ALTEC ATP 4200, ATP 4300, ATP 4600 Thermal Transfer Barcode Printer User’s Manual
Below you will find brief information for Thermal Transfer Barcode Printer ATP 4200, Thermal Transfer Barcode Printer ATP 4300, Thermal Transfer Barcode Printer ATP 4600. The printer is designed with die-casting aluminum chassis and print mechanism with metal cover and large clear media view window, ensuring it is suitable for tough industrial environments. It offers various features including a graphic LCD display, moveable sensor design for wide label range, and support for various bar code formats. It integrates high performance MONOTYPE IMAGING® True Type font engine and customizable fonts for printing labels.
Advertisement
Advertisement
ATP-4200
ATP-4300
ATP-4600
THERMAL TRANSFER / DIRECT THERMAL
BAR CODE PRINTER
USER’S
MANUAL
ALTEC industrial identification altec.nl | altec.be
Copyright Information
The copyright in this manual, the software and firmware in the printer described therein are owned by the company. All rights reserved.
CG Triumvirate is a trademark of Agfa Corporation. CG Triumvirate Bold
Condensed font is under license from the Monotype Corporation. Windows is a registered trademark of Microsoft Corporation.
All other trademarks are the property of their respective owners.
Information in this document is subject to change without notice and does not represent a commitment on the part of the company. No part of this manual may be reproduced or transmitted in any form or by any means, for any purpose other than the purchaser’s personal use, without the expressed written permission of the company.
ALTEC industrial identification
1 altec.nl | altec.be
Agency Compliance and Approvals
CE CLASS A
EN 55022:2006 +A1:2007
EN 55024:1998+A1:2001+A2:2003
EN 61000-4 SERIES REQULATIONS
FCC CFR Title 47 Part 15 Subpart B:2010-Section 15.107 and 15.109
ICES-003 Issue 4:2004 Class A
AS/NZS CISPR 22:2009
CLASS A
GB-4953-2001
GB9254-2008 (CLASS A)
GB17625.1-2003
此为
A 级产品,在生活环境中,该产品可能会造成无线电干扰,在这种情况下,
可能需要用户对干扰采取切实可行的措施。
UL 60950-1(2nd Edition)
CSA C22.2 No. 60950-1-07(2nd Edition)
CAUTION
1. HAZARDOUS MOVING PARTS IN CUTTER MODULE. KEEP FINGER AND OTHER
BODY PARTS AWAY.
2. THE MAIN BOARD INCLUDES REAL TIME CLOCK FEATURE HAS LITHIUM BATTERY
CR2032 INSTALLED. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN
INCORRECT TYPE.
3. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER
INSTRUCTIONS.
EN 60950-1/A1:2010
IEC 60950-1/A1:2009
IEC 60950-1:2005(2nd Edition)
ALTEC industrial identification
2 altec.nl | altec.be
Contents
1. Introduction ............................................ 1
1.2.1 Printer standard features .............................................................. 2
1.2.2 Printer optional features ............................................................... 3
2. Operations Overview ..................................... 9
2.3.1 Front Panel Display ..................................................................... 14
2.3.3 Front Panel Keys ......................................................................... 15
2.5.1 Loading Ribbon ........................................................................... 16
2.5.2 Remove Used Ribbon .................................................................. 19
2.6.1 Loading the Media ....................................................................... 20
2.6.2 Loading Fan-fold Labels ............................................................. 24
2.6.3 Loading Media in Peel-off Mode (Option) .................................. 26
2.6.4 Remove Liner from Internal Rewind (Option) ............................ 28
2.6.5 Loading Media in Rewind Liner with Label Mode (Option) ...... 29
2.6.6 Remove Labels from Internal Rewind (Option) ......................... 31
2.7.1 Print head Pressure Adjustment Knob ...................................... 32
2.7.2 Print Head Burn Line Adjustment Knob..................................... 32
2.8 Using the Keyboard with PS/2 ............................................................ 34
ALTEC industrial identification i altec.nl | altec.be
3. Menu Function ......................................... 35
3.1.1-1 Printer Setup (TSPL2) ............................................................... 37
3.1.1-2 Printer Setup (ZPL2) ................................................................. 44
4. Diagnostic Tool ......................................... 74
4.2 Printer Function (Calibrate sensor, Ethernet setup, RTC setup………)
5 Setting Ethernet by Diagnostic Utility...................................................... 76
5.1 Using USB interface to setup Ethernet interface ................................ 76
5.2 Using RS-232 interface to setup Ethernet interface ............................ 77
5.3 Using Ethernet interface to setup Ethernet interface ......................... 78
6. Troubleshooting ........................................ 80
6.2 Mechanism Fine Adjustment to Avoid Ribbon Wrinkles .................... 84
7. Maintenance ........................................... 86
Revise History ........................................... 88
ALTEC industrial identification ii altec.nl | altec.be
1. Introduction
1.1 Product Introduction
Thank you very much for purchasing the bar code printer.
This printer is designed with die-casting aluminum chassis and print mechanism, metal cover with large clear media view window, which ensuring to work for the extreme and heavy duty industrial environment and applications.
With back-lit graphic LCD display, printer status can be managed easier and operated more user friendly. The moveable sensor design can accept wide range of label media.
All of the most frequently used bar code formats are included. Fonts and bar codes can be printed in any one of the four directions.
This printer is built-in the high quality, high performance MONOTYPE IMAGING® True
Type font engine and one CG Triumvirate Bold Condensed smooth font. With flexible firmware design, user can also download the True Type Font from PC into printer memory for printing labels. Besides the scalable font, it also provides a choice of five different sizes of alphanumeric bitmap font, OCR-A and OCR-B fonts. By integrating rich features, it is the most cost-effective and high performance printer in its class!
Applications o
Industrial-duty printing o o
Healthcare patient safety
Compliance labeling o o o o o o
Work in process
Order fulfillment
Distribution
Shipping/ receiving
Ticketing
Electronics & jewelry labeling
ALTEC industrial identification altec.nl | altec.be
1.2 Product Features
1.2.1 Printer standard features
The printer offers the following standard features.
Product standard feature
Thermal transfer printing
Direct thermal printing
High quality die-cast aluminum design
Metal cover with large clear media view window
Moveable gap sensor (position full web adjustable)
Moveable black mark sensor (position full web adjustable)
Ribbon end sensor
Head open sensor
LCD display (graphic type, 128x64 pixel) with back light
Control panel with 6 operation buttons
Control panel security (TCF)
LED indicators
Real time clock
Internal Ethernet print server (10/100 Mbps) interface
USB 2.0 (full speed) interface
Serial RS-232C (2400-115200 bps) interface
Centronics (SPP mode) interface
PS/2 keyboard interface for stand-alone or data entry at print site
32 MB SDRAM memory
203 dpi models
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
300 dpi models
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
600 dpi models
○
○
○
○
○
○
○
○
○
○
8 MB FLASH memory
SD FLASH card memory expands storage to 4 GB
Powerful 32 bit 200 MHz RISC processor
Standard industry emulations right out of the box including Eltron
®
and Zebra
®
language support
ALTEC industrial identification
2
○
○
○
○
○
○
○
○
○
○
○
○ altec.nl | altec.be
Internal 8 alpha-numeric bitmap fonts
Fonts and bar codes can be printed in any one of the four directions (0, 90,180, 270 degree)
Internal Monotype Imaging
®
true type font engine with one CG Triumvirate Bold Condensed scalable font
Downloadable fonts from PC to printer memory
Text, bar code, graphics/image printing (Please refer to the TSPL/TSPL2 programming manual for supporting code page)
Support Bar Code
1D bar code
Code 39,
Code 93,
Code128UCC,
Code128 subsets A.B.C,
Codabar,
Interleave 2 of 5, EAN-8,
EAN-13,
EAN-128,
UPC-A,
UPC-E,
EAN and UPC 2(5) digits add-on,
MSI,
PLESSEY,
POSTNET,
China POST,
RSS-14,
Code 11
2D bar code
PDF-417,
Maxicode,
DataMatrix,
QR code,
Aztec
Support image
BITMAP,
BMP,
PCX
○
○
○
○
○ ○
○
○
○
○
○
○
○
○
○
1.2.2 Printer optional features
1.2.2-1 Industrial model
The printer offers the following optional features.
Product option feature
User options
Applicator I/O interface
USB Host
Peel-off kit
(include liner rewind spindle and peel off sensor)
-
-
-
Dealer options
-
-
○
Factory options
○
○
-
ALTEC industrial identification
3 altec.nl | altec.be
Internal rewind kit
(include label rewind spindle and label redirect kit)
Regular guillotine cutter
(Paper thickness: 0.06~ 0.19mm, 500,000 cuts;
0.20~ 0.25mm, 200,000 cuts)
Heavy duty cutter module
(Paper thickness: Max 0.25 mm/ Max. paper weight <200g/ m
2
, 1,000,000 cuts; <300g/m
2
,
500,000 cuts)
Care label cutter
(Paper thickness: Max. 0.15mm, 400,000 cuts)
KP-200 Plus keyboard display unit
KU-007 Plus programmable smart keyboard display unit
HCS-200 long rang CCD scanner
-
○
○
○
○
○
○
○
-
-
-
-
-
-
-
-
-
-
-
-
-
Note: Except for the linerless cutter, all regular/heavy duty/care label cutters DO NOT cut on media with glue.
ALTEC industrial identification
4 altec.nl | altec.be
1.3 General Specification
General Specifications
Physical dimensions 270 mm (W) x 308 mm (H) x 505 mm (D)
Weight
Electrical
15 kg (33.1 lb)
Internal switching power supply
Input: AC 100-240V, 2A,
50-60Hz Output: DC 24V, 5A,
120W
Environmental condition Operation: 5 ~ 40˚C (41 ~ 104˚F), 25~85% non-condensing
Storage: -40 ~ 60 ˚C (-40 ~ 140˚F), 5~90% non-condensing
1.4 Print Specifications
Specifications
203 dpi models
Print head resolution 203 dots/inch
ALTEC industrial identification
5
300 dpi models
300 dots/inch
600 dpi models
600 dots/inch altec.nl | altec.be
Printing method
Dot size
(width x length)
Print speed
(inches per second)
Max. print width
Max. print length
Printout bias
(8 dots/mm) (12 dots/mm) (24 dots/mm)
Thermal transfer and direct thermal
0.125 x 0.125 mm 0.084 x 0.084 mm 0.042 x 0.042 mm
(1 mm = 8 dots) (1 mm = 12 dots) (1 mm = 24 dots)
2, 3, 4, 5, 6, 7, 8, 10,
11, 12 ips selectable
Up to 12 ips
2, 3, 4, 5, 6, 7, 8 ips selectable
Up to 8 ips
2, 3, 4 ips selectable
Up to 4 ips
4064 mm (160”)
104 mm (4.09”)
1854.2 mm (73”) 1016 mm (40”)
Vertical: 1 mm max.
Horizontal: 1 mm max.
1.5 Ribbon Specifications
Ribbon Specifications
Ribbon outside diameter
Ribbon length
Ribbon core inside diameter
Ribbon width
ALTEC industrial identification
6
90 mm
600 meter
1 inch (25.4 mm)
Max. 114.3 mm (4.5”) altec.nl | altec.be
Ribbon wound type
Ribbon end type
Min. 25.4 mm (1.0”)
Ink coated outside wound, ink coated inside wound
Transparency
1.6 Media Specifications
Media Specifications 203 dpi models 300 dpi models 600 dpi models
Label roll capacity 208.3 mm (8.2”)
Media alignment Edge alignment
Media type
Media wound type
Continuous, die-cut, black mark, fan-fold, notch
Printing face outside wound
Media width
(label + liner)
Max. 118 mm (4.6”)
Min. 25.4 mm (1.0”)
Media thickness
(label + liner)
Media core diameter
Label length
Label length
(peeler mode)
Label length
(cutter mode)
Gap height
Black mark height
Black mark width
Max. 0.30 mm (11.8 mil)
Min. 0.06 mm (2.36 mil)
Max. 76.2 mm (3”)
Min. 25.4 mm (1”)
Max. 4,064 mm (160”) Max. 1,854 mm (73”) Max. 1016 mm (40”)
Min. 5 mm (0.20”) Min. 5 mm (0.20”) Min. 5 mm (0.20”)
Max. 152.4 mm (6”)
Min. 25.4 mm (1”)
Max. 4,064 mm (160”) Max. 1,854 mm (73”) Max. 1016 mm (40”)
Min. 25.4 mm (1”) Min. 25.4 mm (1”) Min. 25.4 mm (1”)
Min. 2 mm
Min. 2 mm
Min. 8 mm (0.31”)
ALTEC industrial identification
7 altec.nl | altec.be
ALTEC industrial identification
8 altec.nl | altec.be
2. Operations Overview
2.1 Unpacking and Inspection
This printer has been specially packaged to withstand damage during shipping.
Please carefully inspect the packaging and printer upon receiving the bar code printer.
Please retain the packaging materials in case you need to reship the printer.
Unpacking the printer, the following items are included in the carton.
One printer unit
One Windows labeling software/Windows driver CD disk
One quick installation guide
One power cord
One USB interface cable
If any parts are missing, please contact the Customer Service Department of your purchased reseller or distributor.
ALTEC industrial identification
9 altec.nl | altec.be
2.2 Printer Overview
2.2.1 Front View
1
2
3
4
5
1. LED indicators
2. LCD display
3. Front panel buttons
4. Paper exit chute
5. Lower front cover
6. Printer right side cover
6
ALTEC industrial identification
10 altec.nl | altec.be
2.2.2 Interior view
1
2
3
4
7
8
9
10
5
6
1. Ribbon rewind spindle
2. Ribbon release button
3. Ribbon guide plate
4. Print head
5. Platen roller
6. Print head release lever
7. Media guide bar
8. Label roll guard
13
14
15
9. Label supply spindle
10. Ribbon supply spindle
11. Damper
12. Media sensor lock lever
16
13. Z axis mechanism adjustment knob
14. Print head pressure adjustment knob
15. Anti-static brush
16. Ribbon sensor
17. Media sensor
18. Label guide
ALTEC industrial identification
11
17
17
1.
12
11
18
altec.nl | altec.be
2.2.3 Rear View
1
2
3
4
5
1. Fan-fold paper entrance chute
2. Centronics interface
3. USB interface
4. RS-232C interface
5. Power jack socket
6. GPIO interface (Option)
*7. SD card slot
8. Ethernet interface
9. USB host (Option)
10. PS/2 interface
11. Power switch
Note:
1. SD card slot, Ethernet interface and PS/2 interface are standard interfaces
2. GPIO interface card includes SD card slot, Ethernet and PS/2 interfaces. So GPIO interface is an factory option
6
7
8
9
10
11
Note:
The interface picture here is for reference only. Please refer to the product specification for the interfaces availability.
ALTEC industrial identification
12 altec.nl | altec.be
* Recommended SD card specification.
SD card spec SD card capacity
V1.0, V1.1 128 MB
Approved SD card manufacturer
SanDisk, Transcend
V1.0, V1.1 256 MB SanDisk, Transcend, Panasonic
V1.0, V1.1
V1.0, V1.1
512 MB
1 GB
V2.0 SDHC CLASS 4 4 GB
SanDisk, Transcend, Panasonic
SanDisk, Transcend, Panasonic
V2.0 SDHC CLASS 6 4 GB
V1.0, V1.1
SanDisk, Transcend, Panasonic microSD 128 MB Transcend, Panasonic
V1.0, V1.1
V1.0, V1.1
V1.0, V1.1 microSD 256 MB Transcend, Panasonic microSD 512 MB Panasonic microSD 1 GB Transcend, Panasonic
V2.0 SDHC CLASS 4 microSD 4 GB
V2.0 SDHC CLASS 6 microSD 4 GB
V1.0, V1.1
V1.0, V1.1
Panasonic
Transcend miniSD 128 MB Transcend, Panasonic miniSD 256 MB Transcend, Panasonic
V1.0, V1.1
V1.0, V1.1 miniSD 512 MB Transcend, Panasonic miniSD 1 GB Transcend, Panasonic
V2.0 SDHC CLASS 4 miniSD 4 GB
V2.0 SDHC CLASS 6 miniSD 4 GB
Transcend
- The DOS FAT file system is supported for the SD card.
- Folders/files stored in the SD card should be in the 8.3 filename format
- The miniSD/microSD card to SD card slot adapter is required.
ALTEC industrial identification
13 altec.nl | altec.be
2.3 Operator Controls
2.3.1 Front Panel Display
LED indicators
LCD display
Front panel buttons
2.3.2 LED Indicators
LED Status
Off
On
On
Blinking
Off
On
Blinking
Indication
The printer power is turned off
The printer power is turned on
Printer is ready
Pause
Downloading data into printer.
Printer is ready
“CARRIAGE OPEN” or “CUTTER ERROR”
“NO PAPER”, “PAPER JAM”, “NO RIBBON” or “CLEAN DATA”
ALTEC industrial identification
14 altec.nl | altec.be
2.3.3 Front Panel Keys
Keys Function
1. Enter the menu
2. Exit from a menu or cancel a setting and return to the previous menu
Pause/Resume the printing process
Advance one label
Scroll up the menu list
Scroll down the menu list
Enter/Select cursor located option
2.4 Setting Up the Printer
1. Place the printer on a flat, secure surface.
2. Make sure the power switch is off.
3. Connect the printer to the computer with the provided USB cable.
4. Plug the power cord into the AC power cord socket at the rear of the printer, and then plug the power cord into a properly grounded power outlet.
Note:
Please switch OFF printer power switch prior to plug in the power cord to printer power jack.
ALTEC industrial identification
15 altec.nl | altec.be
2.5 Loading Ribbon
2.5.1 Loading Ribbon
1. Open the printer right side cover.
2. Push the print head release lever to open the print head mechanism.
3. Install the ribbon onto the ribbon supply spindle.
ALTEC industrial identification
16 altec.nl | altec.be
4. Thread the ribbon through the ribbon sensor slot and then through the open space in between print head and platen.
Ribbon
Ribbon sensor
5. Wrap the ribbon onto the ribbon rewind spindle. Wind the ribbon clockwise about 3~5 circles onto the ribbon rewind spindle until it is smooth and properly stretched.
Note: Please DO NOT push the ribbon release button when you are loading the ribbon. The ribbon release button is used to remove the used ribbon.
( Please refer to section 2.5.2
)
6. Close the print head mechanism,
Make sure the latches are engaged securely.
ALTEC industrial identification
17 altec.nl | altec.be
Loading path for ribbon
ALTEC industrial identification
18 altec.nl | altec.be
2.5.2 Remove Used Ribbon
1. Break the ribbon between ribbon guide plate and the ribbon rewind spindle.
2. Push the ribbon release button to release the ribbon on the ribbon rewind spindle.
3. Then, slide off the ribbon from ribbon rewind spindle.
ALTEC industrial identification
19 altec.nl | altec.be
2.6 Loading the Media
2.6.1 Loading the Media
1. Open the printer right side cover.
2. Push the print head release lever to open the print head mechanism.
3. Move the label roll guard horizontally to the end of label spindle then flip down the label roll guard.
ALTEC industrial identification
20 altec.nl | altec.be
4. Place the roll of media on the label supply spindle. Flip up the label roll guard. Move the label roll guard horizontally to gently fit the width of label roll.
3” Label spindle 1” Label spindle
Note: Replace 3” label supply spindle to fit the 1” core label by removing two screws.
5. Pull label roll leading edge forward through the media guide bar, damper, media sensor and place the label leading edge onto the platen roller.
Media guide bar
Media sensor
Label guide
Damper
ALTEC industrial identification
21 altec.nl | altec.be
6. Unlock the media sensor lock lever to adjust the media sensor.
Lock
Unlock
Gap label Black mark label
* The sensor location is marked by a triangle mark
▽
at the sensor housing.
* The media sensor position is moveable, please make sure the gap or black mark is at the location where media gap/black mark will pass through for sensing.
7. Adjust the label guide to fit the width of the label.
ALTEC industrial identification
22 altec.nl | altec.be
8. Close the print head mechanism. Make sure the latches are engaged securely.
9. Using the front display panel, set the media sensor type and calibrate the selected sensor. (Please refer to section 3.1.2)
Note: Please calibrate the gap/black mark sensor when changing media.
Loading path for roll labels
ALTEC industrial identification
23 altec.nl | altec.be
2.6.2 Loading Fan-fold Labels
Fan-fold media feeds through either the bottom or rear external label entrance chute.
1. Open the printer right side cover.
2. Push the print head release lever to open the print head mechanism.
3. Insert the fan-fold media through the bottom or rear external label entrance chute.
4. Pull fan-fold label leading edge forward through the media guide bar, damper media sensor and place the label leading edge onto the platen roller.
5. Adjust the label guide by sliding to fit the paper width.
6. Close the print head mechanism. Make sure the latches are engaged securely.
7. Set the media sensor type and calibrate the selected sensor. (Please refer to section
3.1.2)
Note: Please calibrate the gap/black mark sensor when changing media.
Loading path for fan-fold labels
ALTEC industrial identification
24 altec.nl | altec.be
ALTEC industrial identification
25 altec.nl | altec.be
2.6.3 Loading Media in Peel-off Mode (Option)
1. Open the printer right side cover.
2. Push the print head release lever to open the print head mechanism.
3. Move the label roll guard horizontally to the end of label spindle then flip down the label roll guard.
4. Place the roll of media on the label supply spindle. Flip up the label roll guard. Move the label roll guard horizontally to fit the width of label roll.
5. Pull label roll leading edge forward through the media guide bar, damper media sensor and place the label leading edge onto the platen roller.
6. Adjust the label guide to fit the width of the label.
7. Using the front display panel, set the media sensor type and calibrate the selected sensor. (Please refer to section 3.1.2)
8. Then, pull approximately 650mm of label through the front of the printer.
9. Push down the peel-off roller release lever.
Peel-off roller release lever
10. Feed the label between peel-off roller and platen roller.
ALTEC industrial identification
Peel-off roller
26 altec.nl | altec.be
11. Wrap the label onto the internal rewind spindle and wind the spindle counter-clockwise about 3~5 circles until the label is properly stretched.
12. Lift up the peel-off roller release lever and close the print head mechanism.
13. Move the peel-off sensor toward the paper exit chute.
Peel-off sensor
14. Peeling will automatically start. Press the FEED button to test.
Label
Liner
Note: Please calibrate the gap/black mark sensor when changing media.
ALTEC industrial identification
27 altec.nl | altec.be
2.6.4 Remove Liner from Internal Rewind (Option)
1. Break the liner between peel-off roller and the internal rewind spindle.
2. Push the liner release button to release the liner on the internal rewind spindle.
3. Then, slide off the liner from internal rewind spindle.
ALTEC industrial identification
28 altec.nl | altec.be
2.6.5 Loading Media in Rewind Liner with Label Mode (Option)
This mode can rewind the media including liner and label on the rewind spindle.
1. Open the printer right side cover.
2. Insert the supply holder guide and paper core into the internal rewind for 1” core label roll.
Insert the supply holder guide, 3” label core adapter and paper core into the internal rewind for 3” core label roll.
1” core label roll 3” core label roll
Supply holder guide
Paper core
Supply holder guide
Paper core
3” label core adapter
3. Insert media into the printer label spindle. Pull label roll leading edge forward through the media guide bar, damper media sensor and place the label leading edge onto the platen roller. (Please refer to section 2.6.1)
4. Then, pull approximately 650mm of label through the label redirect front panel.
5. Wrap the label onto the internal rewind spindle and stick the label onto the paper core.
ALTEC industrial identification
29 altec.nl | altec.be
6. Insert another supply holder guide into the internal rewind for 1” core label roll.
Supply holder guide
7. Using the LCD panel to set the media sensor type and calibrate the selected sensor. (Please refer to section 3.1.2)
Note: Please calibrate the gap/black mark sensor when changing media.
ALTEC industrial identification
30 altec.nl | altec.be
2.6.6 Remove Labels from Internal Rewind (Option)
1. Slide off the labels with supply holder guides from internal rewind spindle.
Supply holder guides
ALTEC industrial identification
31 altec.nl | altec.be
2.7 Adjustment Knob
2.7.1 Print head Pressure Adjustment Knob
Print head pressure adjustment knobs
The print head pressure adjustment knob
has 5 levels of adjustment. Because the printer’s paper alignment is to the left side of mechanism, different media widths require different pressure to print correctly. Therefore it may require to adjust the pressure knob to get your best print quality. For example, if the label width is 4”, adjust both print head pressure adjustment knobs to the same level. If the label is less than 2” wide, increase the left side print head pressure by rotating the adjustment knob clockwise and decrease the right side pressure by rotating the adjustment knob counter-clockwise to level 1.
2.7.2 Print Head Burn Line Adjustment Knob
Print head burn line adjustment knobs
ALTEC industrial identification
32 altec.nl | altec.be
The print head burn line adjustment knobs are used to fine tune the print quality for different thickness of media. Turning the knobs adjusts the print head’s burn line forward or backward as it relates to the platen roller.
Caution: Incorrectly adjusting these knobs can lead to poor print quality and
may cause damage to the printer. Proceed with caution.
The print head burn line default is set for general purpose printing media (plain paper and paper thickness less than 0.20mm).
Poor print quality when using paper thicker than 0.20mm may be due to the print head burn line not being at the optimized position. To improve the print quality, increase the head pressure or adjust the knobs counter-clockwise to move print head burn line toward the paper out direction then print again. Continue to adjust the burn line position and test print as necessary until the printout image is clear.
ALTEC industrial identification
33 altec.nl | altec.be
2.8 Using the Keyboard with PS/2 Interface
1. Turn off the power of printer.
2. Plug the keyboard with PS/2 interface cable into PS/2 connector on the rear of the printer.
3. Turn on the printer.
4. After pressing the F1 key of the keyboard, the LCD of printer will display as following.
File List 2/4
DRAM
> FLASH
CARD
5. Use up
↑ or down
↓ key of the keyboard to move “>” cursor and to select either
DRAM, FLASH or CARD that you previously saved file in and press Enter key of the keyboard to list files.
6. Select the file and press Enter key to execute the .BAS file.
FLASH File List
TEST1.BAS
> TEST2.BAS
TEST3.BAS
7. Then, you can type the words or the number of the copy from keyboard by your .BAS file program.
Press F1 key of the keyboard to start this function.
Press up ↑ or down ↓ key of the keyboard to move cursor of printer LCD display to select the option.
Press Esc key of the keyboard to return the previous menu.
Press Enter key of the keyboard to enter/execute cursor located option.
Press Ctrl + C keys of the keyboard to restart the printer and back to “Ready” state.
ALTEC industrial identification
34 altec.nl | altec.be
3. Menu Function
Main Menu Overview
Main Menu
Setup
↓
Printer Setup
↓
Sensor
↓
Serial Comm.
↓
*Ethernet
↓
Exit
File Manager
↓
File List
↓
Avail. Memory
↓
Del. All Files
↓
Exit
Diagnostics
↓
Print Config.
↓
Dump Mode
↓
Rotate Cutter
↓
Exit
Language
↓
English
↓
Chinese(TC)
↓
Chinese(SC)
↓
Japanese
↓
German
↓
Italian
↓
French
↓
Russian
↓
Polish
↓
Spanish
↓
Exit
Service
↓
Initialization
↓
Mileage Info.
↓
Exit
Exit
ALTEC industrial identification
35 altec.nl | altec.be
3.1 Setup Menu Overview
Printer Setup
↓
TSPL2
↓
ZPL2
↓
Exit
Sensor
↓
Status
↓
Calibration
↓
Exit
Setup
Serial Comm.
↓
Baud Rate
↓
Parity
↓
Data Bits
↓
Stop Bit(s)
↓
Exit ı
Ethernet
↓
Status
↓
Configure
↓
Exit
Exit
ALTEC industrial identification
36 altec.nl | altec.be
3.1.1-1 Printer Setup (TSPL2)
Printer Setup
TSPL2
Speed Density Direction Print Mode
↓
8
9
10
11
12
6
7
4
5
↓
12
13
14
15
10
11
8
9
6
7
4
5
2
3
0
1
↓
0
1
↓
None
Batch Mode
Peeler Mode
Cutter Mode
Cutter
Exit
Offset
↓
+000~-
Shift X Shift Y Reference X
+000~-000
↓
+000~-000
↓
000~999
Reference Y Code Page Country
↓
000~999
048
049
055
061
351
358
Exit
036
038
039
041
042
044
045
046
047
↓
001
002
003
031
032
033
034
1258
8859-1
8859-2
8859-3
8859-4
8859-5
8859-6
8859-7
857
1252
1250
1253
1254
1251
1255
1256
1257
8859-8
8859-9
8859-10
8859-15
950
936
932
949
SWE
SWI
437
850
852
860
863
865
↓
USA
BRI
GER
FRE
DAN
ITA
SPA
Exit
ALTEC industrial identification
37 altec.nl | altec.be
3.1.1-1.1 Speed:
Print Setup
> Speed
Density
Direction
1/12
Speed
6
Use this option to setup print speed. The each increament/decreament is 1 ips.
Press key to raise the print speed, and press key to decrease print speed. Press key to set it into printer. Press cancel the setting and return to the previous menu.
key to
Note: If printing from enclosed software/driver, the software/driver will send out the SPEED command, which will overwrite the setting set from the
front panel.
3.1.1-1.2 Density:
Print Setup
Speed
> Density
Direction
2/12
Density
8
Use this option to setup printing darkness. The available setting is from 0 to 15, and the step is 1. Printer default density is 8.You may need to adjust your density based on selected media.
Press and to increase/decrease the printing darkness. Press
key to enable the setting. Press key to cancel the setting and return to the previous menu.
Note: If printing from enclosed software/driver, the software/driver will send out the DENSITY command, which will overwrite the setting set from the front panel.
3.1.1-1.3 Direction:
Print Setup
Speed
Density
> Direction
3/12
Direction
0
The direction setting value is either 1 or 0. Use this option to setup the printout direction. Printer default printout direction is DIRECTION 0.
Press key to set the direction as 1, and key to enable the setting. Press to set it as 0, and key to cancel the setting and
ALTEC industrial identification
38 altec.nl | altec.be
return to the previous menu.
The following 2 figures are the printouts of DIRECTION 0 and 1 for your reference.
DIRECTION 0 DIRECTION 1
Note: If printing from enclosed software/driver, the software/driver will send out the command, which will overwrite the setting set from the front panel.
3.1.1-1.4 Print Mode: (None/Batch Mode/Peeler Mode/Cutter Mode/Cutter Batch)
Print Setup 4/12
Print Mode 2/6
Density
> Batch Mode
Direction
Peeler Mode
> Print Mode
Cutter Mode
This option is used to set the print mode.
Printer default setting is Batch Mode.
When enter this list, the print mode in the right side of “ >” icon is the printer current setting. Press and to select the different print mode and press
button to enable the setting. Press and return to the previous menu.
key to cancel the setting
Printer Mode
None
Batch Mode
Description
Next label top of form is aligned to the print head burn line location. (Tear Off Mode)
Once image is printed completely, label gap/black mark will be fed to the tear plate location for tear away.
Peeler Mode Enable the label peel off mode.
Cutter Mode Enable the label cutter mode.
ALTEC industrial identification
39 altec.nl | altec.be
Cutter Batch Cut the label once at the end of the printing job.
Note: If printing from enclosed software/driver, the software/driver will send out the command, which will overwrite the setting set from the front panel.
3.1.1-1.5 Offset:
Print Setup
Direction
Print Mode
> Offset
5/12
Offset
+000
This option is used to fine tune media stop location. Press the move the cursor from left digit to right digit, and press the value from “+” to “-” or “0” to “9”. Press the printer. Press button to set the value into key to cancel the setting and return to the previous menu.
The default value is +000. button to button to set the
Note: If printing from enclosed software/driver, the software/driver will send out the OFFSET command, which will overwrite the setting set from the front panel.
3.1.1-1.6 Shift X & Shift Y:
Print Setup 7/12
Offset
Shift X
> Shift Y
Shift Y
+000
This option is used to fine tune print position. Press the the cursor from left digit to right digit, and press the from “+” to “-” or “0” to “9”. Press the
Press button to set the value into printer. key to cancel the setting and return to the previous menu. The default value is +000. button to move button to set the value
Note: If printing from enclosed software/driver, the software/driver will send out the SHIFT command, which will overwrite the setting set from the front panel.
ALTEC industrial identification
40 altec.nl | altec.be
3.1.1-1.7 Reference X & Reference Y:
Print Setup 9/12
Shift Y
Reference X
> Reference Y
Reference Y
000
This option is used to set the origin of printer coordinate system horizontally and vertically. Press the button to move the cursor from left digit to right digit, and press the button to set the value from “0” to “9”. Press the button to set the value into printer. Press key to cancel the setting and return to the previous menu. The default value is 000.
Note: If printing from enclosed software/driver, the software/driver will send out the REFERENCE command, which will overwrite the setting set from the front panel.
3.1.1-1.8 Code Page:
Print Setup 10/12
Reference X
Reference Y
> Code Page
Code Page
> 850
852
860
11/41
Use this option to set the code page of international character set. For more information about code page, please to refer the programming manual.
When enter the code page list, the code page in the right side of “ >” icon is the printer current setting.
Press the and to select the code page, and press the button to enable the setting. Press key to cancel the setting and return to the previous menu.
Note: If printing from enclosed software/driver, the software/driver will send out the command, which will overwrite the setting set from the front panel.
USA
7-bit code page name
International
Character Set
USA
BRI
GER
FRE
DAN
British
German
French
Danish
code page number
437
850
852
860
863
8-bit
International
Character Set
United States
Multilingual
Slavic
Portuguese
Canadian/French
ALTEC industrial identification
41 altec.nl | altec.be
ITA
SPA
SWE
SWI
Italian
Spanish
Swedish
Swiss
865 Nordic
Windows Code Page (SBCS) code page number
International
Character Set
1252
1250
Latin 1
Central Europe
1253
1254
1251
1255
Greek
Turkish
Cyrillic
Hebrew
1256
1257
Arabic
Baltic
1258 Vietnam
Windows Code Page (DBCS) code page number
International
Character Set
950
936
932
949
Traditional Chinese Big5
Simplified Chinese GBK
Japanese Shift-JIS
Korean
ISO Code Page code page name
International
Character Set
8859-1
8859-2
Latin 1
Latin 2
8859-3
8859-4
8859-5
Latin 3
Baltic
Cyrillic
ISO Code Page code page number
International
Character Set
8859-7
8859-9
8859-10
8859-15
Greek
Turkish
Latin 6
Latin 9
3.1.1-1.9 Country:
Print Setup 11/12
Reference Y
Code Page
> Country
Country
> 001
002
003
1/23
Use this option to set the country code for the LCD display. Press the to select the country code, and press the
ALTEC industrial identification
42 and button to set the altec.nl | altec.be
value into printer. When enter this list, the country code in the right side of “ >” icon is the printer current setting. Press key to cancel the setting and return to the previous menu.
