Camera Installation
CH A P T E R
2
Camera Installation
This chapter provides information and instructions for installing the Cisco Video Surveillance 3630 and
6630 IP cameras, and includes the following topics:
•
Installation Guidelines, page 2-1
•
Warnings Before Installation, page 2-1
•
Installing the IP Camera with a Vandal Resistant Enclosure, page 2-4
Installation Guidelines
This section describes how to install the IP camera. Before installing, review these guidelines:
•
The IP camera requires a network cable and a connection to a standard 10/100BaseT router or
switch. To power the IP camera with Power over Ethernet (PoE), a switch must be 802.3af
compliant.
•
If you are using the IP camera on a network connection that does not provide PoE, you must use a
Cisco 12 VDC power adapter (Cisco part number CIVS-PWRPAC-12V) or a third-party 24 VAC
power adapter.
•
If you are using an external speaker, microphone, input device, or output device, you must configure
additional settings after installing and performing the initial set up of the IP camera before the
external device can fully operate. For detailed information about these settings, see the Cisco Video
Surveillance 6000 Series IP Camera Configuration Guide.
•
If you do not connect an external device (speaker, microphone, input, or output) when you perform
the following installation procedure, you can install any of these devices later.
Warnings Before Installation
•
Power off the IP camera if smoke or unusual
odors are detected.
Contact your Cisco representative if these
situations occur.
•
Keep the IP camera away from water. If the
IP Camera becomes wet, power off
immediately.
Contact your Cisco representative if this
situation occurs.
Cisco Video Surveillance 3630 and 6630 IP Camera Installation Guide
2-1
Chapter 2
Camera Installation
Warnings Before Installation
•
Do not place the IP camera near sources of
heat, including televisions or ovens.
•
See the data sheet for operating
temperatures.
•
Keep the IP camera away from direct
sunlight.
•
Do not place the IP camera in high
humidity environments.
•
Do not place the IP camera on unsteady
surfaces.
•
Do not touch the IP camera during a
lightning storm.
•
Do not disassemble the IP camera.
•
Do not drop the IP camera.
Cisco Video Surveillance 3630 and 6630 IP Camera Installation Guide
2-2
Chapter 2
Camera Installation
Warnings Before Installation
•
Do not put sharp or tiny objects into the IP
camera.
Warning
Installation of the equipment must comply with local and national electrical codes. Statement 1074
Warning
The power supply must be placed indoors. Statement 331
Note
If you use the IP camera outdoors, place the camera and the power supply in a suitable NEMA
enclosure.
Warning
This product must be connected to a power-over-ethernet (PoE) IEEE 802.3af compliant power source
or an IEC60950 compliant limited power source. Statement 353
Caution
Inline power circuits provide current through the communication cable. Use the Cisco provided cable or
a minimum 24AWG communication cable.
Note
The power adapter that you use with the IP camera must provide power that is within +/–10% of the
required power.
Note
The equipment is to be connected to a Listed class 2, limited power source.
Cisco Video Surveillance 3630 and 6630 IP Camera Installation Guide
2-3
Chapter 2
Camera Installation
Installing the IP Camera with a Vandal Resistant Enclosure
Installing the IP Camera with a Vandal Resistant Enclosure
To install the IP camera to using a vandal resistant (VR) enclosure, perform the following steps.
Procedure
Step 1
Attach the included installation template/alignment sticker to the ceiling or wall.
Step 2
Using the circle marks on the sticker, drill at least two pilot holes symmetrically on each side (four holes
total) into the ceiling or wall, then put the provided wall plugs into the holes.
Use a hammer to drive the wall plugs into the holes, if needed.
Step 3
Secure the mounting plate to the ceiling or wall with the four included M4 x 25 screws.
Step 4
Take either of these actions to feed the cables to the IP camera:
Step 5
•
Cut out a section of the ceiling or wall that corresponds to the triangular cutout on the installation
template/alignment sticker and feed cables through a ceiling or wall.
•
Use a screwdriver to remove the cutout on the side of the conduit base, connect a cable conduit, and
feed the cables through the side of the conduit base.
Take these actions to install and connect an RJ45 Ethernet cable (24AWG [0.51 mm] gauge
recommended).
a.
Drill a hole on the rubber seal plug and insert an Ethernet cable (without a connector) through the
opening.
Cisco Video Surveillance 3630 and 6630 IP Camera Installation Guide
2-4
Chapter 2
Camera Installation
Installing the IP Camera with a Vandal Resistant Enclosure
b.
Strip about 1/2 inch (12 mm) of the sheath from the Ethernet cable.
c.
