safe sleeper™bed rail 1 2 4 3

safe sleeper™bed rail 1 2 4 3
#BR36
safe sleeper bed rail
™
READ ALL INSTRUCTIONS BEFORE FIRST USE.
Ages 2 Years – 6 Years
CAUTION: ADULT ASSEMBLY REQUIRED.
WARNING: IMPORTANT! KEEP FOR FUTURE REFERENCE!
• SUFFOCATION AND STRANGULATION HAZARD.
• Gaps in and around bed rails have entrapped young children and killed
infants.
• NEVER use with children younger than 2 years old. Use ONLY with older
children who can get in and out of adult bed without help. NEVER use in
place of crib.
• NEVER use unless bed rail is tight against mattress, without gaps, and at
least 9 in. from headboard and footboard. Do not fill gaps with pillows,
blankets, or other items that can suffocate children.
• NEVER use on toddler bed, bunk bed, waterbed, or bed with inflatable
mattress. Use ONLY on adult bed.
• Discontinue use if damaged, broken, or if parts are missing.
ASSEMBLY INSTRUCTIONS
Please follow these four easy steps to assemble this rail very quickly and WITHOUT TOOLS!
Figure B
Figure A
1
Lay the 2 halves of the rail on the floor or table, so that the 3 Cross
Bars line up (Figure A). NOTE: Make sure Anchor Straps are not
twisted.
2
Connect the 3 Cross Bars by pressing them firmly into place
(Figure B).
Figure C
3
Slide Mesh Cover across the entire rail (Figure C),
then zip it closed (Figure D).
Figure D
Figure E
4
Open Hinged Legs until hinges lock firmly into place (Figure E).
Assembly is now complete. Proceed to installation instructions.
INSTALLATION AND USE INSTRUCTIONS FOR BEDS WITH BOX SPRINGS
01. Extend Anchor Strap and Plate to maximum length.
02. Insert Hinged Legs into place between mattress and box spring.
mattress
03. Extend Anchor Strap and Plate so that Anchor Plate is in position for
tightening. (Figure F)
04. Pull red striped tag toward you while pushing the Anchor Plate forward with
opposite hand, pressing Anchor Plate firmly against the mattress and box
spring. (Figure G)
05. Release grip on the red striped tag and pull the lower strap toward you until
Anchor Plate is snug against mattress and box spring. (Figure H)
IMPORTANT: To insure bed rail is tight as possible against mattress and
box spring, raise the mattress and tighten the strap slightly. Then lower the
mattress and pull the anchor plate back and firmly into place. Repeat this
step as needed and until tight.
e
lat
rp
o
ch
an
box spring
Figure F
06. Tuck remaining length of strap under the mattress, out of the way of children.
07. Lowering rail after installed on bed: This rail is designed with childproof
hinges for added safety. Therefore – to lower your rail - you must raise EACH
(both left and right) spring-loaded hinge at the same time. The hinges each
display an arrow pointing upwards in the direction you must raise the hinge to
disengage it. Once each spring is raised, you may gently lower the rail with
ease. This will allow you to easily change or make the bed. When you raise
the rail back to the upright position, the locks will automatically pop back into
place for safety.
Figure G
Figure H
CLEANING INSTRUCTIONS
Machine wash cold and hang dry, or surface wash with damp cloth.
DEX Products, Inc. www.dexbaby.com 800.546.1996 840A Eubanks Drive, Vacaville, CA 95688
© 2012 DEX Products, Inc., dexbaby™, safe sleeper™, and the footprint logo are trademarks of DEX Products, Inc. safe sleeper™ bed rail is protected by
U.S. patent number 6,990,697 which is strictly monitored and enforced. Patent infringement will be prosecuted to the full extent of the law. Made in China. 0412
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement