LevelOne IES-0883 network switch Quick Installation Guide

IES-0883

6 GE + 2 SFP Managed Switch -20 to 60C, DIN-rail

Quick Installation Guide

Default Setting

IP

Login

Password

Console

192.168.10.1 root

[blank]

115200, n, 8, 1 v1.00 - 1206

Overview

LevelOne IES-0883 Industry Ethernet Switch provides 8 ports of

Gigabit Ethernet plus 2 1000Base SFP slots to enable high speed network at mission-critical environment. This device is designed to be mounted on an industry standard DIN-rail, plus the clearly visible status LEDs provide simple monitoring of port link activity.

Moreover, the SFP slots support pluggable modules that enabling you to choose from a variety of transceivers.

Cost Effective

This device operates under -20 to 60 Celsius (-4 to 140 Fahrenheit) temperature that offers optimal suitability for industrial applications at low cost while maintaining all components built to withstand harsh environment applications without compromise reliability and stability.

Resilient Ring Network

Supports Ring topology network providing simple installation and ultra fast network recovery performance, less than 15ms. Unlike much complex resilient topology, such as a redundant star, the Ring simplifies the network design and requires less cabling installation.

In addition, fast network recovery time helps minimize system downtime.

IES-0883 Page 1

Physical Description

Front Panel Rear Panel

Features

 Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial environment.

 Manageable via SNMP, Web-based, Telnet, and RS-232 console port.

 Supports Command Line Interface in RS-232 console.

 Supports IEEE802.3/802.3u/802.3ab/802.3z/802.3x. Auto-negotiation:

10/100/1000Mbps, full/half-duplex. Auto MDI/MDIX.

 1000Base-SX/LX: Multi mode or Single mode SC type; 1000Base-BX: WDM Single mode SC type.

 Support 4096 MAC addresses. Provides 1M bits memory buffer.

 Store-and-forward mechanism.

 Full wire-speed forwarding rate.

 Alarms for power failure by relay output.

 Operating voltage and Max. current consumption: 1.7A @ 12VDC, 0.85A @

24VDC. Power consumption: 20.4W Max.

 Power supply: Redundant DC Terminal Block power inputs and 12VDC DC JACK with 100-240VAC external power supply.

 Field Wiring Terminal Markings: Use Copper Conductors Only, 60/75℃, wire range 12-24 AWG, torque value 7 lb-in.

 -20℃ to 60℃ (-4℉ to 140℉) operating temperature range. UL508 Industrial

Control Equipment certified Maximum Surrounding Air Temperature @ 60℃

(140℉).

 For use in Pollution Degree 2 Environment.

 Supports Din-Rail or Panel Mounting installation.

Package Contents

 IES-0883

 Quick Installation Guide

 CD User Manual / Utility

IES-0883 Page 2

Power Input

+

PW1

–

12 – 32VDC

Power Ground

PW2

+

–

12 – 32VDC

Power Ground

Earth Ground

Relay Output 1A @ 24VDC

Relay Alarm warning signal disable for following:

1. The relay contact closes if Power1 and Power2 are both failed but Power3 on

2. The relay contact closes if Power3 is failed but Power1 and Power2 are both on

 There are three power inputs can be used. Redundant power function is supported

PW3 is DC Jack type with 12VDC input

IES-0883 Page 3

LED Status

LED

PW 1,2,3

Status

Steady

Off

Power On

Power Off

Description

10/100/1000Base-TX & 1000Base-FX

Steady

LNK/ACT

Network connection established

Flashing Transmitting or Receiving data

Amber Connection at 1000Mbps speed

100 Green

Off

Connection at 100Mbps speed

Connection at 10Mbps speed

Alarm

Alarm

Steady

Off

State the power redundancy failure has being addressed

State the power redundancy failure has not being addressed

IES-0883 Page 4

Terminal Mode). And the “switch_a(config)#” prompt will show on the screen.

12. Set new IP address and subnet mask for Switch:

13. At the “switch_a(config)#” prompt just type in “interface vlan1.1” and press <Enter> to logon to vlan 1 (vlan1.1 means vlan 1). And the “switch_a(config-if)#” prompt will show on the screen.

14. Command Syntax: “ip address A.B.C.D/M”. “A.B.C.D” specifies

IP address. “M” specifies IP subnet mask. “M”= 8: 255.0.0.0,

16:255.255.0.0, or 24: 255.255.255.0.

15. For example, At the “switch_a(config-if)#” prompt just type in

“ip address 192.168.1.10/24” and press <Enter> to set new IP address (192.168.1.10) and new IP subnet mask (255.255.255.0) for Switch

Console Configuration

1. Connect to the switch console:

2. Connect the DB9 straight cable to the RS-232 serial port of the device and the RS-232 serial port of the terminal or computer running the terminal emulation application. Direct access to the administration console is achieved by directly connecting a terminal or a PC equipped with a terminal-emulation program

(such as HyperTerminal) to the switch console port.

3. Configuration settings of the terminal-emulation program:

4. Baud rate: 115,200bps, Data bits: 8, Parity: none, Stop bit: 1, Flow control: none.

5. Press the “Enter” key. The Command Line Interface (CLI) screen should appear as below:

6. Logon to Exec Mode (View Mode):

7. At the “switch_a login:” prompt just type in “root” and press

<Enter> to logon to Exec Mode (or View Mode). And the

“switch_a>” prompt will show on the screen.

8. Logon to Privileged Exec Mode (Enable Mode):

9. At the “switch_a>” prompt just type in “enable” and press

<Enter> to logon to Privileged Exec Mode (or Enable Mode). And the “switch_a#” prompt will show on the screen.

10. Logon to Configure Mode (Configure Terminal Mode):

11. At the “switch_a#” prompt just type in “configure terminal” and press <Enter> to logon to Configure Mode (or Configure

IES-0883 Page 5

Web Configuration

1. Login the switch:

2. Specify the default IP address (192.168.1.10) of the switch in the web browser. A login window will be shown as below:

3. Enter the factory default login ID: root.

4. Enter the factory default password (no password).

5. Then click on the “Login” button to log on to the switch.

IES-0883 Page 6

Note: Please refer to User Manual for more detailed information

IES-0883 Page 7