Champion Power Equipment 100166 Instructions / Assembly

OWNER’S MANUAL & OPERATING INSTRUCTIONS
1 INCH
Water pump with hose Kit
MODEL NUMBER
100166
SAVE THESE INSTRUCTIONS
Important Safety Instructions
are included in this manual.
MADE IN CHINA
REV 100166-20150126
12039 Smith Ave.
Santa Fe Springs CA 90670
USA / 1-877-338-0999
www.championpowerequipment.com
AN IMPORTANT MESSAGE ABOUT TEMPERATURE:
Your Champion Power Equipment product is designed and rated for continuous operation at ambient temperatures up to
40°C (104°F). When your product is needed your product may be operated at temperatures ranging from -15°C (5°F) to
50°C (122°F) for short periods. If the product is exposed to temperatures outside this range during storage, it should be
brought back within this range before operation. In any event, the product must always be operated outdoors, in a
well-ventilated area and away from doors, windows and other vents.
Have questions or need assistance?
Do not return this product to the store!
WE ARE HERE TO HELP!
Visit our website:
www.championpowerequipment.com
for more info:
• Product Info & Updates
• Frequently Asked Questions
• Tech Bulletins
• Product Registration
– or –
Call our Customer Care Team Toll-Free at:
1-877-338-0999
WARNING:
The Engine Exhaust from this product contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
*We are always working to improve our products. Therefore, the enclosed product may differ slightly from the image on the cover.
100166
1 INCH
Water pump with hose kit
Table of Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Manual Conventions. . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Controls and Features . . . . . . . . . . . . . . . . . . . . . . 5
Water pump. . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Parts Included . . . . . . . . . . . . . . . . . . . . . . . . . 6
Hose Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Other . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Remove the Water pump
from the Shipping Carton. . . . . . . . . . . . . . . . . . 7
Install the Handle. . . . . . . . . . . . . . . . . . . . . . . 7
Add Engine Oil. . . . . . . . . . . . . . . . . . . . . . . . . 8
Add Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Water pump Location. . . . . . . . . . . . . . . . . . . . 10
Priming the Pump. . . . . . . . . . . . . . . . . . . . . . 10
Connecting the Inlet Hose . . . . . . . . . . . . . . . . 11
Connecting the Outlet Hose . . . . . . . . . . . . . . . 11
Starting the Engine. . . . . . . . . . . . . . . . . . . . . 13
Stopping the Engine . . . . . . . . . . . . . . . . . . . . 13
Maintenance and Storage. . . . . . . . . . . . . . . . . . . 14
Engine Maintenance . . . . . . . . . . . . . . . . . . . . 14
Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Spark Plugs. . . . . . . . . . . . . . . . . . . . . . . . 15
Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Adjustments. . . . . . . . . . . . . . . . . . . . . . . . 15
Maintenance Schedule. . . . . . . . . . . . . . . . . 16
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Engine Storage. . . . . . . . . . . . . . . . . . . . . . 16
Water pump Storage . . . . . . . . . . . . . . . . . . 16
Winter Storage. . . . . . . . . . . . . . . . . . . . . . 17
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Engine Specifications . . . . . . . . . . . . . . . . . . . 18
Water pump Specifications. . . . . . . . . . . . . . . . 18
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Maintenance Valve Clearance . . . . . . . . . . . . . . 18
An Important Message About Temperature. . . . . 18
Parts Diagram. . . . . . . . . . . . . . . . . . . . . . . . . 19
Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Engine Parts Diagram . . . . . . . . . . . . . . . . . . . 21
Engine Parts List . . . . . . . . . . . . . . . . . . . . . . 22
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . 23
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Warranty Qualifications . . . . . . . . . . . . . . . . . . 24
Repair/Replacement Warranty. . . . . . . . . . . . . . 24
Do Not Return The Unit To
The Place Of Purchase. . . . . . . . . . . . . . . . . . . 24
Warranty Exclusions. . . . . . . . . . . . . . . . . . . . 24
Normal Wear . . . . . . . . . . . . . . . . . . . . . . . 24
Installation, Use and Maintenance. . . . . . . . . 24
Other Exclusions. . . . . . . . . . . . . . . . . . . . . 24
Limits of Implied Warranty and Consequential
Damage. . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Contact Information. . . . . . . . . . . . . . . . . . . . . 24
Address. . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Customer Service. . . . . . . . . . . . . . . . . . . . 24
Technical Service . . . . . . . . . . . . . . . . . . . . 24
ENGLISH 100166
Introduction
Introduction
Congratulations on your purchase of a Champion Power Equipment product. Champion Power Equipment and
Champion Engine Technology designs, builds, and supports all of our products to strict specifications and guidelines.
With proper product knowledge, safe use, and regular maintenance, this product should bring years of satisfying
service.
Every effort has been made to ensure the accuracy and completeness of the information in this manual, and we
reserve the right to change, alter and/or improve the product and this document at any time without prior notice.
Since CPE/CET highly value how our products are designed, manufactured, operated and are serviced, and also
highly value your safety and the safety of others, we would like you to take the time to review this product manual
and other product materials thoroughly and be fully aware and knowledgeable of the assembly, operation, dangers
and maintenance of the product before use. Fully familiarize yourself, and make sure others who plan on operating
the product fully familiarize themselves too, with the proper safety and operation procedures before each use. Please
always exercise common sense and always error on the side of caution when operating the product to ensure no
accidents, property damage, or injury occurs. We want you to continue to use and be satisfied with your CPE/CET
product for years to come.
Record the model and serial numbers as well as date and place of purchase for future reference. Have this
information available when ordering parts and when making technical or warranty inquiries.
Champion Power Equipment Support
1-877-338-0999
Model Number
100166
Serial Number
Date of Purchase
Purchase Location
For Oil Type see ‘Add Engine Oil‘ section. For Fuel Type see ‘Add Fuel‘ section.
1
100166 ENGLISH
Manual Conventions
This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol
is used with a key word to alert you to potential hazards in operating and owning power equipment.
Follow all safety messages to avoid or reduce the risk of serious injury or death.
DANGER
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury.
WARNING
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
CAUTION
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which, if
not avoided, may result in property damage.
NOTE
If you have questions regarding your water pump,
we can help. Please call our help line at 1-877-338-0999
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in minor
or moderate injury.
2
ENGLISH 100166
Safety Rules
WARNING
Read this manual thoroughly before operating your
water pump. Failure to follow instructions could
result in property damage, serious injury or death.
DANGER
DO NOT pump gasoline or fuel, fuel-oil mixtures,
detergents, acids, chemicals, beverages, pesticides,
fertilizers or any other flammable liquid or corrosive.
Pumping volatile liquids may result in an explosion
or fire. These liquids will corrode the pump and void
the warranty.
WARNING
The engine exhaust from this product contains
chemicals known to the state of California to cause
cancer, birth defects, or other reproductive harm.
DANGER
Engine exhaust contains carbon monoxide, a
colorless, odorless, poison gas. Breathing carbon
monoxide will cause nausea, dizziness, fainting or
death. If you start to feel dizzy or weak, get to fresh
air immediately.
Operate water pump outdoors only in a well
ventilated area DO NOT operate the water pump
inside any building, enclosure or compartment.
DO NOT allow exhaust fumes to enter a confined
area through windows, doors, vents or other openings.
DANGER
Rotating parts can entangle hands, feet, hair,
clothing and/or accessories.
Traumatic amputation or severe laceration can result.
Keep hands and feet away from rotating parts. Tie
up long hair and remove jewelry. Operate equipment
with guards in place. DO NOT wear loose-fitting
clothing, dangling drawstrings or items that could
become caught.
DANGER
The water pump develops powerful force.
DO NOT move the water pump when it is in use. DO
NOT use hoses or connectors that are worn, damaged
or frayed. DO NOT allow children or unqualified persons
to operate or service the water pump. DO NOT open
top plug or drain plug.
WARNING
DO NOT immerse this unit in water.
WARNING
Sparks can result in fire or electrical shock.
When servicing the water pump:
Disconnect the spark plug wire and place it where
it cannot contact the plug. DO NOT check for spark
with the plug removed. Use only approved spark
plug testers.
CAUTION
Pumping solids through the pump, impeller or
hoses is not recommended.
3
100166 ENGLISH
DANGER
Fuel and fuel vapors are highly flammable and
extremely explosive.
Fire or explosion can cause severe burns or death.
Unintentional startup can result in entanglement,
traumatic amputation or laceration.
When adding or removing fuel:
Turn the engine off and let it cool for at least two
minutes before removing the fuel cap. Loosen the
cap slowly to relieve pressure in the tank.
Only fill or drain fuel outdoors in a well-ventilated area.
DO NOT pump gas directly into the tank at the gas
station. Use an approved container to transfer the
fuel to the tank.
DO NOT overfill the fuel tank.
Always keep fuel away from sparks, open flames,
pilot lights, heat and other sources of ignition.
DO NOT light or smoke cigarettes.
When starting the engine:
DO NOT attempt to start a damaged engine. Make
certain that the gas cap, air filter, spark plug,
fuel lines and exhaust system are properly in
place. Allow spilled fuel to evaporate fully before
attempting to start the engine.
Make certain that the water pump is resting firmly
on level ground.
When operating the water pump:
DO NOT move or tip the water pump during
operation.
DO NOT tip the water pump or allow fuel or oil to
spill from the engine.
When transporting, servicing or storing the water
pump:
Make certain that the fuel tank is empty.
Disconnect the spark plug wire.
Store away from sparks, open flames, pilot lights,
heat and other sources of ignition.
WARNING
Water pumped through this unit shall not be used
as drinking water.
Safety Rules
WARNING
DO NOT pump salt, sludge, sewer, sea, or any other
type of water containing solid material.
WARNING
Rapid retraction of the starter cord will pull hand and
arm towards the engine faster than you can let go.
Unintentional startup can result in entanglement,
traumatic amputation or laceration.
Broken bones, fractures, bruises or sprains could
result.
When starting engine, pull the starter cord slowly
until resistance is felt and then pull rapidly to avoid
kickback.
CAUTION
Exceeding the water pump’s specification for
maximum head can damage the water pump and/or
hose kits connected to it.
DO NOT modify the water pump in any way. DO
NOT attempt to exceed the rated flow. Attempting
to increase the rated flow may damage the unit
and/or shorten its life.
CAUTION
Improper treatment or use of the water pump can
damage it, shorten its life and void your warranty.
Use the water pump only for intended uses. Operate
only on level surfaces. DO NOT expose water pump
to excessive moisture, dust, or dirt.
DO NOT allow any material to block the cooling slots.
DO NOT use the water pump if:
–– Equipment sparks, smokes or emits flames
–– Equipment vibrates excessively
4
ENGLISH 100166
Controls and Features
Read this owner’s manual before operating your water pump. Familiarize yourself with the location and function of the
controls and features. Save this manual for future reference.
Water pump
4
12
3
5
11
13
10
9
2
1
8
7
6
(1) Drain Plug
(9) Recoil Starter – Used to start the engine.
(2) 1 in. (2.5 cm) Inlet – 1 in. (2.5 cm) inlet
connector.
(10) Priming Button – Used to prime fuel for starting.
(3) 1 in. (2.5 cm) Outlet – 1 in. (2.5 cm) outlet
connector.
(12) Spark Plug and Connector Wire
(4) Handle
(5) Air Filter – Protects the engine by filtering dust
and debris from the air intake.
(6) Fuel Tank – 0.145 gal. (550 mL) capacity fuel
tank.
(7) Throttle Lever – Used to adjust engine speed.
(8) Off Button – Press to stop the unit.
5
(11) Choke lever– Used to start the engine.
(13) Muffler
100166 ENGLISH
Controls and Features
Parts Included
Your model 100166 gasoline powered water pump ships
with the following parts:
Hose Kit
––
––
––
––
––
––
16.4 ft. x 1 in. (5 meter x 25mm) Intake Hose . . . .
26.2 ft. x 1 in. (8 meter x 25mm) Discharge Hose. .
Hose Connector with Rubber gasket (Straight ) . . . .
Hose Connector with Rubber gasket (90º ) . . . . . . .
Intake Filter Screen. . . . . . . . . . . . . . . . . . . . . . .
Hose Clamps . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
3
Other
–– Tool Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
–– Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
–– Nut, M12x1.25 (for handle) . . . . . . . . . . . . . . . . . 1
6
ENGLISH 100166
Assembly
Your water pump requires some assembly. This unit
ships from our factory without oil. It must be properly
serviced with fuel and oil before operation.
If you have any questions regarding the assembly of
your water pump, call our help line at 1-877-338-0999.
Please have your serial number and model number
available.
Remove the Water pump from the Shipping Carton
1. Set the shipping carton on a solid, flat surface.
2. Remove everything from the carton except the
water pump.
3. Carefully cut each corner of the box from top to bottom.
Fold each side flat on the ground.
Install the handle
1. Hand thread the M12x1.25 nut onto the handle base,
up to a point where it naturally stops. (A)
2. DO NOT try to thread the nut after that stop point
with any wrench, pilers, or other device.
3. Hand thread the handle/nut combo into the threaded
hole on the pump side cover top. (B)
A
B
4. Once securely tightened the handle should face away
from the outlet and towards the engine. (C)
C
D
7
Install the handle Cont’d.
CAUTION
Hand tighten the nut and handle only. Any excess
force, with tools or otherwise, may strip or break
the threads on the handle or side cover hole.
NOTE
There will be some threading left on the handle that
will stick out of the nut after installation is secured.
This is normal and should be left unthreaded. (D)
100166 ENGLISH
Assembly
Add Engine Oil
Add Engine Oil Cont’d.
CAUTION
NOTE
DO NOT attempt to crank or start the engine before
it has been properly filled with the recommended
type and amount of oil. Damage to the water pump
as a result of failure to follow these instructions will
void your warranty.
Check oil often during the break-in period. Refer to the
Maintenance section for recommended service intervals.
CAUTION
The engine is NOT equipped with a low oil shut-off
sensor and will NOT stop when the oil level in the
crankcase falls below the threshold level.
NOTE
The recommended oil type is 10W-30 automotive oil.
NOTE
1. Place the water pump on a flat, level surface.
2. Remove oil fill cap/dipstick to add oil. (A)
Weather will affect engine oil and engine
performance. Change the type of engine oil used
based on weather conditions to suit the engine
needs.
Degrees Celsiusº (Outside)
A
Full Synthetic 5W-30
3. Using a funnel (not included) add up to 2.4 ounces
(70 mL) of oil and replace oil fill cap/dipstick. (B)
4. It is recommended to only fill to the base of the oil fill
hole. DO NOT OVERFILL. (B)
5. Check engine oil level daily and add as needed.
B
Degrees Fahrenheitº (Outside)
NOTE
We consider the first 5 hours of run time to be the
break-in period for the engine. During the break in
period we recommend using standard automotive
non-synthetic blended oils. After the break in
period synthetic lubricant can be used but is not
required. Adjusting throttle setting will increase/
decrease engine speed helping to seat piston
rings. Avoid bogging or lugging the engine down
and avoid prolonged running at constant RPM.
After the 5 hour break-in period, change the oil.
Using synthetic lubricants does not increase the
recommended oil change interval.
NOTE
Once oil has been added, a visual check should show
oil about 1-2 threads from running out of the fill hole.
If using the dipstick to check oil level, DO NOT screw
in the dipstick while checking.
8
ENGLISH 100166
Assembly
Add Fuel
1. Use clean, fresh, regular unleaded fuel with a
minimum octane rating of 85 and an ethanol content
of less than 10% by volume.
2. DO NOT mix oil with fuel.
3. Clean the area around the fuel cap.
4. Remove the fuel cap.
5. Slowly add fuel to the tank. DO NOT OVERFILL. Fuel
can expand after filling. Space must be left in the tank
for fuel expansion. Fuel can be forced out of the tank
as a result of expansion if it is overfilled, and can affect
the stable running condition of the product. When filling
the tank, it is recommended to leave enough space for
the fuel to expand.
6. Screw on the fuel cap and wipe away any spilled fuel.
Add Fuel Cont’d.
CAUTION
Use regular unleaded gasoline with a minimum
octane rating of 85.
Do not mix oil and gasoline.
Do not overfill tank, leave room.
DO NOT pump gas directly into the generator at the
gas station. Use an approved container to transfer
the fuel to the generator.
DO NOT fill fuel tank indoors.
DO NOT fill fuel tank when the engine is running or hot.
DO NOT overfill the fuel tank.
DO NOT light cigarettes or smoke when filling the
fuel tank.
NOTE
WARNING
Pouring fuel too fast may result in blow back of fuel at
the operator while filling.
9
Our engines work well with 10% or less ethanol
blend fuels. When using blended fuels there are
some issues worth noting:
–– Ethanol-gasoline blends can absorb more water
than gasoline alone.
–– These blends can eventually separate, leaving
water or a watery goo in the tank, fuel valve and
carburetor.
–– With gravity-fed fuel supplies, this compromised
fuel can be drawn into the carburetor and cause
damage to the engine and/or potential hazards.
–– There are only a few suppliers of fuel stabilizer
that are formulated to work with ethanol blend
fuels.
–– Any damages or hazards caused by using
improper fuel, improperly stored fuel, and/
or improperly formulated stabilizers, are not
covered by manufacture’s warranty.
It is advisable to always shut off the fuel supply,
run the engine to fuel starvation and drain the tank
when the equipment is not in use for more than 30
days.
100166 ENGLISH
Operation
Water pump Location
Priming the Pump
Place the water pump in a well ventilated area. DO
NOT place the water pump near vents or intakes where
exhaust fumes could be drawn into occupied or confined
spaces. Carefully consider wind and air currents when
positioning water pump.
This water pump must have at least 5 ft. (1.5 m) of
clearance from combustible material. Leave at least
3 ft. (91.4 cm) of clearance on all sides of the water
pump to allow for adequate cooling, maintenance and
servicing.
Place the pump on a level surface free from any
obstructions or potential hazards. The pump should
be placed close to the water level to ensure maximum
pump performance.
TOTAL HEAD
DISCHARGE HEAD
SUCTION HEAD
WARNING
DO NOT run the pump dry.
Running the pump dry can destroy the pump seals
and will void the warranty. If the pump was running
while dry, stop the engine and allow it to cool
thoroughly before filling the chamber with water.
Pour water into the outlet located on top of the pump
housing. (A) Make sure to fill the pump body to the very
top of the outlet with water. Connect the outlet hose to
the outlet. (See section Connecting the Outlet Hose)
Make sure hose connection is secure. As the engine
starts up, this will start the draw of liquid into the pump.
Located within the pump assembly is the one-way valve.
As you prime the pump housing this one-way flap valve
shuts off the opening to the suction hose. The priming
process is only required when the pump housing is not
full of water.
A
Pump output will be affected by the type, length, and
size of the suction and discharge hoses. The pumping
height, also known as the total head, is the distance
from the water level to the point of discharge. As
this distance increases, pump output decreases. The
discharge capacity is greater than the suction capacity.
Therefore, it is important that the suction head is less
than the discharge head.
The time required to draw water from the source to
the pump (self-priming time) can be decreased by
minimizing the suction head.
B
NOTE
Ensure the drain plug is secure before pump
priming and operation. (B) If not secure the pump
will not hold water and prime correctly.
10
ENGLISH 100166
Operation
Connecting the Inlet Hose
Connecting the Inlet Hose Cont’d.
7. Connect the straight outlet joint to the pump. (G)
8. Hand tighten the joint to the pump. Do not over
tighten.
NOTE
Both the intake and outlet ports are
1 in. (2.5 cm). Please insure the connectors to
the suction and discharge hose are 1 in. (2.5 cm)
threaded.
1. Attach the water filter shield to the water filter. (A)
2. Connect them to the intake hose with a hose clamp.
(B)
3. Tighten the screw on the hose clamp to secure. Do not
overtighten.
A
B
G
NOTE
The once connected to the pump, there may be
some threading left after hand tightening. This is
normal. DO NOT overtighten the pipe joint with any
wrench, tool, or otherwise.
NOTE
4. Slide the pipe joint (C) over the straight outlet joint
(D) and then place the rubber gasket (E) into the
base of the pipe joint.
D
C
E
5. Connect the intake hose to the straight outlet joint
with a hose clamp. (F)
6. Tighten the screw on the hose clamp to secure. Do not
overtighten.
F
11
Telfon tape or other sealers are not needed for a
water tight connection. The rubber gasket should
help to make the connection more water tight.
100166 ENGLISH
Operation
Connecting the Outlet Hose
Connecting the Outlet Hose Cont’d.
NOTE
Both the intake and outlet ports are
1 in. (2.5 cm). Please insure the connectors to
the suction and discharge hose are 1 in. (2.5 cm)
threaded.
5. Connect the 90º outlet joint to the pump. (G)
6. Hand tighten the joint to the pump. Do not over
tighten.
G
1. Slide the pipe joint (A) over the 90º outlet joint (B)
and then place the rubber gasket (C) into the base
of the pipe joint.
A
NOTE
B
C
2. Connect the outlet hose to the 90º outlet joint with
a hose clamp. (D)
3. Tighten the screw on the hose clamp to secure. Do not
overtighten.
The once connected to the pump, there may be
some threading left after hand tightening. This is
normal. DO NOT overtighten the pipe joint with any
wrench, tool, or otherwise.
NOTE
Telfon tape or other sealers are not needed for a
water tight connection. The rubber gasket should
help to make the connection more water tight.
D
4. Prime the pump. (E) See priming the pump section>
E
12
ENGLISH 100166
Operation
Starting the Engine
Starting the Engine Cont’d.
WARNING
WARNING
Before attempting to start the engine, the oil level
must be checked and engine oil added if needed.
1. Make certain the water pump is on a flat, level
surface.
2. Check engine oil level. Add oil if needed. (see add
engine oil section)
3. Check fuel level. Add fuel if needed. (see add fuel
section)
4. Move the choke lever to the “Choke” position. (A)
5. Move the throttle level to the idle position. (B)
DO NOT remove the drain plug while the water pump
is on and running
Loss of pressure and suction will occur. Injury may
also occur.
NOTE
Keep choke lever in “Choke” position for 2 pulls of
the recoil starter. After 2 pulls, move choke lever to
the “Run” position for up to the next 3 pulls of the
recoil starter. Too much choke leads to spark plug
fouling/engine flooding due to the lack of incoming
air. This will cause the engine not to start.
Stopping the Engine
A
There is a stop engine button located next to the air
filter cover, above the throttle level. Simply press the
button and the unit should turn off.
B
6. Push and release the primer bulb 5 times to prime
the carburetor. You should see the bulb start to fill up
with fuel and fuel traveling through the fuel line. (C)
B
C
NOTE
If the engine will not be used for a period of two (2)
weeks or longer, please see the Storage section for
proper engine and fuel storage.
7. Pull the starter cord slowly until resistance is felt and
then pull rapidly.
8. As engine warms up, move the choke lever to “Run”.
9. Move the throttle lever to the desired RPM position.
NOTE
Pump performance can be adjusted using the
throttle. To decrease pump output, slide the throttle
down. To increase it, slide the throttle up.
13
100166 ENGLISH
The owner/operator is responsible for all periodic
maintenance.
WARNING
Never operate a damaged or defective water pump.
WARNING
Improper maintenance will void your warranty.
Maintenance and Storage
Engine Maintenance
To prevent accidental starting, remove and ground spark
plug wire before performing any service.
Oil
Change oil when the engine is warm. Refer to the oil
specification to select the proper grade of oil for your
operating environment.
1. Remove oil fill cap/dipstick to drain and add oil. (A)
DANGER
Always disconnect the spark plug wire during times
of inactivity, cleaning and maintenance. This will
prevent any accidental start up that may cause
damage or injury.
A
NOTE
Maintenance, replacement, or repair of emission
control devices and systems may be performed
by any non-road engine repair establishment or
individual.
Complete all scheduled maintenance in a timely manner.
Correct any issue before operating the water pump.
2. Tip the pump on its side to drain all oil into an
approved container.
3. Using a funnel (not included) add up to 2.4 ounces
(70 mL) of oil and replace oil fill cap/dipstick.
4. It is recommended to only fill to the base of the oil fill
hole. DO NOT OVERFILL. (B)
NOTE
For service or parts assistance, contact our help
line at 1-877-338-0999.
B
5. Replace the oil fill cap/dipstick.
6. Dispose of used oil at an approved waste
management facility.
NOTE
Once oil has been added, a visual check should show
oil about 1-2 threads from running out of the fill hole.
If using the dipstick to check oil level, DO NOT screw
in the dipstick while checking.
14
ENGLISH 100166
Maintenance and Storage
Spark Plug
Air Filter
1. Locate and remove the spark plug cable from the top
of the spark plug. (A)
1. Unscrew the air filter wing nut to remove the air filter
cover. (A)
A
A
2. Use the spark plug tool that is in the tool kit to
remove the spark plug.
3. Inspect the electrode on the plug. It must be clean and
not worn to produce the spark required for ignition.
4. Make certain the spark plug gap is 0.6 - 0.8 mm or
(0.024 - 0.031 in.).
0.6 - 0.8 mm
0.024 - 0.031 in.
A
2. Remove the foam element.
3. Wash in liquid detergent and water. Squeeze
thoroughly dry in a clean cloth.
4. Saturate in clean engine oil.
5. Squeeze in a clean, absorbent cloth to remove all
excess oil.
6. Reassemble the element.
7. Reattach the air filter cover and tighten wing nut.
Cleaning
CAUTION
5. Refer to spark plug section on specifications page.
6. Carefully thread the plug into the engine for
replacement spark plug. (if needed)
7. Use the spark plug tool to firmly re-install the plug.
8. Re-attach the spark plug wire to the plug.
DO NOT spray the engine or muffler directly with
water. Water may cause unsuspected damage.
Use a damp cloth to clean exterior surfaces of the
engine and pump.
Use a soft bristle brush to remove dirt and oil, if
needed.
Use an air compressor (25 PSI) to clear dirt and debris
from the engine, muffler and pump.
Adjustments
The air-fuel mixture is not adjustable. Tampering with
the governor can damage your water pump and will void
your warranty. CPE recommends that you contact our
service line at
1-877-338-0999 for all other service and/or adjustment
needs.
15
100166 ENGLISH
Maintenance and Storage
Maintenance Schedule
Storage
Follow the service intervals indicated in the following
maintenance schedule.
Service your water pump more frequently when
operating in adverse conditions.
Contact our help line at 1-877-338-0999 to locate the
nearest Champion Power Equipment certified service dealer
for your water pump or engine maintenance needs.
For longer term storage, please follow these guidelines.
Engine Storage
Clean air filter
1. Allow the engine to cool completely before storage.
2. Clean the engine according to the instructions in the
Maintenance section.
3. Drain all fuel completely from the fuel line and
carburetor to prevent gum from forming.
4. Add a fuel stabilizer into the fuel tank.
5. Change the oil.
6. Remove the spark plug and pour about ½ ounce
(14.8 ml) of oil into the cylinder. Crank the engine
slowly to distribute the oil and lubricate the cylinder.
7. Reattach the spark plug.
Change oil if operating under heavy load or in hot
environments
Water pump Storage
Every Time Before Start Up
Check oil level
Clean around air intake and muffler
First 5 Hours
Change oil - if has not been performed yet
Every 50 hours or every season
Every 100 hours or every season
Change oil
Clean/Adjust spark plug
Check/Adjust valve clearance*
Clean spark arrester
Clean fuel tank and filter*
Every 250 hours
Clean combustion chamber
Every 3 years
Replace fuel line
*To be performed by knowledgeable, experienced owners or
Champion Power Equipment certified dealers.
1. Allow the water pump to cool completely before
storage.
2. Turn off the fuel supply at the fuel valve.
3. Drain the pump chamber thoroughly.
4. Clean the water pump according to the instructions
in the Maintenance section.
5. Once the pump is dry, spray WD-40 or similar
product into the pump housing through all ports and
drainage hole.
6. Store in a clean, dry place out of direct sunlight.
DANGER
Engine exhaust contains odorless and colorless
carbon monoxide gas.
To avoid accidental or unintended ignition of your
product during periods of storage, the following
precautions should be followed:
–– When storing the unit for short or extended
periods of time make sure that the spark plug
wire is disconnected.
16
Maintenance and Storage
Winter Storage
Protect your water pump parts from freezing.
1. Apply all storage instructions from previous sections.
2. Make sure water pump hose is free of all water
before storing for winter.
3. In order to prevent the pump from freezing you will
need to insert RV antifreeze.
4. You will need approximately 6 ounces (177.4 ml) of
RV Antifreeze, a funnel, and approximately 12 in.
(30.5 cm) of garden hose or equivalent. See diagram
below.
5. Pour the antifreeze into the funnel, then pull on the
engine recoil starter to create suction in the pump
housing. Pull the recoil several times until antifreeze
comes out of the pump outlet. DO NOT START THE
ENGINE WHEN DO THIS. Only pull the recoil cord
if the fuel valve and engine switch are in the OFF
position.
17
ENGLISH 100166
100166 ENGLISH
Specifications
Engine Specifications
Spark Plugs
––
––
––
––
OEM spark plug: NHSP CMR5H
Make certain the spark plug gap is 0.6 - 0.8 mm or
(0.024 - 0.031 in.).
Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S35
Displacement. . . . . . . . . . . . . . . . . . . . . . . . 31cc
Type. . . . . . . . . . . . . . . . . . . . . . . . 4-Stroke OHV
Start Type . . . . . . . . . . . . . . . . . . . . . . . . . Recoil
Water Pump Specifications
––
––
––
––
––
––
––
––
––
––
––
––
Model. . . . . . . . . . . . . . . . . . . . . . . . . . . 100166
Inlet Diameter. . . . . . . . . . . . . . 1 in. (2.5 cm) NPT
Outlet Diameter . . . . . . . . . . . . 1 in. (2.5 cm) NPT
Fuel Capacity. . . . . . . . . . . . . 0.145 gal. (550 mL)
Total Head. . . . . . . . . . . . . . . . . . . . 95 ft. (29 m)
Suction Head. . . . . . . . . . . . . . . . . . . 16 ft. (5 m)
Max Delivery Volume. . . . . . 30 Gal/min (114 L/min)
Gross Weight . . . . . . . . . . . . . . . . . 24.3 lb. (11 kg)
Net Weight. . . . . . . . . . . . . . . . . . 20.9 lb. (9.5 kg)
Height. . . . . . . . . . . . . . . . . . . . 13.6 in. (35.4 cm)
Width . . . . . . . . . . . . . . . . . . . . . 9.7 in. (24.6 cm)
Length. . . . . . . . . . . . . . . . . . . 12.8 in. (32.4 cm)
Fuel
Fuel capacity is 0.145 gal. (550 mL). Use regular
unleaded gasoline with a minimum octane rating of 85
and an ethanol content of no more than 10% by volume.
Maintenance Valve Clearance
–– Intake: 0.05 – 0.08 mm (0.002 – 0.003 in.)
–– Exhaust: 0.08 – 0.12 mm (0.003 – 0.005 in.)
Note: Tech bulletin regarding the valve adjustment
procedure is on www.championpowerequipment.com.
An Important Message About Temperature
Your Champion Power Equipment product is designed
and rated for continuous operation at ambient
temperatures up to 40°C (104°F). When your product is
needed your product may be operated at temperatures
ranging from -15°C (5°F) to 50°C (122°F) for short
periods. If the product is exposed to temperatures
outside this range during storage, it should be brought
back within this range before operation. In any event,
the product must always be operated outdoors, in a
well-ventilated area and away from doors, windows and
other vents.
Oil
Use 10W-30 automotive oil.
Oil capacity is up to 2.4 ounces (70 mL).
DO NOT OVERFILL.
Please reference the following chart for recommended
oil types for use in the water pump.
Degrees Celsiusº (Outside)
Full Synthetic 5W-30
Degrees Fahrenheitº (Outside)
NOTE
Weather will affect engine oil and engine
performance. Change the type of engine oil used
based on weather conditions to suit the engine
needs.
18
Specifications
Parts Diagram
19
ENGLISH 100166
100166 ENGLISH
Parts List
#
Part Number
Description
1
1ZC7SW001
Engine
Qty
1
2
100022034
Connecting Flange
1
3
100011264-0003
Bolt, M6 x 16
4
100022357-0001
Handle Assembly
1
5
100032475
Handle Glue Cover
1
6
100032474
Handle
1
7
100011428-0001
Nut, M12 x 1.25
1
8
100021995
Side Cover
1
9
100022260
Sealing Ring,Pump
1
10
100010538
Flat Washer, ø5 x 0.6 x ø9
4
11
100010833-0001
Bolt, M5 x 25
4
12
100021960
Mechanical Seal
1
13
100022062
Impeller
1
10
14
100022096
Volute Cover
1
15
100022145
Gasket, Inlet
1
16
100022230
Clamp, Inlet/Outlet
3
17
100022131
Outlet Joint
1
18
100022184
Pipe Joint
2
19
100022198
Gasket, Inlet/Outlet
2
20
100021936
Pump Body Component
1
21
100022026
Pump Body
1
22
100021968
Gasket, Plug
1
23
100021947
Plug
1
24
100022159
Inlet Joint
1
25
100022237
Water Filter
1
26
100022244
Shield, Water Filter
1
27
100022327-0002
Support Block, Engine
1
28
100010831-0001
Bolt, M5 x 10
2
29
100011135-0001
Nut, M6
4
30
100022348-0002
Frame Base
1
31
100011261-0004
Bolt, M6 x 12
1
32
100022334
Vibration Mount
4
33
100010835-0001
Bolt, M6 x 10
4
34
100011229-0001
Bolt, M8 x 12
2
35
100000104
Tool
1
36
100050140
Intake Hose 5m
1
37
100050139
Discharge Hose 8m
1
20
Specifications
Engine Parts Diagram
21
ENGLISH 100166
100166 ENGLISH
Engine Parts List
#
Part Number
Description
Qty
#
Part Number
Description
1
100002804
Breather Hose
1
54
100010135
Gasket, Crankcase
2
100010417-0001
Screw, M5 × 15
12
55
100010668
Bearing, 6002
3
100002301
Valve Cover
1
56
100002919
Crankcase Cover
4
100002788
Oil Block
1
57
100004096-0001
Dipstick Assembly
5
100011001-0001
Self-tappling Screw, ST4.2 ×
10
1
58
100030067
O-Ring, ø16 × 3
6
100010128
Gasket, Valve Cover
59
100004177-0001
Dipstick
7
100004387
Push Rod
60
100010419-0001
Screw, M5 × 28
8
100004416
Rocker Arm Assembly
61
100017615
Oil Seal, ø15 × ø26 × 5
9
100004487
Lock Nut
62
100010911-0003
Washer, ø8
10
100030648
Adjust Nut
63
100007541
Starter Cup
11
100004463
Upper Rocker Arm
64
100007180-0004
Recoil Starter Assembly
12
100004481
Pin
65
100010946-0002
Screw, M4 × 10
13
100005549
Gasket, Carburetor Insulator
66
100010908-0001
Washer, ø4.3
14
100011146-0001
Bolt, M5 × 55
15
100005582
Insulator
16
100010418-0001
Screw, M5 × 20
17
100030031
Gasket, Carburetor Insulator
18
100005165
Carburetor
19
100005663
O-Ring
20
100004626
Air Filter Assembly
21
100004963
Air Filter Base
22
100004804
Air Filter Element
23
100004822
Air Filter Cover
24
100004957
Bolt
25
100011451-0002
Nut, M5
26
100009185
Ignition Module
27
100011528-0003
Bolt, M6 × 10
28
100010539
Washer, ø6 × 1 × ø12
29
100004483
Pin
30
100004464
Lower Rocker Arm
31
100004517
Valve, Intake
32
100004540
Valve, Exhaust
33
100010190
Gasket, Crankcase
34
100010403-0001
Stud, M5 × 30
35
100010542
Pin, ø4 × 8
36
100003218
Circlip
37
100003055
Piston
38
100003112
Piston Pin
39
100003227
Piston Ring Set
40
100030448
Oil Ring
41
100003176
Piston Ring, 2nd
42
100003134
Piston Ring, 1st
43
100002362
Cylinder Head
44
100004560
Valve Spring
45
100004577
Valve Spring Seat
46
100009371
Spark Plug
47
100010383-0001
Stud, M5 × 54
48
100006544
Gasket, Exhaust
49
100006547
Cover, Muffler
50
100010420-0001
Screw, M5 × 10
51
100006155
Muffler
52
100010576
Woodruff Key
53
100003412
Connecting Rod
1
2
2
2
2
2
1
1
2
1
7
1
1
1
1
1
1
1
1
8
1
1
1
1
2
1
1
1
4
4
2
1
1
1
1
1
1
1
2
2
1
2
2
1
1
1
1
1
67
100007431
Guide Plate
68
100007481
Spring
69
100007425
Starter Pawl
70
100007413
Starter Reel
71
100007468
Starter Rope
72
100007723
Starter Spring
73
100007496
Starter Cover
74
100007454
Starter Handle
75
100011002-0002
Self-tappling Screw, M4.2 × 19
76
100007934
Throttle Linkage
77
100009154
Stop Switch
78
100008058
Governor Gear Bracket
Assembly
79
100004273
Camshaft Assembly
80
100004329
Drive Timing Gear
Return Spring
81
100004382
82
100004373
Pressure Release Valve
83
100004352
Camshaft Cover
84
100004350
Camshaft Pin
85
100002590
Crankcase
86
100009480
Flywheel
87
100007069
Flywheel Cover
88
100022346
Connection Shaft
89
100007164-0013
Shroud
90
100008537
Fuel Tank Assembly
91
100008745
Fuel Cap Assembly
92
100008891
Fuel Tank
93
100017667
Fuel Hose, ø2.5 × ø5.3 × 230
94
100017668
Fuel Hose, ø2.5 × ø5.3 × 270
95
100010813
Washer, ø5 × 1.5 × ø15
96
100009032
Float Filter
97
100009031
Float
98
100021457
Plug, Fuel Tank
99
100008927
Damping Pad
Qty
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
3
22
ENGLISH 100166
Troubleshooting
Problem
Cause
Solution
Water pump will not start
No fuel
Add fuel
Faulty spark plug
Replace spark plug
Low oil level
Fill crankcase to the proper level; place
water pump on a flat, level surface
Choke in the wrong position
Adjust choke
Spark plug wire loose
Attach wire to spark plug
Out of fuel
Fill fuel tank
Low oil level
Fill crankcase to the proper level; place
water pump on a flat, level surface
Strainer or hose clogged
Remove debris from strainer or hose
Pump not primed
Re-prime pump
Suction hose out of water
Place suction hose under the surface of
the water
Head limit exceeded
Relocate pump so suction head is less
than discharge head (maximum 98 feet)
Air leak
Tighten connectors and clamps or replace
seal packing, and or apply more telfon
tape as needed.
Water pump will not start; Water pump
starts but runs roughly
Water pump shuts down during operation
Water pump overheating or performing
poorly
For further technical support:
Technical Service
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
tech@championpowerequipment.com
23
100166 ENGLISH
Warranty
WARRANTY
CHAMPION POWER EQUIPMENT
1 YEAR LIMITED WARRANTY
Effective September 1, 2006. Replaces all undated warranties and all
warranties dated before September 1, 2006.
Warranty Qualifications
Champion Power Equipment (CPE) will register this
warranty upon receipt of your Warranty Registration Card
and a copy of your sales receipt from one of CPE’s retail
locations as proof of purchase.
Please submit your warranty registration and your proof
of purchase within ten (10) days of the date of purchase.
Repair/Replacement Warranty
CPE warrants to the original purchaser that the
mechanical and electrical components will be free of
defects in material and workmanship for a period of one
(1) year from the original date of purchase (90 days for
commercial & industrial use). Transportation charges on
product submitted for repair or replacement under this
warranty are the sole responsibility of the purchaser.
This warranty applies only to the original purchaser and
is not transferable.
Do Not Return The Unit To The Place Of Purchase
Contact CPE’s Technical Service and CPE will
troubleshoot any issue via phone or e-mail. If the
problem is not corrected by this method, CPE will, at its
option, authorize evaluation, repair or replacement of the
defective part or component at a CPE Service Center.
CPE will provide you with a case number for warranty
service. Please keep it for future reference. Repairs
or replacements without prior authorization, or at an
unauthorized repair facility, will not be covered by this
warranty.
Warranty Exclusions
This warranty does not cover the following repairs and
equipment:
Normal Wear
Installation, Use and Maintenance Cont’d.
Normal maintenance such as spark plugs, air filters,
adjustments, fuel system cleaning and obstruction due
to buildup is not covered by this warranty.
Other Exclusions
This warranty excludes:
–– Cosmetic defects such as paint, decals, etc.
–– Wear items such as filter elements, o-rings, etc.
–– Accessory parts such as starting batteries, and
storage covers.
–– Failures to due acts of God and other force majeure
events beyond the manufacturer’s control.
–– Problems caused by parts that are not original
Champion Power Equipment parts.
This warranty does not apply to water pumps used for
prime power in place of a utility.
Limits of Implied Warranty and Consequential Damage
Champion Power Equipment disclaims any obligation to
cover any loss of time, use of this product, freight, or
any incidental or consequential claim by anyone from
using this water pump. THIS WARRANTY IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
A unit provided as an exchange will be subject to the
warranty of the original unit. The length of the warranty
governing the exchanged unit will remain calculated by
reference to the purchase date of the original unit.
This warranty gives you certain legal rights which may
change from state to state. Your state may also have
other rights you may be entitled to that are not listed
within this warranty.
Contact Information
Address
Champion Power Equipment, Inc.
Customer Service
12039 Smith Ave.
Santa Fe Springs, CA 90670
www.championpowerequipment.com
Water pumps need periodic parts and service to perform
well. This warranty does not cover repair when normal
use has exhausted the life of a part or the equipment as a
whole.
Customer Service
Installation, Use and Maintenance
Technical Service
This warranty will not apply to parts and/or labor if this
water pump is deemed to have been misused, neglected,
involved in an accident, abused, loaded beyond the water
pump’s limits, modified, installed improperly or connected
incorrectly to any electrical component.
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
Fax no.: 1-562-236-9429
Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)
Toll Free: 1-877-338-0999
tech@championpowerequipment.com
24/7 Tech Support: 1-562-204-1188
24
Champion Power Equipment, Inc. (CPE),
The United States Environment Protection Agency (U.S. EPA.) and the California Air Resources Board (CARB)
Emission Control System Warranty
Your Champion Power Equipment (CPE) engine complies with both the U.S. EPA and state of California Air
Resources Board (CARB) emission regulations.
YOUR WARRANTY RIGHTS AND OBLIGATIONS:
The US EPA, California Air Resources Board, and CPE are pleased to explain the Federal and California Emission
Control Systems Warranty on your 2015 small off-road engine and engine powered equipment. In California, new,
small off-road engines and new equipment that use small off-engines must be designed, built and equipped to meet
the State’s stringent anti smog standards. In the other states, new engines and equipment must be designed, built
and equipped, at the time of sale, to meet U.S. EPA regulations for small non-road engines. CPE warrants the
emission control system on your small off-road engine and equipment for the period of time listed below, provided
there has been no abuse, neglect, unapproved modification, or improper maintenance of your equipment.
Your emission control system may include parts such as the carburetor, fuel-injection system, the ignition system,
catalytic converter and fuel lines. Also included may be hoses, belts, connectors and other emission related
assemblies. Where a warrantable condition exits, CPE will repair your small off-road engine at no cost to you
including diagnosis, parts and labor. For engines less than or equal to 80cc, only the fuel tank and fuel line is
subject to the evaporative emission control warranty requirements of this section.
MANUFACTURER’S EMISSION CONTROL SYSTEM WARRANTY COVERAGE:
This emission control system is warranted for two years, subject to provisions set forth below. If, during the
warranty period, emission related part on your engine is defective in materials or workmanship, the part will be
repaired or replaced by CPE.
OWNER WARRANTY RESPONSIBILITIES:
As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in
your Owner’s Manual. CPE recommends that you retain all your receipts covering maintenance on your small offroad engine, but CPE cannot deny warranty solely for the lack of receipts or for your failure to ensure the
performance of all scheduled maintenance.
As the small off-road engine owner, you should however be aware that CPE may deny you warranty coverage if
your small, off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved
modifications.
You are responsible for presenting your small off-road engine to an Authorized CPE service outlet or alternate
service outlet as described in (3)(f.) below, CPE dealer or CPE, Santa Fe Springs, Ca. as soon as a problem exists.
The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact:
Champion Power Equipment, Inc.
Customer Service
12039 Smith Ave.
Santa Fe Springs, CA 90670
1-877-338-0999
tech@championpowerequipment.com
EMISSION CONTROL SYSTEM WARRANTY
The following are specific provisions relative to your Emission Control System (ECS) Warranty Coverage.
1. APPLICABILITY: This warranty shall apply to 1995 and later model year California small off-road engines (for
other states, 1997 and later model year engines). The ECS Warranty Period shall begin on the date the new engine
or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months
thereafter.
2. GENERAL EMISSIONS WARRANTY COVERAGE
CPE warrants to the original, end-use purchaser of the new engine or equipment and to each subsequent
purchaser that each of its small off-road engines is:
a. Designed, built and equipped so as to conform to U.S. EPA emissions standards for spark-ignited
engines at or below 19 kilowatts and all applicable regulations adopted by the California Air Resources Board
and
b. Free from defects in materials and workmanship that cause the failure of a warranted part to be identical
in all material respects to the part as described in the engine manufacturer’s application for certification for a period
of two years.
3. THE WARRANTY ON EMISSION-RELATED PARTS WILL BE INTERPRETED AS FOLLOWS:
a. Any warranted part that is not scheduled for replacement as required maintenance in the Owners
Manual shall be warranted for the ECS Warranty Period. If any such part fails during the ECS Warranty Period, it
shall be repaired or replaced by CPE according to Subsection “d” below. Any such part repaired or replaced under
the ECS Warranty shall be warranted for any remainder of the ECS Warranty Period.
b. Any warranted, emissions-related part which is scheduled only for regular inspection as specified in the
Owners Manual shall be warranted for the ECS Warranty Period. A statement in such written instructions to the
effect of “repair or replace as necessary”, shall not reduce the ECS Warranty Period. Any such part repaired or
replaced under the ECS Warranty shall be warranted for the remainder of the ECS Warranty Period.
c. Any warranted, emissions-related part which is scheduled for replacement as required maintenance in
the Owner’s Manual shall be warranted for the period of time prior to the first scheduled replacement point for that
part. If the part fails prior to the first scheduled replacement, the part shall be repaired or replaced by CPE
according to Subsection “d” below. Any such emissions-related part repaired or replaced under the ECS Warranty,
shall be warranted for the remainder of the ECS Warranty Period prior to the first scheduled replacement point for
such emissions-related part.
d. Repair or replacement of any warranted, emissions-related part under this ECS Warranty shall be
performed at no charge to the owner at a CPE Authorized Service Outlet.
e. The owner shall not be charged for diagnostic labor which leads to the determination that a part covered
by the ECS Warranty is in fact defective, provided that such diagnostic work is performed at a CPE Authorized
Service Outlet.
f. CPE shall pay for covered emissions warranty repairs at non-authorized service outlets under the
following circumstances:
i. The service is required in a population center with a population over 100,000 according to U.S.
Census 2000 without a CPE Authorized Service Outlet AND
ii. The service is required more than 100 miles from a CPE Authorized Service Outlet. The 100 mile
limitation does not apply in the following states: Alaska, Arizona, Colorado, Hawaii, Idaho, Montana, Nebraska,
Nevada, New Mexico, Oregon, Texas, Utah and Wyoming.
g. CPE shall be liable for damages to other original engine components or approved modifications
proximately caused by a failure under warranty of an emission-related part covered by the ECS Warranty.
h. Throughout the ECS Warranty Period, CPE shall maintain a supply of warranted emission-related parts
sufficient to meet the expected demand for such emission-related parts.
i. Any CPE Authorized and approved emission-related replacement part may be used in the performance of
any ECS Warranty maintenance or repair and will be provided without charge to the owner. Such use shall not
reduce CPE’s warranty obligation.
j. Unapproved add-on or modified parts may not be used to modify or repair a CPE engine. Such use voids
this ECS Warranty and shall be sufficient grounds for disallowing an ECS Warranty claim. CPE shall not be liable
hereunder for failures of any warranted parts of a CPE engine caused by the use of such an unapproved add-on or
modified part.
EMISSION-RELATED PARTS INCLUDE THE FOLLOWING: (using those portions of the list applicable to the
engine)
Systems covered by this
warranty
Fuel Metering System
Fuel regulator, Carburetor and internal parts
Air Induction System
Air cleaner, Intake manifold
Ignition System
Spark plug and parts, Magneto ignition system
Exhaust System
Exhaust manifold, catalytic converter
Miscellaneous Parts
Tubing, Fittings, Seals, Gaskets, and Clamps associated with these listed
systems.
Fuel Tank, Fuel Cap, Fuel Line, Fuel Line Fittings, Clamps, Pressure
Relief Valves, Control Valves, Control Solenoids, Electronic Controls,
Vacuum Control Diaphragms, Control Cables, Control Linkages, Purge
Valves, Vapor Hoses, Liquid/Vapor Separator, Carbon Canister, Canister
Mounting Brackets, Carburetor Purge Port Connector
Evaporative Emissions
Parts Description
TO OBTAIN WARRANTY SERVICE:
You must take your CPE engine or the product on which it is installed, along with your warranty registration card or
other proof of original purchase date, at your expense, to any Champion Power Equipment dealer who is
authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business
hours. Alternate service locations defined in Section (3)(f.) above must be approved by CPE prior to service. Claims
for repair or adjustment found to be caused solely by defects in material or workmanship will not be denied because
the engine was not properly maintained and used.
If you have any questions regarding your warranty rights and responsibilities, or to obtain warranty
service, please write or call Customer Service at Champion Power Equipment, Inc.
Champion Power Equipment, Inc.
12039 Smith Ave.
Santa Fe Springs, CA 90670
1-877-338-0999
Attn.: Customer Service
tech@championpowerequipment.com