EV-C1303-NMGQ Elite 3X Bullet Camera - Seco-Larm

EV-C1303-NMGQ Elite 3X Bullet Camera - Seco-Larm
EV-C1303-NMGQ
Elite 3X Bullet Camera
Manual
3 Amazing Features. 1 Elite Camera.
WDR
3D-NR Cleans and sharpens
images by reducing camera noise
WDR Captures clean images
even with strong backlight
42 IR LEDs produce a clear
image even in total darkness
ENFORCER Elite 3X Bullet Camera
Features:







1000 TV Lines
Megapixel CMOS
Built-in service monitor port
Weatherproof (IP67) for outdoor use
DC Auto iris varifocal lens with ICR (IR Cut Filter)
WDR (Wide Dynamic Range) provides clear
images under intense backlight conditions
Intelligent features such as motion detection and
zoom control





32x DSS (Digital Slow Shutter) amplifies
existing light to capture images in almost total
darkness
3-Axis mounting arm
12VDC/24VAC Operation
OSD (On-Screen Display) for convenient
programming of special features
Defog to improve image clarity in poor
conditions
Specifications:
Model
Type
CMOS
Resolution
Video output format
Effective pixels
3D-NR
WDR
OSD Control
Scanning system
Sync
Video output format
Lens
# of IR LEDs
IR Range
Minimum illumination
Gamma correction
S/N Ratio
DSS (Digital Slow Shutter)
Shutter control
Gain control
White balance
Operating voltage
LEDs OFF
Current
draw
LEDs ON
IP Rating
Operating temperature
Dimensions
Cable length
Weight
Parts List:
1x Camera
1x Mounting plate
1x Rubber grommet
1x DC Plug with terminal block
1x Service monitor port connector
4x Mounting screws
4x Hex screws
1x Hex wrench
1x Manual
1x Zoom/focus adjustment tool
2
EV-C1303-NMGQ
Bullet
1/ ” 1.3MP Sony IMX138
3
1000 TV Lines
NTSC
1305x1049 pixels
Yes
Yes
Yes
Progressive scan
Internal
1.0Vp-p Composite video, 75Ω
2.8~12mm
42
Up to 100’ (30m)
0 Lux (IR LEDs on)
Yes
>50dB
32x
Auto Electric Shutter (AES), 1/60~1/60,000 s
Auto
Auto
12VDC/24VAC
[email protected]
[email protected]
IP67
-14°~122° F (-10~50° C)
315/16”x315/16”x81/4” (100x100x210 mm)
5’10” (1.8m)
3-lb 1.4-oz (1,400g)
Dimensions:
81/4” (210mm)
215/16”
(75mm)
315/16”
(100mm)
45/16”
(110mm)
SECO-LARM U.S.A., Inc.
ENFORCER Elite 3X Bullet Camera
Overview:
Sunshield
Mounting Rubber
plate grommet
Sunshield screw
Mounting arm
adjustment screw
Female BNC
connector
DC Plug with
terminal block
Mounting arm
Camera angle
adjustment screw
DC Jack
Adjustment nut
3-Axis Mounting Bracket:
Zoom/focus
lock
Zoom
Focus
IR LED
Service
monitor port
OSD
joystick
The camera angle adjustment
screw, mounting arm adjustment
screw, and adjustment nut can
be loosened to adjust the
camera’s position.
2
1
3
Before Starting:
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not aim the LED light directly at the eyes when the
LEDs are on.
4. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong electrical
signals.
6. Do not open or disassemble the camera. There are
no field-serviceable parts inside.
7. Do not drop the camera or subject it to strong
vibrations.
Installation:
1. Run a 12VDC/24VAC power supply wire and a video
cable with a male BNC connector through the wall to
where the camera is to be mounted.
2. Temporarily connect the camera to the power supply.
Do not cut the DC jack or female BNC plug as
warranty will be voided. If needed, use the included
DC plug with terminal block.
3. Connect a test monitor to the service monitor port using
the included service monitor port connector.
4. While watching the monitor, hold the camera against
the wall or ceiling by hand where it is to be mounted,
then adjust the camera angle until it is certain that the
mounting location is correct. See “3-Axis Mounting
Bracket” above. Use a pencil to mark the location of the
four screw holes in the mounting plate.
5. Disconnect the power supply and test monitor.
6. Mount the mounting plate and rubber grommet to the
SECO-LARM U.S.A., Inc.
wall or ceiling using the included mounting screws.
If the wall is made of drywall, brick, or similar
material, it may be necessary to use screw anchors
(not included).
7. Mount the camera base to the mounting plate using
the included hex screws.
8. Connect the female BNC connector and DC jack to
the male BNC connector and power supply wire run
in Step 1.
9. Adjust the zoom and focus by adjusting the knobs on
the bottom of the camera with a small screwdriver.
When finished, twist the “Lock” knob to lock the
settings into place.
10. Use the OSD joystick to adjust the camera settings
(see OSD manual).
11. Do a final test of the camera and monitor.
3
ENFORCER Elite 3X Bullet Camera
Troubleshooting:
The screen is blank.




Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
The screen image is dim.
 Clean the lens using a soft, clean cloth.
 Check that the light source is adequate.
The screen image has poor contrast.
 Adjust the monitor’s contrast knob.
 Change the position of the camera.
The screen image flickers.
 Change the position of the camera.
The screen image is distorted.
 Change the position of the camera.
The camera case is hot.
 Check that the correct power supply is in use.
IR LEDs do not turn on.
 Check that the correct power supply is in use.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws
and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the
use of this product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do
not open the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if
damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of
SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property
damage of any kind to the purchaser or anyone else.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to
change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2014 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
SECO-LARM® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Phone: (949) 261-2999 | (800) 662-0800
4
PIKHR1
Website: www.seco-larm.com
MiEV-C1303NMGQ_141107.docx
Email: [email protected]
SECO-LARM U.S.A., Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement