Panasonic TX32LXD55F User manual

Panasonic TX32LXD55F User manual
MODE
OK
1
2
3
4
5
6
7
8
9
C
0
N
PULL
IDTV
Operating Instructions
Digital Progressive LCD TV
Model No.
TX-32LXD55F
The image shown is for illustration only.
This set is only for use in Germany.
Please read these instructions before operating your set and retain them for future reference.
English
TQB0E0227U
Dear Panasonic Customer,
We hope that you have many years of enjoyment from your new TV. The Quick Start Guide section at the beginning of
this instruction book will allow you to use the TV as quickly as possible. We recommend that you then read the complete
instruction book, and keep it to refer to as you explore the range of advanced features that this LCD TV offers.
Analogue and Digital television – what are they?
Analogue transmission is the system that has been used for many years for broadcasting television programmes. With continuous
improvements in technology it is now possible to transmit programmes in a digital format, allowing clearer pictures, more stations
and other services to be displayed on screen. Digital television is provided in three different ways; it can be sent along a cable
connection direct to your house, broadcast from a satellite, or broadcast using traditional land based (terrestrial) transmitters.
The first two options require you to have an extra “set top box” decoder and in the case of satellite, a receiving dish mounted
outdoors. While allowing you to receive traditional analogue transmissions in the usual way, this television can also receive
terrestrial digital services using an integrated
(Digital Video Broadcasting) decoder. This allows you to enjoy the new era
of digital terrestrial television without the need for a “set top box” or satellite dish – an adequate roof or loft mounted antenna
is all you need.
Contents
Accessories ................................................................ 2
Warnings and Precautions ......................................... 3
Fitting remote control batteries ................................... 3
Cable cover removal and fitting .................................. 4
How to open the front cover ....................................... 4
How to use the LCD stand ......................................... 4
Quick Start Guide ....................................................... 5
Basic controls: front panel and remote control ........... 7
Using the On Screen Displays ................................... 8
Picture menu .............................................................. 9
Sound menu ............................................................. 10
Setup menu .............................................................. 11
Tuning menu – overview .......................................... 12
Tuning menu – Programme edit ............................... 13
Adding / deleting a programme channel ................ 13
Moving a programme channel ............................... 13
Tuning a programme channel................................ 13
Renaming a programme channel .......................... 14
Locking a programme channel .............................. 14
Copying programme information to
a recording device ........................................ 14
Tuning menu – Auto setup ........................................ 15
Tuning menu – Manual tuning .................................. 16
Manual tuning (via front panel) ................................. 16
DVB Setup Menu – overview ................................... 17
Profile Edit ................................................................ 18
DVB Tuning Menu .................................................... 19
DVB Tuning Menu – DVB Auto Setup ...................... 20
DVB System Setup ................................................... 21
Common Interface Module ....................................... 22
DVB System Update ................................................ 23
Information banner ................................................... 25
Q-Link ....................................................................... 26
Aspect Controls ........................................................ 27
VCR / DVD operation ............................................... 29
Teletext operation ..................................................... 30
Still ............................................................................ 32
Connections ............................................................. 33
How to connect the Headphones / AV3 terminals . 33
How to connect the Audio Output terminals .......... 34
How to connect the AV1 / 2 / 4 Scart terminals ..... 34
How to connect the Component Input terminals ... 34
How to connect the HDMI Input terminal ............... 35
Troubleshooting ........................................................ 36
DVB Troubleshooting ............................................... 37
Maintenance ............................................................. 37
Input signal that can be displayed ............................ 38
Scart and S-video terminal information .................... 38
Specifications ........................................................... 39
Accessories
Check that you have the accessories and items shown
Operating
Instructions
Remote Control
Transmitter
(EUR7651100)
MODE
OK
1
2
3
4
5
6
7
8
9
C
0
N
IDTV
2
Batteries for the
Remote Control
Transmitter
(2 × R6 (UM3) size)
Clamper
Pan European
Guarantee Card
Warnings and Precautions
• This TV set is designed to operate on AC 220-240 V,
50 / 60 Hz.
• To prevent damage which might result in electric shock
or fire, do not expose this TV set to rain or excessive
moisture. This TV must not be exposed to dripping or
splashing water and objects filled with liquid, such as
vases, must not be placed on top of or above the TV.
• Keep unneeded small parts and other objects out
of the reach of small children. These objects can
be accidentally swallowed. Also, be careful about
packaging materials and plastic sheets.
• WARNING: HIGH VOLTAGE!!!
Do not remove the rear cover as live parts are
accessible when it is removed. There are no user
serviceable parts inside.
Ensure that the mains plug is easily accessible.
• TV Games / Home Computers
Extended use of TV games or home computers with
any television set can cause a ‘shadow’ on the screen.
This type of LCD panel phenomenon, can be limited
by observing the following points:
• The On / Off switch on this model does not fully
disconnect the TV from the mains supply. Remove the
mains plug from the wall socket before connecting or
disconnecting any leads, or if the TV set is not used
for a prolonged period of time.
Note:
If the set is not switched off when the TV station stops
transmitting, it will automatically go to Standby mode
after 30 minutes. This function will not operate when
the TV is in AV mode.
• Cabinet and LCD panel care
Remove the mains plug from the wall socket. The
cabinet and LCD panel can be cleaned with a soft cloth
moistened with mild detergent and water. Do not use
solutions containing benzol or petroleum.
• When ambient temperature is cool, the picture may
take a short time to reach normal brightness, but this
is not a malfunction. (After brief moment, the picture
will have normal brightness.)
• Adequate ventilation is essential to prevent failure of
electrical components, we recommend that a gap of
at least 10 cm is left all around this television receiver
even when it is placed inside a cabinet or between
shelves.
• Avoid exposing the TV set to direct sunlight and other
sources of heat. To prevent fire, never place any type
of candle or naked flame on top or near the TV set.
• Ventilation should not be impleded by covering the
ventilation openings with items such as newspapers,
tablecloths and curtains.
• Reduce the brightness and contrast levels to a minimum
viewing level.
• Do not allow a still picture to be displayed for an extended
period, as this can cause an after-image to remain on the
LCD TV screen.
• Examples of still pictures include logos, video games,
computer images, teletext and images displayed in 4:3
mode.
• This type of LCD panel damage, is not an operating defect,
and as such is not covered by the Panasonic warranty.
Fitting remote control batteries
1
2
3
+
-
+
-
“R6 (UM3)” size
Pull and hold the hook, then
open the battery cover.
•
•
•
•
Insert batteries - note correct
polarity ( + and -).
Replace the cover.
Make sure that the batteries are fitted the correct way round.
Do not mix old batteries with new batteries. Remove old, exhausted batteries immediately.
Do not mix different battery types, i.e. Alkaline and Manganese.
Do not use rechargeable (Ni-Cad) batteries.
3
Cable cover removal and fitting
Removal
1. Push down hooks and pull the cover slightly towards
yourself to disengage the claws (at 3 points).
2. Slowly pull out in the downward direction.
Fitting
1. Insert the claws (at 3 points) at the bottom end.
2. Push until it clicks.
Note:
To avoid interference appearing on the screen, do not bundle the RF cable and mains lead together.
How to open the front cover
PULL
PULL
Raise the lower part of the door
marked “PULL”.
How to use the LCD stand
Adjust the LCD panel to your desired angle.
The LCD panel can be adjusted the following direction:
20° Right
20° Left
(View from the top)
4
Quick Start Guide
1
Connection and setting up options
Please ensure that the unit is disconnected from the mains
before attaching or disconnecting any leads.
RF cable
(Not supplied)
SET TOP BOX
AV1
AV2
AV4
COMPONENT
L
Y
R
AUDIO
Scart cables
(Not supplied)
PB
RGB
VIDEO
VIDEO
S-VIDEO
RGB
VIDEO
S-VIDEO
PR
VIDEO
RF cable (Not supplied)
VCR / DVD
Recorder
OR
Plug in aerial and connect ancillary equipment.
2
Connect the mains plug to the wall socket.
MODE
Press the [
set on.
] switch on the TV set to turn the
OK
To switch the TV set to Standby mode, press the
button on the remote control.
The TV set can be switched on by pressing the
button again if it was in Standby mode.
PULL
Note:
This TV will still consume some power as long
as the mains plug is still inserted into the wall
socket.
2
3
4
5
6
7
8
9
C
0
N
IDTV
Remote control signal sensor
C.A.T.S. sensor
LCD C.A.T.S. (Contrast Automatic Tracking
System) automatically senses the ambient
light conditions and adjusts the brightness and
gradation accordingly, to optimize contrast.
C.A.T.S. is in effect when Viewing mode is set
to Auto. See page 9.
1
Power Indicator
Standby : Red
On : No Light
DVB Indicator
DVB system active during
Direct TV Recording (Standby) : Orange (flash)
Tuner Lock On (Standby) : Orange
Otherwise : No Light
5
Quick Start Guide
3
Auto setup will begin.
The TV will search for DVB stations and Analogue stations:
TV stations will be located, sorted into order and stored ready for use.
Stations are sorted into the following order:
• DVB Stations: Are sorted into channel order, but can be made favourites
list by Profile Edit. See page 18.
• Analogue Stations: Are sorted into channel order, but can be changed to
your preference. See page 13.
DVB Auto Setup
Please Wait !
5
Prog. Channel
69
Service Name
NetID.
TS ID. Quality
4
34 VOX
12302
4158
9
5
54 N24
12302
4158
9
6
54 ProSieben
12302
4158
9
7
54 KABEL1
12302
4158
9
8
54 SAT.1
12302
4158
9
This will take about 3 mins.
Exit
CH12
AUTO SETUP IN PROGRESS
SEARCHING :
PLEASE WAIT
02
78:01
41
Exit
4
TV to VCR or DVD Recorder Download
If a “Q-Link”, “NEXTVIEWLINK” or compatible recording device has been
connected to a Scart terminal (AV2 or AV4) before starting Step 2, programme
information will be downloaded to that device.
DOWNLOAD IN PROGRESS
PLEASE WAIT
Programme : 63
Remote control unavailable
Only the analogue programme positions will be downloaded to the recording device, in the same order as
stored in the TV. See page 26.
Not all VCRs / DVD Recorders support this download of programme information, some may require to be
started manually.
Refer to the recording device’s operating instruction book.
If a recording device other than those described above has been connected, then there will be no download operation.
Notes:
• If the recording device has not accepted download data from the TV, you may need to select the Download
option from the device’s menu system. Refer to the recording device’s operating instruction book.
• If Q-Link is not operating correctly, check the following:
The Scart cable is connected to the TV’s Scart terminal, AV2 or AV4, and correctly setup in the menu.
The Scart cable is connected to the recording device’s compatible (Q-Link, NEXTVIEWLINK or similar
technology) Scart terminal.
The Scart cable is a “fully wired” type.
• For further information on Q-Link and connecting equipment, see page 26, 34, 38.
5
DVB
Analogue
MODE
Press the MODE button to select the mode you want to view.
MODE
GUIDE
Press the GUIDE button.
OK
Analogue mode: Analogue Programme Guide
Use the cursor buttons to move the cursor bar.
Use the programme change button to step through the guide page by page.
To view the selected programme, move the cursor to the programme and
then press the OK button.
1
2
3
4
5
6
7
8
9
C
0
OK
EXIT
The guide can be cleared from the screen using the EXIT button.
N
DVB mode: Information banner
Press the Blue button to scroll through available categories.
Blue
IDTV
Press the up or down cursor button to step through the available
programmes.
Press the OK button to view a programme.
OK
Analogue mode
Analogue Programme Guide
Prog.
VCR
1
2
3
4
5
6
7
8
9
10
11
12
6
:
:
:
:
:
:
:
:
:
:
:
:
:
Name
Chan.
CH21
Das Erste CH44
ZDF
CH51
RTL
CH41
CH47
CH23
CH26
CH58
-
Prog.
13
14
15
16
17
18
19
20
21
22
23
24
:
:
:
:
:
:
:
:
:
:
:
:
Name
Chan.
-
DVB mode
1 Das Erste
Lotti auf der Flucht
20:00 - 20:55
20:30
For info press
ger
All Services
Multi Audio
Profile
Now
Basic controls: front panel and remote control
On / Off switch
STR (Normalization store)
Used to store tuning and other function settings.
F (Function select)
Displays the On Screen Display functions, use
repeatedly to select from the available functions Volume, Contrast, Brightness, Colour, Sharpness,
Tint (in NTSC mode), Bass, Treble, Balance and
Tuning mode (Analogue mode only).
Headphones jack
AV3 terminals
(see page 33)
(see page 33)
TV/AV button (see page 33)
Increases or decreases the programme position by one. When a
function is already displayed, press to increase or decrease the
selected function. When in Standby mode, switches TV On.
Standby On / Off button
Switches TV On or Off (Standby mode).
GUIDE button
Analogue mode:
Displays the Programme table.
Move the cursor to choose the position,
then press the OK button to the viewing
screen.
DVB mode:
Press to display status information for the
current Programme position.
MODE button (see page 8)
Switch between viewing DVB and
Analogue modes.
DVB DIRECT
Analogue TV REC
MODE
GUIDE
TV/AV
DIRECT TV Record button
(see page 26)
Switch between viewing TV or AV input.
(see page 33)
OK
EXIT
MENU
Cursor buttons to make selections and
adjustments.
Press to confirm selections and choices.
Exit the mode.
Menu button
Press to access the Picture, Sound and
Setup menus. (see page 8-11)
Coloured buttons used for the selection,
navigation and operation of various
functions.
Teletext button (see page 30-32)
Text F.P. button (see page 31)
Direct channel access
Available in Analogue mode.
During normal TV viewing or when
in the Tuning, Programme edit or
Manual tuning menus, press and then
enter channel number using the numeric
buttons.
Press twice to change to the Cableband
mode.
Programme up / down button
TEXT
F.P.
INDEX HOLD
1
2
3
4
5
6
7
8
9
0
C
Text Hold / Picture Still button
(see page 30, 32)
Text Index button (see page 32)
Programme / channel change buttons (09) and Teletext page buttons.
(see page 30-32)
When in Standby mode, switches TV
On.
VCR
Information button (see page 25)
Volume up / down button
ASPECT
N
REC
PROGRAMME
VCR
DVD
Sound mute On / Off
VCR / DVD buttons
(see page 29)
ASPECT control button
(see page 27, 28)
N (Normalize) button
Resets all settings to their default levels.
IDTV
7
Using the On Screen Displays
Many features available on this TV can be accessed via the On Screen Display menu system. Use the remote control
as shown below to access and adjust features as desired.
Press the MODE button to select DVB or Analogue
mode.
The MENU button is used to open the main menus and also
to return to the previous menu.
DVB
Analogue
MODE
The left and right cursor buttons are used to access menus,
adjust levels or to select from a range of options.
The EXIT button is used to exit the menu system and return
to the normal viewing screen.
An On Screen Help box is displayed whenever a menu is
displayed on the TV. This Help box indicates which buttons on
the remote control are used to navigate the menu shown, see
above for descriptions of button functions.
Note:
The Help box is not shown in the menu pictures in this instruction
book due to space limitations.
8
OK
MENU
The up and down cursor buttons are used to move the
cursor and select menus.
The OK button is used with a number of features to store
settings after adjustments have been made or options have
been set.
MODE
1
2
3
4
5
6
7
8
9
C
0
N
OK
IDTV
EXIT
Sound menu
Bass
Treble
Balance
Headphone volume
MPX
Mode
Ambience
No service
Music
Off
Select
Adjust
Exit
Return
ON SCREEN HELP
‘Instructions’ box
Picture menu
Press the MENU button.
MENU
MODE
Move to choose Picture menu.
OK
Access Picture menu.
Move to choose menu option.
Adjust chosen option or access chosen menu.
Press the EXIT button at any time to go back to watching TV.
1
2
3
4
5
6
7
8
9
C
0
N
EXIT
IDTV
Viewing mode
The Viewing mode menu allows you to select four different
screen settings - Dynamic, Normal, Cinema and Auto.
In each Viewing mode setting, Contrast, Brightness,
Colour, Sharpness, Tint (in NTSC only), Colour balance,
Colour management, P-NR, MPEG NR and 3D-COMB
can be adjusted and stored to suit your particular viewing
requirement. (e.g., you may require different settings for
viewing sports, films, news etc.)
Viewing mode offers you up to a maximum of four separate
settings for each signal source: RF, AV1, AV2, AV3, AV4,
Component and HDMI. Changes will be stored automatically.
By analysing and processing the incoming picture, all four
modes feature automatic enhancement.
Contrast, Brightness, Colour, Sharpness
Increase or decrease the levels of these options according
to your personal preference.
Tint
Colour balance
With an NTSC signal source connected to the TV, the picture
hue can be adjusted to suit your taste.
Allows you to set the overall colour tone of the picture.
Choose from Cool, Normal and Warm.
Colour
management
Enables vivid colour adjustment automatically.
P-NR
Automatically reduces unwanted picture noise.
Not available during HDMI and HD signal input.
MPEG NR
3D-COMB
Reduces MPEG noise.
Allows you to choose from Off, Min, Mid and Max.
This function is effective in reducing the digital block noise
when viewing DVD, VCD or digital broadcasting. The effect
will be changed based on the scene and image.
MPEG: Compression technology of the image signal
adopted by DVD, VCD or digital broadcasting.
Main menu
P i c t u r e menu
Sound menu
Setup menu
Picture menu
Viewing mode
Contrast
Brightness
Colour
Sharpness
Tint
Colour balance
Colour management
P-NR
MPEG NR
3D-COMB
Dynamic
Normal
On
Auto
Off
On
Picture menu
Viewing mode
Contrast
Brightness
Colour
Sharpness
Tint
Colour balance
Colour management
P-NR
MPEG NR
3D-COMB
Dynamic
Normal
On
Auto
Off
On
Picture menu
Viewing mode
Contrast
Brightness
Colour
Sharpness
Tint
Colour balance
Colour management
P-NR
MPEG NR
3D-COMB
Dynamic
Normal
On
Auto
Off
On
Not available in DVB mode.
Occasionally, whilst viewing still or slow moving pictures,
colour patterning may be seen. Set 3D-COMB to On to
display sharper and more accurate colours.
Displayed only when receiving PAL or NTSC signals.
Not displayed during RGB Video, S-Video, Component and
HDMI input mode.
9
Sound menu
Press the MENU button.
MENU
MODE
Move to choose Sound menu.
OK
Access Sound menu.
Move to choose menu option.
Adjust chosen option or access chosen menu.
Press the EXIT button at any time to go back to watching TV.
1
2
3
4
5
6
7
8
9
C
0
N
EXIT
IDTV
Bass
Increase or decrease level to enhance or minimise lower,
deeper sound output.
Main menu
P i c t u r e menu
Treble
Increase or decrease level to enhance or minimise sharper,
higher sound output.
Sound menu
Balance
Headphone
volume
The levels of sound between the left and right speakers can
be adjusted to suit your listening position.
Can be adjusted independently of the TV speakers so
that everyone can enjoy listening at a level comfortable
for them.
Setup menu
Sound menu
Bass
Treble
Balance
Headphone volume
MPX
Mode
Ambience
HDMI input
No service
Music
Off
Auto
Sound menu
MPX
Not available in DVB mode.
Usually set to Stereo to provide the best reproduction, but if
reception deteriorates or if the service is not available then
switch to Mono. Mono (M1) and (M2) can also be selected
if a mono signal is being transmitted.
Bass
Treble
Balance
Headphone volume
MPX
Mode
Ambience
HDMI input
No service
Music
Off
Auto
Sound menu
Mode
Ambience
HDMI input
10
Sound quality can be improved when watching music scene
or drama by selecting the appropriate Music or Speech
mode.
Bass
Treble
Balance
Headphone volume
MPX
Mode
Ambience
HDMI input
Ambience provides a dynamic enhancer to simulate
improved spatial effects.
Sound menu
Displayed during HDMI input mode.
Allows you to choose from Auto, Digital and Analogue.
Select to fit the input signal.
Auto
: Set in normal use
Digital
: HDMI cable connection
Analogue : HDMI-DVI adapter cable connection
See page 35.
Bass
Treble
Balance
Headphone volume
MPX
Mode
Ambience
HDMI input
No service
Music
Off
Auto
No service
Music
Off
Auto
Sound menu
Bass
Treble
Balance
Headphone volume
MPX
Mode
Ambience
HDMI input
No service
Music
Off
Auto
Setup menu
Press the MENU button.
MENU
MODE
Move to choose Setup menu.
OK
Access Setup menu.
Move to choose menu option.
Adjust chosen option or access chosen menu.
Press the EXIT button at any time to go back to watching TV.
1
2
3
4
5
6
7
8
9
C
0
N
EXIT
IDTV
Q-Link
Allows you to select which AV terminal is to be used for data
communication between this TV and a compatible recording
device. Choose from Off, AV2 and AV4. See page 26.
AV2 / AV4 out
Sound menu
Offers a choice of signals to send to the Scart terminal
selected in the Q-Link option. You can choose from the
Setup menu
current TV (Analogue, DVB) programme position, the signal
entering AV1 / AV2 / AV3 / AV4 or Monitor - the picture
Analogue mode
displayed on screen.
Component signal input cannot be output to these Scart Setup menu
AV2
Q-Link
Monitor
AV2 out
terminals.
Main menu
P i c t u r e menu
Teletext
Off timer
Text language
Tuning menu
System language
Teletext
Allows you to choose between TOP/FLOF or List mode.
See page 30-32.
Off timer
Switches the TV off within a preset time which you can choose DVB mode
Setup menu
from between 0 to 90 minutes in 15 minute intervals.
Q-Link
Text language
AV2 out
Teletext
Off timer
DVB Setup Menu
System language
Select character set, so that all characters needed are available
for text on teletext pages (e.g., cyrillic characters, etc.).
Mode Languages
West: English, French, German, Greek, Italian, Spanish, AV mode
Setup menu
Swedish, Turkish
Q-Link
East1: Czech, English, Estonian, Lettish, Rumanian, AV2 out
Teletext
Off timer
Russian, Ukrainian
Colour system
East2: Czech, English, German, Hungarian, Lettish, Polish, Volume correction
Text language
System language
Rumanian
Tuning menu
Provides access to many other features including
Programme edit and Auto setup. See page 12-16.
DVB Setup Menu
Provides access to setup the DVB operations. See page 17.
TOP
Off
West
AV2
Monitor
TOP
Off
AV2
Monitor
TOP
Off
Auto
West
System language When you first install the TV, the On Screen Display
language is set to German. System language lets you
change the language used for On Screen Displays.
Colour system
During AV mode, Colour system is displayed. Lets you
select the correct transmission standard for the transmission
signal being received.
Volume correction During AV and HDMI mode, Volume correction is
displayed.
You can adjust volume level of AV and HDMI mode. Volume
level is memorised.
11
Tuning menu – overview (Analogue mode)
In Analogue mode
Press the MENU button.
MENU
MODE
OK
Move to choose Setup menu.
Access Setup menu.
Move to choose Tuning menu.
Access Tuning menu.
1
2
3
4
5
6
7
8
9
C
0
N
Move to choose menu option.
IDTV
Adjust chosen option or access chosen menu.
Press the EXIT button at any time to go back to watching TV.
Press the OK button after having adjusted some features to store the new
settings as the default (replacing the factory setting).
Programme edit
Access in order to customize your programme settings
(e.g., adding or deleting a programme position). See page
13, 14.
EXIT
OK
Main menu
P i c t u r e menu
Sound menu
Auto setup
Allows you to automatically retune the TV. Useful if you
move house and wish to retune your TV to the local stations.
See page 15.
Setup menu
Setup menu
Q-Link
AV2 out
Teletext
Off timer
Text language
Tuning menu
System language
Manual tuning
Allows individual programme positions to be tuned manually.
See page 16.
Fine tuning
Use to make small adjustments to the tuning of an individual
station (useful for example when weather conditions are
affecting reception quality of a programme).
Programme edit
Auto setup
Manual tuning
Fine tuning
Volume correc.
Decoder (AV2)
Lets you adjust the volume level of individual stations. Use
this feature if the volume level varies significantly between
stations. Adjusting one station’s volume to bring it into line
with the other stations means you can avoid having to adjust
the volume each time you change channels.
Prog.
AV2
Monitor
TOP
Off
West
Access
Tuning menu
Access
Off
Programme edit
Volume correc.
1
2
3
4
5
:
:
:
:
:
Delete
Chan.
Name
Lock
CH44
CH51
CH41
CH47
CH37
ABC
XYZ
FTP
123
456
Off
Off
Off
Off
Off
Add
Move
Tuning menu
Decoder
(AV2 / AV4)
This option is used when a decoder is connected via
AV2 / AV4. Store the setting as On so that every time
this programme position is selected, the TV software is
set to handle the decoded information (this is important if
your decoder unit is connected to AV2 / AV4 via a Q-Link
device).
Programme edit
Auto setup
Manual tuning
Fine tuning
Volume correc.
Decoder (AV2)
Access
Off
Tuning menu
Programme edit
Auto setup
Manual tuning
Fine tuning
Volume correc.
Decoder (AV2)
Access
Off
Tuning menu
Programme edit
Auto setup
Manual tuning
Fine tuning
Volume correc.
Decoder (AV2)
12
Off
Download
Tuning menu – Programme edit (Analogue mode)
In Analogue mode
MODE
MENU
Press the MENU button.
OK
Move to choose Setup menu.
Access Setup menu.
Move to choose Tuning menu.
Access Tuning menu.
1
2
3
4
5
6
7
8
9
C
0
N
Move to choose Programme edit.
IDTV
Access Programme edit.
Move to choose programme position (e.g., Prog. 3).
Make required change, e.g., moving a programme channel (see the
relevant procedure below).
EXIT
Press the EXIT button at any time to go back to watching TV.
Press the OK button after having adjusted some features to store the
new settings.
OK
Adding / deleting a programme channel
Move the cursor to the programme to be deleted or added.
Programme edit
Prog.
Press the Green button to add a programme channel to the
programme position, or the Red button to delete one.
Red
Green
1
2
3
4
5
:
:
:
:
:
Chan.
Name
Lock
CH44
CH51
CH41
CH47
CH37
ABC
XYZ
FTP
123
456
Off
Off
Off
Off
Off
Add
Cancel
Press the same button again to confirm your decision.
Moving a programme channel
Move the cursor to the programme to be moved.
Programme edit
Prog.
Press the Yellow button.
Yellow
Choose the new position for the programme channel.
1
2
3
4
5
:
:
:
:
:
Chan.
Name
Lock
CH44
CH51
CH41
CH47
CH37
ABC
XYZ
FTP
123
456
Off
Off
Off
Off
Off
Confirm
Cancel
Press the Yellow button again to confirm your decision.
Tuning a programme channel
Move to the Chan. column.
Programme edit
Prog.
Increase or decrease the programme channel number (you will
see the TV retune to the new number as you change it) or use the
C button for Direct Channel Access. See page 7.
Press the OK button to store this change.
1
2
3
4
5
:
:
:
:
:
Chan.
Name
Lock
CH44
CH51
CH41
CH47
CH37
ABC
XYZ
FTP
123
456
Off
Off
Off
Off
Off
C
OK
13
Tuning menu – Programme edit (Analogue mode)
Renaming a programme channel
Move to the Name column.
Programme edit
Prog.
1
2
3
4
5
Choose the new character. The box at the bottom of the screen shows
the character currently selected.
:
:
:
:
:
Chan.
Name
Lock
CH44
CH51
CH41
CH47
CH37
XYZ
FTP
123
456
Off
Off
Off
Off
Off
ABCDEFGHIJKLMNOPQRST
UVWXYZ+-. 0123456789
Move to the next character position.
Continue until renaming is done.
Press the OK button to store the new name.
OK
Locking a programme channel
You may wish to lock a programme channel to prevent access to it.
Programme edit
Prog.
1
2
3
4
5
Move to the Lock column.
Choose between Lock On or Lock Off.
Press the OK button to store the new setting.
:
:
:
:
:
Chan.
Name
Lock
CH44
CH51
CH41
CH47
CH37
ABC
XYZ
FTP
123
456
Off
Off
Off
Off
Off
OK
Note:
When a programme position is locked, Direct Channel Access
using the C and numeric buttons on the remote control is not
available.
Copying programme information to a recording device
You can copy programme information to a compatible recording device
connected to AV2 / AV4. See page 34 for connection information.
Press the Blue button.
Programme data will now be sent to the recording device(s). This
might take a few seconds, depending on the number of stations stored.
If the message “Feature not available” appears on the screen, the
television is unable to send the programme information to the recording
device(s). See the device’s instruction book for further information.
Note:
This is not available when you choose Q-Link Off in Setup menu.
14
DOWNLOAD IN PROGRESS
PLEASE WAIT
Blue
Programme : 63
Remote control unavailable
Tuning menu – Auto setup (Analogue mode)
Auto setup automatically retunes your TV. This feature is useful if, e.g., you move house and wish to retune your TV
to receive the local stations.
In Analogue mode
MENU
Press the MENU button.
MODE
OK
Move to choose Setup menu.
Access Setup menu.
Move to choose Tuning menu.
1
2
3
4
5
6
7
8
9
C
0
Access Tuning menu.
N
Move to choose Auto setup.
Access Auto setup.
IDTV
Notes:
• If you proceed with the next step analogue tuning data will be
erased (all analogue stations and their programme positions stored
in your TV’s memory will be wiped out so the new settings can be
stored).
• If you exit the procedure after this point and before Auto setup is
complete, no station information will be stored. Restart and complete
the Auto setup procedure so that the TV is retuned.
Press to start Auto setup.
WARNING
All analogue tuning
data will be erased
Start Auto Setup
Exit
Return
OK
The TV will search for, locate, store and then sort into
order your local stations.
CH12
AUTO SETUP IN PROGRESS
SEARCHING :
PLEASE WAIT
If compatible recording device is connected via the AV2 /
AV4 terminal, programme data will be sent to the device
via Q-Link. See page 26.
02
78:01
41
Exit
Return
Once this operation is completed the TV will display the
programme now stored on programme position 1.
Press the EXIT button at any time to go back to watching
TV (please read the Notes in the above procedure).
EXIT
15
Tuning menu – Manual tuning (Analogue mode)
It is possible to retune individual programme positions:
In Analogue mode
MENU
Press the MENU button.
MODE
OK
Move to choose Setup menu.
Access Setup menu.
Move to choose Tuning menu.
1
2
3
4
5
6
7
8
9
C
0
Access Tuning menu.
N
Move to choose Manual tuning.
Access Manual tuning.
IDTV
Select the programme position to be tuned.
1
CH12
Press repeatedly until required station is found.
Manual tuning
When the desired station is found, press the OK button to store.
The programme position will flash.
OK
02
EXIT
Press the EXIT button at any time to go back to watching TV.
C
78:01
41
Search down/up
Store
Exit
Return
9 Direct entry
0
Note:
If your VCR is connected to this TV by an RF cable only, choose programme position “0” to tune to the VCR
signals.
Manual tuning (via front panel) (Analogue mode)
It is also possible to use the control panel buttons on the front of your TV to tune individual programme positions:
Press the F button until Tuning mode is reached.
Press the –/ or +/ button to access Tuning mode.
Press the TV/AV button to move between Change
programme, Search and Change TV system.
Press the –/ or +/ button to change programme position
or start search.
When the desired station is found, press the STR button
to store.
The programme position will flash.
Repeat above procedure to tune additional programme
positions.
Press the F button at any time to go back to watching TV.
16
STR
F
TV/AV
1
CH12
SC1
Manual tuning
-, +
TV / AV
STR
F
:
:
:
:
Search
Move cursor
To store
To exit
02
STR
78:01
F
-/
+/
41
TV / AV
DVB Setup Menu – overview (DVB mode)
In DVB mode
Press the MENU button.
MENU
MODE
OK
Move to choose Setup menu.
Access Setup menu.
Move to choose DVB Setup Menu.
Access DVB Setup Menu.
1
2
3
4
5
6
7
8
9
C
0
N
Move to choose menu option.
Adjust chosen option or access chosen menu.
Press the EXIT button at any time to go back to watching TV.
Profile Edit
Allows you to select your favourite programme positions and
display them in the Information banner. See page 18.
Tuning Menu
Provides access to many other DVB tuning features.
See page 19.
Tuner Lock
Prevents you from accidentally changing programme
position while recording a DVB broadcast. If the TV is
switched into Standby mode while Tuner Lock is On, the
DVB tuner will remain active to ensure recording can still
take place.
Use this function for the recording without watching DVB
broadcast. Do not switch the main power button on the unit
Off during recording.
Even if the main power button is switched On and Off, this
setting is not changed.
IDTV
EXIT
Main menu
P i c t u r e menu
Sound menu
Setup menu
Setup menu
Q-Link
AV2 out
Teletext
Off timer
DVB Setup Menu
System language
AV2
Monitor
TOP
Off
Access
DVB Setup Menu
Profile Edit
Tuning Menu
Tuner Lock
Multi Audio
Teletext
System Setup
System Update
Access
Off
ger
ger
Note:
While recording a DVB programme, it is possible to change
to the analogue programme positions to watch.
Multi Audio
Allows you to select from several sound tracks. The number
of options available depends on each broadcast.
Teletext
Allows you to select the language in teletext mode. The
number of options available depends on each broadcast.
System Setup
Provides access to various specialized DVB options.
See page 21.
System Update
Allows you to download new software to the television.
See page 23.
17
Profile Edit (DVB mode)
The Profile Edit menu allows you to select your favourite programme positions and display them in the Information
banner, to allow quick and easy access to the programmes you watch most often. The programme number is given
sequentially.
You can make the 4 profile lists.
In DVB mode
MENU
Press the MENU button.
MODE
OK
Move to choose Setup menu.
Access Setup menu.
Move to choose DVB Setup Menu.
1
2
3
4
5
6
7
8
9
C
0
Access DVB Setup Menu.
N
Move to choose Profile Edit.
Access Profile Edit.
IDTV
Add a programme to the Profile list
DVB Setup Menu
Profile Edit
Tuning Menu
Tuner Lock
Multi Audio
Teletext
System Setup
System Update
Move to the programme position in All Services which you wish
to add to the profile list.
Press the Green button repeatedly to cycle through the profiles
(Profile 1 to 4).
Press the Yellow button to add a programme to the profile list.
Press the Blue button to add all the programmes to the profile
list.
Press the OK button to store your Profile list.
Green
Access
Off
ger
ger
Profile Editor
All Services
Yellow
Profile 1
1 Das Erste
2 arte
3 PHOENIX
Blue
4 ARD-MHP-Data
OK
Select programme
Store
Exit
Return
Edit the Profile list
Select Profile
Move to the profile list.
Add
Profile Editor
All Services
When the profile list is highlighted
Press the Red button to edit the profile name.
Press the Green button to move the programme.
1. Move the programme to another position with the up or
down cursor button.
2. Press the Green button to confirm.
3. Press the OK button to store.
Press the Yellow button to delete the programme.
Press the Blue button to delete all channels.
Press the OK button to store your Profile list.
2 ARD-MHP-Data
Select programme
Select list
Store
Exit
Return
Edit Name
Move
MENU
18
1 arte
3 PHOENIX
OK
Press the EXIT button at any time to go back to watching TV.
Profile 1
1 Das Erste
2 arte
4 ARD-MHP-Data
Press the MENU button to return to the DVB Setup Menu.
A list of profiles can be accessed by pressing the
or the GUIDE button.
See page 25.
Add All
EXIT
button
GUIDE
Delete
Delete All
DVB Tuning Menu (DVB mode)
DVB Tuning Menu provides access to DVB Tuning features.
In DVB mode
Press the MENU button.
MENU
MODE
OK
Move to choose Setup menu.
Access Setup menu.
Move to choose DVB Setup Menu.
1
2
3
4
5
6
7
8
9
C
0
Access DVB Setup Menu.
N
Move to choose Tuning Menu.
Access Tuning Menu.
IDTV
Move to choose menu option.
Adjust chosen option or access chosen menu.
Press the EXIT button at any time to go back to watching TV.
Auto Setup
Automatically retunes your TV. DVB stations will be located,
sorted into order and stored.
The present DVB tuning data will be erased.
Add New Service You can add new DVB stations while retaining existing
tuning data. When the New Services Found message
appears new DVB stations are available to add to your
existing DVB programme list.
The present DVB tuning data is not erased.
EXIT
DVB Setup Menu
Profile Edit
Tuning Menu
Tuner Lock
Multi Audio
Teletext
System Setup
System Update
Access
Off
ger
ger
DVB Tuning Menu
DVB Auto Setup
Please Wait !
New Service
Message
Signal Quality
This TV continually scans for updated DVB services
and notifies you of any changes. Set to On to receive
notification. Set to Off if you do not wish to be informed of
any updates.
Access
Auto Setup
Add New Service
New Service Message
Signal Quality
Prog. Channel
On
5
Service Name
69
NetID.
TS ID. Quality
4
34 VOX
12302
4158
9
5
54 N24
12302
4158
9
6
54 ProSieben
12302
4158
9
7
54 KABEL1
12302
4158
9
8
54 SAT.1
12302
4158
9
This will take about 3 mins.
Add New Services
Please Wait !
5
69
Service Name
NetID. TS ID. Quality
The signal quality function displays an indication of signal Prog. Channel
quality for each DVB programme position.
The DVB system requires a good quality signal to provide the
best picture. When viewing analogue pictures, interference This will take about 3 mins.
such as signal reflection from nearby buildings or mountains
causes ‘ghosting’, but still provides a viewable picture. For
the DVB system, interference such as this can disrupt the New Service Message On
flow of data causing the picture to appear to be made up
New DVB Service Found!
of large blocks, or to freeze intermittently. If the picture
Press OK to add new service
Press EXIT to lgnore
disappears completely, this could mean that signal quality
is very poor. If this happens often, you may need to improve
your aerial system to provide a better signal.
19
DVB Tuning Menu – DVB Auto Setup (DVB mode)
DVB Auto Setup automatically retunes your TV. This feature is useful if, e.g., you move house and wish to retune
your TV to receive the local stations.
In DVB mode
MENU
Press the MENU button.
MODE
OK
Move to choose Setup menu.
Access Setup menu.
Move to choose DVB Setup Menu.
1
2
3
4
5
6
7
8
9
C
0
Access DVB Setup Menu.
N
Move to choose Tuning Menu.
Access Tuning Menu.
IDTV
Move to choose Auto Setup.
Access Auto Setup.
Notes:
• If you proceed with the next step DVB tuning data will be erased
(all DVB stations and their programme positions stored in your TV’s
memory will be wiped out so the new settings can be stored).
• If you exit the procedure after this point and before Auto Setup is
complete, no station information will be stored. Restart and complete
the Auto Setup procedure so that the TV is retuned.
Press to start Auto Setup.
WARNING
All digital tuning
data will be erased
OK
Start Digital Scan
Exit
Return
The TV will search for, locate, store and then sort into
order your local stations.
DVB Auto Setup
Please Wait !
Prog. Channel
Once this operation is completed the TV will display the
programme now stored on programme position 1.
EXIT
Press the EXIT button at any time to go back to watching
TV (please read the Notes in the above procedure).
69
NetID.
TS ID. Quality
34 VOX
12302
4158
9
5
54 N24
12302
4158
9
6
54 ProSieben
12302
4158
9
7
54 KABEL1
12302
4158
9
8
54 SAT.1
12302
4158
9
This will take about 3 mins.
Exit
20
5
Service Name
4
DVB System Setup (DVB mode)
The DVB System Setup menu provides access to DVB specific options.
In DVB mode
Press the MENU button.
MENU
MODE
OK
Move to choose Setup menu.
Access Setup menu.
Move to choose DVB Setup Menu.
1
2
3
4
5
6
7
8
9
C
0
Access DVB Setup Menu.
N
Move to choose System Setup.
Access System Setup.
IDTV
Move to choose menu option.
Adjust chosen option or access chosen menu.
Press the EXIT button at any time to go back to watching TV.
Pressing the OK button after having adjusted some features will store the
new setting as the default (replacing the factory setting).
Common Interface The Common Interface Module menu provides access
Module
to functions contained on a Common Interface Module
inserted into the CI slot, located at the rear of the TV. See
page 22.
Preferred Language This option allows you to select the initial language for
Setting
Audio and Teletext.
Time Zone
This function will adjust the time data automatically.
Auto : The time data will be adjusted according to your
area automatically.
Others : The time data will be corrected based on GMT.
Display Timeout
This option allows you to set how long the information
banner stays on screen. Select from 0 (No display) to 10
seconds in 1 second increments. See page 25.
EXIT
OK
DVB Setup Menu
Profile Edit
Tuning Menu
Tuner Lock
Multi Audio
Teletext
System Setup
System Update
Off
ger
ger
Access
DVB System Setup
Common Interface Module
Preferred Language Setting
Time Zone
Display Timeout
Access
Auto
3 seconds
21
Common Interface Module (DVB mode)
The Common Interface Module menu provides access to software contained on Common Interface (CI) Modules.
These can be inserted in the “CI” slot located at the rear of the TV.
IMPORTANT NOTES:
• Switch off the TV using the front panel switch before inserting or removing a module.
• If you are installing a TV software update, please follow the dedicated instructions supplied with the
module.
• Insert / remove a module straightly to the CI slot.
Insert the CI module:
Some Common Interface Modules may be a two piece design consisting
of a card reader together with the viewing card. When using this design
of card, first insert the card reader firmly into the CI slot on the TV.
Secondly, insert the viewing card into the reader.
Commom Interface
Switch on the TV.
In DVB mode
Press the MENU button.
MENU
MODE
OK
Move to choose Setup menu.
Access Setup menu.
Move to choose DVB Setup Menu.
1
2
3
4
5
6
7
8
9
C
0
Access DVB Setup Menu.
N
Move to choose System Setup.
Access System Setup.
IDTV
Move to choose Common Interface Module.
Access Common Interface Module.
Access the module.
If no module is inserted the message “No module inserted” will be
displayed.
(If you have inserted a module, check that it is fully inserted.)
The features that now appear on screen are dependent on the contents
of the selected Common Interface Module.
Refer to the instructions supplied with the card or contact the vendor.
DVB System Setup
Common Interface Module
Preferred Language Setting
Time Zone
Display Timeout
If you see the
Slot 1: No module inserted
OK
symbols, use the cursor buttons.
If you see a line of key words displayed in red, green, yellow and blue,
use the coloured buttons to operate the functions.
The EXIT button should always allow you to exit the CI software.
22
Auto
3 seconds
Common Interface
In all cases, it is possible to navigate the pages using buttons on the
remote control, but because the commands available must apply to all
manufacturers of DVB equipment, some on screen commands may not
correspond exactly to the remote control buttons.
For example:
For the on screen command ‘select’ or ‘go’, use the OK button.
Access
EXIT
Access
DVB System Update (DVB mode)
From time to time new versions of software will become available to enhance the performance and features of this TV.
Auto Update Search in Standby (Overnight)
During the night time, this TV will automatically search for any new available software being broadcast. If a new
software version is found, the unit will automatically download and install this new version. At the end of this process
the unit will reset. Auto Update Search in Standby will occur at 03:00 and 05:00 every day.
In DVB mode
Press the MENU button.
MENU
MODE
Move to choose Setup menu.
OK
Access Setup menu.
Move to choose DVB Setup Menu.
Access DVB Setup Menu.
Move to choose System Update.
1
2
3
4
5
6
7
8
9
C
0
N
Access System Update.
IDTV
Move to choose Auto Update Search in Standby.
Choose between On or Off.
Set to On to search for new software and update automatically in Standby mode.
This does not work when the unit is off.
If there is a new version software being broadcast, the TV will download this
automatically.
Auto Update Search in Standby will only occur if:
• The unit is in Standby mode
• No recording is being made at 03:00 or 05:00
Set to Off if you do not want new software to be automatically downloaded.
In this case a new software banner will appear when the TV set is switched on,
if new software is being broadcast.
The message might be the notification beforehand. In this case, the schedule
information (the date that the new version can be used) will appear.
Press the OK button to download the new version.
The TV will begin download of the new software version. This can take up to
about 20 minutes.
Press the EXIT button to exit without download.
DVB Setup Menu
Profile Edit
Tuning Menu
Tuner Lock
Multi Audio
Teletext
System Setup
System Update
Off
ger
ger
Access
DVB System Update
Auto Update Search in Standby
System Update Search Now
Software Licence
On
OK
EXIT
New version 1.00 found.
Do you really want to update the software and reboot the system?
Press OK to download the new version
Press EXIT to lgnore
To ensure that your TV automatically updates when new software is available, please place the TV in Standby
last thing at night when you have finished viewing.
23
DVB System Update (DVB mode)
System Update Search Now (Manual Download)
To manually check if a new software version is available, select System Update Search Now in DVB System Update
menu.
In DVB mode
Press the MENU button.
MENU
MODE
Move to choose Setup menu.
OK
Access Setup menu.
Move to choose DVB Setup Menu.
Access DVB Setup Menu.
Move to choose System Update.
1
2
3
4
5
6
7
8
9
C
0
N
Access System Update.
Move to choose System Update Search Now.
IDTV
Access System Update Search Now.
The TV will search for new versions of software and indicate whether a
newer version is available or not. This search process may take a few
minutes.
If a newer software version is found, an on screen message will inform
the user that it is available. The user is given the chance to download this
version.
The message might be the notification beforehand. In this case, the schedule
information (the date that the new version can be used) will appear.
Press the OK button to download the new version.
The TV will begin download of the new software version. This can take up
to about 20 minutes.
Press the EXIT button to exit without download.
DVB System Update
Searching for new software version: Please wait!
Current software version 0.30
Exit
Return
OK
EXIT
Please do not switch off the TV or press any buttons while this download is in progress. The TV will reset
after the software download is complete.
Press the MENU button to return to DVB System Update
menu.
Press the EXIT button to exit from menus.
Software Licence
Access to show the information of the Software Licence.
24
MENU
EXIT
Information banner
In DVB mode
MODE
Information banner will appear when changing channel, pressing the button or the GUIDE
button. The banner gives the user information about the channel and programme currently
being viewed. The banner will time out and disappear from the screen after a set time period,
this time period can be set in the DVB System Setup menu. See page 21.
Displayed if programme type is
Current Programme radio-channel or data-channel
Current Time
Current programme title
Now or Next
1 Das Erste
OK
GUIDE
1
2
3
4
5
6
7
8
9
C
0
20:30
N
Lotti auf der Flucht
20:00 - 20:55
For info press
Now
Subtitle
Multi-Audio
TXT
Encrypted No Signal
ger
All Services
Multi Audio
Profile
PULL
IDTV
Features Available
Programme Duration
Display of scrambled programmes
Teletext information will be displayed, if programme has teletext.
In case of bad signal or non correct
programme-number a message will be displayed.
Press the left or right cursor button while banner is displayed to switch between Now and Next.
1 Das Erste
Lotti auf der Flucht
20:00 - 20:55
20:30
For info press
ger
All Services
Multi Audio
Profile
Now
1 Das Erste
News
20:55 - 21:00
20:30
For info press
ger
All Services
Multi Audio
Profile
Next
This switches between the information for the current programme title being shown (Now) and
the next programme title to be shown (Next).
Press the up or down cursor button to step through the banner information for all
programmes.
Press the OK button to view a programme.
While the banner appears
Press the button or the GUIDE button to display an extended banner showing any information
available on the current selected programme.
If the information is out of the screen, press the up or down cursor button to scroll through the
information.
Press the button or the GUIDE button while in extended banner mode to return to normal
banner view.
To clear the banner from the screen while in extended banner mode, press the EXIT button.
Changing Category
Press the Blue button while in the banner to scroll through available categories.
For example:
All Services : All available Services
User
Profiles : 4 individual Profiles set up by user (see page 18)
All Services
User Profiles
(Profile 1 to 4)
Changing Sound track
Press the Yellow button while in the banner to scroll through available sound tracks.
Press the EXIT button to exit the banner at any time.
OK
GUIDE
EXIT
Blue
Yellow
EXIT
In Analogue mode
Pressing the button will display the analogue channel information for a few seconds. This
will then be timed out to display just the programme position number near the top left corner
of the screen.
To remove this programme position number, press the button again.
25
Q-Link
Q-Link allows the television to communicate with a compatible VCR or DVD Recorder.
For Q-Link communication to work, the TV must be connected to a recording device with the “Q-Link”, “NEXTVIEWLINK”,
“DATA LOGIC”, “Easy Link”, “Megalogic” or “SMARTLINK” logo using a “fully wired” Scart cable between the AV2 /
AV4 terminal of the television and the appropriate terminal on your VCR or DVD Recorder.
For connection to the appropriate Scart terminal on the recording device, refer to the device’s instruction book.
When using a “NEXTVIEWLINK” device the main features possible are the following:
Preset Download
This allows the programme order from the TV to be downloaded to the recording device, helping to ensure that correct
recordings are made; there are several ways to perform this operation:
1. During installation as explained in the “Quick Start Guide” on page 5, 6.
2. When Auto setup is started from within the Tuning menu. See page 12.
3. Preset download started from the recording device, refer to the device’s instruction book.
Because a recording device cannot tune to DVB stations, only the analogue programme positions are
downloaded to the device.
MODE
OK
What You See Is What You Record (DIRECT TV RECORDING)
This will allow the immediate recording of the programme currently shown on the TV, by the recording
device attached to the Scart terminal, which can be chosen using “Q-Link”. See page 11.
Press the DIRECT TV REC button.
DIRECT
TV REC
If the recording device is in Standby mode with usable recording media inserted, it will automatically
switch on when you press the DIRECT TV REC button.
If a “Q-Link” device is connected, a message will appear on the TV screen showing what is being recorded,
or if it is not possible to record. Some “Q-Link” compatible devices will only display the message when
on the VCR programme position “0” or in AV mode. Refer to the device’s instruction book.
Recording in progress
The recording device is recording the programme signal
from its own tuner. If you wish you can switch off the TV
and leave the device recording in the normal way.
1
2
3
4
5
6
7
8
9
C
0
N
IDTV
No recording -Check tape or disc
The tape or disc may have been “write protected”,
missing or may be damaged. The device may already be
recording. Refer to the device’s instruction book.
Recording DVB broadcasts
If you press the DIRECT TV REC button while watching a DVB broadcasts, the recording device will automatically
switch to its AV input to record the DVB signal from the TV (via the SCART cable), and the DVB programme position
will be locked. If you attempt to select another DVB programme position while recording, you will see the message
“DVB Tuner Locked”. Press the OK button to clear the message, or the EXIT button to unlock the programme. Beware
that if you press the EXIT button, the DVB programme will be unlocked – the EXIT button stops the recording.
Additionally, when using a “Q-Link” device the main features possible are the following:
The following features are only available from the device connected to the Scart terminal selected using “Q-Link”.
See page 11.
TV / Recording device Auto Power On
If you insert pre-recorded media into the recording device and press the Play button whilst the TV is in Standby mode,
the TV will automatically switch on and select the correct AV input so that you can view the content.
Recording device Auto Power Standby
When the TV is switched into Standby mode, the recording device will also switch into Standby mode if there is no
media inserted, or if there is media inserted and the device is in Rewind or Stop mode. If a VCR is rewinding a tape,
it will not switch into Standby mode until rewinding has finished.
Recording device Image View On
If the TV is in Standby mode and the recording device sends a menu to be displayed on the TV screen (e.g., Main
menu), the TV will automatically switch On and the menu will be displayed.
This TV will also communicate with other recording device’s that bear the following logos:
• “DATA LOGIC” (a trademark of Metz Corporation)
• “Megalogic” (a trademark of Grundig Corporation)
• “Easy Link” (a trademark of Philips Corporation)
• “SMARTLINK” (a trademark of Sony Corporation)
Important Note:
Some recording devices may not support all or some of the above functions. Refer to the instruction book for the device.
If Q-Link functions do not work, check the connection and ensure that the scart lead is a fully-wired type.
26
Aspect Controls
The Widescreen TV will allow you to enjoy viewing the picture at its optimum size and aspect, including widescreen
cinema format pictures.
Press the ASPECT button repeatedly to move through the aspect
options:
ASPECT
MODE
OK
Panasonic Auto, 16:9, 14:9, Just, 4:3, Zoom1, Zoom2 and Zoom3
OR
Press the ASPECT button. Whilst the on screen selector keys are
displayed, use the Red or Green buttons to move in either direction
through the aspect options.
Red
1
2
3
4
5
6
7
8
9
C
0
Green
N
Note:
This is not available for 720p and 1080i signals input. Aspect is fixed to 16:9.
IDTV
Panasonic Auto
Panasonic Auto determines the best aspect ratio to use to fill your screen. It
does this using a four step process to determine if the picture being viewed is
a widescreen picture.
WIDE
If Panasonic Auto detects a widescreen signal it switches into the appropriate
widescreen mode. If Panasonic Auto does not detect a widescreen signal then
this advanced TV set enhances the picture for optimum viewing pleasure.
The text shown on the screen indicates how Panasonic Auto determined
which ratio to use:
Panasonic Auto switches to the appropriate widescreen ratio.
If black stripes above and below the picture are detected, aspect ratio changes
automatically.
Panasonic Auto chooses the best ratio and expands the picture to fill the
screen. This process can take several minutes, depending on the darkness
of the picture.
“WIDE” ap pears in the top left
of the screen, Panasonic Auto
switches to the appropriate 16:9
or 14:9 widescreen ratio.
Panasonic Auto
You may prefer to manually select one of the other aspect options available
to view the picture.
Notes:
• If, in Panasonic Auto mode, you experience problems with the screen display
size when playing back widescreen format recordings from your VCR then
it is possible that the tracking control of your VCR requires adjustment (your
VCR instruction book will contain adjustment details).
• The widescreen aspect ratios of different films and programmes can vary.
If these are wider than a standard 16:9 aspect picture then a black band may
be visible at the top and bottom of the screen.
• “WIDE” will appear in the top left corner of the screen and picture aspect
changes accordingly in any aspect modes, if a widescreen identification signal
(WSS) is detected or a control signal is found through a Scart terminal.
• Automatic aspect ratio adjustment by WSS signal is not available for
progressive and high definition component signals input.
“Panasonic Auto” appears in the
top left of the screen. The best
ratio is chosen and the picture
expanded to fill the screen.
Panasonic Auto
Press the ASPECT button, then
use the Red or Green buttons to
move in either direction through
the aspect options.
27
Aspect Controls
16 : 9
16 : 9
16:9 will display a true 16:9 (anamorphic) picture with no aspect distortions.
16 : 9
14 : 9
14 : 9
14:9 will display a 14:9 picture at its standard 14:9 size without any
stretching.
14 : 9
Just
Just
Use Just when you wish to expand a 4:3 picture to fill the whole screen (rather
than watching a programme with black stripes down the left and right sides of
the picture).
The 4:3 picture will be stretched horizontally so that the image fills the screen,
this is done in such a way that the stretching is only obvious at the left and
right edges of the screen.
4:3
Just
4:3
4:3 will display a 4:3 picture at its standard 4:3 size with no aspect
distortions.
4:3
Zoom1
Zoom1
Zoom1 will display 16:9 letterbox or 4:3 pictures with no aspect distortions.
Zoom1
Zoom2
Zoom2
Zoom2 will display 16:9 anamorphic letterbox pictures as a full screen display
with no aspect distortions.
Zoom2
Zoom3
Zoom3
Zoom3 will display 21:9 letterbox pictures as a full screen display with no
aspect distortions.
16:9 will display the picture at its maximum size but with slight stretching.
Zoom3
28
VCR / DVD operation
The Remote Control is capable of operating some functions of selected Panasonic VCRs and DVD (Digital Versatile
Disc) equipment. Some VCR and DVD equipment have different functions, so to ensure compatibility please refer to
the equipment’s instruction book or consult your dealer for details.
VCR
DVD
DVB DIRECT
Analogue TV REC
MODE
GUIDE
VCR / DVD switch
Use this switch to select whether controls operate the DVD
equipment or VCR.
Standby
Press to switch the VCR, DVD or DVD recorder to Standby
mode.
Press again to switch back on.
TV/AV
OK
MENU
TEXT
EXIT
F.P.
Play
Press to playback the tape or DVD.
INDEX HOLD
1
2
3
4
5
6
7
8
9
Stop
Press to stop the tape or DVD.
Skip / Fast Forward / Cue
VCR: Press to fast forward the tape. In Play mode, press
to view the picture rapidly forward (Cue).
DVD: Press to skip to the next track or title.
Press and hold to search forward.
0
C
VCR
Skip / Rewind / Review
VCR: Press to rewind the tape. In Play mode, press to view
the picture rapidly in reverse (Review).
DVD: Press to skip to the previous track or title.
Press and hold to search backward.
ASPECT
N
REC
VCR
DVD
Pause / Still
Press in Play mode, the picture will pause.
Press again to restart play.
DVD: Press and hold for slow-motion play.
PROGRAMME
PROGRAMME
IDTV
REC
Programme Up / Down
Press to increase or decrease the programme position by
one.
Record
Press this button to start recording.
29
Teletext operation
• Teletext features may vary depending on the Broadcasting Companies and is only available if the channel selected
is transmitting Teletext.
• Pressing the MENU button three times whilst in Teletext operation will display the contrast function with a cyan bar,
press the left and right cursor buttons to alter the setting as required.
• Pressing the MENU button whilst in Teletext operation will display special function options at the bottom of the
screen.
• Pressing the Volume up / down button whilst in Teletext operation will display the volume function with a green bar,
press the volume up / down button to alter the setting as required.
What is List mode?
In List mode, four differently coloured page numbers are situated at the bottom of the screen. Each of these numbers
can be altered and stored in the TV’s memory.
What is TOP/FLOF mode?
In TOP/FLOF mode, four differently coloured subjects are situated at the bottom of the display. To access more
information about one of these subjects, press the appropriately coloured button. This facility enables fast access to
information on the subjects shown.
TV / Teletext mode
Press the TEXT button to switch between the current programme and teletext.
TEXT
1
2
3
4
5
6
7
8
9
0
VCR
MENU
Green
MENU
Red
Page Selection
Pages can be selected in two ways:
a. Press the Up / Down cursor buttons to increase or decrease the page number by one.
b. By entering the page number, using 0 - 9 on the remote control.
Full / Top / Bottom
Press the MENU button to display special functions, followed by the Green button.
Press the Green button again to expand the BOTTOM half.
Press again to return to normal (FULL) size.
Reveal
Press the MENU button to display special functions, followed by the Red button to reveal
hidden words e.g., quiz page answers. Press again to hide.
Red / Green / Yellow / Blue buttons
In TOP/FLOF mode they correspond to the differently coloured subjects.
In List mode they correspond to the differently coloured page numbers.
1
2
3
4
5
6
7
8
9
0
VCR
HOLD
30
OK
List Store
In List mode the four page numbers can be altered.
DVB mode: any programme positions are available
Analogue mode: programme positions 1 - 25 only
To do this, press one of the four coloured buttons and enter the new page number.
Press and hold the OK button, the page numbers will change to white indicating that the
page is stored.
HOLD
To hold the Teletext page when viewing multi-page information.
Press again to return to automatic page update.
Teletext operation
It is not possible to change the programme position when in News flash, Update or Sub Coded Page Access
operation.
Blue
1
2
3
4
5
6
8
9
7
OK
F.P.
0
VCR
MENU
Yellow
Favourite Page (F.P.)
Stores a favourite page in memory for instant recall. To store such a page, the TV must
be in List mode, and the programme position in Analogue mode must be from 1 - 25 (any
programme positions are available in DVB mode).
Press the Blue button, select the page number, then press and hold the OK button. The
page number is now stored.
Press the F.P. button to recall this page.
Update Display
Press the MENU button to display special functions, followed by the Yellow button to view
the TV picture whilst searching for a Teletext page (this is not necessary in Picture and text
mode, as the picture is displayed on the left of the screen). When found, the screen will
display the page number at the top left. Press the Yellow button to view the page.
Press the TEXT button again to return to normal TV operation.
News Flash
When a news flash page has been selected, press the MENU, Yellow buttons, to view the
TV picture. When an update is received, the page number will be displayed on screen.
Press the Yellow button to display the News Flash.
Press the TEXT button to return to normal TV operation.
Update
Press the MENU, Yellow buttons to see the update of information on certain pages.
When an update is received, the page number will be displayed at the top left of the
screen.
Press the Yellow button to view the page.
Press the TEXT button to return to normal TV operation.
Accessing sub pages
When Teletext information exceeds one page, it may take some time for the automatic
changing of the sub pages to reach the sub page you require. As each sub page is found
its number is displayed at the top of the page so that you may select it; as more sub pages
are picked up, the display at the top of the page changes, so that you are always offered
the most recently transmitted selection of sub pages.
In Teletext operation, use the following procedure to access sub pages:
1
2
3
4
5
6
7
8
9
If the sub page you want to look at is not yet available, press the MENU button (to display
special functions) followed by the Yellow button to view the TV picture whilst waiting for
more sub pages to be found. The sub pages found will be displayed across the top of the
screen.
0
VCR
MENU
Yellow
When the sub page you are waiting for is available press the Yellow button to return to
viewing the Teletext pages, then use the left and right cursor buttons to select the sub
page of your choice.
The maximum number for sub page that can be entered is restricted to 79 by
broadcasters.
Notes:
• If you do not want to display the on screen selector keys on the TV picture whilst waiting
for a sub page to be found, press the MENU button to clear the keys from the screen.
Press again to redisplay the keys.
• If you have cleared the special function keys from the screen and then used the left and
right cursor buttons to select a sub page, whilst still viewing the TV picture, you must
press the MENU button then the Yellow button to display the Teletext page again.
• If the top of the page indicates that sub pages are being transmitted but the page displayed
never changes, then the ‘sub page number’ is there to show the page contents have been
updated, there are no sub pages.
31
Teletext operation
MENU
Blue
Alternatively, if you know which sub page you require, press the MENU button (to display
special functions) followed by the Blue button; T**** will be displayed where the page number
is normally found.
Enter desired sub page number before the T**** disappears.
e.g., to select page 6 enter 0, 0, 0 and 6.
Press the Yellow button to view the TV picture whilst waiting for more sub pages to be found.
The sub pages found will be displayed across the top of the screen.
When the page is available, press the Yellow button to view the page. Regardless of how
many pages are found, pressing the Yellow button will take you to the sub page which you
requested.
Press the TEXT button to return to normal TV operation.
INDEX
MENU
INDEX
When in TOP/FLOF operation
Press the INDEX button to return to the main index page.
Depending on the way information is transmitted, this may have to be pressed more than
once to return to the main index page.
Picture and text
Press the MENU button twice to display special functions, followed by the left or right cursor
button to select Picture and text On or Off.
Picture and text mode lets you see the current programme and a page of teletext side by
side. Whilst using this feature, the remote control affects the teletext page; if you wish to
make changes to the programme viewed press the TEXT button to return to watching the
programme on its own then make the desired changes.
Still
Press the HOLD button to freeze the picture.
Press again to return to watching the current programme.
HOLD
MODE
OK
1
2
3
4
5
6
7
8
9
C
0
N
IDTV
32
Connections
It is possible to connect a variety of additional equipment to this TV. The following pages detail how to connect external
equipment to the front and rear of the TV.
Once your equipment is connected, use the following procedure to view the input:
While viewing a TV channel
Press the TV/AV button.
TV/AV
MODE
Whilst the on screen selector keys are displayed, select the page by
pressing the Red or Blue button and then press coloured buttons to
select the AV source you wish to view.
Red button
: AV1 Scart terminal / Back page
Green button : AV2 Video, S-Video Scart terminal /
AV4 Video, S-Video Scart terminal
Yellow button : AV3 Audio, Video, S-Video terminals /
Component, HDMI terminals
Blue button : Next page / The on screen selector keys will disappear after a few seconds. If you
want to select an input when the keys are not shown, press any one
of the coloured buttons and the keys will reappear.
OK
Red
Blue
1
2
3
4
5
6
7
8
9
C
0
N
IDTV
Notes:
• You can also select an AV source using the TV/AV button on the
front panel of the TV.
Press the TV/AV button repeatedly until you reach the AV source
you wish to view.
• When in AV mode a reduced number of options are available
in the Sound and Setup menus (e.g., in the Setup menu there
is no Tuning menu option).
• If the external device has aspect adjustment, set it to 16:9 for
correct output display on this TV.
How to connect the Headphones / AV3 terminals
(M3 plug)
(Optional)
Connect the S-VIDEO or VIDEO terminal.
S-Video
OUT
VCR / S-VIDEO VCR
DVD PLAYER
CAMCORDER /
S-VIDEO CAMCORDER
VIDEO
Video
OUT
Audio
OUT
S-VIDEO
L
AUDIO
R
Notes:
• The volume level of the headphones can be adjusted by selecting “Headphone volume” from the Sound menu.
• Additional equipment and cables shown are not supplied with this TV set.
33
Connections
To bundle the cables with the clamper
To tighten:
To loosen:
Pull
Keep the
Pull
knob pressed.
Note: Do not put the RF cable and the mains lead together to avoid noise.
How to connect the Audio Output terminals
AV1
AV2
AV4
COMPONENT
AUDIO
IN
L
L
R
R
L
Amplifier to Speaker
System
Y
R
AUDIO
OUT
AUDIO
PB
RGB
VIDEO
VIDEO
S-VIDEO
RGB
VIDEO
S-VIDEO
PR
VIDEO
How to connect the AV1 / 2 / 4 Scart terminals
AV1
AV2
AV4
COMPONENT
L
Y
R
AV1:
VCR
SET TOP BOX
DVD PLAYER
DVD RECORDER
CAMCORDER
GAME CONSOLE /
COMPUTER(RGB)
AV2:
VCR / S-VIDEO VCR
Q-Link COMPATIBLE VCR
DVD PLAYER
DVD RECORDER
Q-Link COMPATIBLE
DVD RECORDER
CAMCORDER /
S-VIDEO CAMCORDER
AV1/2/4
AV4:
VCR / S-VIDEO VCR
Q-Link COMPATIBLE VCR
SET TOP BOX
DVD PLAYER
DVD RECORDER
Q-Link COMPATIBLE
DVD RECORDER
CAMCORDER /
S-VIDEO CAMCORDER
GAME CONSOLE /
COMPUTER(RGB)
AUDIO
PB
RGB
VIDEO
VIDEO
S-VIDEO
RGB
VIDEO
S-VIDEO
PR
VIDEO
How to connect the Component Input terminals
This terminal accepts progressive or non-progressive signals format, as well as high
definition 750(720)/50p, 750(720)/60p, 1125(1080)/50i and 1125(1080)/60i.
Y
Y
AV
AV1
Y, PB, PR PB
OUT
PB
PR
PR
DVD PLAYER
AV2
AV4
AUDIO IN
COMPONENT
L
L
Y
R
R
PB
AUDIO
AUDIO
OUT
L
L
R
R
RGB
VIDEO
VIDEO
S-VIDEO
RGB
VIDEO
S-VIDEO
PR
VIDEO
COMPONENT
AUDIO IN
Notes:
• Additional equipment and cables shown are not supplied with this TV set.
• Do not connect a computer with TTL output (5V) to this set.
• For Scart terminal wiring and applicable component signals information see page 38.
34
AUDIO
Connections
How to connect the HDMI Input terminal
HDMI (High Definition Multi media Interface) is the first all-digital consumer electronics A/V interface that supports
uncompressed standard. The HDMI terminal supports both video and audio information.
An HDMI-compliant device∗1, such as a Set Top Box or DVD player with HDMI or DVI output terminal can be connected
to the HDMI input terminal.
• If the external device has DVI output only, use a DVI to HDMI adapter cable∗2 to connect to the HDMI terminal.
• Connect the audio cables to the AUDIO IN terminals when using a DVI to HDMI adapter cable.
• Select the audio setting in HDMI input. See page 10.
SET TOP BOX
DVD PLAYER
AV
AV1
AV2
AV4
AUDIO IN
COMPONENT
HDMI
OUT
L
L
Y
R
HDMI IN
R
PB
AUDIO
AUDIO
RGB
VIDEO
VIDEO
S-VIDEO
RGB
VIDEO
S-VIDEO
PR
VIDEO
Notes:
• This input terminal is not intended for use with computers.
• 720p/1080i signals will be re-formatted to view on your display.
• If the external device has aspect adjustment, set it to 16:9 for correct output display on this TV.
• For applicable HDMI signals information see page 38.
Compatible sampling frequency of AUDIO signal through HDMI (L.PCM) : 48 kHz / 44.1 kHz / 32 kHz
Notes:
• This HDMI connecter is Type A.
• If you connect equipment without a digital output terminal, connect to the COMPONENT, S-VIDEO or VIDEO input
terminal on the TV so you can receive an analogue signal.
• The HDMI IN terminal can only be used with 480i, 480p, 576i, 576p, 720p or 1080i picture signals. Set the Digital
Set Top Box DIGITAL OUT terminal output setting to 480i, 480p, 576i, 576p, 720p or 1080i. For detailed information,
refer to the Digital Set Top Box instruction manual. If you cannot display the picture because your Digital Set Top
Box does not have a DIGITAL OUT terminal output setting, use the component input (or the S-Video input or Video
input). In this case the picture will be displayed as an analogue signal.
∗1. HDMI-compliant device is that has the HDMI Logo on it.
∗2. HDMI-DVI adapter cable: Consult your consumer electronics dealer for availability.
35
Troubleshooting
If there is a problem with your TV, please refer to the table below to determine the symptoms, then carry out the
suggested check. If this does not solve the problem, please contact your local Panasonic dealer, quoting the model
number and serial number (both found on the rear of the TV).
Symptoms
Picture
Checks
Sound
Aerial location, direction or connection
Noisy Sound
Snowy Picture
Aerial location, direction or connection
Multiple Images
Normal Sound
Electrical appliances
Cars / Motorcycles
Fluorescent lights
Noisy Sound
Interference
Switch on P-NR in Picture menu to reduce picture noise.
Volume level
Sound mute switched on.
No Sound
Normal Picture
No Sound
No Picture
TV set to AV mode.
Not plugged into AC outlet.
Not switched on.
Picture / Sound controls set at minimum levels.
Check if in Standby mode.
Colour controls set at minimum levels.
Normal Sound
No Colour
Poor or Distorted Picture
Normal Picture
Weak or No Sound
Weak or Distorted Sound
There may be red spots,
blue spots and green
spots on the screen.
Normal Sound
H
D
M
I
Poor Video.
(Snow noise, no picture, picture runs, etc.)
Poor Audio.
The error message appears.
36
Retune Channel (s).
Some programmes may not be received when both Aerial and CATV
signals are connected to the TV through a mixer. In this case, connect
either Aerial or CATV signal directly to the TV.
Sound reception may have deteriorated.
Switch MPX setting (Sound menu in Analogue mode) to Off until reception
improves.
This is a characteristic of liquid crystal panels and is not a problem. The
liquid crystal panel is built with very high precision technology giving you
fine picture details. Occasionally, a few non-active pixels may appear on
the screen as a fixed point of blue, green, or red.
Please note this does not affect the performance of your LCD.
HDMI cable is not connected securely.
Turn the power supply of the TV and connected equipment off then
turn on.
Check compatibility of input signal from the connected equipment.
The connected equipment must be EIA/CEA-861/861B compliant.
Change the audio setting of the connected equipment to L.PCM.
Check the setting of HDMI input in Sound menu.
If the problem is due to the digital audio connection, change to the
analogue audio connection.
Please consult an Authorized Service Center.
DVB Troubleshooting
Some problems will only occur when viewing DVB channels. Due to the different techniques involved in digital reception,
DVB signal quality can be poor even if you appear to have a strong signal when viewing analogue programmes.
The DVB system requires a good quality signal to provide the best picture. When viewing analogue pictures, interference
such as signal reflection from nearby buildings or mountains causes ‘ghosting’, but still provides a viewable picture.
For the DVB system, interference such as this can disrupt the flow of data causing the picture to appear to be made
up of large blocks, or to freeze intermittently. If the picture disappears completely, this could mean that signal quality
is very poor. If this happens often, you may need to improve your aerial system to provide a better signal. This TV
contains a complex microprocessor which enables you to view enhanced digital services. Occasionally this device
may need to be reset. This can be done by pressing the standby button on your remote control.
Symptoms
Checks
No DVB channels listed after Auto Setup.
Check that DVB transmissions are available from the
transmitter you are currently using. If not, try directing the
aerial at another local transmitter.
Check analogue transmissions. If picture quality is poor, you
will need to improve or change your aerial system to receive
DVB channels. Consult a local installer.
Blocky interference.
Picture freezes intermittently.
Blocky interference indicates that the signal quality is poor.
You should consider improving your aerial system.
To check the quality of your signal use the Signal Quality
feature (see page 19).
Good quality signal – indication is green.
Poor quality signal – indication is red.
I have a good aerial system, but still cannot receive
DVB stations.
If you have tried the previous solutions and are still unable to
receive DVB channels, you may need to provide dedicated
aerial feeds to the TV and other equipment.
This can be implemented using an aerial splitter or separate
aerials.
TV
Aerial Input
terminal
Separate
Aerial
Aerial Output
PULL
VCR
Aerial Input
terminal
Aerial Output
AERIAL
SPLITTER
Aerial Input
terminal
Separate
Aerial
Maintenance
To clean this set, wipe with a soft, dry cloth.
Neutral
If the surfaces are extremely dirty, use a soft cloth dipped in soap-and-water solution or a detergent
weak detergent solution.
• Use eyeglass cleaner to remove stubborn dirt from the LCD.
• Never use alcohol, paint thinner or benzine to clean this set.
• Before using chemically treated cloth, read the instructions that came with the cloth carefully.
• Do not wipe the LCD with water.
Wipe the cabinet with a soft cloth.
If the cabinet is heavily soiled, wipe with a well-wrung soft cloth dipped in neutral cleanser diluted with water.
CAUTION:
If water or similar substances get inside the monitor via the liquid crystal panel surface, a malfunction may result.
37
Input signal that can be displayed
Applicable input signal for Component (Y, PB, PR) and HDMI (∗ Mark)
Horizontal
frequency (kHz)
Vertical
frequency (Hz)
Component
HDMI
525 (480) / 60i
15.73
59.94
∗
∗
525 (480) / 60p
31.47
59.94
∗
∗
625 (576) / 50i
15.63
50.00
∗
∗
625 (576) / 50p
31.25
50.00
∗
∗
750 (720) / 60p
45.00
60.00
∗
∗
750 (720) / 50p
37.50
50.00
∗
∗
1,125 (1,080) / 60i
33.75
60.00
∗
∗
1,125 (1,080) / 50i
28.13
50.00
∗
∗
Signal name
Note:
Signals other than above may not be displayed properly.
Scart and S-video terminal information
AV1 Scart terminal (RGB, VIDEO)
Socket Earth
CVBS out (video)
CVBS earth
Red in
Red earth
Green in
Green earth
Blue in
Blue earth
Audio out (L)
Audio out (R)
21
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
CVBS in (video)
RGB status earth
Status RGB
Earth
--Status CVBS
Audio in (L)
Audio earth
Audio in (R)
Suitable inputs for AV1 include
RGB (Red / Green / Blue).
AV3 S-VIDEO 4 pin terminal
Chrominance in
Chrominance earth
Luminance in
Luminance earth
AV2 Scart terminal (VIDEO, S-VIDEO, Q-Link)
Socket Earth
21
CVBS out (video) 19
CVBS earth
17
S.C. - in
15
Earth
13
-11
Earth
9
-7
Earth
5
Audio out (L)
3
Audio out (R)
1
20
18
16
14
12
10
8
6
4
2
CVBS in (video)
Earth
-Earth
-Q-Link data
Status CVBS
Audio in (L)
Audio earth
Audio in (R)
AV2 - Pins 15 and 20 are dependent
on AV2 S-VHS / VIDEO switching.
AV4 Scart terminal (RGB, VIDEO, S-VIDEO, Q-Link)
Socket Earth
21
CVBS out (video) 19
CVBS earth
17
Red in, S.C. - in 15
Red earth
13
Green in
11
Green earth
9
Blue in
7
Blue earth
5
Audio out (L)
3
Audio out (R)
1
20
18
16
14
12
10
8
6
4
2
CVBS in (video)
Earth
Status RGB
Earth
-Q-Link data
Status CVBS
Audio in (L)
Audio earth
Audio in (R)
AV4 - Pins 15 and 20 are dependent
on AV4 S-VHS / VIDEO switching.
38
Specifications
TX-32LXD55F
Power Source
Power Consumption
LCD
Visible screen size
Sound
Speaker
Audio Output
Headphones
Scanning format
Receiving Systems /
Band name
AC 220-240 V, 50 / 60 Hz
Average use : 168 W
Standby condition : 0.4 W (Without Tuner Lock On)
18 W (With Tuner Lock On)
Wide XGA (1,366 × 768 pixels)
16:9 aspect ratio LCD panel
80.0 cmV
697 mm (W) × 392 mm (H)
Woofer φ 8 cm × 2 pcs, Full range φ 5 cm × 2 pcs
20 W (5.4 W + 5.4 W, 4.6 W + 4.6 W)
M3 (3.5 mm) Jack × 1
480i(60Hz), 480p(60Hz), 576i(50Hz), 576p(50Hz), 720p(50Hz), 720p(60Hz), 1080i(50Hz), 1080i(60Hz)
PAL B, G
VHF E2 - E12
UHF E21 - E69
CATV (S01 - S05)
CATV S1 - S10 (M1 - M10)
CATV S11 - S20 (U1 - U10)
CATV S21 - S41 (Hyperband)
PAL 525/60
Playback of NTSC tape from some PAL Video recorders (VCR).
DVB
Digital terrestrial services via VHF / UHF aerial input.
M.NTSC
Playback from M. NTSC Video recorders (VCR).
NTSC (AV input only) Playback from NTSC Video recorders (VCR).
TV signals may not be received in some areas.
This set is only for use in Germany.
Aerial - Rear
Operating Conditions
Connection Terminals
AV1 (Scart connecter)
AV2 (Scart connecter)
AV3
VIDEO
Input
S-VIDEO
AUDIO L - R
AV4 (Scart connecter)
Other
COMPONENT
Inputs
HDMI
AUDIO L - R
Output
AUDIO L - R
Dimensions ( W × H × D )
Including TV Stand
TV Set Only
Weight
UHF / VHF
Temperature : 5 °C - 35 °C
Humidity : 5 % - 90 % RH (non-condensing)
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in)
21 Pin terminal (Audio/Video in, Audio/Video out, S-Video in, Q-Link)
RCA PIN Type × 1
Mini DIN 4-pin
RCA PIN Type × 2
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link)
Y, PB, PR
TYPE A Connecter
RCA PIN Type × 2
RCA PIN Type × 2
795 mm × 635 mm × 300 mm
795 mm × 573 mm × 141 mm
22 kg Net
Note:
Design and Specifications are subject to change without notice. Weight and Dimensions shown are approximate.
Trademark Credits
• DVB is a trademark of the DVB Digital Video Broadcasting Project (1991 to 1996).
• HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
39
Information on Disposal for Users of Waste Electrical & Electronic Equipment
(private households)
This symbol on the products and/or accompanying documents means that used electrical and
electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection
points, where they will be accepted on a free of charge basis. Alternatively, in some countries you
may be able to return your products to your local retailer upon the purchase of an equivalent new
product.
Disposing of this product correctly will help to save valuable resources and prevent any potential negative
effects on human health and the environment which could otherwise arise from inappropriate
waste handling. Please contact your local authority for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further
information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of
disposal.
Trade Mark of the DVB Digital Video Broadcasting Project (1991 to 1996)
TX-32LXD55F Declaration of Conformity No 3587, 31st May 2005
Customer’s Record
The model number and serial number of this product can be found on its rear panel. You should note this serial
number in the space provided below and retain this book, plus your purchase receipt, as a permanent record
of your purchase to aid in identification in the event of theft or loss, and for Warranty Service purposes.
Model Number
Serial Number
Matsushita Electric Industrial Co., Ltd.
Web Site : http://www.panasonic.co.jp/global/
 2005 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.
Printed in Czech Republic
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement