DeweCatalog_2012_DEW..

DeweCatalog_2012_DEW..
With the battery option, you can
hot-swap the batteries when needed,
keeping the system running indefinitely.
STG models are compatible with all
MSI-BR adapters, for maximum sensor
compatibility
DEWE-214 with optional battery pack
(battery pack fastens to the bottom of
the chassis)
DEWE-214 series
www.dewamerica.com/Products/DEWE-214
OVERVIEW
The DEWE-214 is our top of the line IN VEHICLE
testing instrument. It’s small size and power system
were specifically designed for mobile/vehicle
applications. It’s quite at home in your car, truck,
motorcycle, tank, military vehicle, train, boat, NASCAR
vehicle...
The analog inputs are extremely flexible, and the A/D
system behind them is top-notch: 24-bit resolution
for the highest dynamic range, 200 kS/s/ch sampling
(max), simultaneous sampling, brick wall anti-aliasing
filtering, and more.
The DEWE-214 also features two high speed CAN
bus interfaces supporting CAN and J1939 protocols
(OBD II optional). There are also digital I/O lines and
two counter inputs compatible with tachometers and
encoders.
Choose which conditioner you want, then what speed
of GPS sensor you would like: 1, 20, or 100 Hz.
52
Dewetron PRODUCT SELECTION GUIDE
◙◙ 8 high performance analog channels, 200
kS/s/ch simultaneous sampling
◙◙ Anti-aliasing filtering standard
◙◙ 24-bit resolution for highest dynamic range
◙◙ DS-7-SE software included
◙◙ Available in two basic versions with three
choice of GPS speeds
◙◙ 32 GB SLC solid state HDD (upgradable to
64, 128, 256 GB)
◙◙ Optional MOBILE display
◙◙ Keyboard and mouse included
◙◙ Wide range DC power input 8~30 VDC
◙◙ Battery power option - runs 2-3 hours
without any external power connected
◙◙ Batteries are hot-swappable - even during
measurement
◙◙ Ruggedized construction, MIL-STD, ENSTD, and more
◙◙ Full year warranty
Applications
◙◙
In-vehicle data acquisition
◙◙
Cars, trucks, motorcycles, trains
◙◙
Race cards - NASCAR, Formula 1, Indy...
◙◙ Aircraft, boats and ships
◙◙
Military vehicle test
◙◙
Field service and field test applications
◙◙
Noise & vibration
◙◙ All kinds of trouble-shooting
◙◙
Every kind of mechanical and structural test
◙◙
Every kind of MOBILE and VEHICLE test
MADE FOR THE ROAD
The DEWE-214 was designed specifically for invehicle testing. It starts with the wide-range DC
power input (8~30VDC), and its amazingly small
size and convenient form factor. Anchor points on
the sides make it easy to strap down in a moving
vehicle.
And the performance cuts no corners: 24-bit
resolution for incredible dynamic range. The built-in
GPS, including 20 and 100 Hz receivers is ideal for
dynamic testing, like brake and accel testing, ride
and handling, driveability, and more.
Small but essential features like these
tie-down “anchor” points, are standard
in the DEWE-214.
MOBILE display option
The MOB-DISP-17 (option) is a great add-on for
any portable DEWE system, especially for invehicle applications. This is a ruggedized display
with a capacitive touchscreen (supports multi-touch
software!) that’s brighter than ever.
And we built three USB 2.0 interfaces into it, so you
can put the 214 in the trunk, and mount the MOB
display up front. Use the USBs to connect memory
sticks, or your keyboard, etc. Get the optional kit for
the suction cups and longer cables for in-vehicle
usage.
Dewetron PRODUCT SELECTION GUIDE
53
DEWE-214 configuration
DEWE-214-STG model with 1, 20, or 100 Hz GPS
The DEWE-214-STG model features our most FLEXIBLE analog inputs, based on the MDAQ-STG conditioner. It can
natively handle any kind of bridge or strain gage, with completion for half and quarter bridge sensors and various wiring
methods, amp and sensor balance, and so much more. You can input ±10V directly. Using our MSI-BR series adapters
you can also input IEPE accels and mics, charge sensors, thermocouples (J, K, T, C), RTD sensors (Pt100, 200, 500,
1000), voltages up to ±200V. We also offer ADAP series adapters for 4-20 mA sensors and simple BNC adapters.
Choose the GPS version you want, with 1, 20 or 100 Hz sensor.
The STG series is the more flexible of the two basic DEWE-214 models, and you can upgrade it to 16 channels!
DEWE-214-STG with optional channel expansion from 8 to 16 channels
(the standard model has the left-most 8 channels installed)
DEWE-214-ACC model with 1, 20, or 100 Hz GPS
Choose the DEWE-214-ACC model if you will be doing mostly IEPE inputs for noise, shock and vibration testing. There
are eight 80 kHz bandwidth inputs with TEDS support, which provide the constant current excitation needed by IEPE
accelerometers and microphones. You can input ±10V, ±2V, ±0.5 or ±0.1V directly. All of the analog inputs are on
convenient BNC connectors. Maximum analog sample rate is 204.8 kS/s/ch. Anti-aliasing filtering is standard, of course.
Choose the GPS version you want, with 1, 20 or 100 Hz sensor.
Both DEWE-214 models include two synchronous SUPER counters, which are ideal for tachs, tape, and RPM sensors as
well as encoders – and offer adjustable trigger levels, and input ranges beyond TTL. In addition, there are 8 TTL digital
inputs (ideal for measuring simple switch closures and "discrete" signals) and 8 TTL digital outputs (great for alarm
outputs, a standard software feature). All digital lines are available on the standard DB37 connector on the front panel.
LEMO connectors for the counters are available as an option (ORION-CNT2-LEMO).
54
Dewetron PRODUCT SELECTION GUIDE
Expansion via Ethernet
The NET expansion is a fantastic way to
combine two or more DEWE instruments to
one multichannel system. Each instrument
must have installed hardware option ORIONSYNC and software option DS-OPT-NET.
Synchronization of all units is required too.
There are two ways of synchronization: First
is a simple cable connection for distances up
to 200 m, second one is GPS- or IRIG-CLOCK
which is useful for long distances when a
cable connection is not possible. DS-OPTNET software offers full remote setup, online
data transfer up to the limit of the network
connection and offline data transfer between
the instruments.
DEWE-214
DEWE-214
SYNC
ETHERNE
T
DEWE-214
User tip: The NET expansion also distributes
the data processing load among multiple
computers, each of which can store data at full
speed.
GPS
(20Hz or 100Hz)
DEWE-214
Specifications
Specification
DEWE-214 STG
DEWE-214 ACC
Analog input channels
8 (upgrade to 16 channels optional)
8
Expandable to 16 channels
Yes (option 214-STG-08-16 adds 8 more STG channels, with the same specifications as the first 8 channels)
N/A
Digital I/O lines (TTL)
8 in / 8 out (inputs are TTL/CMOS level with pull-up with 100 kΩ). Low range: -0.7 to 0.8V; High range: 2 to 5V
Counter inputs
2 synchronous advanced counter / encoders
Counter specifications
32-bit resolution, 80 MHz clock (40 MHz max input frequency) 5 MHz bandwidth, 1 MΩ input impedance (5pF), trigger level adjustable 0-40V, ±100V over voltage input
protection, AC/DC input coupling (1 Hz HP filter with AC coupling), differential and symmetrical inputs, common voltage range: -35 to 50V
Trigger input
1 included, TTL Schmidt trigger, pull-up with 100 kΩ. Low range: -0.7 to 2V; High range: 3 to 5V
Signal conditioning
8 FLEXIBLE strain gage / voltage inputs, TEDS compatible
8 FLEXIBLE IEPE / voltage inputs, TEDS compatible
Measuring modes:
Full bridge, 1⁄2 bridge, 1⁄4 bridge 120 Ω, 1⁄4 bridge 350 Ω or ±10V voltage
Full bridge sensors 120 Ω to 10 kΩ
Internal completion for 1⁄2 bridge and 1⁄4 bridge sensors
Internal 50 kΩ and 100 kΩ shunt resistors
Voltage: ±0.125 V, 0.25 V, 0.5 V, 1 V, 1.25 V, 2.5 V, 5 V, 10 V
IEPE: 0.5, 1, 2, 4, 5, 10, 20, 40
Single ended or differential
DC or AC coupled (3 Hz standard, on request down to 0.1 Hz)
Analog connector
DB9
BNC
Max sample rate
204.8 kS/s/ch
204.8 kS/s/ch
Analog bandwidth (-3 dB)
30 kHz
80 kHz
Bit resolution
24-bit
24-bit
Anti-aliasing filtering
Automatic
Automatic
MSI compatible
Yes
No
MSI adapters available
MSI-BR-ACC supports IEPE accels and mics; MSI-BR-CHA-50 supports dynamic
charge sensors; MSI-BR-V200 supports voltages up to ±200V; MSI-BR-RTD supports Pt100/Pt200/Pt500/Pt1000 RTDs; MSI-BR-TH supports J, T, K, or C thermocouples
N/A
Slow channel expansion
Via one or more EPAD2 and CPAD2 series isolated 8-channel signal conditioners. See EPAD2/CPAD2 section for the full range available
CAN BUS interfaces
2 high-speed CAN BUS interfaces standard, on DB9 connectors. Supports CAN 2.0B and J1939 protocols (OBD-II support requires software option).
GPS sensor
1 Hz standard (20 Hz and 100 Hz dynamic GPS sensor optional)
1 Hz standard (20 Hz and 100 Hz dynamic GPS sensor optional)
GPS sensor
Speed, position, direction (20/100 Hz GPS options also output distance, acceleration, Z height and acceleration, UTC time reference)
Speed, position, direction (20/100 Hz GPS options also output distance, acceleration, Z height and acceleration, UTC time reference)
VIDEO input
One USB camera can be used to add VIDEO to your data recordings. Compatible with all DirectX standard webcams.
Software included
DS-7-SE with CAN option. DS-7-SE is a complete data acquisition and analysis software package including unlimited setup file creation, on-line and off-line math channels
(including filtering, integration, and more), with scope, recorder, FFT, GPS map, VIDEO, analog and digital meter displays, and much more.
Main system
Hard disk
32 GB SLC solid state HDD, upgradable to 64 GB, 128 GB, or 256 GB. Data throughput to disk: typ. 40 MB/s continuous
Power supply
8 ~ 30 VDC wide range DC power input, including external AC/DC adapter, and DC cable with cigarette lighter plug
Display
Optional MOB-DISP-17 (1280x1024 px, high brightness, capacitive touchscreen (USB interface)
Processor
Intel® Core2Duo 2 GHz
RAM
2 GB (expandable to 3 GB)
Interfaces built-in
2 x 1 Gb ethernet; WLAN (WIFI) including attachable antenna, 4 x USB 2.0, LEMO connector for Dewetron EPAD2 series modules
Operating system
Microsoft Windows7 32-bit
Dimensions (W x D x H)
317 x 252 x 92 mm (12.5 x 9.9 x 3.6 in.)
Weight
Typ. 5 kg (11 lb.)
Operating temperature
0 to 50°C (-20°C when unit is pre-warmed and not powered off at temperatures below 0°C)
Humidity
10 to 80% non-condensing; 5 to 95% relative humidity
Shock and Vibration
Shock: EN 60068-2-27 ; Vibration: EN 60068-2-6, EN 60721-3-2 class 2M2, better than MIL-STD-810F (for shock and vibration)
Dewetron PRODUCT SELECTION GUIDE
55
DEWE-214 interfaces
Two High-speed CAN BUS interfaces
Both DEWE-214 models feature two high-speed CAN
BUS interfaces compatible with the CAN 2.0B and
J1939 protocols. In the software you can import DBC
setup files, or create your CAN setup manually if you
like. There is a convenient "listen" function that scans
the bus and identifies any messages that are coming
across, and adds them to the list. It's easy to configure
the channels that are contained within each message by
bit range, name, scaling factor, and engineering units.
Everything gets saved into the setup file.
Configuring the channels within each message couldn’t be much easier.
CAN channels are just like any others in your Dewetron system. You can display
them, record them, use them in MATH, trigger from them... no restrictions.
OBD II interface capabilities
If you want to read the OBD II messages, there is a
software option for that. Simply configure either or both
CAN ports for OBD II, and the software will do the rest.
The software even includes an automatic listing of the
basic codes, already set up for you.
When OBD II has been configured for a CAN interface, these standard channels
are set up for you automatically. Just turn on the ones you want to record.
Use CAN for channel expansion, too
Dewetron CAN BUS interfaces can also be used
for connecting CAN based sensors, including our
own CPAD2 series 8 channel signal conditioners for
thermocouples, voltages, currents, and RTDs. See the
CONDITIONERS section for a full listing of the CPAD2
modules that are available today. We even put power on
two of the unused pins of the connector, so that we can
directly power our CPAD2 modules. This conveniently
eliminates the need to provide power to them separately.
But virtually any standard CAN output device can be
used with our CAN interfacess, including non-Dewetron
brand sensors and signal conditioners.
56
Dewetron PRODUCT SELECTION GUIDE
Typical Display:
Where other systems show you some
squiggly lines and maybe some
numbers, that’s where we start.
You can show and record VIDEO (see
below for details).
You can show and record CAN BUS
data (see previous page for details).
You can show and record GPS
data, both digitally as well as in a
graphical GPS track. Bring in one or
more satellite or map images and
position them behind the track (this
is easy to do).
You can show and record additional
data from our EPAD2 and CPAD2
conditioners, as well as third-party
CAN based sensors.
You can show and record SERIAL and
ETHERNET data from a wide variety
of third party devices (just add a
software plugin).
Then create as many screens as you
like in our software, and set them up
just the way that you like.
That’s data acquisition like no one
ever did it before.
That’s Dewetron.
WEB CAM / Gig-E CAM connection
Dewetron famously invented the use of common web
cameras with data acquisition systems nearly 10 years
ago. You can connect nearly every standard DirectX
video camera in the world (one maximum) to your
DEWE-214 and start recording video in sync with your
other data right away.
Or, for better performance, choose our DEWE-CAMGIGE-50 camera, and ethernet GIG-E camera!
VIDEO adds incredible context to your data acquisition.
AboveL DEWE-CAM-GIGE-50
Above: typical WEB cam
Inertial sensors for dynamic testing
We offer two inertial sensors for a wide variety of vehicle
test applications. There is a relativelyy inexpensive
XSENS MTi-G sensor that you can hold in your hand, for
basic applications.
But for high-end applications such as CAPS, driveability,
brake testing, etc. we offer the ADMA system from
GeneSys, completely integrated with your DEWE system.
See the SENSORS section for further details about both
inertial sensors.
Dewetron PRODUCT SELECTION GUIDE
57
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement