Alpine | USA264 | Use and Care Manual | Alpine USA264 Use and Care Manual

Limited Warranty Information
Thank you for choosing an Alpine product! We aim to please with our wide range of products
including Fountains, Birdbaths, Statuary, Pond Supplies & More. All of our products are constructed
from the highest quality materials. In the event that we have not achieved our usual standard of
excellence, we will repair or replace, at our discretion, within the warranty period. A valid proof of
purchase, with the purchase date clearly indicated, must be provided. Photos of defective
merchandise will also be required to help distinguish the actual cause of the defect. Please read
below for a detailed description of warranty coverage.
Water Damage
Alpine products are not manufactured to withstand extreme temperatures. Improper
storage that allows water to freeze within a product may cause damage and is considered
negligence and will, therefore not be covered under this warranty. The use of “hard water”
and/or caustic cleaners can affect the paint or other finishes. Failure to keep the unit clean,
and use of such additives/cleaners, will also void the warranty. Please note: for fountains,
it is normal for some splashing to occur and protecting the immediate surfaces is not the
responsibility of Alpine Corporation
Paint & Color (Retention and/or Loss)
The use of water will cause natural erosion to the color. This area can be touched up
using standard paint. The paint is designed to protect the entire finish against breakdown
of color. As with any product, all finishes with time will gradually fade and discolor. The
warranty will only cover against severe or complete fading within the first year from date of
purchase with the above exclusion.
Should a warranty/claim be needed, you should contact the retailer from whom you
purchased the product. If that is not an option, you can contact Alpine Corporation at When contacting Alpine Corporation, you must be prepared to
show proof of purchase, provide photographs and any other information needed to
validate your claim. This may be necessary to distinguish between a partial or complete
replacement of a defective product. The warranty does not cover any items with multiple
parts; the warranty will ONLY cover the individual component of the unit/item that may be
defective. Replacement parts can be made available to a consumer through the original
selling party, or an approved parts retailer. If this is not an option, contact our customer
service department.
Not Covered Under Warranty
The limited warranty will NOT cover cases of damages due to
1. Damages caused in Transit
2. Inadequate care and/or neglect
3. Environmental and/or natural elements
4. Immersion in water, unless specified
5. Improper Installation/Storage and/or Maintenance
This warranty is void if the product has been damaged by accident, misuse, negligence, improper
installation and/or modifications have occurred. This includes any and/or all defects arising out of
freezing water damage, hard water damage, failure to keep the unit clean and free of harmful
additives such as bleach, chlorine, etc…. which affects the paint and/or parts. This warranty also
does not cover any additional charges or installation, removal, disposal and/or shipping costs or
consequential damage associated with any warranty claim
Lotus Tiering Fountain
Assembling & Using Your Product
Trouble Shooting & Caution
Unpack all components carefully. Please check to ensure all parts have been
removed from the packaging. Some splashing may occur.
If you have any questions and/or problems, please contact the retail store you
purchased this fountain.
Fountain Top Piece
Fountain Middle Piece
Fountain Bottom Piece
Fountain Stand
Submersible Pump
If your pump fails to run
If your pump “spews”
 Check the water level to make sure the pump is completely submerged and
there if enough water in the basin to operate your fountain. Not having enough
water will cause your pump to spew
If your pump is making abnormal loud noises
 Disconnect the pump from the electrical power supply and remove the front
Feed the pump cord down through the center of the fountain stand.
Place fountain bottom piece on top of fountain stand and twist to tighten.
Place fountain middle piece on top of fountain bottom piece. Feed the
tubing connected to the top piece through the center of the middle
fountain piece. Twist top piece to middle piece to tighten. (step 2)
Connect the vinyl tubing to the water pump in the bottom dish. Adjust the
flow control to the lowest setting to avoid splashing until the fountain is
completely assembled. (step 3)
Gently pour water into the fountain, being careful not to overflow and
cause splashing. Make sure the water completely submerges the pump
and the water flows smoothly during operation. (step 4)
Plug into your local power supply. Make sure that there is no water
around the transformer and always keep the power source in a dry
place. (step 5)
NOTE: We recommend that you use distilled water to prevent
scale build-up. The first time you operate the pump it can take
up to 5 minutes for the air to be completely expelled and water
begins to flow properly.
Check the circuit breaker or try a different outlet to make sure the pump is
receiving electrical power.
Check the pump discharge and tubing for any kinks and/or obstructions
Any buildup obstructing the water flow can be flushed with a garden hose
Check the rotor by removing the front cover & plate to access the impellor area.
Turn the rotor and make sure that the rotor is not jammed or broken
cover & plate
Carefully grip the impeller and gently pull the impeller/rotor assembly out of the
pump housing
Rinse the impeller/rotor assembly and clean the cavity with clean water. If
breakage or damage is found, contact your local retailer for part
Fountain Care
We recommend to use Alpine’s all natural cleansing formula to eliminate foam,
lime scale and calcium buildup, fight mineral deposits, leave water crystal clear,
help prevent staining, remove organic contaminants and treat discolored water.
This formula will help prevent pump damage due to hard water build up.
i. For small sized fountains holding water up to 7liters of water, we
recommend Alpine Item # PPL100
ii. For larger sized fountains holding water over 7liters of water, we
recommend Alpine Item # PPL102
iii. For more information please visit
o Always unplug the pump from the electrical outlet before
cleaning & handling
o Uses with clean water only, do not place the fountain and/or
parts in any other liquid.
o Periodically change water & clean the pump to keep free
from micro-organisms
o Disconnect and store the unit in a dry place if not in use for
an extended period of time
o Do not operate with water above 90°F or 30°C
o Do not lift, carry or pull the pump by the power cord
o Do not exceed the maximum voltage & wattage on
Download PDF