American Standard | 4505SSF | Installation guide | American Standard 4505SSF Installation Guide

Installation
Instructions
4505 Series
SYMPHONY
SINGLE CONTROL
KITCHEN PULL-DOWN FAUCET
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
M965053
RECOMMENDED TOOLS
Phillips Screwdriver
Regular Screwdriver
1
Adjustable Wrench
Plumbers' Putty or Caulking
CAUTION
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
Turn off water at
main supply.
Make certain the SEAL (9) is properly seated in recess of spout base.
(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Insert SUPPLY HOSES (2), SPRAY HOSE (9) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and
mounting surface. Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1). Discard ESCUTCHEON with PUTTY PLATE (1). Insert supply HOSES (2), SPRAY
HOSE (9) and SHANK (3) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.
Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6).
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
B
A
B
7
SPOUT BASE
9
7
SPOUT BASE
1
9
3
2
2
3
9
4
5
6
PUTTY
SINK OR
MOUNTING
S U R FA C E
9
4
5
8
6
8
2
MAKE WATER SUPPLY CONNECTIONS
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply (Marked with a Red Stripe) to Hot
and right supply (Marked with Blue Stripe) to
Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten.
2
1
Faucet supplies are 21" long from faucet base.
COLD
Note: If additional supply length is
required, installer must purchase
additional parts separately.
HOT
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
3
INSTALL WEIGHT
With HAND SPRAY (1) seated in SPOUT (2),
install WEIGHT (4) onto HOSE (3)
using two SCREWS (5). Locate the WEIGHT (4)
16 inches from the underside of the sink deck.
Tighten SCREWS (5) firmly.
2
1
16"
4
5
3
4
CHECK CONNECTIONS FOR LEAKS.
Move HANDLE down into "off" position.
Turn on water supplies and check connections for leaks.
Operate HANDLE (2) up and down, left and right to flush
water lines thoroughly.
Operate HAND SPRAY and check connections for leaks.
CHECK CONNECTIONS
FOR LEAKS
M965053
5
TEST INSTALLED FAUCET
SPRAY OPERATION
Move HANDLE (1) into "off"
position.
With FAUCET on press TOGGLE BUTTON (4)
on SPRAY (3) to switch from stream to spray.
Turn on water supplies.
Press and hold PAUSE BUTTON (5) to temporarily
stop flow from SPRAY (3). Release PAUSE
BUTTON (5) to resume flow fromSPRAY (3).
Check connections for leaks.
(See Section 4)
With HANDLE (1) in "off" position,
unthread SPRAY (3) from HOSE (2).
2
Operate handle back to front,
in COLD and HOT positions, to
flush water lines thoroughly.
3
Replace SPRAY (3) onto
HOSE (2).
1
REMOVE
5
3
STREAM (AERATOR)
4
SPRAY
6
SERVICE
If faucet drips, operate HANDLE several times from "off" to "on." Do not
apply excessive force.
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
Unthread the ESCUTCHEON CAP (4). Unthread three MOUNTING SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8).
Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
Place SEALS (8) into CARTRIDGE PORTS (6a).
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING SCREWS (5) alternately.
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE SCREW (1) and install INDEX BUTTON (2).
7
8
6a
1
2
3
6
7
5
4
CARE:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
M965053
Download PDF

advertising