Use an RJ45 crimping tool to attach the Ethernet wires to a connector. When done, connect the cable
to the camera’s Ethernet RJ45 socket.
o: white/orange stripe
O: orange solid
g: white/green stripe
B: blue solid
b: white/blue stripe
G: green solid
br: white/brown stripe
BR: brown solid
d.
o
O
g
B
b
G
br
BR
1
2
3
4
5
6
7
8
Press the Ethernet cable into the routing path at the bottom of the camera so that the cable will not
get in the way when the metal mounting plate is attached.
Cisco Video Surveillance 3630 and 6630 IP Camera Installation Guide
2-5
Chapter 2
Camera Installation
Installing the IP Camera with a Vandal Resistant Enclosure
Step 6
(Optional) Take these actions to install and connect an external power cable and I/O cables for external
devices:
a.
Disassemble the components of the waterproof connector into parts (A) through (F).
Sealing Nut (A)
Housing (B)
Seals (C)
Seal (D)
Screw Nut (E)
Hex Nut (F)
b.
Place the screw nut (E) on the power and I/O cable opening.
c.
Feed the power cable through the waterproof connector (F --> D --> C--> B --> A). Be sure to feed
enough power cable length through the waterproof connector to connect the power cable to the GPIO
block.
Note
d.
There are 8 holes on the seal (D), and the widest holes with a crack on the side are specific
for power cables.
Feed the I/O cables through the waterproof connector (F --> E --> D --> C --> B --> A). Be sure to
feed enough I/O cable length through the waterproof connector to connect the I/O cable to the GPIO
block.
The recommended cable gauge is from 2.0 to 2.8 mm.
Cisco Video Surveillance 3630 and 6630 IP Camera Installation Guide
2-6
Chapter 2
Camera Installation
Installing the IP Camera with a Vandal Resistant Enclosure
e.
Push the seal (D) into the housing (B).
f.
Insert the seals (C) into unused holes on the seal (D) to avoid moisture.
g.
Secure the sealing nut (A) and hex nut (F) tightly from the bottom of the camera.
h.
Connect the power and I/O cables to the GPIO terminal block (see Figure 1-2 on page 1-4).
Step 7
Use the included allen wrench to secure the conduit base to the mounting plate by using three screws.
Step 8
Remove the black cover.
Step 9
(Optional) Use mini cable with BNC connector to temporarily attach an NTSC or PAL compliant analog
video display device to the analog video out port on the rear of the IP camera.
Note
The mini cable with BNC adapter is included in the audio/video cables accessory kit, which you can
purchase from Cisco (Cisco part number CIVS-AVCABLE).
Cisco Video Surveillance 3630 and 6630 IP Camera Installation Guide
2-7
Chapter 2
Camera Installation
Installing the IP Camera with a Vandal Resistant Enclosure
Analog video is enabled by default to allow you to adjust the camera field of view during installation.
However, it is not supported as a normal camera feed and is automatically disabled when any of the
following camera settings are made:
Note
Step 10
•
The primary video stream frame rate must be set higher than 15 fps.
•
The secondary video stream must is enabled.
We recommend that you disable analog video after installation. To disable analog video, see the Cisco
Video Surveillance 6000 Series IP Camera Configuration Guide.
While viewing video from the IP camera, take these actions to adjust the 3-axis field of view:
a.
Grip the two tilt adjustment screws and pan the IP camera left or right.
b.
Loosen the two tilt adjustment screws, tilt the IP camera, then tighten the screws.
c.
Rotate the IP camera to adjust the horizontal orientation until you achieve a level image.
Step 11
(Optional) Use the Focus, Tele, and Wide buttons on the IP camera to adjust the video image as desired
(see Figure 1-1 on page 1-2).
Step 12
Remove the wrapper from the included silica gel pack and use the included double-sided tape to attach
the pack inside the VR housing. Make sure that the silica gel pack does not obstruct the IP camera field
of view.
Step 13
Install the black cover.
Step 14
Attach the dome cover to the camera by aligning it with the mounting holes.
Step 15
Use the included allen wrench to tighten the four dome cover screws to secure the dome cover to the
camera. Make sure all parts of the camera are securely installed.
Cisco Video Surveillance 3630 and 6630 IP Camera Installation Guide
2-8
Chapter 2
Camera Installation
Installing the IP Camera with a Vandal Resistant Enclosure
What to do next
Complete the following procedures:
•
After you install the IP camera, follow the instructions in Chapter 3, “Performing the Initial Setup
of the IP Camera,” to access the IP camera through your network.
•
After completing the initial setup, use the IP camera user interface to adjust the focal length and
zoom factor. For more information, see the “Adjusting the IP Camera Focus and Zoom” section on
page 4-3.
Cisco Video Surveillance 3630 and 6630 IP Camera Installation Guide
2-9
Chapter 2
Installing the IP Camera with a Vandal Resistant Enclosure
Cisco Video Surveillance 3630 and 6630 IP Camera Installation Guide
2-10
Camera Installation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement