY1
6V
C829
47
6.3V
DGND
3.3V
C828
0.01
FL_DATA
FL_CLK
R821
47
LED LATCH
FB801
0
CN801
19P
(Page
63)
LED1(FOCUS SURR)
C813 100p
C812 100p
C810 0.01
C811 0.0022
R820 10k
C808 0.01
FOCUS
WIDE
LED2(WIDE SURR)
2CH
LED3(2CH STEREO)
DGND
5V
L804 0
KEY0
R817 100
L803 0
R816 100
L802 0
KEY1
G11
G10
G9
G8
G7
G6
G5
G4
G3
G2
G1
S36
S35
S34
S33
S32
S30
S31
KEY2
R815 100
FL_DATA
R846 100
FL_CS
FB802
R875
100k
0
FL_CLK
C814 0.1
GRID DRIVE
C809
47p
C815 10
DGND
Q802
2SC3052EF
-T1-LEF
SIRCS
R801
33k
DGND
E3.3V
3.3V
C805
0.1
R814
3.3k
6V
LED LATCH
R872
1k
D803
UDZS-TE17
-6.2B
FL_RST
R802
100
C802
47 50V
D817
SEC1201C
D818
SEC1201C
FOCUS
WIDE
2CH
SUR
SUR
STEREO
DRIVER
P1
AD2
P2
AD1
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20
S21
S22
S23
S24
S25
S26
S28
S27
IC803
ML9208-03MBZ03B
Q817
RT1N141C-TP-1
D804 1SS355TE-17
FLUORESCENT
INDICATOR TUBE
D805 1SS355TE-17
VDD
CLK
DAT
CS
RST
OSC1
GND
OSC0
VFL
G16
G15
G14
G13
G12
G11
G9
G10
G8
G7
G6
G4
G5
G3
G2
G1
S35
S34
S33
S32
S29
S30
S31
C804
0.01
R867
150
Q818
RT1N141C-TP-1
LED DRIVE
R868
150
LED DRIVE
D819
SEC1201C
Q819
RT1N141C-TP-1
R869
150
LED DRIVE
FOCUS
D802
1SS355TE-17
WIDE
2CH
D801
1SS355TE-17
S37
S2
S1
S3
S4
S5
S6
S7
S8
S10
S9
S11
S12
S13
S14
S15
S16
S18
S17
S20
S19
S21
S22
S23
S24
S25
S27
S26
S28
S29
T801
INVERTER TRANSFORMER
6
Q801
CPH5504
5
OSC
9
R805
0
C803
100
10V
HCD-X1V
67
67
1
C800
0.0047
C801
0.022
L801
47mH
R804
3.9k
(Page
52)
HCD-X1V
• See page 37 for Circuit Boards Location.
7-36. PRINTED WIRING BOARD – POWER Board (Component Side) –
• Semiconductor
Location
1
2
3
4
5
6
: Uses unleaded solder.
7
8
9
10
Ref. No. Location
D906
D923
D924
D935
I-8
F-6
F-6
F-5
IC507
C-3
A
(CHASSIS)
B
POWER BOARD (COMPONENT SIDE)
C
1
C966
IC507
R915
5
H
MAIN
BOARD
CN506
(Page
51)
L935
C919
R918
D
L948
CN904
L934
C923
E
L932
R911
F
(Page
59)
K
R949
R923
D923
CN902
D924
R925
R953
AMP
BOARD
CN3900
D935
C912
G
R916
R934
(CHASSIS)
R939
R965
R932
R931
H
I
C907
R906
D906
J
(CHASSIS)
11
1-870-020-
HCD-X1V
68
68
(11)
HCD-X1V
• See page 37 for Circuit Boards Location.
7-37. PRINTED WIRING BOARD – POWER Board (Conductor Side) –
1
2
3
4
5
6
: Uses unleaded solder.
7
8
9
• Semiconductor
Location
10
Ref. No. Location
POWER BOARD (CONDUCTOR SIDE)
A
Q
LF
BOARD
CN905
B
2
C913
CN906
(Page
70)
1
C902
C
D901
4
T902
SUB POWER
TRANSFORMER
1
C918
16
C946
R946
R969
R958
R957
R945
C920
C954
C968
R929
IC901
IC921
IC931
IC951
F-3
E-5
G-9
F-8
PC901
PC902
PC903
F-7
F-7
F-7
Q904
Q921
Q943
H-2
F-5
G-8
D903
D942
C925
C944
C904
R927
D
C982
IC921
1
C981
C967
D943
C958
C979
3
C980
C940
D944
R912
C929
R922
C903
7
C977
8
6
E
D941
D922
8
C928
C960
R914
C922
C978
C941
C915
E
C
Q921
E
A
PC902
K
R956
L937
D925
R926
PC903
C924
IC901
D909
R928
E
C
R908
C910
4
R910
E
3
K
A
PC901
1
IC951
C947
R954
R951
1
2
L936
R955
A
C952
C
C955
R952
C909
F
C948
K
R909
C911
C937
5
R933
R935
R936
C938
3
1
IC931
C906
G
R967
T901
MAIN POWER
TRANSFORMER
C905
Q904
E
L931
E
Q943
D913
H
C-2
C-5
J-4
I-4
I-4
F-6
G-3
J-4
I-4
E-5
F-5
I-8
E-8
D-8
D-8
E-8
C921
C976
1
D901
D903
D905
D907
D908
D909
D913
D914
D915
D922
D925
D931
D941
D942
D943
D944
1
C914
C908
C934
C933
11
A
C935
K
D931
C939
A
C936
R919
R903
I
CN903
D907
C932
D908
6
7
D915
D905
C917
R905
D914
J
11
1-870-020BOARD
L AMPCN3800
(Page 59)
HCD-X1V
69
69
(11)
HCD-X1V
7-38. PRINTED WIRING BOARD – LF Board –
1
2
• See page 37 for Circuit Boards Location.
3
4
: Uses unleaded solder.
5
6
7
LF BOARD (COMPONENT SIDE)
A
(CHASSIS)
(CHASSIS)
B
C
D
1-870-019-
11
(11)
LF BOARD (CONDUCTOR SIDE)
E
1
F
FH901
FH902
Q
CN905
POWER
BOARD
CN906
F901
2
2
(Page
69)
1
CN901
TH901
VDR901
C916
G
LF901
LINE
FILTER
C901
(AC IN)
(US, CND)
C962
R901
C963
R902
C964
H
C961
11
(AEP, UK)
1-870-019-
HCD-X1V
70
70
(11)
HCD-X1V
• See page 74 for IC Block Diagrams.
7-39. SCHEMATIC DIAGRAM – POWER SUPPLY Section –
∗C905
F901
CN901
2P
LIVE
8A 125V(US,CND)
LF901
T6.3AH 250V(AEP,UK)
NUTRAL
VDR901
C901
0.22
275V
0.01 400V(US,CND)
D901
D5SBA60F01
CN906
2P
C920
0.01
250V
R901
1M
1/2W
C916
0.0047
250V
2
C964
330p
125V
C962
680p
125V
T901
18k 3W(US,CND)
MAIN POWER
D931
FCU20UC20
470p 125V(AEP,UK)
TRANSFORMER
47k 3W(AEP,UK)
4
1
1
C902
0.22
275V
R903
11
C905
∗
10
∗
C903
C961
680p
125V
C918
0.01
250V
(AEP,UK)
(US,CND)
330p 125V(US,CND)
∗R903
3
R902
3.3M
1/2W
C938
0.0033 400V(AEP,UK)
TH901
LINE FILTER
C963
330p
125V
(AC IN)
CN905
2P
D913
SARS03
1000 200V(US,CND)
330 400V(AEP,UK)
C934
R932 R965 R931 2200
33k 3.3k 4.7k
35V
R939
3.3k
8
7
C906
∗
R905
10
C936
0.1
6
C935 0.1
D905
D1NL20U-TR2
D908
1SS355WTE
Q904
RT1P141C
POWER CONTROL
B+ SWITCH
CN903
4P
C933 2200 35V
P-GND
1000p 1.5kV(AEP,UK)
D914
1SS355WTE
32V
L931
10.8µH
PC901
TLP421F(D4-GR)
D915
UDZW10B
D906
1SS355WTE
C939
0.1
C932 2200 35V
∗C906
3300p 1.5kV(US,CND)
32V
P-GND
R934
1k
ISOLATOR
IC901
R906
3.3k
R919
18k
D907
1SS355WTE
STR-F6138-LF1352(US,CND)
STR-F6168-LF1352(AEP,UK)
R935
1k
C937
0.047
R933
4.7k
Q943
RT1N144C
C917
0.1
(Page 61)
MAIN POWER ON/OFF
SWITCH
FB/OLP
R910
2.2k
VCC
C908
47
50V
D
R936
470k
R909
100k
C911
0.0047
R949
1k
C914
1
50V
OCP/SYNC
C909
220p
R914
C907
0.0015(US,CND)
0.1 5W(AEP,UK)
PC903
TLP421F(D4-GR)
ISOLATOR
0.001(AEP,UK)
R911
220
0.05 5W(US,CND)
C910
47
50V
R967
1k
IC931
TA76431AS
(TE12L)
GND
SHUNT REGULATOR
R908
3.3k
D909
1SS355WTE
R957
68k
R912
0.22 2W(US,CND)
C912
0.1
C947
0.1
0.33 2W(AEP,UK)
+9V REGULATOR
R929
2.2
1/2W
POWER CONTROL
PC902
TLP421F(D4-GR)
IC507
SI-3010KM-TL
GND
C948
0.1
GND
12V
R958
2.2k
ISOLATOR
IC921
STR-V153
CN902
6P
R916
2.2
3.3V
IN
EN
FB
R955
470
GND
OUT
STARTUP
FB/OLP
NC
GND
S.OCP
VCC
DRAIN
NC
13V
R956
1k
R928
1k
FG
R918
2.2
R946
10k
C928
C919
0.1
CN904
13P
M-GND
(Page
61)
330p 125V(US,CND)
∗C954
470p 125V(AEP,UK)
C946
1000
16V
0.01 400V(US,CND)
T902
0.0033 400V(AEP,UK)
R969
1k
Q921
2SD1616
D925
UDZW5.1B
RIPPLE FILTER
D903
ST02D-14
D923
UDZW5.1B
R923
4.7k
C913
0.01 125V(US,CND)
100p 125V(AEP,UK)
(CHASSIS)
R927
0.82 1W(US,CND)
1 1W(AEP,UK)
C924
2.2
50V
R926
680k
C915
1
50V
D924
UDZW24B
C955
0.0047
D922
D1NL20U-TR2
C922
22
100V
10µH
M+9V
C981 0.1
L948
D941
EK19LF-F7
C958
0.1
C979 0.1
C960
0.1
R954
22k
C952
0.047
L934
10µH
C980 0.1
L932
10µH
C977 0.1
12V
A-GND
C978 0.1
REGULATOR
IC951
TA76L431S
R953
3.9k
C967
0.1
C944
2200
16V
C921
0.1
C904
0.1
71
E13V
D-GND
8
HCD-X1V
E6V
P_CONT2
SHUNT
C940
2200
16V
E4_D+3.3V
D+3.3V
R951
220
L936
D943
RK36
7
C923
0.0047
C941
1000
25V
D942
RK36
5
10µH
L937
R952
2.2k
3
R922
4.7
71
E6_D+5V
16
1
D944
EK19LF-F7
C929
0.1
C982
0.1
L935
C954
∗
R925
10
C925
47p
2kV
C976
100
16V
R915
1k
D-GND
33k 2W(US,CND)
68k 2W(AEP,UK)
C966
0.1
SUB POWER TRANSFORMER
R945
D935
1SS355TE
C968
0.1
E+4V
(Page
52)
HCD-X1V
• Waveforms
– MAIN Board –
– DMB12 Board –
1
IC111 6
7
IC101 <x/x (YUV5)
(Color bar)
37 ns
8
IC101 <x/c (YUV6)
(Color bar)
500 mV/DIV, 20 µs/DIV
500 mV/DIV, 200 ns/DIV
3
IC101 <z.v (YUV1)
(Color bar)
9
IC101 <xzc (ALRCK)
500 mV/DIV, 20 µs/DIV
4
IC101 <z.n (YUV2)
(Color bar)
H
qa
IC101 <xzb (ACLK)
IC101 <x// (YUV4)
(Color bar)
IC708 qg (X1)
1.1 Vp-p
H
500 mV/DIV, 20 µs/DIV
2 V/DIV, 50 ns/DIV
IC203 wl (VOUTB),
e; (VOUTA) (Color bar)
es
IC203 qj (CROUTB),
qk (CROUTA) (Color bar)
1.5 Vp-p
81 ns
H
500 mV/DIV, 20 µs/DIV
2 V/DIV, 50 ns/DIV
HCD-X1V
72
72
2 V/DIV, 10 µs/DIV
rf
IC3051 4
1 Vp-p
2.1 Vp-p
20 ns
1 V/DIV, 20 µs/DIV
IC203 es (C OUT)
(Color bar)
1.3 Vp-p
H
3.2 Vp-p
3.8 Vp-p
eh
ej
500 mV/DIV, 20 ns/DIV
IC701 1 (MCLK)
3.4 Vp-p
1 V/DIV, 20 µs/DIV
1 Vp-p
1 V/DIV, 50 ns/DIV
wh
100 ns
IC2 <zvc (XTAL)
IC3010 ej (FSOCKO),
ek (FSOI)
21 µs
H
40 ns
81 ns
2 V/DIV, 20 ns/DIV
qs
ea
rd
2 Vp-p
2 V/DIV, 100 ns/DIV
IC702 wa (XOUT (O))
500 mV/DIV, 10 ns/DIV
IC203 wh (YOUTB),
wj (YOUTA) (Color bar)
3.4 Vp-p
2.8 Vp-p
40.6 ns
500 mV/DIV, 20 µs/DIV
6
wg
eg
326 ns
2 V/DIV, 10 µs/DIV
1.3 Vp-p
H
IC2 ij (DPDVBCK)
IC3010 qf (XFSOOUT)
20 ns
1 V/DIV, 20 µs/DIV
2 V/DIV, 10 µs/DIV
e;
rs
2 Vp-p
3.4 Vp-p
IC702 qg (LRCK (O))
4 Vp-p
1.3 Vp-p
H
IC2 ih (DPDVLRCK)
3.4 Vp-p
2 V/DIV, 100 ns/DIV
IC203 wd (CYOUTB),
wf (CYOUTA) (Color bar)
21 µs
21 µs
326 ns
500 mV/DIV, 20 µs/DIV
IC101 <z., (YUV3)
(Color bar)
wf
4 Vp-p
1 Vp-p
5
IC101 <xzv (ABCK)
ef
500 mV/DIV, 10 ns/DIV
H
3.4 Vp-p
2 V/DIV, 100 ns/DIV
1.3 Vp-p
500 mV/DIV, 20 µs/DIV
2 V/DIV, 100 ns/DIV
326 ns
2 V/DIV, 10 µs/DIV
q;
IC701 6 (BCLK)
IC3020 qf (XFSOOUT)
20 ns
3.4 Vp-p
wl
ra
1.5 Vp-p
326 ns
IC702 qf (BCK (O))
4 Vp-p
20.8 µs
H
wk
2 V/DIV, 50 ns/DIV
wd
1.1 Vp-p
IC702 qd (CKOUT (O))
81 ns
H
IC203 w; (CBOUTB),
wa (CBOUTA) (Color bar)
H
2 V/DIV, 10 µs/DIV
3.2 Vp-p
0.9 Vp-p
1 Vp-p
ed
21 µs
1 V/DIV, 100 ns/DIV
ws
IC701 3 (LRCLK)
3.4 Vp-p
3.2 Vp-p
500 mV/DIV, 20 µs/DIV
2 V/DIV, 10 ns/DIV
wj
200 ns
H
IC101 6 (DVDRFIP)
(DVD play mode)
IC501 qd (XOUT)
0.9 Vp-p
4.2 Vp-p
2
wa
– AMP Board –
1 V/DIV, 20 µs/DIV
500 mV/DIV, 10 ns/DIV
HCD-X1V
– DISPLAY Board –
ta
IC803 tl (OSC1)
3.2 Vp-p
636 ns
1 V/DIV, 200 ns/DIV
ts
Q801 (Base)
15.2 Vp-p
6.8 µs
5 V/DIV, 2 µs/DIV
73
HCD-X1V
• IC Block Diagrams
– DMB12 Board –
– RELAY Board –
IC105, 107, 703 TK11133CSCL-G
IC702 TK11118CSCL-G
IC707 TK11150CSCL-G
VIN
VOUT
IC701, 711, 721
5
4
BA6956AN
TSD
OVER HEAT &
OVER CURRENT
PROTECTION
OUT1
6
7
8
9
RIN
RNF
5
GND
4
FIN
3
VCC
2
VM
1
OUT2
CONTROL
CIRCUIT
VREF
CONTROL LOGIC
1
2
3
VCONT
GND
NP
BANDGAP
REFERENCE
– D-IO Board –
– MAIN Board –
IC1004 TC74HC151AF (EL)
IC1, 505, 506, 507, 703 SI-3010KM-TL
D3 1
16 VCC
D2 2
D2 D3 D4
15 D4
D1 3
D1
D5
14 D5
D0 4
D0
D6
13 D6
Y 5
Y
D7
12 D7
XY 6
W
A
11 A
VC 1
VIN 2
OE 7
GND 8
S
C
B
GND 3
TSD
–
+
10 B
9 C
REF
VOUT 4
ADJ 5
74
HCD-X1V
IC200, 201, 202
IC203 BH7868FS-E2
NJM2235V (TE2)
8 GND
VIN 1 1
BUFFER
7 V OUT
SW 1 2
6MHz
LPF
VCC1 1
S-DC OUT
S1/S2
S2 3
VIN 2 3
C IN 4
BIAS
SW 2 4
75Ω
BIAS
MUTE1 5
MUTE1
CV IN 6
CLAMP
6dB
+
31 S-DC OUT
L
6MHz
LPF
6dB
75Ω
H
6 V+
5 VIN 3
32 C OUT
S1 2
30 CV OUT
29 CV OUT SAG
SEL (CV/MIX) 7
28 GND
IC350, 351 MC14052 BDR2
Y IN 8
CLAMP
BIAS 9
BIAS
6MHz
LPF
6dB
75Ω
26 Y OUT SAG
SEL (BIAS/CLAMP) 10
2X0
25 GND
H
BIAS
16 VDD
1
PY/G IN 11
15 X2
2X2
2
2XCOM
3
14 X1
2X3
4
13 XCOM
27 Y OUT
6dB
CLAMP
12MHz
LPF
75Ω
L
24 PY/G OUT
23 PY/G OUT SAG
GND 12
22 GND
PB/B IN 13
BIAS
MUTE2 14
MUTE2
12MHz
LPF
6dB
12 X0
2X1 5
75Ω
21 PB/B OUT
20 PB/B OUT SAG
INH
6
11 X3
VEE
7
10 A
VSS
8
9
19 GND
PR/R IN 15
BIAS
12MHz
LPF
6dB
75Ω
18 PR/R OUT
B
17 PR/R OUT SAG
VCC2 16
IC503 PST3635NR
VIN
VOUT
IC502 TK11133CSCL-G
5
4
OUT 1
5 CD
VDD 2
OVER HEAT &
OVER CURRENT
PROTECTION
–
+
CONTROL
CIRCUIT
VREF
BANDGAP
REFERENCE
4 NC
1
2
3
VCONT
GND
NP
GND 3
75
HCD-X1V
IC504 NJM2887DL3 (TE2)
IC701 WM8782SEDS/R
20 M/S
MCLK 1
DOUT 2
LRCLK 3
THERMAL
PROTECTION
BANDGAP
REFERENCE
AUDIO
INTERFACE
DGND 4
DVDD 5
+
–
DIGITAL
FILTERS
–
+
A/D
CONVERTER
19 AINL
18 AINOPL
17 COM
1
2
3
4
5
CONTROL
VIN
GND
VOUT
VADJ
BCLK 6
DIGITAL
FILTERS
IWL 7
FSAMPEN 8
FORMAT 9
–
+
A/D
CONVERTER
CONTROL
INTERFACE
16 AINR
15 AINOPR
14 AGND
VMID 10
13 AVDD
+
–
12 VREFP
11 VREFGND
23 EMPHA
AMP
22 XIN
XSEL 39
21 XOUT
20 XMCK
MODE0 40
DATA SELECTOR
19 DVDD
MODE1 41
18 DGND
DATA SELECTOR
DGND 42
17 XSTATE
16 DATAO
DVDD 43
BUFFER RAM
DOSEL1 45
DEMODULATION
&
LOCK DETECT
CKSEL0 46
CKSEL1 47
CLOCK
SELECTOR
DOSEL0 44
PLL
INPUT SELECTOR
76
8
9 10
11
12
AVDD
AGND
DIN1
7
LPF
DIN0
6
AGND
DOUT
5
SDIN
4
DVDD
3
DIN2
2
DGND
1
DISEL
XMODE 48
15 LRCK
14 BCK
13 CKOUT
1
3B
3Y OUTPUT
3A
4B
1A 1B 1Y 2A 2B 2Y
2
3
4
INPUTS
5
6
INPUTS
7 8
GND
C-BIT DETECT
CLK 38
4A 4B 4Y 3A 3B 3Y
2Y OUTPUT
S
24 AUDIO
9
2B
G
PA,PB DETECT
14 13 12 11 10
INPUTS
2A
FS CALCULATION
SELECT
CE 37
MICRO
CONTROLLER
REGULATOR
16 15
4Y OUTPUT
25
1Y OUTPUT
CSFLAG
26
4A
F0/FSB0
27
1B
F1/FSB1
28
INPUTS
1A
F2/DLMP
32 31 30 29
VCC
OUTPUT CTL
VF/DATAO2
33
DVDD
VREF
34
DGND
BPSYNC
36 35
DI
ERROR
IC704 SN74LVC257APWR
DO
IC702 LC890561W
HCD-X1V
IC706 SN74LVC1G79DCKR
D
1
CLK 2
C
5 VCC
C
C
TG
TG
TG
_
C
_
C
_
C
C
TG
_
C
C
_
C
GND 3
4
Q
– AMP Board –
XVDD
HPVDDL
HPOUTL1
HPVSSL
HPOUTL2
HPVDDR
HPOUTR1
HPVSSR
HPOUTR2
FSOI
FSOCKO
CXD9876R
XFSOIN
IC3010, 3020, 3030
48
47
46
45
44
43
42
41
40
39
38 37
CLOCK
GENERATOR
(SECONDARY)
CLOCK
GENERATOR
(PRIMARY)
XVSS 1
36 XFSIIN
35 DVDD
VSUBC 2
34 TEST
VSSR 3
33 BFVSS
OUTR2 4
32 BFVDD
VDDR 5
OUTR1 6
VSSR 7
PWM
LINER
INTERPOLATOR
∆Σ
FILTER &
LOW CUT
FILTER
GAIN
CONTROL
SAMPLING
RATE
CONVERTER
VSSL 8
SgP
31 DATA
30 BCK
29 LRCK
28 MCKSEL
OUTL2 9
27 INIT
VDDL 10
INIT/
MUTE
OUTL1 11
26 SFLAG
SERIAL
CONTROLLER
25 OVFFLAGL
13
14
15
16
17
18
19
20
21
22
23
24
XOVSS
XFSOOUT
XOVDD
DVDD
DVSS
NSPMUTE
SOFTMUTE
PGMUTE
SCDT
SCSHIFT
SCLATCH
OVFFLAGR
VSSL 12
77
HCD-X1V
VIN
VOUT
IC3050 TK11118CSCL-G
5
4
OVER HEAT &
OVER CURRENT
PROTECTION
CONTROL
CIRCUIT
2
3
NP
VCONT
1
GND
BANDGAP
REFERENCE
IC3100, 3150, 3200, 3250, 3300, 3350 CXD9883M
BST_A
1
GVDD_A
2
/OTW
3
Over
Current
Fault
VREG
/SD
4
/RESET
5
PWM_A
6
OC_ADJ
7
GND
8
AGND
9
Stuck
Detect
VREG 10
M3 11
M2 12
OLP
OTP
CB3C
M1 13
/PCR Power-Up
Reset
/UVP
31 PGND
Over
Current
Fault
Under
Voltage
Protection
15
GND
16
GVDD_B
17
BST_B 18
78
28 OUT_A
27 OUT_B
26 OUT_B
25 OUT_B
Gate
Drive
24 PGND
/HIZ_HS_B
/HIZ_LS_B
Timing
Control
REG
Over
Current
Fault
VREG
GVDD_A
GVDD_B
23 PGND
Protection
Logic
VREG
VDD
29 OUT_A
/UVP
/UVP_VREG
PWM_B 14
30 OUT_A
Gate
Drive
/RESET_A
Temperature
waming/error
/HIZ_HS_X
/HIZ_LS_X
/OCH_X
/OCL_X
/RESET_X
32 PGND
Protection
Logic
/OCH_A
/OCL_A
Programmable
Current sense
Protection
and
Reset
Logic
33 PGND
/HIZ_LS_A
Timing
Control
35 PVDD_A
34 PVDD_A
Gate
Drive
/HIZ_HS_A
36 PVDD_A
22 PGND
Stuck
Detect
/OCH_B
/OCL_B
21 PVDD_B
Gate
Drive
20 PVDD_B
/RESET_B
Over
Current
Fault
19 PVDD_B
HCD-X1V
– DISPLAY Board –
IC803 ML9208-03MBZ03B
64 VDD
8 BIT SHIFT
REGISTER
63 DA
62 CP
61 CS
60 RESET
P1 1
P2 2
PORT
DRIVER
AD2 3
AD
DRIVER
AD1 4
COMMAND
DECODER
CONTROL
CIRCUIT
ADRAM
16W × 2B
TIMING
GENERATOR2
CGRAM
248W × 35B
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
DCRAM
16W × 8B
TIMING
GENERATOR1
OSCILLATOR
57 GND
56 VFL
CGRAM
8W × 35B
ADDRESS
SELECTOR
READ
ADDRESS
COUNTER
WRITE
ADDRESS
COUNTER
DIGIT
CONTROL
GRID
DRIVER
SEGMENT
DRIVER
59 OSC1
58 OSC0
DUTY
CONTROL
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
COM16
COM15
COM14
COM13
COM12
COM11
COM10
COM9
COM8
COM7
COM6
COM5
COM4
COM3
COM2
COM1
39
38
37
36
35
34
33
SEG35
SEG34
SEG33
SEG32
SEG31
SEG30
SEG29
– POWER Board –
IC507 SI-3010KM-TL
VC 1
VIN 2
GND 3
TSD
–
+
REF
VOUT 4
ADJ 5
79
HCD-X1V
IC901 STR-F6138-LF1352 (US, Canadian models)
IC901 STR-F6168-LF1352 (AEP, UK models)
CURRENT
MIRROR
OSC
LATCH
DELAY
DELAY
OVER
CURRENT
PROTECT
2
LOGIC
OVER
CURRENT
PROTECT
2
FEED
BACK
BOTTOM
SKIP
LOGIC
INH
2
OVER
CURRENT
PROTECT
1
INH
1
OVER VOLTAGE
PROTECT
THERMAL
SHUT DOWN
OVER LOAD
PROTECT
INTERNAL BIAS
UNDER VOLTAGE
LOCK OUT
5
FB/OCP
4
VCC
3
DRAIN
1
OCP/INH
2
S/GND
SWITCHING
REGULATOR
BLOCK
IC921 STR-V153
+
−
OVP
UVLO
DELAY
LATCH
INTERNAL
BIAS
+
−
TSD
OFF TIMER
DRIVE
POWER
MOS FET
PRC LATCH
Q S
BLANKING
OLP
+
−
R
+
−
BURST
+
−
DISCHARGE
OCP
+
−
–
+
FB
80
1 2 3
4
5
6 7
8
D
N.C.
SOURCE/OCP
VCC
GND
FB/OLP
N.C.
STARTUP
BUFFER
HCD-X1V
• IC Pin Function Description
DMB12 BOARD IC101 CXD9804R (RF AMP, SERVO DSP, MPEG DECODER)
Pin No.
Pin Name
I/O
1
AGND
-
2
DVDA
I
AC coupled input path A
3
DVDB
I
AC coupled input path B
4
DVDC
I
AC coupled input path C
5
Description
Ground terminal
DVDD
I
AC coupled input path D
6
DVDRFIP
I
AC coupled DVD RF signal input from the optical pick-up block
7
DVDRFIN
I
AC coupled DVD RF signal input terminal Not used
8
MA
I
DC coupled main-beam RF signal input A
9
MB
I
DC coupled main-beam RF signal input B
10
MC
I
DC coupled main-beam RF signal input C
11
MD
I
DC coupled main-beam RF signal input D
12
SA
I
DC coupled sub-beam RF signal input A Not used
13
SB
I
DC coupled sub-beam RF signal input B Not used
14
SC
I
DC coupled sub-beam RF signal input C Not used
15
SD
I
DC coupled sub-beam RF signal input D Not used
16
CDFON
I
CD focusing error negative input terminal Not used
17
CDFOP
I
CD focusing error positive input terminal Not used
18
TNI
I
3 beam satellite PD signal negative input from the optical pick-up block
19
TPI
I
3 beam satellite PD signal positive input from the optical pick-up block
20, 21
MDI1, MDI2
I
Laser power monitor input from the optical pick-up block
22
LDO2
O
Laser diode drive signal output to the optical pick-up block (for DVD)
23
LDO1
O
Laser diode drive signal output to the optical pick-up block (for CD)
24
SVDD3
-
Power supply terminal (+3.3V)
25
CSO
O
Central servo signal output terminal Not used
26
RFLVL
O
RFRP low pass output terminal Not used
27
SGND
-
Ground terminal
28
V2REFO
O
Reference voltage (+2.8V) output terminal Not used
29
V2O
O
Reference voltage (+2V) output to the optical pick-up block
30
VREFO
O
Reference voltage (+1.4V) output terminal
31
FEO
O
Focus error monitor output terminal Not used
32
TEO
O
Tracking error monitor output terminal Not used
33
TEZISLV
O
Slice level of tracking error signal output terminal Not used
34
OPOUT
O
Output from the internal operational amplifier Not used
35
OP_INN
I
Negative input to the internal operational amplifier Not used
36
OP_INP
I
Positive input to the internal operational amplifier Not used
37
DMO
O
Spindle motor control signal output to the motor driver
38
FMO
O
Sled motor control signal output to the motor driver
39
TROPENPWM
O
Loading motor control signal output terminal Not used
40
IOPMON
I
Power monitor terminal
41
TRO
O
Tracking coil control signal output to the coil driver
42
FOO
O
Focus coil control signal output to the coil driver
43
USB_VSS
-
Ground terminal
44
USBP
I/O
USB communication data input/output terminal Not used
45
USBN
I/O
USB communication data input/output terminal Not used
46
USB_VDD3
-
Power supply terminal (+3.3V)
47
SPFG
I
Spindle motor hall sensor input from the motor driver
81
HCD-X1V
Pin No.
Pin Name
I/O
48
MSW
O
CD/DVD selection signal output terminal "L": CD, "H": DVD
49
CKSW
I
Chucking detection switch input terminal Not used
50
OCSW
I
Disc table open/close detection switch input terminal Not used
51
EEWP
O
Write protect signal output to the EEPROM
52
DVDD18
-
Power supply terminal (+1.8V)
53 to 61
HA2 to HA8,
HA18, HA19
O
Address signal output to the flash ROM
Description
62
DVSS
-
Ground terminal
63
APLLCAP
-
Connection terminal for an external capacitor
64
APLLVSS
-
Ground terminal
65
APLLVDD3
-
Power supply terminal (+3.3V)
66
XWR
O
Write enable signal output to the flash ROM
67 to 72
HA16 to HA11
O
Address signal output to the flash ROM
73
DVDD3
-
Power supply terminal (+3.3V)
74 to 76
HA10, HA9,
HA20
O
Address signal output to the flash ROM
77
XROMCS
O
Chip select signal output to the flash ROM
78
HA1
O
Address signal output to the flash ROM
79
XRD
O
Read enable signal output to the flash ROM
80
DVDD3
-
81 to 84
HD0 to HD3
I/O
85
DVSS
-
86 to 88
HD4 to HD6
I/O
Two-way data bus terminal with the flash ROM
89
HA21
O
Address signal output to the flash ROM
90
ALE
O
Address latch enable signal output terminal Not used
91
HD7
I/O
Two-way data bus terminal with the flash ROM
92, 93
HA17, HA0
O
Address signal output to the flash ROM
94
DVSS
-
Ground terminal
95
UWR
O
Write enable signal output terminal Not used
96
URD
O
Read enable signal output terminal Not used
97
DVDD18
-
Power supply terminal (+1.8V)
98
IFSDO
O
Serial data output to the system controller
99
IFCK
O
Serial data transfer clock signal output to the system controller
100
XIFCS
O
Chip select signal output to the system controller
101
IFSOI
I
Serial data input from the system controller
102
SCL
O
Serial data transfer clock signal output to the EEPROM
103
SDA
I/O
Two-way data bus with the EEPROM
104
TRG-SW
I
Trigger detection switch input terminal Not used
105
XRST
O
Reset signal output to the HDMI controller "L": reset
106
RXD
I
Receive data input terminal for UART communication when data writing to flash memory
107
TXD
O
Transmit data output terminal for UART communication when data writing to flash memory
108
DVDD3
-
Power supply terminal (+3.3V)
109
ICE
I
ICE mode enable signal input terminal Not used
110
XSYSRST
I
Reset signal input from the system controller "L": reset
82
Power supply terminal (+3.3V)
Two-way data bus terminal with the flash ROM
Ground terminal
111
IR
I
IR control signal input terminal Not used
112
XTXINT
O
Interrupt request signal output terminal Not used
113
DQM0
O
Data mask signal output to the SD-RAM
114
XIF5SY
I
Busy signal input from the system controller
HCD-X1V
Pin No.
Pin Name
I/O
115
RD7
I/O
116
DVSS
-
117, 118
RD6, RD5
I/O
119
DVSS
-
120, 121
RD4, RD3
I/O
122
DVDD18
123 to 126 RD2 to RD0, RD15
I/O
Description
Two-way data bus with the SD-RAM
Ground terminal
Two-way data bus with the SD-RAM
Ground terminal
Two-way data bus with the SD-RAM
Power supply terminal (+1.8V)
Two-way data bus with the SD-RAM
127
DVDD3
-
128 to 133
RD14 to RD9
I/O
134
DVSS
-
135
RD8
I/O
Two-way data bus with the SD-RAM
136
LINYSW
I
Limit detection switch input terminal
137
DQM1
O
Data mask signal output to the SD-RAM
138
RWE
O
Write enable signal output to the SD-RAM
139
CAS
O
Column address strobe signal output to the SD-RAM
140
RAS
O
Row address strobe signal output to the SD-RAM
141
DVDD3
-
Power supply terminal (+3.3V)
142
RCS
O
Chip select signal output to the SD-RAM
143
BA0
O
Bank address signal output to the SD-RAM
144
DVSS
-
Ground terminal
Power supply terminal (+3.3V)
Two-way data bus with the SD-RAM
Ground terminal
145
BA1
O
Bank address signal output to the SD-RAM
146, 147
RA10, RA0
O
Address signal output to the SD-RAM
148
DVSS
-
Ground terminal
149 to 151
RA1 to RA3
O
Address signal output to the SD-RAM
152
DVDD18
-
Power supply terminal (+1.8V)
153
RVREF
-
Not used
154
RCLKB
-
Not used
155
DVDD3
-
Power supply terminal (+3.3V)
156
DRCLK
O
Serial data transfer clock signal output to the SD-RAM
157
CKE
O
Clock enable signal output to the SD-RAM
158 to 160 RA11, RA9, RA8
O
Address signal output to the SD-RAM
161
DVSS
-
Ground terminal
162
RA7
O
Address signal output to the SD-RAM
163
DVSS
-
Ground terminal
164 to 166
RA6 to RA4
O
Address signal output to the SD-RAM
168
DVDD3
-
Power supply terminal (+3.3V)
168 to 172
SMPTE_Y (7) to
SMPTE_Y (3)
O
Video signal output to the HDMI transmitter
173
DVDD18
-
Power supply terminal (+1.8V)
174
SMPTE_Y (2)
O
Video signal output to the HDMI transmitter
175
DVSS
-
Ground terminal
176, 177
SMPTE_Y (1),
SMPTE_Y (0)
O
Video signal output to the HDMI transmitter
178
VCLK
O
System clock (27 MHz) signal output to the HDMI transmitter
179
WIDE
O
Normal/squeeze selection signal output to the video amplifier
"L": normal, "H": squeeze
180
ADSCK
-
Not used
181
TSD_M
O
Thermal shut down signal output to the motor/coil driver
83
HCD-X1V
Pin No.
Pin Name
I/O
182
DVDD3
-
Power supply terminal (+3.3V)
183
MUTE
O
Muting signal output to the motor/coil driver
184
MUTE123
O
Muting signal output to the motor/coil driver
185
FWD
O
Loading motor drive signal output terminal (forward direction) Not used
186
REV
O
Loading motor drive signal output terminal (reverse direction) Not used
187
ADSDO
-
Not used
188
XDACS
-
Not used
189
DAVCC
-
Power supply terminal (+3.3V)
190
Description
DACVDDC
-
For bandgap reference voltage terminal
191
FS
-
Full scale adjustment terminal
192
CIN
-
Not used
193
DAVSS
-
Ground terminal
194
YUV1
O
Y signal output to the video amplifier
195
DAVDD
-
Power supply terminal (+3.3V)
196
YUV2
O
Chroma signal output to the video amplifier
197
DAVSS
-
Ground terminal
198
YUV3
O
Video signal output to the video amplifier
199
DAVDD
-
Power supply terminal (+3.3V)
200
YUV4
O
Chroma signal output to the video amplifier
201
DAVSS
-
Ground terminal
202, 203
YUV5, YUV6
O
Component video signal output to the video amplifier
204
DVDD3
-
Power supply terminal (+3.3V)
205
VSYN
O
Vertical sync signal output to the HDMI transmitter and HDMI controller
206
YUV7
O
Muting control signal output terminal Not used
207
SMBSY
O
Horizontal sync signal output to the HDMI transmitter
208
SMSCK
O
Serial data transfer clock signal output to the HDMI controller
209
SMSDI
I
Serial data input from the HDMI controller
210
SMSDO
O
Serial data output to the HDMI controller
211
XSMCS
O
Chip select signal output to the HDMI controller
212
DVDD3
-
Power supply terminal (+3.3V)
213
ALRCK
O
L/R sampling clock signal output to the DSP and HDMI transmitter
214
ABCK
O
Bit clock signal output to the DSP and HDMI transmitter
215
ACLK
O
Master clock signal output to the DSP and HDMI transmitter
216
DVSS
-
Ground terminal
217 to 219
ASDATA0 to
ASDATA2
O
Audio serial data output to the DSP and HDMI transmitter
220
SPDATA
I
Analog audio data input terminal Not used
221
DVDD18
-
Power supply terminal (+1.8V)
222
ASDATA4
O
Audio serial data output to the HDMI transmitter
223
DVSS
-
Ground terminal
224
GPIO
-
Not used
225
SPDIF
O
SPDIF digital audio signal output to the HDMI transmitter and digital audio interface receiver
226
RFGND18
-
Ground terminal
227
RFVDD18
-
Power supply terminal (+1.8V)
228
XTALO
O
System clock output terminal Not used
229
XTALI
I
System clock (27 MHz) signal input terminal
230
JITFO
O
Output terminal of the RF jitter meter
231
JITFN
I
Input terminal of the RF jitter meter
84
HCD-X1V
Pin No.
Pin Name
I/O
232
PLLVSS
-
Ground terminal
233
IDAC
-
Not used
234
PLLVDD3
-
Power supply terminal (+3.3V)
235
LPFON
O
Data PLL loop filter output terminal
236
LPFIP
I
Data PLL loop filter input terminal
Description
237
LPFIN
I
Data PLL loop filter input terminal
238
LPFOP
O
Data PLL loop filter output terminal
239
VDD3
-
Power supply terminal (+3.3V)
240
VCM
-
Not used
241
VSS
-
Ground terminal
242, 243
VREFP, VREFN
-
For reference voltage terminal
244
RFVDD3
-
Power supply terminal (+3.3V)
245
RFRPDC
O
RF ripple detect output terminal
246
RFRPAC
I
RF ripple detect input terminal
247
HRFZC
I
High frequency RF ripple zero crossing terminal
248
CRTPLP
O
Defect level filter capacitor connecting terminal
249
RFGND
-
Ground terminal
250, 251
CEQP, CEQN
-
Not used
252
OSP
O
RF offset cancellation capacitor connecting terminal
253
OSN
O
RF offset cancellation capacitor connecting terminal
254
RFGC
O
RF AGC loop capacitor connecting for DVD-ROM
255
IREF
I
Reference current input terminal
256
AVDD3
-
Power supply terminal (+3.3V)
85
HCD-X1V
DMB12 BOARD IC701 CXD9873Q (HDMI TRANSMITTER)
Pin No.
Pin Name
I/O
1
Description
DVSS
-
Ground terminal (digital system)
2 to 9
C0 to C7
I
Digital chroma signal input terminal Not used
10
DVDD33
-
Power supply terminal (+3.3V) (digital system)
11
VCK
I
System clock (27 MHz) signal input from the servo DSP
12
DVSS
-
Ground terminal (digital system)
13 to 20
Y0 to Y7
I
Video signal input from the servo DSP
21
SSCK
I
Serial data transfer clock signal input from the HDMI controller
22
SSO
I/O
23
DVDD18
-
Power supply terminal (+1.8V) (for digital core)
24
PWDN
I
Power down signal input terminal "L": power down Not used
25
RST
I
Reset signal input from the HDMI controller "L": reset
26
Two-way data bus with the HDMI controller
CLK
I
System clock (27 MHz) signal input terminal
27
INT
O
Interrupt signal output to the HDMI controller
28
DVSS
-
Ground terminal (digital system)
29, 30
A7, A6
-
Not used
31
TRAP2
I
NTSC/PAL selection signal input from the HDMI controller
32, 33
TRAP1, TRAP0
-
Not used
34
MSCK
I
Serial data transfer clock signal input from the HDMI controller
35
MSD
I/O
Two-way data bus with EEPROM and HDMI controller
36
TYPE
-
Not used
37
ASDATA4
-
Not used
38
VSYNC
I
Vertical sync signal input from servo DSP
39
HSYNC
I
Horizontal sync signal input from servo DSP
40
HTPLG
I
HDMI hot-plug detection signal input terminal
41
AVSS
-
Ground terminal (analog system)
42
PLLC0
-
External capacitor ground terminal (for PLL)
43
PLLC1
-
External capacitor connection terminal (for PLL)
44, 45
PLL_AVDD3
-
Power supply terminal (+3.3V) (analog system) (for PLL)
46, 47
AVSS
-
Ground terminal (analog system)
86
48
TCKN
O
TMDS clock signal (negative) output to the HDMI OUT connector
49
TCKP
O
TMDS clock signal (positive) output to the HDMI OUT connector
50
AVDD3
-
Power supply terminal (+3.3V) (analog system)
51
TX0N
O
TMDS data (negative) output to the HDMI OUT connector
52
TX0P
O
TMDS data (positive) output to the HDMI OUT connector
53
AVDD
-
Power supply terminal (+3.3V) (analog system)
54
TX1N
O
TMDS data (negative) output to the HDMI OUT connector
55
TX1P
O
TMDS data (positive) output to the HDMI OUT connector
56
AVDD3
-
Power supply terminal (+3.3V) (analog system)
57
TX2N
O
TMDS data (negative) output to the HDMI OUT connector
58
TX2P
O
TMDS data (positive) output to the HDMI OUT connector
59
AVSS
-
Ground terminal (analog system)
60
SWING
I
HDMI output swing adjustment signal input terminal Not used
61
DAC_AVDD3
-
Power supply terminal (+3.3V) (analog system) (for D/A converter)
62
VREF
-
Reference voltage terminal (for D/A converter)
63
FS
-
Full scale adjustment terminal (for D/A converter)
64
AVSS
-
Ground terminal (analog system) (for D/A converter)
HCD-X1V
Pin No.
Pin Name
I/O
65
DAC_AVDD3
-
Power supply terminal (+3.3V) (analog system) (for D/A converter)
66
AVSS
-
Ground terminal (analog system) (for D/A converter)
67
Power supply terminal (+3.3V) (analog system) (for D/A converter)
Description
DAC_AVDD3
-
68
G
O
Component analog video signal (Y or green) output terminal Not used
69
AVSS
-
Ground terminal (analog system) (for D/A converter)
70
B
O
Component analog video signal (Cb or blue) output terminal Not used
71
R
O
Component analog video signal (Cr or red) output terminal Not used
72
SPDIF
I
SPDIF digital audio signal input from the servo DSP
73 to 76
AD3 to AD0
I
Audio serial data input from the servo DSP
77
ACL
I
Master clock signal input from the servo DSP
78
ABCK
I
Bit clock signal input from the servo DSP
79
ALRCK
I
L/R sampling clock signal input from the servo DSP
80
DVDD18
-
Power supply terminal (+1.8V) (for digital core)
87
HCD-X1V
DMB12 BOARD IC708 MB95F108ASPFV-GE1-H0601 (HDMI CONTROLLER)
Pin No.
Pin Name
I/O
1
AVCC
-
Power supply terminal (+3.3V)
2
AVR
I
Reference voltage (+3.3V) input terminal
3 to 6
PE3/INT13 to
PE0/INT10
-
Not used
7 to 10
P83 to P80
-
Not used
11, 12
P71/TI0,
P70/TO0
-
Not used
13
MOD
-
Not used
14
X0
I
System clock input terminal (10 MHz)
15
X1
O
System clock output terminal (10 MHz)
16
VSS
-
Ground terminal
17
VDD
-
Power supply terminal (+3.3V)
18
PG0/(CIN)
-
Not used
19, 20
PG2/X1A,
PG2/X0A
-
Not used
21
XRST
I
Reset signal input from the servo DSP and system controller "L": reset
22
VSYNC
I
Vertical sync signal input from the servo DSP
23
Description
XSMCS
I
Chip select signal input from the servo DSP
24
XTXINT
I
Interrupt signal input from the HDMI transmitter
25 to 29
P03/INT03 to
P07/INT07
-
Not used
30
SDI
I
Serial data input from the servo DSP
31
SDO
O
Serial data output to the servo DSP
32
SCK
I
Serial data transfer clock signal input from the servo DSP
33
ADTG/TRG0/P13
-
Not used
34
PPG0/P14
-
Not used
35, 36
PPG00/P20,
PPG01/P21
-
Not used
37, 38
TO00/P22,
TO01/P23
-
Not used
39
EC0/P24
-
Not used
40
SCL0
O
Serial data transfer clock signal output to the HDMI OUT connector
41
SDA0
I/O
Two-way data bus with the HDMI OUT connector
42
PPG1/P52
-
Not used
43
TRG1/P53
-
Not used
44, 45
PPG10/P60 to
PPG11/P61
-
Not used
46, 47
T010/P62 to
T011/P63
-
Not used
48
EC1/P64
-
Not used
49
HDCP-SCL
O
Serial data transfer clock signal output to the HDMI transmitter and EEPROM
50
HDCP-SDA
I/O
Two-way data bus with the HDMI transmitter and EEPROM
51
HDCP-WP
O
Write protect signal output to the EEPROM
52 to 57
P43/AN11 to
P36/AN05
-
Not used
58
P35/AN05
O
Power on/off control signal output terminal for HDMI OUT connector "H": power on
59
XTXRST
O
Reset signal output to the HDMI transmitter "L": reset
60
XPDWN
-
Not used
88
HCD-X1V
Pin No.
Pin Name
I/O
61
TRAP2
O
NTSC/PAL selection signal output to the HDMI transmitter
62
SDA
I/O
Two-way data bus with the HDMI transmitter
63
SCK
O
Serial data transfer clock signal output to the HDMI transmitter
64
AVSS
-
Ground terminal
Description
89
HCD-X1V
MAIN BOARD IC2 ADSST-AVR-1115 (DSP)
Pin No.
Pin Name
I/O
Description
1
VDDINT
-
Power supply terminal (+1.2V) (for core)
2
CLKCFG0
I
Core instruction rate to CLKIN (pin 142) ratio selection signal input terminal
Fixed at "L" in this set
3
CLKCFG1
I
Core instruction rate to CLKIN (pin 142) ratio selection signal input terminal
Fixed at "H" in this set
4, 5
BOOTCFG0,
BOOTCFG1
I
Boot mode selection signal input terminal Fixed at "H" in this set
6
GND
-
Ground terminal
7
VDDEXT
-
Power supply terminal (+3.3V) (for I/0)
8
GND
-
Ground terminal
9
VDDINT
-
Power supply terminal (+1.2V) (for core)
10
GND
-
Ground terminal
11
VDDINT
-
Power supply terminal (+1.2V) (for core)
12
GND
-
Ground terminal
13
VDDINT
-
Power supply terminal (+1.2V) (for core)
14
GND
-
Ground terminal
15
INT_REQ
O
Interrupt signal output to the system controller
16
DIR_ERR
I
PLL lock error signal and data error flag input from the digital audio interface receiver
17
AD7
I/O
18
GND
-
Ground terminal
19
VDDINT
-
Power supply terminal (+1.2V) (for core)
20
GND
-
Ground terminal
21
VDDEXT
-
Power supply terminal (+3.3V) (for I/0)
22
Two-way address and data bus terminal Not used
GND
-
Ground terminal
23
VDDINT
-
Power supply terminal (+1.2V) (for core)
24 to 26
AD6 to AD4
I/O
27
VDDINT
-
Power supply terminal (+1.2V) (for core)
Ground terminal
Two-way address and data bus terminal Not used
28
GND
-
29, 30
AD3, AD2
I/O
31
VDDEXT
-
Power supply terminal (+3.3V) (for I/0)
32
Ground terminal
Two-way address and data bus terminal Not used
GND
-
33, 34
AD1, AD0
I/O
Two-way address and data bus terminal Not used
35
WR*
O
Write enable signal output terminal Not used
36, 37
VDDINT
-
Power supply terminal (+1.2V) (for core)
38
GND
-
Ground terminal
39
RD*
O
Read enable signal output terminal Not used
40
ALE
O
Address latch enable signal output terminal Not used
41 to 43
Two-way address and data bus terminal Not used
AD15 to AD13
I/O
44
GND
-
Ground terminal
45
VDDEXT
-
Power supply terminal (+3.3V) (for I/0)
46
AD12
I/O
47
VDDINT
-
Power supply terminal (+1.2V) (for core)
48
GND
-
Ground terminal
49 to 52
AD11 to AD8
I/O
53
A16
-
Not used
54
VDDINT
-
Power supply terminal (+1.2V) (for core)
55
GND
-
Ground terminal
90
Two-way address and data bus terminal Not used
Two-way address and data bus terminal Not used
HCD-X1V
Pin No.
Pin Name
I/O
56, 57
A17, A18
-
Not used
Description
58
GND
-
Ground terminal
59
VDDEXT
-
Power supply terminal (+3.3V) (for I/0)
60
VDDINT
-
Power supply terminal (+1.2V) (for core)
61
GND
-
Ground terminal
62
PF_CE
-
Not used
63
SPI_MAS
-
Not used
64, 65
DPSOA, DPSOB
O
Audio serial data output to the stream processor
66
VDDINT
-
Power supply terminal (+1.2V) (for core)
67
GND
-
Ground terminal
68
VDDINT
-
Power supply terminal (+1.2V) (for core)
69
GND
-
Ground terminal
70
DPSOC
O
Audio serial data output to the stream processor
71
DPSOD
O
Audio serial data output terminal Not used
72
VDDINT
-
Power supply terminal (+1.2V) (for core)
73
VDDEXT
-
Power supply terminal (+3.3V) (for I/0)
74
GND
-
Ground terminal
75
VDDINT
-
Power supply terminal (+1.2V) (for core)
76
GND
-
Ground terminal
77
DPSOE
O
Audio serial data output terminal Not used
78
DPSIA
I
Audio serial data input from the digital audio interface receiver
79
DPSIB
I
Audio serial data input from the servo DSP or A/D converter
80, 81
DPSIC, DPSID
I
Audio serial data input from the servo DSP
82
DPSIE
I
Audio serial data input from the A/D converter
83
VDDINT
-
Power supply terminal (+1.2V) (for core)
84, 85
GND
-
Ground terminal
86
DPDVLRCK
O
L/R sampling clock signal output to the stream processor
87
DPDVBCK
O
Bit clock signal output to the stream processor
88
DPLRCK
I
L/R sampling clock signal input from the servo DSP or digital audio interface receiver
89
DPBCK
I
Bit clock signal input from the servo DSP or digital audio interface receiver
90
VDDINT
-
Power supply terminal (+1.2V) (for core)
91, 92
GND
-
Ground terminal
93
VDDEXT
-
Power supply terminal (+3.3V) (for I/0)
94
DPFSCK
I
Audio clock signal input from the servo DSP or digital audio interface receiver
95
GND
-
Ground terminal
96
VDDINT
-
Power supply terminal (+1.2V) (for core)
97
NONAUDIO*
I
PCM audio data input from the digital audio interface receiver
98
SF_CE*
-
Not used
99
VDDINT
-
Power supply terminal (+1.2V) (for core)
100
GND
-
Ground terminal
101
VDDINT
-
Power supply terminal (+1.2V) (for core)
102
Ground terminal
GND
-
103
VDDINT
-
Power supply terminal (+1.2V) (for core)
104
GND
-
Ground terminal
105
VDDINT
-
Power supply terminal (+1.2V) (for core)
106
GND
-
Ground terminal
107, 108
VDDINT
-
Power supply terminal (+1.2V) (for core)
91
HCD-X1V
Pin No.
Pin Name
I/O
109
GND
-
Ground terminal
110
VDDINT
-
Power supply terminal (+1.2V) (for core)
111
Ground terminal
GND
-
112
VDDINT
-
Power supply terminal (+1.2V) (for core)
113
GND
-
Ground terminal
114
VDDINT
-
Power supply terminal (+1.2V) (for core)
115
GND
-
Ground terminal
116
VDDEXT
-
Power supply terminal (+3.3V) (for I/0)
117
GND
-
Ground terminal
118
Power supply terminal (+1.2V) (for core)
VDDINT
-
119
GND
-
Ground terminal
120
VDDINT
-
Power supply terminal (+1.2V) (for core)
121
RESET*
I
Reset signal input from the system controller "L": reset
122
SPIDS*
I
Device selection signal input from the system controller
123
GND
-
Ground terminal
124
VDDINT
-
Power supply terminal (+1.2V) (for core)
125
Serial data transfer clock signal input from the system controller
SPICLK
I
126
MISO
O
Serial data output to the system controller
127
MOSI
I
Serial data input from the system controller
128
GND
-
Ground terminal
129
VDDINT
-
Power supply terminal (+1.2V) (for core)
130
VDDEXT
-
Power supply terminal (+3.3V) (for I/0)
131
AVDD
-
Power supply terminal (+1.2V) (analog system)
132
AVSS
-
Ground terminal (analog system)
133
GND
-
Ground terminal
134
CLKOUT
O
Local clock signal output terminal Not used
135
EMU*
O
Emulation status signal output terminal Not used
136
Test data output terminal (for JTAG) Not used
TDO
O
137
TDI
I
Test data input terminal (for JTAG) Not used
138
TRST*
I
Test reset signal input terminal (for JTAG) Not used
139
TCK
I
Test clock signal input terminal (for JTAG) Not used
140
TMS
I
Test mode select signal input terminal (for JTAG) Not used
141
GND
-
Ground terminal
142
CLKIN
I
System clock input terminal (25 MHz)
143
XTAL
O
System clock output terminal (25 MHz)
VDDEXT
-
Power supply terminal (+3.3V) (for I/0)
144
92
Description
HCD-X1V
MAIN BOARD IC501 M30626MJP-A05FPU0 (SYSTEM CONTROLLER)
Pin No.
Pin Name
1
I/O
Description
DAMP_SCDT
O
2
DAMP_SHIFT
O
Shift clock signal output to the stream processor
3
DSP_INTR
I
Interrupt signal input from the DSP
4
SIRCS_IN
I
SIRCS signal input from the remote control receiver
5
DSP_MOSI
/DIR_DIN
O
Serial data output to the DSP and digital audio interface receiver
6
DSP_MISO
I
Serial data input from the DSP
7
DSP_SPICLK
/DIR_CLK
O
Serial data transfer clock signal output to the DSP and digital audio interface receiver
8
BYTE
I
External data bus width selection signal input terminal
9
CNVSS
I
Processor mode switch input terminal (for test)
10
LED4
O
LED drive signal output terminal
11
FL_RESET
O
Reset signal output to the fluorescent indicator tube driver
12
RESET
I
System reset signal input from the reset signal generator "L": reset
For several hundreds msec. after the power supply rises, "L" is input, then it change to "H"
13
XOUT
O
Main system clock output terminal (5 MHz)
14
VSS
-
Ground terminal
15
XIN
I
Main system clock input terminal (5 MHz)
16
VCC
-
Power supply terminal (+3.3V)
17
NMI
I
Non-maskable interrupt input terminal
Serial data output to the stream processor
Fixed at "L" in this set
Fixed at "L" in this set
Not used
"L": reset
Fixed at "H" in this set
18
DIR_ZERO
I
Audio serial data input from the digital audio interface receiver
19
DIR_CSFLAG
I
CSFLAG data input from the digital audio interface receiver
20
AC_CUT
I
AC cut detection signal input terminal
21
FL_CLK/LED_CLK
O
Serial data transfer clock signal output to the LED driver and fluorescent indicator tube driver
22
LED_LAT
O
Serial data latch pulse signal output to the LED driver
23
LED1
O
LED drive signal output for the FOCUS SUR indicator
24
FL_D_OUT/
LED_DATA
O
Serial data output to the LED driver and fluorescent indicator tube driver
25
FL_CS/STB
O
Chip select signal output to the fluorescent indicator tube driver
26
PWM_OUT
O
Power on/off control signal output terminal for LEDs
27
DIR_ERR
I
PLL lock error signal and data error flag input from the digital audio interface receiver
28
LED2
O
LED drive signal output for the WIDE SUR indicator
29
I2C_CLK
I/O
Two-way I2C clock bus terminal
30
I2C_DATA
I/O
Two-way I2C data bus terminal
31
DVD_SID
O
Serial data output to the servo DSP
32
DVD_SOD
I
Serial data input from the servo DSP
"L": AC cut on
"H": LED on
"H": power on
"H": LED on
Not used
Not used
33
DVD_SCO
I
Serial data transfer clock signal input from the servo DSP
34
DVD_XIFBUSY
O
Busy signal output to the servo DSP
35
CDM_OPEN_SW
I
Disc insert (8/12cm) detect switch input terminal
"L": disc insert
36
LED3
O
LED drive signal output for the 2CH STEREO indicator
37
DVD XIFCS
O
Chip select signal output to the servo DSP
"H": LED on
38
MTK RST
O
Reset signal output to the servo DSP and HDMI controller
39 to 41
P_CONT1 to
P_CONT3
O
Power on/off control signal output terminal
"L": reset
"H": power on
42
RDS_DATA
I
RDS serial data input from the tuner (FM/AM) (AEP and UK models only)
43
TUNED
I
Tuning detection signal input from the tuner (FM/AM)
44
ST_DI
I
Serial data input from the tuner (FM/AM)
"L": tuned
93
HCD-X1V
Pin No.
Pin Name
I/O
Description
45
ST_CLK
O
Serial data transfer clock signal output to the tuner (FM/AM)
46
WRITE CE
I
Chip enable signal input terminal (for flash writing)
47
ST_DO
O
Serial data output to the tuner (FM/AM)
48
ST_CE
O
Serial chip enable signal output to the tuner (FM/AM)
49 to 52 A_SEL3 to A_SEL0
O
Audio signal input selection signal output terminal
53 to 56 V_SEL3 to V_SEL0
O
Video signal input selection signal output terminal
57
N.C.
-
Not used
58
A_SEL4
O
Audio signal input selection signal output terminal
59
MIC_SW2
I
Audio code detection signal input from the AUDIO IN jack "H": audio code in
60, 61
N.C.
-
Not used
62
VCC
-
Power supply terminal (+3.3V)
63
N.C.
-
Not used
64
VSS
-
Ground terminal
65
N.C.
-
Not used
66
DIR_HDOUT
I
Read data input from the digital audio interface receiver
67
DIR_XSTATE
I
Source clock selection monitor input from the digital audio interface receiver
68
DIR_HCE
O
Chip enable signal output to the digital audio interface receiver
69
DIR_RST
O
Reset signal output to the digital audio interface receiver "L": reset
70
SEL_SA-CD
O
Data selection signal output terminal
71
DSP_SPIDS
O
Device selection signal output to the DSP
72
DSP_RESET
O
Reset signal output to the DSP "L": reset
73
N.C.
-
Not used
74
KEY INT
I
Wake up signal input terminal
75
RDS_CLK
I
RDS serial data transfer clock signal input from the tuner (FM/AM)
(AEP and UK models only)
76
DAMP INIT
O
Reset signal output to the stream processor "L": reset
77
DAMP SOFT MUTE
O
Soft muting on/off control signal output to the stream processor "L": muting on
78 to 80
DAMP LATCH1 to
DAMP LATCH3
O
Serial data latch pulse signal output to the stream processor
81
DRIVE_RST (EN)
O
Reset signal output to the digital power amplifier "L": reset
82
DRIVE_OCP (DIAG)
I
Shut down state input from the digital power amplifier "L": shut down
83, 84
OVERFLOW1,
OVERFLOW2
I
Over flow status input from the stream processor
85
IO_CE
O
Serial data latch pulse signal output to the changer controller1
86
IO_RESET
O
Reset signal output to the changer controller1 and changer controller2 "L": reset
87
IO_DI
O
Serial data output to the changer controller1
88
IO_DO
I
Serial data input from the changer controller2
89
IO_CLK
O
Serial data transfer clock signal output to the changer controller1
90
FSDLY
I
Stream processor setting signal input terminal Fixed at "L" in this set
91
OUT2DLY
I
Stream processor setting signal input terminal Fixed at "L" in this set
92
DESTINATION
I
Setting terminal for the destination
93
MODEL
I
Setting terminal for the model
94, 95
KEY2, KEY1
I
Front panel key input terminal (A/D input)
96
VSS
-
Ground terminal
97
KEY0
I
Front panel key input terminal (A/D input)
98
VREF
I
Reference voltage (+3.3V) input terminal
94
99
VCC
-
Power supply terminal (+3.3V)
100
MIC/A.CAL SW
I
Microphone detection signal input from the A.CAL MIC jack "H": microphone in
HCD-X1V
MAIN BOARD IC621 BH2210FV-E2 (CHANGER CONTROLLER1)
Pin No.
Pin Name
I/O
Description
1
CTLIO
I
Input/output selection signal input terminal
2
RESET_B
I
Reset signal input from the system controller
3
CLK
I
Serial data transfer clock signal input from the system controller
4
LATCH
I
Serial data latch pulse signal input from the system controller
5
P15
I
Not used
6
P14
I
Disc insert detection signal input from the disc insert detect sensor
7
P13
I
Disc in (8/12cm) detect switch input terminal
8
P12
I
Disc in (12cm) detect switch input terminal
9
P11
I
Stocker in/out detect switch input terminal
10
P10
I
Disc position detect switch input terminal
"L": disc is play position side in the midst disc is moving between play position and stocker,
"H": disc is stocker side in the midst disc is moving between play position and stocker
11
P9
I
Disc out detect switch input terminal
"L": input, "H": output
Fixed at "L" in this set
"L": reset
"L": play position
"L": play position
"L": the moment disc in/out from stocker
"H": disc out from play position
12
P8
I
Stocking detect switch input terminal
"H": in the midst disc is moving between play position and stocker
13
LATCHO
O
Serial data latch pulse signal output to the changer controller2
14
CLKO
O
Serial data transfer clock signal output to the changer controller2
15
DO1
O
Serial data output to the changer controller2
16
DI2
I
Serial data input terminal
17, 18
P7, P6
O
Not used
19, 20
P5, P4
O
Stocker motor drive signal output terminal
21, 22
P3, P2
O
Mode motor drive control signal output terminal
23, 24
P1, P0
O
Roller motor drive control signal output terminal
25
DO2
O
Serial data output to the changer controller2
26
DI1
I
Serial data input from the system controller
27
VSS
-
Ground terminal
28
VCC
-
Power supply terminal (+3.3V)
Not used
95
HCD-X1V
MAIN BOARD IC622 BH2210FV-E2 (CHANGER CONTROLLER2)
Pin No.
Pin Name
I/O
Description
1
CTLIO
I
Input/output selection signal input terminal "L": input, "H": output Fixed at "L" in this set
2
RESET_B
I
Reset signal input from the system controller
3
CLK
I
Serial data transfer clock signal input from the changer controller1
4
LATCH
I
Serial data latch pulse signal input from the changer controller1
"L": reset
5 to 8
P15 to P12
I
Mode detect rotary encoder input terminal
9 to 12
P11 to P8
I
Stocker position detect rotary encoder input terminal
13
LATCHO
O
Serial data latch pulse signal output terminal Not used
14
CLKO
O
Serial data transfer clock signal output terminal Not used
15
DO1
O
Serial data output terminal Not used
16
DI2
I
Serial data input from the changer controller1
17 to 24
P7 to P0
O
Not used
25
DO2
O
Serial data output to the system controller
26
DI1
I
Serial data input from the changer controller1
27
VSS
-
Ground terminal
28
VCC
-
Power supply terminal (+3.3V)
96
HCD-X1V
LED BOARD IC802 BU2099FV (LED DRIVER)
Pin No.
Pin Name
I/O
Description
1
VSS
-
2
NC
-
Not used
3
DATA
I
Serial data input from the system controller
4
CLK
I
Serial data transfer clock signal input from the system controller
5
LCK
I
Serial data latch pulse signal input from the system controller
6
Q0
O
LED drice signal output of DISC 5 indicator (green) "L": LED on
7
Q1
O
LED drice signal output of DISC 5 indicator (amber) "L": LED on
8
Q2
O
LED drice signal output of DISC 4 indicator (green) "L": LED on
Ground terminal
9
Q3
O
LED drice signal output of DISC 4 indicator (amber) "L": LED on
10
Q4
O
LED drice signal output of DISC 3 indicator (green) "L": LED on
11
Q5
O
LED drice signal output of DISC 3 indicator (amber) "L": LED on
12
Q6
O
LED drice signal output of DISC 2 indicator (green) "L": LED on
13
Q7
O
LED drice signal output of DISC 2 indicator (amber) "L": LED on
14
Q8
O
LED drice signal output of DISC 1 indicator (green) "L": LED on
15
Q9
O
LED drice signal output of DISC 1 indicator (amber) "L": LED on
16, 17
Q10, Q11
-
Not used
18
SO
O
Serial data output terminal Not used
19
OE
I
Output enable signal input terminal Not used
20
VDD
-
Power supply terminal (+3.3V)
97
HCD-X1V
SECTION 8
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
• Abbreviation
CND : Canadian model
8-1.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Accessories are given in the last of the
electrical parts list.
The components identified by mark
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
FRONT/SIDE/TOP PANEL SECTION
15
14
11
10
13
not supplied
(POWER-SW board)
12
10
#3
not supplied
(KEY board)
not supplied
11
10
8
9
(US, CND)
not supplied
not supplied
not
supplied
9
not supplied
not supplied
not supplied
(US, CND)
not supplied
not supplied
7
7
#1
6
not supplied
not supplied
(AUDIO IN
board)
not supplied
4
not supplied
#1
not supplied
5
#1
7
3
not supplied
(LED board)
#1
#3
not supplied
2
MAIN board section
16
#1
1
Ref. No.
Part No.
Description
1
1
2
2
3
X-2109-247-1
X-2149-321-1
A-1179-254-A
A-1179-625-A
1-833-130-11
PANEL ASSY, FRONT (US, CND)
PANEL ASSY, FRONT (AEP, UK)
DISPLAY BOARD, COMPLETE (US, CND)
DISPLAY BOARD, COMPLETE (AEP, UK)
WIRE (FLAT TYPE) (8 CORE)
4
5
6
7
8
1-828-622-11
3-087-053-01
1-500-753-11
3-704-515-22
2-677-331-01
WIRE (FLAT TYPE) (19 CORE)
+BVTP2.6 (3CR)
CLAMP, FERRITE
SCREW (BV/RING)
PANEL (L), SIDE
9
3-077-331-21 +BV3 (3-CR)
98
Remark
Ref. No.
Part No.
Description
10
11
12
13
2-676-410-01
X-2109-248-1
X-2109-249-1
2-677-330-01
CUSHION (BUTTON)
BUTTON (L) ASSY
BUTTON (S) ASSY
ESCUTCHEON (PLAY)
14
15
15
16
#1
2-677-329-01
2-677-508-01
2-677-508-21
2-677-332-01
7-685-871-01
ESCUTCHEON (POWER)
PANEL, TOP (US, CND)
PANEL, TOP (AEP, UK)
PANEL (R), SIDE
SCREW +BVTT 3X6 (S)
#3
7-685-872-09 SCREW +BVTT 3X8 (S)
Remark
HCD-X1V
8-2.
MAIN BOARD SECTION
#1
51
52
not supplied
57
supplied with CN701
53
55
57
54
57
57
#1
56
58
not supplied
(D-IO board)
not supplied
59
(AEP, UK)
#1
60
not supplied
M3000
CN701
#1
#1
not supplied
#1
#1
POWER board section
61
#1
Note: Refer to the Servicing Notes “NOTE OF HANDLING
THE DMB12 BOARD” (page 5), if replacing the Ref.
No.61.
not supplied
Part No.
Description
Ref. No.
Part No.
Description
51
51
52
53
54
A-1179-238-A
A-1179-611-A
1-828-576-11
1-833-129-11
1-833-126-11
MAIN BOARD, COMPLETE (US, CND)
MAIN BOARD, COMPLETE (AEP, UK)
WIRE (FLAT TYPE) (11 CORE)
WIRE (FLAT TYPE) (11 CORE)
WIRE (FLAT TYPE) (9 CORE) (US, CND)
0 58
59
* 60
61
1-783-820-11
1-500-386-11
3-703-244-00
A-1212-048-A
CORD, POWER (US, CND)
FILTER, CLAMP (FERRITE CORE) (AEP, UK)
BUSHING (2104), CORD
DMB12 BOARD, COMPLETE (for SERVICE)
(US, CND)
54
55
56
56
57
1-833-127-11
1-833-128-11
1-693-700-11
1-693-703-11
3-704-515-22
WIRE (FLAT TYPE) (11 CORE) (AEP, UK)
WIRE (FLAT TYPE) (11 CORE)
TUNER (FM/AM) (TM10SCE) (AEP, UK)
TUNER (FM/AM) (TM10SU) (US, CND)
SCREW (BV/RING)
61
Ref. No.
0 58
Remark
CN701
M3000
#1
Remark
A-1212-049-A DMB12 BOARD, COMPLETE (for SERVICE)
(AEP, UK)
1-818-086-41 HDMI CONNECTOR (HDMI OUT)
1-787-396-11 D.C. FAN (50 SQUARE)
7-685-871-01 SCREW +BVTT 3X6 (S)
1-777-071-23 CORD, POWER (AEP, UK)
99
HCD-X1V
8-3.
POWER BOARD SECTION
#1
not supplied
101
107
not supplied
not supplied
not supplied
101
107
104
101
DVD mechanism deck section
(CDM69EH)
#1
105
not supplied
#3
not supplied
#2
103
102
not supplied
F901
not supplied
not supplied
#1
#1
#2
not supplied
(LF board)
not supplied
#1
#2
#2
106
#2
#2
#2
#1
not supplied
not supplied
Ref. No.
Part No.
Description
101
102
103
103
104
3-077-331-21
1-828-659-11
A-1179-243-A
A-1179-614-A
1-828-621-11
+BV3 (3-CR)
WIRE (FLAT TYPE) (27 CORE)
POWER BOARD, COMPLETE (US, CND)
POWER BOARD, COMPLETE (AEP, UK)
WIRE (FLAT TYPE) (19 CORE)
105
105
106
A-1179-245-A AMP BOARD, COMPLETE (US, CND)
A-1179-616-A AMP BOARD, COMPLETE (AEP, UK)
4-977-358-01 CUSHION
100
#1
106
not supplied
Remark
Ref. No.
Part No.
107
0 F901
3-077-331-01 +BV3 (3-CR)
1-576-233-51 FUSE (H.B.C.) (T6.3AH/250V) (AEP, UK)
0 F901
1-576-537-12 FUSE, GLASS TUBE (DIA.5) (8A/125V)
(US, CND)
7-685-871-01 SCREW +BVTT 3X6 (S)
7-685-646-79 SCREW +BVTP 3X8 TYPE2 IT-3
7-685-872-09 SCREW +BVTT 3X8 (S)
#1
#2
#3
Description
Remark
HCD-X1V
8-4.
DVD MECHANISM DECK SECTION-1 (CDM69EH)
305
304
302
#7
301
S702
303
#7
#7
M761
306
303
313
312
not supplied
(ST ENCODER
board)
308
302
DVD mechanism deck section-2
309
RELAY board
310
302
307
#7
Ref. No.
Part No.
Description
Remark
301
302
303
304
305
1-686-725-13
3-087-053-01
4-239-690-01
4-239-618-01
4-239-676-01
STOCKER MOTOR BOARD
+BVTP2.6 (3CR)
CAM (STOCKER U/D)
SCREW (+PWH, 2X6), STEP TAPPING
STOCKER
306
307
4-239-687-01 GEAR (STOCKER COMMUNICATION)
A-4731-113-A RELAY BOARD, COMPLETE
(Including ST ENCODER BOARD)
Ref. No.
(including ST ENCODER board)
Part No.
Description
308
309
310
4-239-689-01 GEAR (STOCKER DECELERATION)
4-239-683-01 PULLEY (MODE DECELERATION)
4-211-237-01 BELT (MODE)
312
313
M761
S702
#7
4-986-156-01
1-763-967-11
A-4735-953-A
1-477-299-11
7-685-902-21
Remark
PULLEY, MOTOR
MOTOR, DC
MOTOR (STOCKER) ASSY (STOCKER)
ENCODER, ROTARY (STOCKER POSITION)
SCREW +PTPWH 2.6X8 (TYPE2)
101
HCD-X1V
8-5.
DVD MECHANISM DECK SECTION-2 (CDM69EH)
352
353
#8
354
355
355
351
DVD mechanism deck section-3
DVD mechanism deck section-4
356
optical pick-up
section
Ref. No.
351
352
353
354
102
Part No.
Description
1-686-727-13
1-686-728-13
1-686-729-13
1-686-730-13
SW (1) BOARD
SW (2) BOARD
SW (3) BOARD
SW (4) BOARD
Remark
Ref. No.
Part No.
Description
355
3-087-053-01 +BVTP2.6 (3CR)
356
#8
4-985-672-01 SCREW (+PTPWH M2.6), FLOATING
7-685-533-14 SCREW +BTP 2.6X6 TYPE2 N-S
Remark
HCD-X1V
8-6.
DVD MECHANISM DECK SECTION-3 (CDM69EH)
not supplied
406
not supplied
409
not supplied
407
405
411
422
409
not
supplied
413
402
421
420
415
412
401
414
405
not
supplied
415
417
416
not supplied
418
404
403
404
423
402
402
418
424
402
408
418
419
418
402
Ref. No.
Part No.
Description
401
402
403
404
405
4-240-040-01
4-992-069-01
4-239-648-11
4-239-646-01
4-239-641-01
SPRING (DISC STOPPER), TORSION
SCREW (+PTPWH) (M2) (DIA. 7)
PARASOL (ROLLER)
ROLLER (ROLLER)
SPRING (1.2), TENSION
406
407
408
409
411
4-239-642-01
4-239-679-01
2-345-860-01
4-239-649-01
4-244-035-01
SPRING (3), TENSION COIL
SPRING (5), TENSION COIL
PULLEY (A (310)), CHUCKING
PARASOL (STOCKER)
ROLLER (STOCKER), RUBBER
412
413
4-239-640-02 PINION (SLIDER)
4-243-291-01 SPRING, TORSION
Remark
Ref. No.
Part No.
Description
414
415
416
4-240-039-01 LEVER (DISC STOPPER)
4-239-702-01 ROLLER (DISC STOPPER)
4-985-672-01 SCREW (+PTPWH M2.6), FLOATING
417
418
419
420
421
4-243-713-01
4-239-647-01
4-243-916-01
4-241-599-01
4-243-703-02
422
423
424
4-239-643-01 SPRING (4), TENSION COIL
4-244-032-01 ROLLER, RUBBER
1-471-244-11 MAGNET
Remark
LEVER (LIFTER)
PARASOL (MAIN)
ROLLER (S), RUBBER
LEVER (SUPPORT)
YOKE (213)
103
HCD-X1V
8-7.
DVD MECHANISM DECK SECTION-4 (CDM69EH)
#6
#6
454
457
467
458
457
454
470
453
455
456
456
452
452
470
454
462
451
465
451
461
464
466
460
458
452
not supplied
461
#6
471
455
463
461
456
453
475
456
469
467
457
455
458
457
#6
468
453
#6
457
#6
473
466
461
454
472
not supplied
456
455
455
453
452
451
476
DVD mechanism deck section-5
Ref. No.
Part No.
Description
451
452
453
454
455
X-4954-626-1
4-239-666-01
4-239-668-01
4-239-652-02
4-239-669-01
LEVER (ROLLER) ASSY
GEAR
LEVER (CENTER)
SCREW (ROLLER), STEP
GEAR (ROLLER COMMUNICATION)
456
457
458
460
461
4-239-667-01
4-239-647-01
4-244-032-01
X-4954-622-1
4-239-670-01
GEAR (ROLLER CENTER)
PARASOL (MAIN)
ROLLER, RUBBER
BASE (SLIDER 2) ASSY
GEAR (ROLLER 5 COMMUNICATION)
462
463
464
465
X-4954-624-1
4-992-069-01
4-240-981-01
4-240-041-01
LEVER (SLIDER 4) ASSY
SCREW (+PTPWH) (M2) (DIA. 7)
SPRING (BASE SLIDER 5), TENSION
SPRING (SLIDER 2), TENSION
104
477
Remark
Ref. No.
Part No.
Description
466
3-087-053-01 +BVTP2.6 (3CR)
467
468
469
470
471
4-243-916-01
4-244-035-01
4-241-209-01
4-239-649-01
4-239-671-01
ROLLER (S), RUBBER
ROLLER (STOCKER), RUBBER
SHEET, ADHESIVE
PARASOL (STOCKER)
GEAR (ROLLER 5 CENTER)
472
473
475
476
477
X-4954-627-1
1-686-726-13
4-244-162-01
1-763-967-11
4-986-156-01
BASE (SLIDER 5) ASSY
ROLLER MOTOR BOARD
SPRING (SLIDER 4), TENSION
MOTOR, DC
PULLEY, MOTOR
M781
#6
A-4735-953-A MOTOR (STOCKER) ASSY (ROLLER)
7-623-921-01 RING, RETAINING, CAPSTAN
M781
Remark
HCD-X1V
8-8.
DVD MECHANISM DECK SECTION-5 (CDM69EH)
504
503
505
503
505
501
502
506
DVD mechanism deck section-6
507
509
508
Ref. No.
501
502
503
504
505
Part No.
Description
4-240-020-01
4-239-708-02
4-239-697-01
X-4955-157-1
4-239-706-02
GEAR (TIMING)
BELT (FRONT), TIMING
GEAR (CENTER)
SLIDER (MODE CAM V) ASSY
BELT (REAR), TIMING
Remark
Ref. No.
506
507
508
509
#7
#7
Part No.
Description
4-239-699-01
4-247-349-02
4-227-899-31
4-239-686-01
7-685-902-21
PULLEY
BELT (ROLLER V)
SCREW (DIA. 12), FLOATING
GEAR (ROLLER DECELERATION)
SCREW +PTPWH 2.6X8 (TYPE2)
Remark
105
HCD-X1V
8-9.
DVD MECHANISM DECK SECTION-6 (CDM69EH)
563
575
M771
568
not supplied
565
576
551
#7
#7
554
#7
555
#7
553
555
#7
564
569
558
572
570
not supplied
560
#7
557
562
563
559
#7
#7
#7
#7
552
566
567
#7
Ref. No.
563
561
571
Part No.
Description
551
552
553
554
555
4-239-693-02
1-686-723-13
4-239-696-01
4-239-695-02
4-240-019-01
CAM (GEAR)
SENSOR BOARD
GEAR (EJECT LOCK)
CAM (EJECT LOCK)
GEAR (MODE 5)
557
558
559
560
561
4-243-682-01
4-239-683-01
4-243-702-01
4-243-683-01
4-239-618-01
GEAR (MODE C)
PULLEY (MODE DECELERATION)
BELT (MODE V)
GEAR (MODE D)
SCREW (+PWH, 2X6), STEP TAPPING
562
563
564
565
4-243-681-01
3-087-053-01
4-239-692-02
4-239-694-01
GEAR (MODE B)
+BVTP2.6 (3CR)
CAM (BU U/D)
GEAR (MODE CAM)
106
S771
563
Remark
Ref. No.
Part No.
Description
566
4-241-731-01 SHUTTER (A), LEVER
567
568
569
570
571
4-241-732-01
1-763-967-11
4-241-734-01
4-241-735-01
4-985-672-01
SHUTTER (B), LEVER
MOTOR, DC
SHAFT (SHUTTER)
SPRING (SHUTTER), COMPRESSION
SCREW (+PTPWH M2.6), FLOATING
572
575
576
M771
S771
4-243-680-01
1-686-724-13
4-986-156-01
A-4735-953-A
1-477-300-11
GEAR (MODE A)
MODE MOTOR BOARD
PULLEY, MOTOR
MOTOR (STOCKER) ASSY (MODE)
ENCODER, ROTARY (MODE)
#7
7-685-902-21 SCREW +PTPWH 2.6X8 (TYPE2)
Remark
HCD-X1V
8-10. OPTICAL PICK-UP SECTION (KHM-310CAB or KHM-313CAB)
602
603
601
(including sled motor,
spindle motor)
not supplied
(sled motor)
602
602
603
603
not supplied
(spindle motor)
604
602
603
not supplied
Note: Refer to the Servicing Notes “HOW TO IDENTIFY
OPTICAL PICK-UP BLOCK” (page 7), if replacing
the Ref. No.601.
Ref. No.
Part No.
Description
Remark
0 601
8-820-291-02 OPTICAL PICK-UP BLOCK
0 601
(KHM-310CAB/C2RP)
(Including sled motor, spindle motor)
8-820-322-04 OPTICAL PICK-UP BLOCK
(KHM-313CAB/C2RP)
(Including sled motor, spindle motor)
Ref. No.
602
603
604
Part No.
Description
Remark
3-087-599-01 INSULATOR SCREW
3-088-372-01 INSULATOR
1-833-131-51 CABLE, FLEXIBLE FLAT (24 CORE)
107
HCD-X1V
SECTION 9
ELECTRICAL PARTS LIST
AMP
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Abbreviation
CND : Canadian model
Ref. No.
Part No.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA... : µA...
uPA... : µPA...
uPB... : µPB...
uPC... : µPC...
uPD... : µPD...
• CAPACITORS
uF: µF
• COILS
uH: µH
Description
Remark
A-1179-245-A AMP BOARD, COMPLETE (US, CND)
A-1179-616-A AMP BOARD, COMPLETE (AEP, UK)
********************
< CAPACITOR >
C3000
C3001
C3002
C3003
C3005
1-126-933-11
1-126-947-11
1-115-339-11
1-107-826-11
1-107-826-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
47uF
0.1uF
0.1uF
0.1uF
20%
20%
10%
10%
10%
16V
35V
50V
16V
16V
C3011
C3012
C3013
C3014
C3015
1-124-698-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
0.1uF
0.1uF
0.1uF
20%
10%
10%
10%
10%
25V
16V
16V
16V
16V
C3016
C3017
C3018
C3019
C3020
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C3021
C3022
C3023
C3024
C3025
1-124-698-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
0.1uF
0.1uF
0.1uF
20%
10%
10%
10%
10%
25V
16V
16V
16V
16V
C3026
C3027
C3028
C3029
C3030
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C3031
C3032
C3033
C3034
C3035
1-124-698-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
0.1uF
0.1uF
0.1uF
20%
10%
10%
10%
10%
25V
16V
16V
16V
16V
C3036
C3037
C3038
C3039
C3040
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C3051
C3052
C3053
C3054
1-107-826-11
1-126-933-11
1-162-964-11
1-126-933-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
0.1uF
100uF
0.001uF
100uF
10%
20%
10%
20%
16V
16V
50V
16V
108
Ref. No.
Part No.
The components identified by mark
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiquens pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
When indicating parts by reference
number, please include the board.
Description
Remark
C3055
1-162-970-11 CERAMIC CHIP
0.01uF
10%
25V
C3056
C3057
C3058
C3059
C3060
1-109-857-11
1-162-970-11
1-162-915-11
1-162-964-11
1-162-915-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
0.01uF
10PF
0.001uF
10PF
20%
10%
0.5PF
10%
0.5PF
63V
25V
50V
50V
50V
C3061
C3067
C3068
C3069
C3070
1-126-934-11
1-162-927-11
1-162-927-11
1-162-927-11
1-162-964-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220uF
100PF
100PF
100PF
0.001uF
20%
5%
5%
5%
10%
16V
50V
50V
50V
50V
C3071
C3100
C3101
C3103
C3104
1-107-826-11
1-107-826-11
1-100-703-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
10uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
25V
16V
16V
C3105
C3106
C3107
C3108
C3109
1-107-826-11
1-115-185-11
1-115-185-11
1-104-329-11
1-112-246-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
0.033uF
0.033uF
0.1uF
100uF
10%
10%
10%
10%
20%
16V
50V
50V
50V
35V
C3112
C3113
C3114
C3115
C3116
1-112-246-11
1-104-329-11
1-136-177-00
1-136-177-00
1-126-953-11
ELECT
CERAMIC CHIP
FILM
FILM
ELECT
100uF
0.1uF
1uF
1uF
2200uF
20%
10%
5%
5%
20%
35V
50V
50V
50V
35V
C3117
C3118
C3119
C3120
C3123
1-162-966-11
1-162-966-11
1-162-966-11
1-162-966-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.0022uF
0.0022uF
0.0022uF
2.2uF
10%
10%
10%
10%
50V
50V
50V
50V
16V
C3124
C3125
C3126
C3127
C3150
1-163-021-11
1-162-964-11
1-163-021-11
1-162-964-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.001uF
0.01uF
0.001uF
0.1uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
16V
C3151
C3153
C3154
C3155
C3156
1-100-703-11
1-107-826-11
1-107-826-11
1-107-826-11
1-115-185-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.1uF
0.1uF
0.1uF
0.033uF
10%
10%
10%
10%
10%
25V
16V
16V
16V
50V
C3157
C3158
1-115-185-11 CERAMIC CHIP
1-104-329-11 CERAMIC CHIP
0.033uF
0.1uF
10%
10%
50V
50V
HCD-X1V
AMP
Ref. No.
Part No.
Description
Remark
C3159
C3162
C3163
1-112-246-11 ELECT
1-112-246-11 ELECT
1-104-329-11 CERAMIC CHIP
100uF
100uF
0.1uF
20%
20%
10%
35V
35V
50V
C3164
C3165
C3166
C3167
C3168
1-136-177-00
1-136-177-00
1-126-953-11
1-162-966-11
1-162-966-11
FILM
FILM
ELECT
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
2200uF
0.0022uF
0.0022uF
5%
5%
20%
10%
10%
50V
50V
35V
50V
50V
C3169
C3170
C3173
C3174
C3175
1-162-966-11
1-162-966-11
1-164-505-11
1-163-021-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.0022uF
2.2uF
0.01uF
0.001uF
10%
10%
10%
10%
50V
50V
16V
50V
50V
C3176
C3177
C3200
C3201
C3203
1-163-021-11
1-162-964-11
1-107-826-11
1-100-703-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.001uF
0.1uF
10uF
0.1uF
10%
10%
10%
10%
10%
50V
50V
16V
25V
16V
C3204
C3205
C3206
C3207
C3208
1-107-826-11
1-107-826-11
1-115-185-11
1-115-185-11
1-104-329-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.033uF
0.033uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
50V
50V
50V
C3209
C3212
C3213
C3214
C3215
1-112-246-11
1-112-246-11
1-104-329-11
1-135-621-51
1-135-621-51
ELECT
ELECT
CERAMIC CHIP
FILM
FILM
100uF
100uF
0.1uF
2.2uF
2.2uF
20%
20%
10%
5%
5%
35V
35V
50V
50V
50V
C3216
C3217
C3218
C3219
C3220
1-126-953-11
1-162-966-11
1-162-966-11
1-162-966-11
1-162-966-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2200uF
0.0022uF
0.0022uF
0.0022uF
0.0022uF
20%
10%
10%
10%
10%
35V
50V
50V
50V
50V
C3223
C3224
C3225
C3226
C3227
1-117-370-11
1-163-021-11
1-162-964-11
1-163-021-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.01uF
0.001uF
0.01uF
0.001uF
10%
10%
10%
10%
10V
50V
50V
50V
50V
C3250
C3251
C3253
C3254
C3255
1-107-826-11
1-100-703-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
25V
16V
16V
16V
C3256
C3257
C3258
C3259
C3262
1-115-185-11
1-115-185-11
1-104-329-11
1-112-246-11
1-112-246-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.033uF
0.033uF
0.1uF
100uF
100uF
10%
10%
10%
20%
20%
50V
50V
50V
35V
35V
C3263
C3264
C3265
C3266
C3267
1-104-329-11
1-135-621-51
1-135-621-51
1-126-953-11
1-162-966-11
CERAMIC CHIP
FILM
FILM
ELECT
CERAMIC CHIP
0.1uF
2.2uF
2.2uF
2200uF
0.0022uF
10%
5%
5%
20%
10%
50V
50V
50V
35V
50V
C3268
C3269
C3270
C3273
C3274
1-162-966-11
1-162-966-11
1-162-966-11
1-117-370-11
1-163-021-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.0022uF
0.0022uF
10uF
0.01uF
10%
10%
10%
50V
50V
50V
10V
50V
10%
Ref. No.
Part No.
Description
Remark
C3275
C3276
C3277
C3300
C3301
1-162-964-11
1-163-021-11
1-162-964-11
1-107-826-11
1-100-703-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.01uF
0.001uF
0.1uF
10uF
10%
10%
10%
10%
10%
50V
50V
50V
16V
25V
C3303
C3304
C3305
C3306
C3307
1-107-826-11
1-107-826-11
1-107-826-11
1-115-185-11
1-115-185-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.033uF
0.033uF
10%
10%
10%
10%
10%
16V
16V
16V
50V
50V
C3308
C3309
C3312
C3313
C3314
1-104-329-11
1-112-246-11
1-112-246-11
1-104-329-11
1-136-177-00
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
FILM
0.1uF
100uF
100uF
0.1uF
1uF
10%
20%
20%
10%
5%
50V
35V
35V
50V
50V
C3315
C3316
C3317
C3318
C3319
1-136-177-00
1-126-953-11
1-162-966-11
1-162-966-11
1-162-966-11
FILM
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
2200uF
0.0022uF
0.0022uF
0.0022uF
5%
20%
10%
10%
10%
50V
35V
50V
50V
50V
C3320
C3323
C3324
C3325
C3326
1-162-966-11
1-164-505-11
1-163-021-11
1-162-964-11
1-163-021-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
2.2uF
0.01uF
0.001uF
0.01uF
10%
10%
10%
10%
50V
16V
50V
50V
50V
C3327
C3350
C3351
C3353
C3354
1-162-964-11
1-107-826-11
1-100-703-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.1uF
10uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
50V
16V
25V
16V
16V
C3355
C3356
C3357
C3358
C3359
1-107-826-11
1-115-185-11
1-115-185-11
1-104-329-11
1-112-246-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
0.033uF
0.033uF
0.1uF
100uF
10%
10%
10%
10%
20%
16V
50V
50V
50V
35V
C3362
C3363
C3364
C3365
C3366
1-112-246-11
1-104-329-11
1-136-177-00
1-136-177-00
1-126-953-11
ELECT
CERAMIC CHIP
FILM
FILM
ELECT
100uF
0.1uF
1uF
1uF
2200uF
20%
10%
5%
5%
20%
35V
50V
50V
50V
35V
C3367
C3368
C3369
C3370
C3373
1-162-966-11
1-162-966-11
1-162-966-11
1-162-966-11
1-164-505-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.0022uF
0.0022uF
0.0022uF
2.2uF
10%
10%
10%
10%
50V
50V
50V
50V
16V
C3374
C3375
C3376
C3377
C3500
1-163-021-11
1-162-964-11
1-163-021-11
1-162-964-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.001uF
0.01uF
0.001uF
0.1uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
16V
C3501
C3551
C3552
C3555
C3603
1-126-933-11
1-126-960-11
1-126-964-11
1-164-004-11
1-107-826-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
100uF
1uF
10uF
0.1uF
0.1uF
20%
20%
20%
10%
10%
16V
50V
50V
25V
16V
C3604
C3610
1-107-826-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
0.1uF
0.1uF
10%
10%
16V
16V
109
HCD-X1V
AMP
Ref. No.
Part No.
Description
Remark
C3801
C3903
C3904
1-115-339-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
0.1uF
0.1uF
0.1uF
10%
10%
10%
50V
16V
16V
C3905
1-100-566-91 CERAMIC CHIP
0.1uF
10%
25V
< CONNECTOR >
CN3000 1-564-704-41 PIN, CONNECTOR (SMALL TYPE) 2P
CN3500 1-820-403-11 SOCKET, D-SUB CONNECTOR 15P (SPEAKAER)
CN3700 1-778-691-51 CONNECTOR, FFC/FPC 19P
< DIODE >
D3111
D3112
D3151
D3152
D3201
6-500-260-01
6-500-260-01
6-500-260-01
6-500-260-01
6-500-260-01
DIODE
DIODE
DIODE
DIODE
DIODE
P6SMB39AT3
P6SMB39AT3
P6SMB39AT3
P6SMB39AT3
P6SMB39AT3
D3202
D3251
D3252
D3301
D3302
6-500-260-01
6-500-260-01
6-500-260-01
6-500-260-01
6-500-260-01
DIODE
DIODE
DIODE
DIODE
DIODE
P6SMB39AT3
P6SMB39AT3
P6SMB39AT3
P6SMB39AT3
P6SMB39AT3
D3351
D3352
D3551
D3552
6-500-260-01
6-500-260-01
6-501-193-01
6-501-193-01
DIODE
DIODE
DIODE
DIODE
P6SMB39AT3
P6SMB39AT3
1SS355WTE-17
1SS355WTE-17
< JUMPER RESISTOR >
Ref. No.
Part No.
Description
Remark
L3152
L3171
1-456-680-11 CHOKE, COIL
1-457-077-11 AIR-CORE COIL
10uH
L3172
L3200
L3201
L3202
L3221
1-457-078-11
1-414-754-11
1-456-680-11
1-456-680-11
1-457-077-11
AIR-CORE COIL
INDUCTOR
CHOKE, COIL
CHOKE, COIL
AIR-CORE COIL
10uH
10uH
10uH
L3222
L3250
L3251
L3252
L3271
1-457-078-11
1-414-754-11
1-456-680-11
1-456-680-11
1-457-077-11
AIR-CORE COIL
INDUCTOR
CHOKE, COIL
CHOKE, COIL
AIR-CORE COIL
10uH
10uH
10uH
L3272
L3300
L3301
L3302
L3321
1-457-078-11
1-414-754-11
1-456-680-11
1-456-680-11
1-457-077-11
AIR-CORE COIL
INDUCTOR
CHOKE, COIL
CHOKE, COIL
AIR-CORE COIL
10uH
10uH
10uH
L3322
L3350
L3351
L3352
L3371
1-457-078-11
1-414-754-11
1-456-680-11
1-456-680-11
1-457-077-11
AIR-CORE COIL
INDUCTOR
CHOKE, COIL
CHOKE, COIL
AIR-CORE COIL
10uH
10uH
10uH
L3372
1-457-078-11 AIR-CORE COIL
< TRANSISTOR >
< IC >
Q3000
Q3001
Q3002
Q3121
Q3122
8-729-142-48
8-729-120-28
8-729-120-28
8-729-600-22
8-729-600-22
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD1616-TP-LK
2SC1623-L5L6
2SC1623-L5L6
2SA1235-F
2SA1235-F
FB3051 1-216-295-00 SHORT CHIP
0
IC3010
IC3020
IC3030
IC3050
IC3051
6-709-035-01
6-709-035-01
6-709-035-01
6-702-300-01
8-759-649-50
IC
IC
IC
IC
IC
CXD9876R
CXD9876R
CXD9876R
TK11118CSCL-G
SN74AHC1GU04DCKR
Q3171
Q3172
Q3221
Q3222
Q3271
8-729-600-22
8-729-600-22
8-729-600-22
8-729-600-22
8-729-600-22
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1235-F
2SA1235-F
2SA1235-F
2SA1235-F
2SA1235-F
IC3100
IC3150
IC3200
IC3250
IC3300
6-708-921-01
6-708-921-01
6-708-921-01
6-708-921-01
6-708-921-01
IC
IC
IC
IC
IC
CXD9883M
CXD9883M
CXD9883M
CXD9883M
CXD9883M
Q3272
Q3301
Q3302
Q3371
Q3372
8-729-600-22
8-729-600-22
8-729-600-22
8-729-600-22
8-729-600-22
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SA1235-F
2SA1235-F
2SA1235-F
2SA1235-F
2SA1235-F
IC3350
IC3500
6-708-921-01 IC CXD9883M
8-759-573-97 IC SN74LVC541APWR
Q3551
8-729-120-28 TRANSISTOR
2SC1623-L5L6
< RESISTOR >
< COIL >
R3001
R3002
R3003
R3004
R3006
1-216-833-11
1-216-833-11
1-216-823-11
1-216-822-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
1.5K
1.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
10uH
10uH
10uH
10uH
R3007
R3011
R3012
R3013
R3014
1-216-864-11
1-216-817-11
1-216-817-11
1-216-833-11
1-216-809-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
470
470
10K
100
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1-216-815-11
1-216-811-11
1-216-864-11
1-216-817-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
330
150
0
470
5%
5%
1/10W
1/10W
10uH
10uH
R3015
R3017
R3018
R3021
5%
1/10W
L3000
L3051
L3052
L3053
L3054
1-414-754-11
1-414-754-11
1-414-754-11
1-414-754-11
1-412-939-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
10uH
10uH
10uH
1uH
L3055
L3100
L3111
L3112
L3121
1-414-754-11
1-414-754-11
1-456-680-11
1-456-680-11
1-457-077-11
INDUCTOR
INDUCTOR
CHOKE, COIL
CHOKE, COIL
AIR-CORE COIL
L3122
L3150
L3151
1-457-078-11 AIR-CORE COIL
1-414-754-11 INDUCTOR
1-456-680-11 CHOKE, COIL
110
HCD-X1V
AMP
Ref. No.
Part No.
Description
Remark
R3023
1-216-833-11 METAL CHIP
10K
5%
1/10W
R3024
R3025
R3027
R3031
R3032
1-216-809-11
1-216-815-11
1-216-811-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
330
150
470
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3034
R3035
R3037
R3051
R3052
1-216-809-11
1-216-815-11
1-216-811-11
1-216-864-11
1-216-857-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
100
330
150
0
1M
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R3053
R3054
R3055
R3056
R3059
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3060
R3063
R3064
R3065
R3066
1-216-833-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
1K
1K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3067
R3068
R3069
R3070
R3071
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3072
R3073
R3074
R3075
R3076
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3078
R3101
R3102
R3103
R3104
1-216-864-11
1-216-809-11
1-216-809-11
1-216-797-11
1-216-864-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
0
100
100
10
0
5%
5%
5%
1/10W
1/10W
1/10W
R3107
R3115
R3116
R3119
R3120
1-216-835-11
1-216-797-11
1-216-797-11
1-216-790-11
1-216-790-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
10
10
2.7
2.7
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3125
R3126
R3127
R3151
R3152
1-216-845-11
1-216-845-11
1-216-845-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3153
R3154
R3157
R3165
R3166
1-216-797-11
1-216-864-11
1-216-835-11
1-216-797-11
1-216-797-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10
0
15K
10
10
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
R3169
R3170
R3175
R3176
R3177
1-216-790-11
1-216-790-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.7
2.7
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3201
1-216-809-11 METAL CHIP
100
5%
1/10W
Ref. No.
Part No.
Description
R3202
R3203
R3204
R3207
1-216-809-11
1-216-797-11
1-216-864-11
1-216-835-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
100
10
0
15K
5%
5%
Remark
1/10W
1/10W
5%
1/10W
R3215
R3216
R3219
R3220
R3225
1-216-797-11
1-216-797-11
1-216-790-11
1-216-790-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10
10
2.7
2.7
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3226
R3227
R3251
R3252
R3253
1-216-845-11
1-216-845-11
1-216-809-11
1-216-809-11
1-216-797-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100
100
10
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3254
R3257
R3265
R3266
R3269
1-216-864-11
1-216-835-11
1-216-797-11
1-216-797-11
1-216-790-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
15K
10
10
2.7
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R3270
R3275
R3276
R3277
R3301
1-216-790-11
1-216-845-11
1-216-845-11
1-216-845-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.7
100K
100K
100K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3302
R3303
R3304
R3307
R3315
1-216-809-11
1-216-797-11
1-216-864-11
1-216-835-11
1-216-797-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
100
10
0
15K
10
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
R3316
R3319
R3320
R3325
R3326
1-216-797-11
1-216-790-11
1-216-790-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10
2.7
2.7
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3327
R3351
R3352
R3353
R3354
1-216-845-11
1-216-809-11
1-216-809-11
1-216-797-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
100K
100
100
10
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R3357
R3365
R3366
R3369
R3370
1-216-835-11
1-216-797-11
1-216-797-11
1-216-790-11
1-216-790-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
10
10
2.7
2.7
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3375
R3376
R3377
R3502
R3503
1-216-845-11
1-216-845-11
1-216-845-11
1-216-797-11
1-216-797-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
10
10
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3504
R3505
R3506
R3507
R3551
1-216-797-11
1-216-797-11
1-216-797-11
1-216-797-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10
10
10
10
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R3553
R3554
R3555
R3601
1-216-833-11
1-216-845-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
10K
100K
0
0
5%
5%
1/10W
1/10W
111
HCD-X1V
AMP
Ref. No.
AUDIO IN
Part No.
D-IO
DISPLAY
Description
Remark
R3602
1-216-864-11 SHORT CHIP
0
R3605
1-216-864-11 SHORT CHIP
0
Ref. No.
IC1004
Part No.
J1000
1-818-314-11 PIN JACK 2P (DIGITAL IN VIDEO1 COAXIAL,
VIDEO2 COAXIAL)
X3051 1-795-660-21 QUARTZ CRYSTAL UNIT (49.152MHz)
************************************************************
AUDIO IN BOARD
**************
< RESISTOR >
R1000
R1001
R1002
R1003
R1004
1-216-864-11
1-216-864-11
1-218-285-11
1-218-285-11
1-216-809-11
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
75
75
100
5%
5%
5%
1/10W
1/10W
1/10W
R1005
R1007
R1008
R1009
R1010
1-216-833-11
1-216-817-11
1-216-853-11
1-216-841-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
470
470K
47K
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
R1011
R1012
R1013
R1014
R1015
1-216-853-11
1-216-809-11
1-216-841-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470K
100
47K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< JACK >
R1016
1-216-864-11 SHORT CHIP
< CAPACITOR >
1-162-970-11 CERAMIC CHIP
0.01uF
10%
25V
< CONNECTOR >
* CN808
Remark
< JACK >
< VIBRATOR >
C836
Description
8-759-236-19 IC TC74HC151AF (EL)
1-564-720-11 PIN, CONNECTOR (SMALL TYPE) 4P
< FERRITE BEAD >
FB803
FB804
FB805
FB806
1-414-760-21
1-414-760-21
1-414-760-21
1-414-760-21
J801
1-566-891-21 JACK (AUDIO IN)
************************************************************
< SWITCH >
S1000 1-771-692-11 SWITCH, SLIDE (DIGITAL INPUT SELECT)
************************************************************
D-IO BOARD
**********
A-1179-254-A DISPLAY BOARD, COMPLETE (US, CND)
A-1179-625-A DISPLAY BOARD, COMPLETE (AEP, UK)
************************
< CAPACITOR >
C1000
C1001
C1003
C1004
C1005
1-107-826-11
1-107-826-11
1-126-395-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
22uF
0.1uF
0.1uF
10%
10%
20%
10%
10%
16V
16V
16V
16V
16V
C1006
C1007
C1009
C1010
1-107-826-11
1-126-204-11
1-107-826-11
1-126-204-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
0.1uF
47uF
0.1uF
47uF
10%
20%
10%
20%
16V
16V
16V
16V
< CONNECTOR >
* CN1000 1-568-934-11 PIN, CONNECTOR 7P
< JUMPER RESISTOR >
FB1000 1-216-864-11 SHORT CHIP
FB1001 1-216-864-11 SHORT CHIP
0
0
0
< CAPACITOR >
C800
C801
C802
C803
C804
1-162-968-11
1-163-037-11
1-119-943-11
1-124-584-00
1-162-974-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
0.0047uF
0.022uF
47uF
100uF
0.01uF
10%
10%
20%
20%
50V
50V
50V
10V
50V
C805
C808
C809
C810
C811
1-164-360-11
1-162-974-11
1-162-923-11
1-162-974-11
1-162-966-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
47PF
5%
0.01uF
0.0022uF 10%
16V
50V
50V
50V
50V
C812
C813
C814
C815
C828
1-162-927-11
1-162-927-11
1-164-360-11
1-117-370-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
0.1uF
10uF
0.01uF
10%
50V
50V
16V
10V
25V
C829
1-126-205-11 ELECT CHIP
47uF
20%
6.3V
5%
5%
< FILTER >
FL1000 1-234-177-21 FILTER, CHIP EMI
FL1001 1-234-177-21 FILTER, CHIP EMI
< IC >
IC1000
IC1001
IC1003
112
6-600-466-01 IC TORX147L (SONY)
(DIGITAL IN TV OPTICAL)
6-600-466-01 IC TORX147L (SONY)
(DIGITAL IN VIDEO1 OPTICAL)
8-759-233-64 IC TC74HCU04AF
< CONNECTOR >
CN801
CN803
1-784-871-51 CONNECTOR, FFC (LIF (NON-ZIF)) 19P
1-784-860-51 CONNECTOR, FFC (LIF (NON-ZIF)) 8P
< DIODE >
D801
D802
8-719-988-61 DIODE 1SS355TE-17
8-719-988-61 DIODE 1SS355TE-17
HCD-X1V
DISPLAY
Ref. No.
Part No.
Description
Remark
D803
D804
D805
8-719-069-56 DIODE UDZSTE-176.2B
8-719-988-61 DIODE 1SS355TE-17
8-719-988-61 DIODE 1SS355TE-17
D817
D818
D819
8-719-045-55 LED SEC1201C (FOCUS SUR)
8-719-045-55 LED SEC1201C (WIDE SUR)
8-719-045-55 LED SEC1201C (2CH STEREO)
Ref. No.
Description
Remark
< TRANSFORMER >
T801
1-443-757-11 TRANSFORMER, DC-DC CONVERTER
************************************************************
A-1212-048-A DMB12 BOARD, COMPLETE (for SERVICE)
(US, CND)
A-1212-049-A DMB12 BOARD, COMPLETE (for SERVICE)
(AEP, UK)
**********************
< EARTH TERMINAL >
EB807
Part No.
DMB12
1-537-738-21 TERMINAL, GROUND
< CAPACITOR >
< JUMPER RESISTOR >
FB801
FB802
1-216-295-00 SHORT CHIP
1-216-295-00 SHORT CHIP
0
0
< FLUORESCENT INDICATOR TUBE >
FL801
1-5198-601-A FLUORESCENT INDICATOR
< IC >
IC801
IC803
6-600-349-21 IC NJL23H400A
6-705-899-01 IC ML9208-03MBZ03B
< COIL/JUMPER RESISTOR >
L801
L802
L803
L804
1-410-671-31
1-216-295-00
1-216-295-00
1-216-295-00
INDUCTOR
SHORT CHIP
SHORT CHIP
SHORT CHIP
47uH
0
0
0
< TRANSISTOR >
Q801
Q802
Q817
Q818
Q819
6-550-065-01
8-729-120-28
8-729-027-43
8-729-027-43
8-729-027-43
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
CPH5504-TL-E
2SC1623-L5L6
DTC114EKA-T146
DTC114EKA-T146
DTC114EKA-T146
< RESISTOR >
C101
C102
C105
C106
C112
1-162-970-11
1-125-837-11
1-128-994-21
1-162-970-11
1-128-994-21
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
0.01uF
1uF
47uF
0.01uF
47uF
10%
10%
20%
10%
20%
25V
6.3V
10V
25V
10V
C113
C114
C115
C116
C117
1-162-970-11
1-107-826-11
1-107-826-11
1-107-826-11
1-124-779-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.01uF
0.1uF
0.1uF
0.1uF
10uF
10%
10%
10%
10%
20%
25V
16V
16V
16V
16V
C118
C119
C120
C121
C122
1-124-779-00
1-124-779-00
1-165-908-11
1-165-908-11
1-165-908-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
10uF
1uF
1uF
1uF
20%
20%
10%
10%
10%
16V
16V
10V
10V
10V
C123
C124
C125
C126
C127
1-165-908-11
1-165-908-11
1-107-826-11
1-107-826-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
0.1uF
0.1uF
0.01uF
10%
10%
10%
10%
10%
10V
10V
16V
16V
25V
C128
C130
C131
C132
C133
1-162-965-11
1-107-826-11
1-125-889-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0015uF
0.1uF
2.2uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
50V
16V
10V
16V
16V
1-164-677-11
1-162-970-11
1-107-826-11
1-162-964-11
1-162-919-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.033uF
0.01uF
0.1uF
0.001uF
22PF
10%
10%
10%
10%
5%
16V
25V
16V
50V
50V
R801
R802
R804
R805
R814
1-216-839-11
1-216-809-11
1-216-828-11
1-216-295-00
1-216-827-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
33K
100
3.9K
0
3.3K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
C135
C136
C137
C138
C139
R815
R816
R817
R820
R821
1-216-809-11
1-216-809-11
1-216-809-11
1-216-833-11
1-216-805-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
10K
47
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C140
C141
C142
C143
C144
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.01uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
25V
R846
R851
R854
R861
R867
1-216-809-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-811-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
1K
1K
1K
150
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C145
C147
C148
C149
C150
1-165-908-11
1-165-176-11
1-165-176-11
1-107-826-11
1-124-779-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
1uF
0.047uF
0.047uF
0.1uF
10uF
10%
10%
10%
10%
20%
10V
16V
16V
16V
16V
R868
R869
R872
R875
1-216-811-11
1-216-811-11
1-216-821-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
150
150
1K
100K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
C151
C152
C153
C154
C155
1-162-964-11
1-162-917-11
1-162-917-11
1-107-826-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
15PF
15PF
0.1uF
0.01uF
10%
5%
5%
10%
10%
50V
50V
50V
16V
25V
C156
C157
1-162-970-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
0.01uF
0.01uF
10%
10%
25V
25V
Note: When the DMB12 board is replaced by a repair for a fee, throw away the DMB12
board after obtaining consent of not returning of the DMB12 board to the
customer. When throwing away the DMB12 board, be sure to throw away after
destroying EEPROM (IC103 and IC706) physically with the hammer etc.
113
HCD-X1V
DMB12
Ref. No.
Part No.
Description
Remark
C158
C160
C161
1-162-970-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
0.01uF
0.01uF
0.01uF
10%
10%
10%
25V
25V
25V
C162
C163
C164
C171
C172
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C173
C174
C175
C176
C177
1-162-964-11
1-162-970-11
1-162-970-11
1-162-970-11
1-128-994-21
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.001uF
0.01uF
0.01uF
0.01uF
47uF
10%
10%
10%
10%
20%
50V
25V
25V
25V
10V
C179
C180
C181
C182
C183
1-107-826-11
1-107-826-11
1-107-826-11
1-127-715-11
1-128-934-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.22uF
0.33uF
10%
10%
10%
10%
20%
16V
16V
16V
16V
10V
C184
C186
C187
C190
C191
1-162-970-11
1-127-715-11
1-126-208-21
1-128-994-21
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
0.01uF
0.22uF
47uF
47uF
0.1uF
10%
10%
20%
20%
10%
25V
16V
4V
10V
16V
C192
C193
C195
C197
C198
1-162-970-11
1-127-715-11
1-127-715-11
1-107-826-11
1-165-908-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.22uF
0.22uF
0.1uF
1uF
10%
10%
10%
10%
10%
25V
16V
16V
16V
10V
C199
C203
C205
C206
C208
1-162-968-11
1-162-970-11
1-164-230-11
1-164-230-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
0.01uF
220PF
220PF
0.01uF
10%
10%
5%
5%
10%
50V
25V
50V
50V
25V
C209
C210
C211
C212
C213
1-164-677-11
1-162-970-11
1-164-677-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.033uF
0.01uF
0.033uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
16V
25V
16V
25V
25V
C214
C215
C217
C218
C219
1-162-964-11
1-162-970-11
1-126-204-11
1-124-779-00
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
0.001uF
0.01uF
47uF
10uF
0.01uF
10%
10%
20%
20%
10%
50V
25V
16V
16V
25V
C220
C221
C222
C224
C233
1-124-779-00
1-107-826-11
1-107-826-11
1-162-970-11
1-162-968-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.1uF
0.1uF
0.01uF
0.0047uF
20%
10%
10%
10%
10%
16V
16V
16V
25V
50V
C602
C603
C701
C702
C703
1-128-994-21
1-128-994-21
1-107-826-11
1-107-826-11
1-162-970-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
47uF
0.1uF
0.1uF
0.01uF
20%
20%
10%
10%
10%
10V
10V
16V
16V
25V
C704
C707
C709
C710
C711
1-107-826-11
1-128-993-21
1-107-826-11
1-124-779-00
1-107-826-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
22uF
0.1uF
10uF
0.1uF
10%
20%
10%
20%
10%
16V
10V
16V
16V
16V
114
Ref. No.
Part No.
Description
Remark
C712
C713
C714
C715
C716
1-107-826-11
1-164-172-11
1-107-826-11
1-128-994-21
1-127-715-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
0.0056uF
0.1uF
47uF
0.22uF
10%
10%
10%
20%
10%
16V
25V
16V
10V
16V
C717
C718
C719
C720
C723
1-162-970-11
1-162-970-11
1-127-715-11
1-127-715-11
1-127-715-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.22uF
0.22uF
0.22uF
10%
10%
10%
10%
10%
25V
25V
16V
16V
16V
C725
C726
C727
C729
C730
1-162-970-11
1-107-826-11
1-162-970-11
1-127-715-11
1-127-715-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.01uF
0.22uF
0.22uF
10%
10%
10%
10%
10%
25V
16V
25V
16V
16V
C731
C732
C733
C734
C736
1-128-993-21
1-162-970-11
1-162-970-11
1-162-970-11
1-126-208-21
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
22uF
0.01uF
0.01uF
0.01uF
47uF
20%
10%
10%
10%
20%
10V
25V
25V
25V
4V
C1103
C1104
C1105
C1106
C1107
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C1501
C4501
C4502
C4504
1-162-970-11
1-117-370-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
10uF
0.01uF
0.01uF
10%
25V
10V
25V
25V
10%
10%
< CONNECTOR >
CN101
* CN105
CN109
* CN201
CN601
1-815-763-32
1-770-470-21
1-784-370-51
1-770-470-21
1-779-993-11
CONNECTOR, FFC/FPC 24P
PIN, CONNECTOR (PC BOARD) 6P
CONNECTOR, FFC/FPC 11P
PIN, CONNECTOR (PC BOARD) 6P
PIN, CONNECTOR (PWB) 5P
CN701 1-818-086-41 HDMI CONNECTOR (HDMI OUT)
CN4301 1-784-370-51 CONNECTOR, FFC/FPC 11P
CN4501 1-784-370-51 CONNECTOR, FFC/FPC 11P
< FERRITE BEAD >
FB106
FB107
FB108
FB111
FB112
1-469-324-21
1-469-324-21
1-469-324-21
1-469-670-21
1-469-670-21
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
FB115
FB123
FB601
FB602
FB603
1-469-670-21
1-469-324-21
1-469-324-21
1-469-324-21
1-469-324-21
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
FB604
FB605
FB606
1-469-324-21 FERRITE, EMI (SMD) (2012)
1-469-324-21 FERRITE, EMI (SMD) (2012)
1-469-324-21 FERRITE, EMI (SMD) (2012)
< FILTER >
FL601
1-234-177-21 FILTER, CHIP EMI
HCD-X1V
DMB12
Ref. No.
FL602
FL603
FL701
FL703
Part No.
Description
1-233-893-21
1-234-177-21
1-234-177-21
1-234-177-21
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
Remark
FL704 1-234-177-21 FILTER, CHIP EMI
FL705 1-234-177-21 FILTER, CHIP EMI
FL4501 1-234-177-21 FILTER, CHIP EMI
< IC >
IC101
IC102
IC102
IC103
IC104
6-706-727-01
6-806-717-01
6-806-718-01
(Not supplied)
6-707-897-01
IC
IC
IC
IC
IC
CXD9804R
S29AL032D70TF-CHE2-0611UC (US, CND)
S29AL032D70TF-CHE2-0611CE (AEP, UK)
BR24L64F-WE2
EDS6416AHTA-75-E
IC105
IC107
IC110
* IC111
IC150
6-702-302-01
6-702-302-01
6-707-739-01
6-704-100-01
8-759-592-47
IC
IC
IC
IC
IC
TK11133CSCL-G
TK11133CSCL-G
MM1661JTRE
TC7PAU04FU (TE85R)
TC7SZ08FU (TE85R)
IC201
IC701
IC702
IC703
IC705
6-704-524-01
6-708-682-01
6-702-300-01
6-702-302-01
8-759-592-47
IC
IC
IC
IC
IC
FAN8036L
CXD9873Q
TK11118CSCL-G
TK11133CSCL-G
TC7SZ08FU (TE85R)
IC706
IC707
IC708
IC4501
IC4502
(Not supplied)
6-705-337-01
6-806-298-01
8-759-573-97
8-759-592-49
IC
IC
IC
IC
IC
BR24L16F-WE2
TK11150CSCL-G
MB95F108ASPFV-GE1-H0601
SN74LVC541APWR
TC7SZ125FU (TE85R)
< COIL >
*
*
*
*
LF701
LF702
LF703
LF704
1-813-308-11
1-813-308-11
1-813-308-11
1-813-308-11
COMMON MODE CHOKE
COMMON MODE CHOKE
COMMON MODE CHOKE
COMMON MODE CHOKE
Ref. No.
Part No.
Description
Remark
R117
R118
R120
R121
R123
1-216-841-11
1-216-801-11
1-216-801-11
1-216-801-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
47K
22
22
22
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R124
R126
R130
R132
R133
1-216-841-11
1-216-829-11
1-162-970-11
1-216-845-11
1-216-864-11
METAL CHIP
METAL CHIP
CERAMIC CHIP
METAL CHIP
SHORT CHIP
47K
4.7K
0.01uF
100K
0
5%
5%
10%
5%
1/10W
1/10W
25V
1/10W
R135
R136
R138
R139
R140
1-216-833-11
1-216-835-11
1-216-809-11
1-216-864-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
10K
15K
100
0
10K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R141
R142
R143
R145
R146
1-216-855-11
1-216-845-11
1-216-805-11
1-216-864-11
1-216-805-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
680K
100K
47
0
47
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R147
R148
R151
R152
R153
1-216-864-11
1-216-864-11
1-216-833-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
0
0
10K
0
0
5%
1/10W
R154
R155
R156
R159
R160
1-216-864-11
1-216-864-11
1-216-809-11
1-216-805-11
1-216-805-11
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
100
47
47
5%
5%
5%
1/10W
1/10W
1/10W
R161
R162
R163
R164
R165
1-216-805-11
1-216-864-11
1-469-118-21
1-216-864-11
1-469-118-21
METAL CHIP
47
5%
SHORT CHIP
0
FERRITE, EMI (SMD) (1608)
SHORT CHIP
0
FERRITE, EMI (SMD) (1608)
1/10W
R166
R167
R169
R170
R171
1-216-864-11
1-469-118-21
1-216-864-11
1-216-833-11
1-216-809-11
SHORT CHIP
0
FERRITE, EMI (SMD) (1608)
SHORT CHIP
0
METAL CHIP
10K
5%
METAL CHIP
100
5%
1/10W
1/10W
R172
R173
R174
R175
R183
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-805-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
0
0
0
0
47
5%
1/10W
R184
R185
R189
R190
R191
1-216-805-11
1-216-805-11
1-218-827-11
1-218-827-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47
47
150
150
1K
5%
5%
0.5%
0.5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R192
R193
R195
R197
R204
1-218-827-11
1-216-821-11
1-218-827-11
1-218-827-11
1-216-822-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
150
1K
150
150
1.2K
0.5%
5%
0.5%
0.5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R205
R206
1-216-833-11 METAL CHIP
1-216-833-11 METAL CHIP
10K
10K
5%
5%
1/10W
1/10W
< TRANSISTOR >
Q101
Q102
Q103
Q701
Q702
6-550-008-01
6-550-653-01
8-729-027-52
8-729-012-57
8-729-012-57
FET
TRANSISTOR
TRANSISTOR
FET
FET
UM6K1N-TN
QST8TR
DTC124EKA-T146
2SK1399-L
2SK1399-L
< RESISTOR/CAPACITOR/FERRITE BEAD >
R101
R102
R103
R105
R106
1-216-809-11
1-216-295-00
1-216-864-11
1-216-833-11
1-216-833-11
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
100
0
0
10K
10K
5%
1/10W
5%
5%
1/10W
1/10W
R107
R108
R109
R110
R111
1-216-833-11
1-216-857-11
1-216-864-11
1-216-841-11
1-216-809-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
10K
1M
0
47K
100
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
R112
R113
R114
R115
R116
1-211-977-11
1-211-977-11
1-216-845-11
1-211-977-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22
22
100K
22
1K
0.5%
0.5%
5%
0.5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Note: EEPROM (IC103 and IC706) cannot exchange with single. When
EEPROM (IC103 and IC706) is damaged, exchange the entire
mounted board.
115
HCD-X1V
DMB12
Ref. No.
Part No.
Description
Remark
R207
R208
R209
1-216-826-11 METAL CHIP
1-216-839-11 METAL CHIP
1-216-839-11 METAL CHIP
2.7K
33K
33K
5%
5%
5%
1/10W
1/10W
1/10W
R210
R212
R213
R214
R215
1-216-841-11
1-216-833-11
1-218-867-11
1-216-835-11
1-216-834-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
10K
6.8K
15K
12K
5%
5%
0.5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R216
R219
R220
R221
R223
1-216-834-11
1-216-838-11
1-216-821-11
1-218-889-11
1-218-895-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
12K
27K
1K
56K
100K
5%
5%
5%
0.5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R224
R225
R226
R230
R231
1-216-833-11
1-218-895-11
1-218-889-11
1-218-893-11
1-218-875-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100K
56K
82K
15K
5%
0.5%
0.5%
0.5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R232
R233
R234
R246
R247
1-218-877-11
1-218-883-11
1-216-833-11
1-216-829-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
18K
33K
10K
4.7K
1K
0.5%
0.5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R701
R702
R703
R704
R705
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-829-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
0
0
0
0
4.7K
R708
R709
R712
R714
R718
1-216-821-11
1-216-821-11
1-216-809-11
1-216-864-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
R722
R723
R724
R725
R728
1-216-833-11
1-216-833-11
1-216-864-11
1-216-864-11
1-216-864-11
R730
R731
R734
R736
R738
5%
1/10W
1K
1K
100
0
4.7K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
10K
10K
0
0
0
5%
5%
1/10W
1/10W
1-218-840-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
510
0
0
0
0
0.5%
R740
R742
R743
R744
R745
1-216-864-11
1-216-841-11
1-216-821-11
1-216-829-11
1-216-821-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
47K
1K
4.7K
1K
R747
R748
R749
R750
R751
1-216-864-11
1-216-864-11
1-216-824-11
1-216-824-11
1-216-864-11
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
0
0
1.8K
1.8K
0
R752
R753
R754
R756
R759
1-216-864-11
1-216-864-11
1-216-864-11
1-216-833-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
SHORT CHIP
0
0
0
10K
0
116
5%
5%
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
Ref. No.
Part No.
Description
Remark
R760
R762
R763
R764
R765
1-216-809-11
1-216-864-11
1-216-864-11
1-216-829-11
1-216-864-11
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
SHORT CHIP
100
0
0
4.7K
0
5%
1/10W
5%
1/10W
R766
R767
R769
R770
R771
1-216-829-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
4.7K
0
0
0
0
5%
1/10W
R772
R773
R778
R779
R780
1-216-864-11
1-216-809-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
100
0
0
0
5%
1/10W
R781
R782
R783
R784
R785
1-216-833-11
1-216-833-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
10K
10K
0
0
0
5%
5%
1/10W
1/10W
R786
R787
R788
R789
R790
1-216-864-11
1-216-829-11
1-216-864-11
1-216-864-11
1-216-829-11
SHORT CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
0
4.7K
0
0
4.7K
5%
1/10W
5%
1/10W
R792
R793
R1101
R1102
R1110
1-216-829-11
1-216-864-11
1-218-855-11
1-218-827-11
1-216-826-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
0
2.2K
150
2.7K
5%
1/10W
0.5%
0.5%
5%
1/10W
1/10W
1/10W
R1114
R1115
R1120
R1121
R1122
1-216-801-11
1-216-864-11
1-469-118-21
1-469-118-21
1-469-118-21
METAL CHIP
22
5%
SHORT CHIP
0
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
R1123
R1124
R1125
R1129
R1133
1-469-118-21
1-469-118-21
1-469-118-21
1-216-845-11
1-216-864-11
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
METAL CHIP
100K
5%
SHORT CHIP
0
R1134
R1138
R1139
R1140
R1141
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
R1142
R1143
R1145
R1150
R1151
1-216-864-11
1-216-864-11
1-216-295-00
1-216-827-11
1-216-827-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
0
0
0
3.3K
3.3K
R1152
R1167
R1168
R1169
R1170
1-216-827-11
1-216-864-11
1-216-813-11
1-216-805-11
1-216-864-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
3.3K
0
220
47
0
R1173
R1176
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
0
0
1/10W
1/10W
5%
5%
1/10W
1/10W
5%
1/10W
5%
5%
1/10W
1/10W
HCD-X1V
DMB12
Ref. No.
Part No.
Description
Remark
Ref. No.
KEY
Part No.
Description
RB108
RB109
RB110
RB111
RB112
1-234-400-21
1-234-400-21
1-234-400-21
1-234-400-21
1-234-400-21
CONDUCTOR, NETWORK (2010X4)
CONDUCTOR, NETWORK (2010X4)
CONDUCTOR, NETWORK (2010X4)
CONDUCTOR, NETWORK (2010X4)
CONDUCTOR, NETWORK (2010X4)
RB113
RB114
RB115
RB116
RB117
1-234-400-21
1-234-400-21
1-234-400-21
1-234-371-21
1-234-371-21
CONDUCTOR, NETWORK (2010X4)
CONDUCTOR, NETWORK (2010X4)
CONDUCTOR, NETWORK (2010X4)
RES, NETWORK 47 (1005X4)
RES, NETWORK 47 (1005X4)
LED
Remark
R1177
R1178
R1179
1-216-809-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-809-11 METAL CHIP
100
1K
100
5%
5%
5%
1/10W
1/10W
1/10W
R1183
R1184
R1185
R1186
R1191
1-216-813-11
1-216-809-11
1-216-809-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
220
100
100
0
0
5%
5%
5%
1/10W
1/10W
1/10W
R1201
R1400
R1501
R1502
R1503
1-216-827-11
1-469-118-21
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
3.3K
5%
FERRITE, EMI (SMD) (1608)
SHORT CHIP
0
SHORT CHIP
0
SHORT CHIP
0
1/10W
R1705
R1706
R1710
R1715
R1750
1-216-821-11
1-216-821-11
1-216-829-11
1-216-864-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
1K
1K
4.7K
0
10K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R1751
R2504
R4501
R4502
R4510
1-216-833-11
1-216-829-11
1-216-864-11
1-216-864-11
1-216-809-11
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
10K
4.7K
0
0
100
5%
5%
1/10W
1/10W
5%
1/10W
R4511
R4512
R4513
R4514
R4515
1-216-809-11
1-400-244-11
1-216-864-11
1-216-809-11
1-216-809-11
METAL CHIP
100
5%
BEAD, FERRITE (CHIP) (1608)
SHORT CHIP
0
METAL CHIP
100
5%
METAL CHIP
100
5%
1/10W
R4516
R4518
R4520
R4527
R4610
1-216-809-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
100
0
0
0
0
1/10W
R4619
R4620
R4701
R4702
R4703
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
R4704
R4705
R4706
R4718
R4801
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
C806
C816
C817
C818
C819
1-162-962-11
1-162-960-11
1-162-960-11
1-162-960-11
1-162-960-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
220PF
220PF
220PF
220PF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
R4802
R4803
R4805
R5004
R5010
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
C820
C821
C822
C823
C824
1-162-960-11
1-162-960-11
1-162-960-11
1-162-960-11
1-162-960-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
220PF
220PF
220PF
220PF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
R5014
R5016
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
0 (US, CND)
0 (AEP, UK)
C825
C826
C827
C833
1-162-960-11
1-162-960-11
1-162-960-11
1-164-360-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
220PF
220PF
0.1uF
10%
10%
10%
50V
50V
50V
16V
< VIBRATOR >
X101
1-795-630-11 VIBRATOR, CRYSTAL (27MHz)
X701
1-795-244-11 VIBRATOR, CERAMIC (10MHz)
************************************************************
KEY BOARD
**********
< CONNECTOR >
5%
< COMPOSITION CIRCUIT BLOCK >
RB103
RB104
RB105
RB106
RB107
1-234-400-21
1-234-400-21
1-234-371-21
1-234-371-21
1-234-400-21
CONDUCTOR, NETWORK (2010X4)
CONDUCTOR, NETWORK (2010X4)
RES, NETWORK 47 (1005X4)
RES, NETWORK 47 (1005X4)
CONDUCTOR, NETWORK (2010X4)
CN804
CN805
1-785-330-11 PIN, CONNECTOR (LIGHT ANGLE) 4P
1-785-328-11 PIN, CONNECTOR (LIGHT ANGRE) 2P
< RESISTOR >
R852
R853
R862
1-216-825-11 METAL CHIP
1-216-825-11 METAL CHIP
1-216-825-11 METAL CHIP
1/10W
1/10W
2.2K
2.2K
2.2K
5%
5%
5%
1/10W
1/10W
1/10W
< SWITCH >
S801
1-786-033-41 SWITCH, TACTILE (N)
S802
1-786-033-41 SWITCH, TACTILE (VOLUME +)
S803
1-786-033-41 SWITCH, TACTILE (FUNCTION)
S804
1-786-033-41 SWITCH, TACTILE (x)
S805
1-786-033-41 SWITCH, TACTILE (VOLUME –)
************************************************************
LED BOARD
**********
< CAPACITOR >
< CONNECTOR >
CN807
1-784-860-51 CONNECTOR, FFC (LIF (NON-ZIF)) 8P
117
HCD-X1V
LED
Ref. No.
LF
MAIN
Part No.
Description
Remark
Ref. No.
Part No.
< LED >
D811
D812
D813
D814
D815
8-719-079-89
8-719-079-89
8-719-079-89
8-719-079-89
8-719-079-89
LED
LED
LED
LED
LED
Remark
< FUSE HOLDER >
SML-020MDT-T86 (DISC 1)
SML-020MDT-T86 (DISC 2)
SML-020MDT-T86 (DISC 3)
SML-020MDT-T86 (DISC 4)
SML-020MDT-T86 (DISC 5)
FH901
FH902
1-533-313-11 FUSE HOLDER
1-533-313-11 FUSE HOLDER
< LINE FILTER >
0 LF901
0 LF901
< IC >
IC802
Description
1-457-054-21 COIL, LINE FILTER (US, CND)
1-457-079-11 COIL, LINE FILTER (AEP, UK)
6-704-046-01 IC BU2099FV
< RESISTOR >
< RESISTOR >
R812
R813
R818
R819
R822
1-216-864-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-813-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
100
100
100
220
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R823
R824
R825
R826
R827
1-216-813-11
1-216-813-11
1-216-813-11
1-216-813-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
220
220
220
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R828
R829
R830
R831
R855
1-216-813-11
1-216-813-11
1-216-813-11
1-216-813-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
220
220
220
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R856
R857
R858
R859
R860
1-216-825-11
1-216-829-11
1-216-833-11
1-216-837-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
4.7K
10K
22K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
0 R901
1-219-759-11 METAL
1M
5%
0 R902
1-219-769-11 METAL
3.3M
5%
1/2W F
(AEP, UK)
1/2W F
(US, CND)
< THERMISTOR >
0 TH901
0 TH901
1-805-841-21 THERMISTOR, NTC 3.0 (US, CND)
1-805-842-21 THERMISTOR, NTC 6.0 (AEP, UK)
< VARISTOR >
0 VDR901 1-805-482-11 VARISTOR
************************************************************
A-1179-238-A MAIN BOARD, COMPLETE (US, CND)
A-1179-611-A MAIN BOARD, COMPLETE (AEP, UK)
*********************
< CAPACITOR/JUMPER RESISTOR >
C1
C2
C3
C6
C7
1-117-681-11
1-107-826-11
1-126-246-11
1-107-826-11
1-126-246-11
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
100uF
0.1uF
220uF
0.1uF
220uF
20%
10%
20%
10%
20%
16V
16V
4V
16V
4V
C9
C10
C11
C19
C23
1-162-916-11
1-162-913-11
1-107-826-11
1-117-370-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
12PF
8PF
0.1uF
10uF
0.1uF
5%
0.5PF
10%
10%
50V
50V
16V
10V
16V
C24
C25
C26
C28
C29
1-162-970-11
1-162-970-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
25V
25V
16V
16V
16V
C30
C32
C33
C34
C35
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C36
C39
C40
C42
C43
1-117-370-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10V
16V
16V
16V
16V
C45
C46
C49
C50
C52
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
< SWITCH >
S807
S808
S809
S810
S811
1-771-410-21
1-771-410-21
1-771-410-21
1-771-410-21
1-771-410-21
SWITCH, TACTILE (Z)
SWITCH, TACTILE (DISC 5)
SWITCH, TACTILE (DISC 4)
SWITCH, TACTILE (DISC 3)
SWITCH, TACTILE (DISC 2)
S812
1-771-410-21 SWITCH, TACTILE (DISC 1)
************************************************************
LF BOARD
*********
< CAPACITOR >
0 C901
0 C916
0 C961
1-165-529-11 MYLAR
1-113-912-11 CERAMIC
1-114-153-51 CERAMIC
0.22uF
10
0.0047uF 20%
680PF
10%
0 C962
1-114-153-51 CERAMIC
680PF
10%
0 C963
0 C964
1-112-875-51 CERAMIC
1-112-875-51 CERAMIC
330PF
330PF
10%
10%
275V
250V
125V
(AEP, UK)
125V
(AEP, UK)
125V
125V
< CONNECTOR >
CN901
CN905
118
1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P
1-564-321-00 PIN, CONNECTOR (3.96mm PITCH) 2P
HCD-X1V
MAIN
Ref. No.
Part No.
Description
C55
C57
C59
C61
C62
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
Remark
C63
C64
C66
C67
C70
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-117-370-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
10uF
10%
10%
10%
10%
16V
16V
16V
16V
10V
C71
C73
C74
C75
C76
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C77
C78
C79
C80
C81
1-107-826-11
1-107-826-11
1-107-826-11
1-117-681-11
1-126-246-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
0.1uF
0.1uF
0.1uF
100uF
220uF
10%
10%
10%
20%
20%
16V
16V
16V
16V
4V
C85
C200
C201
C202
C203
1-117-370-11
1-107-826-11
1-107-826-11
1-124-779-00
1-124-779-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
10uF
0.1uF
0.1uF
10uF
10uF
10%
10%
20%
20%
10V
16V
16V
16V
16V
C204
C205
C206
C207
C208
1-124-779-00
1-124-779-00
1-117-681-11
1-117-681-11
1-126-916-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT
10uF
10uF
100uF
100uF
1000uF
20%
20%
20%
20%
20%
16V
16V
16V
16V
6.3V
C209
C210
C211
C212
C213
1-126-916-11
1-126-916-11
1-107-826-11
1-124-779-00
1-107-826-11
ELECT
ELECT
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
1000uF
1000uF
0.1uF
10uF
0.1uF
20%
20%
10%
20%
10%
6.3V
6.3V
16V
16V
16V
C214
C215
C216
C217
C218
1-107-826-11
1-107-826-11
1-124-779-00
1-107-826-11
1-117-681-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
0.1uF
0.1uF
10uF
0.1uF
100uF
10%
10%
20%
10%
20%
16V
16V
16V
16V
16V
C219
C220
C224
C225
C226
1-117-681-11
1-117-681-11
1-107-826-11
1-117-681-11
1-162-927-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
100uF
100uF
0.1uF
100uF
100PF
20%
20%
10%
20%
5%
16V
16V
16V
16V
50V
C227
C228
C229
C230
C231
1-107-826-11
1-165-908-11
1-165-908-11
1-165-908-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
1uF
1uF
1uF
0.1uF
10%
10%
10%
10%
10%
16V
10V
10V
10V
16V
C232
C233
C234
C236
C302
1-117-681-11
1-126-193-11
1-124-779-00
1-117-681-11
1-107-823-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
100uF
1uF
10uF
100uF
0.47uF
20%
20%
20%
20%
10%
16V
50V
16V
16V
16V
C303
C304
C305
1-126-204-11 ELECT CHIP
1-107-826-11 CERAMIC CHIP
1-117-681-11 ELECT CHIP
47uF
0.1uF
100uF
20%
10%
20%
16V
16V
16V
Ref. No.
Part No.
Description
Remark
C306
C307
1-107-826-11 CERAMIC CHIP
1-162-960-11 CERAMIC CHIP
0.1uF
220PF
10%
10%
16V
50V
C308
C309
C312
C323
C331
1-162-960-11
1-126-395-11
1-126-395-11
1-107-826-11
1-162-960-11
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
22uF
22uF
0.1uF
220PF
10%
20%
20%
10%
10%
50V
16V
16V
16V
50V
C332
C333
C334
C341
C342
1-126-395-11
1-162-960-11
1-126-395-11
1-162-960-11
1-126-395-11
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
22uF
220PF
22uF
220PF
22uF
20%
10%
20%
10%
20%
16V
50V
16V
50V
16V
C343
C344
C354
C355
C356
1-162-960-11
1-126-395-11
1-126-193-11
1-117-681-11
1-107-826-11
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
220PF
22uF
1uF
100uF
0.1uF
10%
20%
20%
20%
10%
50V
16V
50V
16V
16V
C358
C359
C360
C364
C365
1-117-681-11
1-107-826-11
1-107-826-11
1-126-193-11
1-126-395-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
100uF
0.1uF
0.1uF
1uF
22uF
20%
10%
10%
20%
20%
16V
16V
16V
50V
16V
C366
C401
C402
C403
C404
1-107-826-11
1-126-204-11
1-162-927-11
1-117-681-11
1-107-826-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
47uF
100PF
100uF
0.1uF
10%
20%
5%
20%
10%
16V
16V
50V
16V
16V
C405
C406
C410
C411
C412
1-162-927-11
1-216-864-11
1-162-927-11
1-124-779-00
1-162-923-11
CERAMIC CHIP
SHORT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
100PF
0
100PF
10uF
47PF
5%
50V
5%
20%
5%
50V
16V
50V
C413
C419
C420
C421
C422
1-162-923-11
1-126-395-11
1-162-927-11
1-124-779-00
1-162-923-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
47PF
22uF
100PF
10uF
47PF
5%
20%
5%
20%
5%
50V
16V
50V
16V
50V
C423
C424
C471
C473
C501
1-162-923-11
1-126-395-11
1-117-370-11
1-117-370-11
1-107-826-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47PF
22uF
10uF
10uF
0.1uF
5%
20%
10%
50V
16V
10V
10V
16V
C502
C503
C504
C505
C506
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C507
C508
C509
C510
C511
1-107-826-11
1-107-826-11
1-165-908-11
1-107-826-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
1uF
0.1uF
0.001uF
10%
10%
10%
10%
10%
16V
16V
10V
16V
50V
C513
C515
C516
C517
C518
1-117-681-11
1-107-826-11
1-165-908-11
1-107-826-11
1-107-826-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
1uF
0.1uF
0.1uF
20%
10%
10%
10%
10%
16V
16V
10V
16V
16V
119
HCD-X1V
MAIN
Ref. No.
Part No.
Description
C519
C520
C521
C522
C523
1-107-826-11
1-127-715-11
1-162-970-11
1-127-715-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.22uF
0.01uF
0.22uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
25V
16V
16V
Remark
C524
C525
C526
C527
C528
1-126-204-11
1-107-826-11
1-117-681-11
1-104-656-11
1-117-681-11
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
ELECT
ELECT CHIP
47uF
0.1uF
100uF
2200uF
100uF
20%
10%
20%
20%
20%
16V
16V
16V
6.3V
16V
C529
C531
C532
C533
C534
1-107-823-11
1-107-826-11
1-107-826-11
1-107-826-11
1-117-681-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.47uF
0.1uF
0.1uF
0.1uF
100uF
10%
10%
10%
10%
20%
16V
16V
16V
16V
16V
C535
C536
C537
C538
C539
1-126-204-11
1-126-204-11
1-162-964-11
1-107-826-11
1-107-826-11
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
47uF
0.001uF
0.1uF
0.1uF
20%
20%
10%
10%
10%
16V
16V
50V
16V
16V
C540
C541
C542
C543
C544
1-117-681-11
1-107-826-11
1-117-681-11
1-100-566-91
1-128-992-21
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
100uF
0.1uF
100uF
0.1uF
47uF
20%
10%
20%
10%
20%
16V
16V
16V
25V
25V
C545
C546
C547
C548
C549
1-107-826-11
1-117-681-11
1-107-826-11
1-126-205-11
1-126-205-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
0.1uF
100uF
0.1uF
47uF
47uF
10%
20%
10%
20%
20%
16V
16V
16V
6.3V
6.3V
C550
C551
C601
C602
C624
1-107-826-11
1-162-923-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
47PF
0.1uF
0.1uF
0.1uF
10%
5%
10%
10%
10%
16V
50V
16V
16V
16V
C625
C626
C627
C702
C704
1-107-826-11
1-162-970-11
1-162-970-11
1-107-826-11
1-216-864-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
SHORT CHIP
0.1uF
0.01uF
0.01uF
0.1uF
0
10%
10%
10%
10%
16V
25V
25V
16V
C705
C706
C707
C708
C709
1-126-204-11
1-126-204-11
1-107-826-11
1-107-826-11
1-124-779-00
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
47uF
47uF
0.1uF
0.1uF
10uF
20%
20%
10%
10%
20%
16V
16V
16V
16V
16V
C710
C711
C712
C713
C714
1-110-563-11
1-107-826-11
1-216-864-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
SHORT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.068uF
0.1uF
0
0.1uF
0.1uF
10%
10%
16V
16V
10%
10%
16V
16V
C715
C716
C717
C718
C719
1-162-964-11
1-162-970-11
1-124-779-00
1-126-204-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
0.001uF
0.01uF
10uF
47uF
0.1uF
10%
10%
20%
20%
10%
50V
25V
16V
16V
16V
C720
C721
C722
1-117-681-11 ELECT CHIP
1-162-970-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
100uF
0.01uF
0.1uF
20%
10%
10%
16V
25V
16V
Ref. No.
Part No.
Description
Remark
C723
C724
1-107-826-11 CERAMIC CHIP
1-162-917-11 CERAMIC CHIP
0.1uF
15PF
10%
5%
16V
50V
C725
C727
C728
C729
C730
1-162-916-11
1-107-826-11
1-117-681-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
12PF
0.1uF
100uF
0.1uF
0.1uF
5%
10%
20%
10%
10%
50V
16V
16V
16V
16V
C731
C732
C733
C737
C738
1-107-826-11
1-117-681-11
1-127-715-11
1-107-826-11
1-117-370-11
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
0.22uF
0.1uF
10uF
10%
20%
10%
10%
16V
16V
16V
16V
10V
C751
C752
C771
1-162-970-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
1-162-970-11 CERAMIC CHIP
0.01uF
0.1uF
0.01uF
10%
10%
10%
25V
16V
25V
< CONNECTOR >
CN201
CN303
CN303
* CN401
CN501
1-784-863-51
1-568-828-11
1-568-830-11
1-564-720-11
1-784-871-51
CONNECTOR, FFC (LIF (NON-ZIF)) 11P
CONNECTOR, FFC 9P (US, CND)
CONNECTOR, FFC 11P (AEP, UK)
PIN, CONNECTOR (SMALL TYPE) 4P
CONNECTOR, FFC (LIF (NON-ZIF)) 19P
CN504
CN505
* CN506
CN507
CN621
1-784-863-51
1-564-721-11
1-564-729-11
1-784-871-51
1-784-835-51
CONNECTOR, FFC (LIF (NON-ZIF)) 11P
PIN, CONNECTOR (SMALL TYPE) 5P
PIN, CONNECTOR (SMALL TYPE) 13P
CONNECTOR, FFC (LIF (NON-ZIF)) 19P
CONNECTOR, FFC (LIF (NON-ZIF)) 27P
CN701
1-784-863-51 CONNECTOR, FFC (LIF (NON-ZIF)) 11P
< DIODE >
120
D501
D502
D503
D504
D701
6-501-193-01
6-501-193-01
6-501-181-01
6-501-193-01
6-501-193-01
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355WTE-17
1SS355WTE-17
UDZW-TE17-20B
1SS355WTE-17
1SS355WTE-17
D702
6-501-193-01 DIODE 1SS355WTE-17
< JUMPER RESISTOR/FERRITE BEAD >
FB1
FB2
FB301
FB501
FB502
1-216-295-00
1-216-295-00
1-216-295-00
1-469-324-21
1-469-324-21
SHORT CHIP
0
SHORT CHIP
0
SHORT CHIP
0
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
FB503
FB505
FB506
FB507
FB508
1-469-324-21
1-469-324-21
1-469-324-21
1-469-324-21
1-469-324-21
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
FB509
FB510
FB701
FB702
FB703
1-469-324-21
1-469-324-21
1-216-295-00
1-500-283-11
1-216-864-11
FERRITE, EMI (SMD) (2012)
FERRITE, EMI (SMD) (2012)
SHORT CHIP
0
INDUCTOR, FERRITE BEAD
SHORT CHIP
0
FB704
FB751
FB752
1-216-864-11 SHORT CHIP
0
1-500-283-11 INDUCTOR, FERRITE BEAD
1-216-295-00 SHORT CHIP
0
HCD-X1V
MAIN
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
< FILTER >
FL501
FL502
FL503
Description
Remark
< TRANSISTOR >
1-233-893-21 FILTER, CHIP EMI
1-234-177-21 FILTER, CHIP EMI
1-234-177-21 FILTER, CHIP EMI
< IC >
Q301
Q302
Q304
Q305
Q395
8-729-027-24
8-729-027-24
8-729-027-59
8-729-027-52
8-729-027-52
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA114TKA-T146
DTA114TKA-T146
DTC144EKA-T146
DTC124EKA-T146
DTC124EKA-T146
IC1
IC2
IC200
IC201
IC202
6-705-308-01
6-709-759-01
8-759-696-10
8-759-696-10
8-759-696-10
IC
IC
IC
IC
IC
SI-3010KM-TL
ADSST-AVR-1115
NJM2235V (TE2)
NJM2235V (TE2)
NJM2235V (TE2)
Q396
Q397
Q501
Q502
Q503
8-729-027-52
8-729-027-52
8-729-027-43
8-729-600-22
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC124EKA-T146
DTC124EKA-T146
DTC114EKA-T146
2SA1235-F
2SC1623-L5L6
IC203
IC300
IC350
IC351
IC360
6-707-489-01
6-703-550-01
8-759-385-76
8-759-385-76
8-759-100-96
IC
IC
IC
IC
IC
BH7868FS-E2
TA7809LS
MC14052 BDR2
MC14052 BDR2
uPC4558G2
Q504
Q701
6-550-718-01 TRANSISTOR
8-729-027-24 FET
RSR025N03TL
DTA114TKA-T146
IC401
IC501
IC502
IC503
IC504
8-759-100-96
6-806-495-01
6-702-302-01
6-708-922-01
6-709-034-01
IC
IC
IC
IC
IC
uPC4558G2
M30626MJP-A05FPU0
TK11133CSCL-G
PST3635NR
NJM2887DL3 (TE2)
IC505
IC506
IC507
IC621
IC622
6-705-308-01
6-705-308-01
6-705-308-01
6-707-095-01
6-707-095-01
IC
IC
IC
IC
IC
SI-3010KM-TL
SI-3010KM-TL
SI-3010KM-TL
BH2210FV-E2
BH2210FV-E2
IC701
IC702
IC703
IC704
IC705
6-709-033-01
6-805-692-01
6-705-308-01
6-701-990-01
8-759-548-99
IC
IC
IC
IC
IC
WM8782SEDS/R
LC890561W
SI-3010KM-TL
SN74LVC257APWR
SN74LV08APWR
IC706
IC771
6-708-380-01 IC SN74LVC1G79DCKR
6-703-046-01 IC SN74LVC1G08DCKR
< JACK/TERMINAL >
J200
J201
J301
1-815-361-11 JACK, PIN 3P (COMPONENT VIDEO OUT)
1-780-211-11 TERMINAL BOARD (S TERMINAL+1P)
(MONITOR OUT)
1-780-211-11 TERMINAL BOARD (S TERMINAL+1P)
(VIDEO IN VIDEO1)
1-780-211-11 TERMINAL BOARD (S TERMINAL+1P)
(VIDEO IN VIDEO2)
1-816-549-11 JACK, PIN 6P (AUDIO IN VIDEO1, VIDEO2, TV)
J401
1-566-891-21 JACK (A.CAL MIC ECM-AC1)
J202
J203
< RESISTOR/FERRITE BEAD >
R2
R3
R4
R13
R14
1-216-833-11
1-216-864-11
1-216-833-11
1-216-864-11
1-218-854-11
METAL CHIP
SHORT CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
10K
0
10K
0
2K
5%
1/10W
5%
1/10W
0.5%
1/10W
R15
R16
R17
R18
R20
1-218-871-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
10K
0
0
0
0
0.5%
1/10W
R21
R23
R24
R25
R26
1-216-833-11
1-216-817-11
1-216-821-11
1-216-864-11
1-216-801-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
10K
470
1K
0
22
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R27
R28
R29
R30
R32
1-216-801-11
1-216-801-11
1-216-801-11
1-216-801-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22
22
22
22
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R35
R36
R38
R41
R43
1-216-857-11
1-216-797-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1M
10
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R45
R47
R48
R49
R50
1-216-833-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
10K
0
0
0
0
5%
1/10W
R51
R52
R53
R54
R55
1-216-864-11
1-216-864-11
1-216-805-11
1-216-801-11
1-216-864-11
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
0
0
47
22
0
5%
5%
1/10W
1/10W
R56
R57
R58
R59
R60
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-801-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
0
0
0
0
22
5%
1/10W
R64
R65
1-216-801-11 METAL CHIP
1-216-801-11 METAL CHIP
22
22
5%
5%
1/10W
1/10W
< COIL/JUMPER RESISTOR >
L200
L201
L202
L203
L300
1-469-525-11
1-469-525-11
1-469-525-11
1-469-525-11
1-469-525-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
10uH
10uH
10uH
10uH
L701
L702
L703
L704
L705
1-414-754-11
1-414-754-11
1-414-754-11
1-414-754-11
1-216-295-00
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
SHORT CHIP
10uH
10uH
10uH
10uH
0
121
HCD-X1V
MAIN
Ref. No.
Part No.
Description
Remark
R66
R67
R200
1-216-801-11 METAL CHIP
1-216-801-11 METAL CHIP
1-218-285-11 METAL CHIP
22
22
75
5%
5%
5%
1/10W
1/10W
1/10W
R201
R202
R203
R204
R205
1-218-285-11
1-218-285-11
1-218-285-11
1-218-285-11
1-218-285-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
75
75
75
75
75
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R206
R207
R208
R209
R210
1-218-285-11
1-218-285-11
1-218-285-11
1-218-285-11
1-218-285-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
75
75
75
75
75
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R211
R214
R216
R217
R218
1-218-285-11
1-216-833-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
75
10K
0
0
0
5%
5%
1/10W
1/10W
R220
R221
R223
R224
R226
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
R227
R228
R229
R230
R300
1-216-821-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-789-11
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
1K
0
0
0
2.2
5%
5%
1/10W
R301
R302
R303
R304
R305
1-216-833-11
1-216-864-11
1-216-813-11
1-216-813-11
1-216-849-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
0
220
220
220K
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
R306
R307
R308
R309
R310
1-216-849-11
1-216-841-11
1-216-841-11
1-216-841-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
220K
47K
47K
47K
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R311
R315
R316
R317
R325
1-216-864-11
1-216-841-11
1-216-833-11
1-216-833-11
1-216-833-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0 (US, CND)
47K
5%
10K
5%
10K
5%
10K
5%
1/10W
1/10W
1/10W
1/10W
R326
R327
R331
R332
R335
1-216-833-11
1-216-833-11
1-216-813-11
1-216-849-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
220
220K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R336
R337
R338
R339
R340
1-216-841-11
1-216-813-11
1-216-849-11
1-216-841-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
220
220K
47K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R341
R342
R345
R346
R347
1-216-813-11
1-216-849-11
1-216-841-11
1-216-841-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
220K
47K
47K
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
122
1/10W
Ref. No.
Part No.
Description
Remark
R348
R349
R350
R352
R354
1-216-849-11
1-216-841-11
1-216-841-11
1-216-845-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220K
47K
47K
100K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R355
R356
R358
R359
R360
1-216-833-11
1-216-833-11
1-216-833-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R362
R364
R365
R398
R401
1-216-845-11
1-216-829-11
1-216-833-11
1-216-833-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
4.7K
10K
10K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R402
R403
R403
R404
R405
1-216-829-11
1-216-864-11
1-414-760-21
1-216-822-11
1-216-849-11
METAL CHIP
4.7K
5%
1/10W
SHORT CHIP
0 (US, CND)
FERRITE, EMI (SMD) (1608) (AEP, UK)
METAL CHIP
1.2K
5%
1/10W
METAL CHIP
220K
5%
1/10W
R406
R407
R408
R409
R410
1-216-849-11
1-216-813-11
1-216-813-11
1-414-760-21
1-216-845-11
METAL CHIP
220K
METAL CHIP
220
METAL CHIP
220
FERRITE, EMI (SMD) (1608)
METAL CHIP
100K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R411
R412
R413
R414
R415
1-216-817-11
1-216-837-11
1-216-817-11
1-216-838-11
1-414-760-21
METAL CHIP
470
METAL CHIP
22K
METAL CHIP
470
METAL CHIP
27K
FERRITE, EMI (SMD) (1608)
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R416
R416
R417
R417
R418
1-216-864-11
1-414-760-21
1-216-864-11
1-414-760-21
1-216-864-11
SHORT CHIP
0 (AEP, UK)
FERRITE, EMI (SMD) (1608) (US, CND)
SHORT CHIP
0 (AEP, UK)
FERRITE, EMI (SMD) (1608) (US, CND)
SHORT CHIP
0 (AEP, UK)
R418
R419
R419
R420
R421
1-414-760-21
1-216-864-11
1-414-760-21
1-216-845-11
1-216-817-11
FERRITE, EMI (SMD) (1608) (US, CND)
SHORT CHIP
0 (AEP, UK)
FERRITE, EMI (SMD) (1608) (US, CND)
METAL CHIP
100K
5%
1/10W
METAL CHIP
470
5%
1/10W
R422
R423
R424
R425
R430
1-216-837-11
1-216-817-11
1-216-838-11
1-216-864-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
R431
R432
R433
R446
R446
1-216-841-11
1-216-841-11
1-216-841-11
1-216-864-11
1-414-760-21
METAL CHIP
47K
5%
1/10W
METAL CHIP
47K
5%
1/10W
METAL CHIP
47K
5%
1/10W
SHORT CHIP
0 (AEP, UK)
FERRITE, EMI (SMD) (1608) (US, CND)
R447
R447
R448
R448
R449
1-216-864-11
1-414-760-21
1-216-864-11
1-414-760-21
1-216-864-11
SHORT CHIP
0 (AEP, UK)
FERRITE, EMI (SMD) (1608) (US, CND)
SHORT CHIP
0 (AEP, UK)
FERRITE, EMI (SMD) (1608) (US, CND)
SHORT CHIP
0 (AEP, UK)
R449
R470
1-414-760-21 FERRITE, EMI (SMD) (1608) (US, CND)
1-216-825-11 METAL CHIP
2.2K
5%
1/10W
22K
470
27K
0
47K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
HCD-X1V
MAIN
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
R471
R472
R473
1-216-822-11 METAL CHIP
1-216-827-11 METAL CHIP
1-216-825-11 METAL CHIP
1.2K
3.3K
2.2K
5%
5%
5%
1/10W
1/10W
1/10W
R573
R574
R575
1-216-845-11 METAL CHIP
1-216-864-11 SHORT CHIP
1-216-821-11 METAL CHIP
100K
0
1K
5%
1/10W
5%
1/10W
R474
R501
R502
R503
R504
1-216-827-11
1-216-821-11
1-216-833-11
1-216-833-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
1K
10K
10K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
(US, CND)
R576
R577
R579
R580
R582
1-216-821-11
1-216-841-11
1-216-833-11
1-216-829-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
47K
10K
4.7K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R505
R506
1-216-821-11 METAL CHIP
1-216-829-11 METAL CHIP
1K
4.7K
5%
5%
R506
1-216-837-11 METAL CHIP
22K
5%
R583
R584
R585
R586
R587
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R508
R509
1-216-821-11 METAL CHIP
1-216-809-11 METAL CHIP
1K
100
5%
5%
1/10W
1/10W
(AEP, UK)
1/10W
(US, CND)
1/10W
1/10W
R510
R511
R512
R513
R514
1-216-833-11
1-216-809-11
1-216-833-11
1-216-809-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100
10K
100
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R588
R589
R591
R592
R593
1-216-809-11
1-216-809-11
1-216-809-11
1-216-825-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
2.2K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
10K
1K
10K
100
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
10K
0
10K
0
22
5%
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
1/10W
1-216-833-11
1-216-821-11
1-216-833-11
1-216-809-11
1-216-833-11
1-216-833-11
1-216-864-11
1-216-833-11
1-216-864-11
1-216-801-11
5%
R517
R518
R519
R521
R522
R594
R596
R597
R600
R601
5%
1/10W
R523
R524
R525
R526
R528
1-216-833-11
1-216-833-11
1-216-833-11
1-216-821-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
10K
10K
10K
1K
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R602
R603
R604
R605
R606
1-216-801-11
1-216-801-11
1-216-801-11
1-216-801-11
1-216-805-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22
22
22
22
47
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R529
R530
R532
R533
R534
1-216-821-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100
100
100
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R608
R609
R618
R619
R621
1-216-864-11
1-216-833-11
1-216-809-11
1-216-809-11
1-216-809-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
10K
100
100
100
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
100
0
0
10K
10K
5%
1/10W
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
10K
100
0
0
100
1/10W
1/10W
1-216-809-11
1-216-864-11
1-216-864-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-809-11
1-216-864-11
1-216-864-11
1-216-809-11
5%
5%
R535
R536
R537
R539
R540
R622
R623
R624
R625
R628
5%
1/10W
5%
5%
1/10W
1/10W
R542
R544
R545
R547
R548
1-216-834-11
1-216-821-11
1-216-833-11
1-216-821-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
12K
1K
10K
1K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R629
R630
R631
R632
R633
1-216-813-11
1-216-813-11
1-216-813-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
220
220
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R549
R550
R552
R555
R556
1-216-829-11
1-216-833-11
1-216-829-11
1-216-833-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
10K
4.7K
10K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R634
R635
R636
R637
R638
1-216-813-11
1-216-833-11
1-216-841-11
1-216-837-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
10K
47K
22K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
10K
100K
47K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
0
3.3K
10K
10K
1/10W
1-216-841-11
1-216-833-11
1-216-845-11
1-216-841-11
1-216-833-11
1-216-821-11
1-216-864-11
1-216-827-11
1-216-833-11
1-216-833-11
5%
R557
R558
R561
R562
R563
R639
R640
R642
R643
R645
5%
5%
5%
1/10W
1/10W
1/10W
1K
300K
5%
0.5%
1/10W
1/10W
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330
0
1K
1K
10K
1/10W
1-216-821-11 METAL CHIP
1-218-751-11 METAL CHIP
1-216-815-11
1-216-864-11
1-216-821-11
1-216-821-11
1-216-833-11
5%
R570
R572
R701
R702
R705
R706
R707
5%
5%
5%
1/10W
1/10W
1/10W
123
HCD-X1V
MAIN
Ref. No.
MODE MOTOR
Part No.
POWER
Description
Remark
R708
R709
R710
R711
R712
1-216-827-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R713
R716
R718
R719
R721
1-216-864-11
1-216-813-11
1-216-809-11
1-216-809-11
1-216-813-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
220
100
100
220
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R722
R723
R724
R725
R726
1-216-809-11
1-216-809-11
1-216-809-11
1-216-813-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
220
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R727
R728
R729
R730
R731
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R732
R733
R734
R735
R736
1-216-821-11
1-216-857-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1M
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R737
R738
R739
R740
R741
1-216-864-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
100
100
100
100
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R742
R743
R744
R745
R746
1-216-821-11
1-216-809-11
1-216-833-11
1-216-835-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100
10K
15K
100
5%
5%
5%
5%
5%
R747
R748
R749
R750
R751
1-216-809-11
1-216-849-11
1-216-809-11
1-216-813-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
220K
100
220
100
R752
R753
R754
R755
R756
1-216-809-11
1-216-809-11
1-216-809-11
1-216-811-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
R757
R758
R759
R760
R761
1-216-809-11
1-216-833-11
1-216-809-11
1-216-809-11
1-216-809-11
R762
R763
R764
Ref. No.
Part No.
Description
Remark
RB603
RB621
RB622
1-233-576-11 RES, CHIP NETWORK 100 (3216)
1-233-576-11 RES, CHIP NETWORK 100 (3216)
1-233-576-11 RES, CHIP NETWORK 100 (3216)
RB623
RB624
RB625
RB626
RB627
1-233-411-11
1-233-411-11
1-233-411-11
1-233-411-11
1-236-908-11
RB628
RB629
RB630
1-236-908-11 RES, CHIP NETWORK 10K (3216)
1-236-908-11 RES, CHIP NETWORK 10K (3216)
1-236-908-11 RES, CHIP NETWORK 10K (3216)
RES, CHIP NETWORK 220 (3216)
RES, CHIP NETWORK 220 (3216)
RES, CHIP NETWORK 220 (3216)
RES, CHIP NETWORK 220 (3216)
RES, CHIP NETWORK 10K (3216)
< VIBRATOR >
X1
1-795-807-11 VIBRATOR, CRYSTAL (25MHz)
X501
1-795-121-21 VIBRATOR, CERAMIC (5MHz)
X701
1-795-843-11 VIBRATOR, CRYSTAL (12.288MHz)
************************************************************
1-686-724-13 MODE MOTOR BOARD
******************
************************************************************
A-1179-243-A POWER BOARD, COMPLETE (US, CND)
A-1179-614-A POWER BOARD, COMPLETE (AEP, UK)
***********************
7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
0 C902
0 C903
1-165-529-11 MYLAR
1-112-330-11 ELECT (BLOCK)
0.22uF
1000uF
10
20%
1/10W
1/10W
1/10W
1/10W
1/10W
0 C903
1-112-332-11 ELECT (BLOCK)
330uF
20%
C904
0 C905
1-100-566-91 CERAMIC CHIP
1-112-334-11 FILM
0.1uF
0.01uF
10%
5%
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
0 C905
1-112-335-11 FILM
0.0033uF 5%
0 C906
1-117-815-11 FILM
1000PF
3%
0 C906
1-117-828-11 FILM
3300PF
3%
100
100
100
150
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
0 C907
1-162-964-11 CERAMIC CHIP
0.001uF
10%
0 C907
1-162-965-11 CERAMIC CHIP
0.0015uF 10%
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
10K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
0 C908
0 C909
0 C910
0 C911
C912
1-107-909-11
1-162-960-11
1-107-909-11
1-162-968-11
1-100-566-91
47uF
220PF
47uF
0.0047uF
0.1uF
20%
10%
20%
10%
10%
0 C913
1-112-873-51 CERAMIC
100PF
10%
1-216-813-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-864-11 SHORT CHIP
220
100
0
5%
5%
1/10W
1/10W
0 C913
1-112-877-51 CERAMIC
0.001uF
20%
0 C914
0 C915
C917
1-107-902-11 ELECT
1-107-902-11 ELECT
1-100-566-91 CERAMIC CHIP
1uF
1uF
0.1uF
20%
20%
10%
0 C918
1-113-925-11 CERAMIC
0.01uF
20%
< COMPOSITION CIRCUIT BLOCK >
RB601
RB602
124
< CAPACITOR >
1-233-576-11 RES, CHIP NETWORK 100 (3216)
1-233-576-11 RES, CHIP NETWORK 100 (3216)
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
275V
200V
(US, CND)
400V
(AEP, UK)
25V
400V
(US, CND)
400V
(AEP, UK)
1.5KV
(AEP, UK)
1.5KV
(US, CND)
50V
(AEP, UK)
50V
(US, CND)
50V
50V
50V
50V
25V
125V
(AEP, UK)
125V
(US, CND)
50V
50V
25V
250V
HCD-X1V
POWER
Ref. No.
Part No.
Description
C919
0 C920
C921
0 C922
1-100-566-91
1-113-925-11
1-100-566-91
1-128-560-11
CERAMIC CHIP
CERAMIC
CERAMIC CHIP
ELECT
0.1uF
0.01uF
0.1uF
22uF
10%
20%
10%
20%
0 C923
0 C924
0 C925
0 C928
1-162-968-11
1-126-961-11
1-107-974-11
1-112-875-51
CERAMIC CHIP
ELECT
CERAMIC
CERAMIC
0.0047uF
2.2uF
47PF
330PF
10%
20%
5%
10%
0 C928
1-112-876-51 CERAMIC
470PF
10%
0 C929
C932
C933
C934
C935
1-115-339-11
1-100-924-21
1-100-924-21
1-107-898-11
1-165-319-11
CERAMIC CHIP
ELECT
ELECT
ELECT
CERAMIC CHIP
0.1uF
2200uF
2200uF
2200uF
0.1uF
10%
20%
20%
20%
C936
C937
0 C938
1-165-319-11 CERAMIC CHIP
1-100-756-91 CERAMIC CHIP
1-112-875-51 CERAMIC
0.1uF
0.047uF
330PF
10%
0 C938
1-112-876-51 CERAMIC
470PF
10%
C939
1-136-165-00 FILM
0.1uF
5%
C940
C941
C944
C946
C947
1-128-951-21
1-128-954-11
1-128-951-21
1-128-950-21
1-100-566-91
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
2200uF
1000uF
2200uF
1000uF
0.1uF
20%
20%
20%
20%
10%
C948
C952
0 C954
1-100-566-91 CERAMIC CHIP
1-100-756-91 CERAMIC CHIP
1-112-334-11 FILM
0.1uF
0.047uF
0.01uF
10%
0 C954
1-112-335-11 FILM
0.0033uF 5%
0 C955
1-162-968-11 CERAMIC CHIP
0.0047uF 10%
C958
C960
C966
C967
C968
1-100-566-91
1-100-566-91
1-100-566-91
1-100-566-91
1-100-566-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C976
C977
C978
C979
C980
1-126-933-11
1-100-566-91
1-100-566-91
1-100-566-91
1-100-566-91
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
0.1uF
0.1uF
0.1uF
20%
10%
10%
10%
10%
16V
25V
25V
25V
25V
C981
C982
1-100-566-91 CERAMIC CHIP
1-100-566-91 CERAMIC CHIP
0.1uF
0.1uF
10%
10%
25V
25V
5%
Remark
Ref. No.
Part No.
25V
250V
25V
100V
0 D907
6-501-193-01 DIODE 1SS355WTE-17
0 D908
0 D909
0 D913
0 D914
0 D915
6-501-193-01
6-501-193-01
6-500-241-01
6-501-193-01
6-501-174-01
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355WTE-17
1SS355WTE-17
SARS03
1SS355WTE-17
UDZW-TE17-10B
0 D922
0 D923
0 D924
0 D925
D931
8-719-063-74
6-501-167-01
6-501-183-01
6-501-167-01
6-501-413-01
DIODE
DIODE
DIODE
DIODE
DIODE
D1NL20U-TR2
UDZW-TE17-5.1B
UDZW-TE17-24B
UDZW-TE17-5.1B
FCU20UC20
0 D935
D941
D942
D943
D944
6-501-193-01
6-500-288-11
8-719-080-53
8-719-080-53
6-500-288-11
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355WTE-17
EK19LF-F7
RK36LF-B3
RK36LF-B3
EK19LF-F7
50V
50V
2KV
125V
(US, CND)
125V
(AEP, UK)
50V
35V
35V
35V
50V
50V
50V
125V
(US, CND)
125V
(AEP, UK)
50V
16V
25V
16V
16V
25V
25V
50V
400V
(US, CND)
400V
(AEP, UK)
50V
Description
Remark
< IC >
IC507
0 IC901
0 IC901
0 IC921
IC931
IC951
6-705-308-01
6-707-741-01
6-707-742-01
6-707-740-01
8-759-648-34
IC
IC
IC
IC
IC
SI-3010KM-TL
STR-F6138-LF1352 (US, CND)
STR-F6168-LF1352 (AEP, UK)
STR-V153
TA76431AS (TPE6)
6-707-743-01 IC TA76L431S (TPE6, Q)
< COIL/FILTER >
L931
L932
L934
L935
L936
1-457-058-11
1-416-668-31
1-416-668-31
1-416-668-31
1-424-122-11
CHOKE, COIL
CHOKE, COIL
CHOKE, COIL
CHOKE, COIL
FILTER, NOISE
L937
L948
1-424-122-11 FILTER, NOISE
1-416-668-31 CHOKE, COIL
10.8uH
10uH
10uH
10uH
10uH
< PHOTO COUPLER >
PC901
PC902
PC903
6-600-438-01 PHOTO COUPLER TLP421F (D4-GR)
6-600-438-01 PHOTO COUPLER TLP421F (D4-GR)
6-600-438-01 PHOTO COUPLER TLP421F (D4-GR)
< TRANSISTOR >
0 Q904
0 Q921
Q943
8-729-027-23 TRANSISTOR
8-729-142-51 TRANSISTOR
8-729-027-46 TRANSISTOR
DTA114EKA-T146
2SD1616A-TP-LK
DTC114YKA-T146
< RESISTOR >
0 R903
1-215-927-00 METAL OXIDE
47K
5%
0 R903
1-216-488-11 METAL OXIDE
18K
5%
0 R905
0 R906
0 R908
1-216-797-11 METAL CHIP
1-216-827-11 METAL CHIP
1-216-827-11 METAL CHIP
10
3.3K
3.3K
5%
5%
5%
3W F
(AEP, UK)
3W F
(US, CND)
1/10W
1/10W
1/10W
0 R909
0 R910
0 R911
0 R912
1-216-845-11
1-216-825-11
1-216-813-11
1-216-361-61
100K
2.2K
220
0.22
5%
5%
5%
5%
1/10W
1/10W
1/10W
2W F
< CONNECTOR >
* CN902
* CN903
CN904
CN906
1-770-470-21
1-564-241-11
1-815-954-21
1-564-321-00
PIN, CONNECTOR (PC BOARD) 6P
PIN, CONNECTOR (3.96mm PITCH) 4P
PIN, CONNECTOR (PC BOARD) 13P
PIN, CONNECTOR (3.96mm PITCH) 2P
< DIODE >
0 D901
0 D903
0 D905
0 D906
8-719-082-57
6-501-424-01
8-719-063-74
6-501-193-01
DIODE
DIODE
DIODE
DIODE
D5SBA60F01
STO2D-140
D1NL20U-TR2
1SS355WTE-17
METAL CHIP
METAL CHIP
METAL CHIP
METAL OXIDE
125
HCD-X1V
POWER
Ref. No.
POWER-SW
Part No.
RELAY
Description
Remark
0 R912
1-216-363-00 METAL OXIDE
0.33
5%
0 R914
1-243-665-11 METAL
0.05
5%
0 R914
1-243-666-11 METAL
0.1
5%
1-216-821-11 METAL CHIP
1-216-789-11 METAL CHIP
1-216-789-11 METAL CHIP
1K
2.2
2.2
0 R919
0 R922
0 R923
0 R925
0 R926
1-216-836-11
1-216-793-11
1-216-829-11
1-216-797-11
1-216-855-11
0 R927
Ref. No.
Part No.
Description
Remark
A-4731-113-A RELAY BOARD, COMPLETE
**********************
(Including ST ENCODER BOARD)
(US, CND)
2W F
(AEP, UK)
< CAPACITOR >
5%
5%
5%
5W F
(US, CND)
5W F
(AEP, UK)
1/10W
1/10W
1/10W
C711
C751
C752
C753
C754
1-126-795-11
1-164-159-21
1-164-159-21
1-164-159-21
1-164-159-21
ELECT
CERAMIC
CERAMIC
CERAMIC
CERAMIC
10uF
0.1uF
0.1uF
0.1uF
0.1uF
18K
4.7
4.7K
10
680K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C755
C756
C758
C761
C762
1-164-159-21
1-164-159-21
1-164-159-21
1-162-306-11
1-164-159-21
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.1uF
0.1uF
0.1uF
0.01uF
0.1uF
1-216-348-00 METAL OXIDE
0.82
5%
0 R927
1-216-349-00 METAL OXIDE
1
0 R928
0 R929
R931
1-216-821-11 METAL CHIP
1-249-478-11 CARBON
1-218-863-11 METAL CHIP
1K
2.2
4.7K
1W F
(US, CND)
5%
1W F
(AEP, UK)
5%
1/10W
5%
1/2W
0.5% 1/10W
C763
C764
C765
C766
C767
1-164-159-21
1-164-159-21
1-164-159-21
1-164-159-21
1-164-159-21
CERAMIC
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
50V
50V
50V
50V
50V
1-218-883-11
1-216-829-11
1-216-821-11
1-216-821-11
1-216-853-11
33K
4.7K
1K
1K
470K
0.5%
5%
5%
5%
5%
C768
C769
C771
C781
1-164-159-21
1-164-159-21
1-162-306-11
1-162-306-11
CERAMIC
CERAMIC
CERAMIC
CERAMIC
0.1uF
0.1uF
0.01uF
0.01uF
50V
50V
16V
16V
0.5%
5%
R915
R916
R918
R932
R933
R934
R935
R936
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1/10W
1/10W
1/10W
1/10W
1/10W
R939
0 R945
1-218-859-11 METAL CHIP
1-215-901-61 METAL OXIDE
3.3K
33K
0 R945
1-215-903-61 METAL OXIDE
68K
R946
R949
1-218-871-11 METAL CHIP
1-216-821-11 METAL CHIP
10K
1K
1/10W
2W F
(US, CND)
5%
2W F
(AEP, UK)
0.5% 1/10W
5%
1/10W
R951
R952
R953
R954
R955
1-218-831-11
1-218-855-11
1-218-861-11
1-218-879-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
2.2K
3.9K
22K
470
0.5%
0.5%
0.5%
0.5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R956
R957
R958
R965
R967
1-216-821-11
1-218-891-11
1-218-855-11
1-218-859-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
68K
2.2K
3.3K
1K
5%
0.5%
0.5%
0.5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1K
5%
1/10W
0 R969
1-216-821-11 METAL CHIP
< TRANSFORMER >
0 T901
1-443-649-11 TRANSFORMER, CONVERTER (US, CND)
0 T901
1-443-874-11 TRANSFORMER, CONVERTER (AEP, UK)
0 T902
1-443-650-11 TRANSFORMER, CONVERTER
************************************************************
POWER-SW BOARD
****************
< SWITCH >
S806
1-786-033-41 SWITCH, TACTILE (I/1)
************************************************************
126
20%
20%
20%
20%
50V
50V
50V
50V
50V
50V
50V
50V
16V
50V
< CONNECTOR >
CN701
CN702
CN703
* CN710
1-779-564-21
1-785-329-11
1-785-328-11
1-506-486-11
CONNECTOR, FFC (LIF (NON-ZIF)) 27P
PIN, CONNECTOR (LIGHT ANGLE) 3P
PIN, CONNECTOR (LIGHT ANGRE) 2P
PIN, CONNECTOR 7P
< DIODE >
D701
D711
D721
8-719-921-44 DIODE MTZJ-5.1C
8-719-109-92 DIODE RD6.2ESB1
8-719-982-11 DIODE MTZJ-4.3B
< IC >
IC701
IC711
IC721
8-759-598-69 IC BA6956AN
8-759-598-69 IC BA6956AN
8-759-598-69 IC BA6956AN
< TRANSISTOR >
Q731
8-729-029-66 TRANSISTOR
DTC114ESA
< RESISTOR >
R701
R702
R711
R712
R721
1-249-415-11
1-247-807-31
1-249-415-11
1-247-807-31
1-249-415-11
CARBON
CARBON
CARBON
CARBON
CARBON
680
100
680
100
680
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R722
1-247-807-31 CARBON
100
5%
1/4W
R731
1-247-806-11 CARBON
91
5%
1/4W
R732
1-249-417-11 CARBON
1K
5%
1/4W
R733
1-249-429-11 CARBON
10K
5%
1/4W
R734
1-249-429-11 CARBON
10K
5%
1/4W
************************************************************
HCD-X1V
ROLLER MOTOR
Ref. No.
Part No.
ST ENCODER
Description
SENSOR
STOCKER MOTOR
Remark
Ref. No.
SW (1)
Part No.
1-686-726-13 ROLLER MOTOR BOARD
********************
SW (2)
SW (3)
Description
SW (4)
Remark
MISCELLANEOUS
**************
3
4
6
52
53
1-833-130-11
1-828-622-11
1-500-753-11
1-828-576-11
1-833-129-11
WIRE (FLAT TYPE) (8 CORE)
WIRE (FLAT TYPE) (19 CORE)
CLAMP, FERRITE
WIRE (FLAT TYPE) (11 CORE)
WIRE (FLAT TYPE) (11 CORE)
54
54
55
56
56
1-833-126-11
1-833-127-11
1-833-128-11
1-693-700-11
1-693-703-11
WIRE (FLAT TYPE) (9 CORE) (US, CND)
WIRE (FLAT TYPE) (11 CORE) (AEP, UK)
WIRE (FLAT TYPE) (11 CORE)
TUNER (FM/AM) (TM10SCE) (AEP, UK)
TUNER (FM/AM) (TM10SU) (US, CND)
0 58
0 58
59
102
104
1-777-071-23
1-783-820-11
1-500-386-11
1-828-659-11
1-828-621-11
CORD, POWER (AEP, UK)
CORD, POWER (US, CND)
FILTER, CLAMP (FERRITE CORE) (AEP, UK)
WIRE (FLAT TYPE) (27 CORE)
WIRE (FLAT TYPE) (19 CORE)
313
424
476
568
0 601
1-763-967-11
1-471-244-11
1-763-967-11
1-763-967-11
8-820-291-02
MOTOR, DC
MAGNET
MOTOR, DC
MOTOR, DC
OPTICAL PICK-UP BLOCK
************************************************************
ST ENCODER BOARD
*****************
(Included in RELAY BOARD, COMPLETE)
************************************************************
1-686-723-13 SENSOR BOARD
*************
< PHOTO SENSOR >
IC751
8-749-017-45 SENSOR, PHOTO RPR-220C1N
(DISC INSERT DETECT SENSOR)
************************************************************
1-686-725-13 STOCKER MOTOR BOARD
*********************
************************************************************
1-686-727-13 SW (1) BOARD
************
(KHM-310CAB/C2RP)
(Including sled motor, spindle motor)
< SWITCH >
0 601
8-820-322-04 OPTICAL PICK-UP BLOCK
S711
1-786-382-21 SWITCH, PUSH (1 KEY)(DISC INSERT (8/12cm)
************************************************************
1-686-728-13 SW (2) BOARD
************
604
0 F901
0 F901
M3000
< SWITCH >
S713
1-786-382-21 SWITCH, PUSH (1 KEY) (DISC IN (8/12cm))
S714
1-786-382-21 SWITCH, PUSH (1 KEY) (DISC IN (8cm))
************************************************************
1-686-729-13 SW (3) BOARD
************
1-787-396-11
M761
A-4735-953-A MOTOR (STOCKER) ASSY (STOCKER)
M771
A-4735-953-A MOTOR (STOCKER) ASSY (MODE)
M781
A-4735-953-A MOTOR (STOCKER) ASSY (ROLLER)
S702
1-477-299-11 ENCODER, ROTARY (STOCKER POSITION)
S771
1-477-300-11 ENCODER, ROTARY (MODE)
************************************************************
ACCESSORIES
************
< SWITCH >
S715
1-786-382-21 SWITCH, PUSH (1 KEY) (DISC OUT)
************************************************************
1-833-131-51
1-576-233-51
1-576-537-12
(KHM-313CAB/C2RP)
(Including sled motor, spindle motor)
CABLE, FLEXIBLE FLAT (24 CORE)
FUSE (H.B.C.) (T6.3AH/250V) (AEP, UK)
FUSE, GLASS TUBE (DIA.5) (8A/125V)
(US, CND)
D.C. FAN (50 SQUARE)
0
1-770-019-61 ADAPTOR, CONVERSION PLUG (UK)
1-686-730-13 SW (4) BOARD
************
< SWITCH >
S716
1-786-382-21 SWITCH, PUSH (1 KEY) (STOCKER IN/OUT)
S717
1-786-382-21 SWITCH, PUSH (1 KEY) (DISC POSITION)
S718
1-786-382-21 SWITCH, PUSH (1 KEY) (STOCKING)
***********************************************************
127
HCD-X1V
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
2
Ver.
Date
1.0
2006.07
Description of Revision
New