Code
001
Country
USA
Code Country Code Country Code Country
034
Spanish
(Spain)
044
United
Kingdom
055
002 Canadian-French 036 Hungarian 045 Danish 061
Brazil
English
(International)
003
Spanish
(Latin America) 038 Yugoslavian 046
Swedish 351 Portuguese
031 Dutch 039 Italian 047 Norwegian 358 Finnish
032 Belgian 041 Switzerland 048
033 French (France) 042 Slovak 049
Polish
German
ALTEC industrial identification
43 altec.nl | altec.be
3.1.1-2 Printer Setup (ZPL2)
Printer Setup
ZPL2
1
8
9
6
7
4
5
2
3
13
14
15
10
11
12
Darkness
↓
0
5
10
11
12
8
9
6
7
Speed
↓
4
Tear
Off
↓
+000
~-000
Mode
↓
Tear
Off
Peel
Off
Cutter
Exit
Width
↓ xxx
List
Fonts
List
Images
List
Formats
List
Setup
Control
Prefix
↓
Format
Prefix
↓
<x> xxx<x> xxx
Delimite r
Char
Media
Power Up
↓
Feed
Calibratio n
Length
No
Motion
Exit
Head
Close
↓
Feed
Calibratio n
Length
No
Motion
Exit
Label
Top
↓
+000
~-000
Left
Position
↓
+0000
~-0000
Exit
ALTEC industrial identification
44 altec.nl | altec.be
3.1.1-2.1 Darkness:
Print Setup
> Darkness
Print Speed
Tear off
1/17
Dankness
16
Use this option to setup printing darkness. The available setting is from 0 to 30, and the step is 1. Printer default density is 16.You may need to adjust your density based on selected media.
Press and to increase/decrease the printing darkness. Press
key to enable the setting. Press key to cancel the setting and return to the previous menu.
Note: If printing from enclosed software/driver, the software/driver will send out the command, which will overwrite the setting set from the front
panel.
3.1.1-2.2 Print Speed:
Print Setup 2/17
Darkness
> Print Speed
Tear Off
Print Speed
6
Use this option to setup print speed. The each increament/decreament is 1 ips.
Press key to raise the print speed, and press key to decrease print speed. Press key to set it into printer. Press cancel the setting and return to the previous menu.
key to
Note: If printing from enclosed software/driver, the software/driver will send out the command, which will overwrite the setting set from the front
panel.
3.1.1-2.3 Tear Off:
Print Setup
Darkness
Print Speed
> Tear Off
3/17
Tear Off
+000
This option is used to fine tune media stop location. Press the
ALTEC industrial identification
45 button to altec.nl | altec.be
move the cursor from left digit to right digit, and press the value from “+” to “-” or “0” to “9”. Press the button to set the button to set the value into printer. Press
The default value is +000. key to cancel the setting and return to the previous menu.
Note: If printing from enclosed software/driver, the software/driver will send out the command, which will overwrite the setting set from the front panel.
3.1.1-2.4 Print Mode: (Tear Off / Peel Off / Cutter)
Print Setup 4/17
Print Mode 1/4
Print Speed
> Tear Off
Tear Off
Peel Off
> Print Mode
Cutter
This option is used to set the print mode.
Printer default setting is Tear Off. When enter this list, the print mode in the right side of “ >” icon is the printer current setting. Press and to select the different print mode and press
button to enable the setting. Press and return to the previous menu.
key to cancel the setting
Printer Mode
Tear Off
Peel Off
Description
Next label top of form is aligned to the print head burn line location.
Enable the label peel off mode.
Cutter Enable the label cutter mode.
Note: If printing from enclosed software/driver, the software/driver will send out the command, which will overwrite the setting set from the front panel.
3.1.1-2.5 Print Width:
Print Setup 5/17
Tear Off
Print Mode
> Print Width
Print Width
812 dot
This option is used to set print width. Press the from left digit to right digit, and press the
button to move the cursor button to set the value from “0” to
ALTEC industrial identification
46 altec.nl | altec.be
“9” or “dot” to “mm”. Press the button to set the value into printer. Press key to cancel the setting and return to the previous menu.
Note: If printing from enclosed software/driver, the software/driver will send out the command, which will overwrite the setting set from the front panel.
3.1.1-2.6 List Fonts:
Print Setup
> List Fonts
List Images
List Formats
6/17 Self Test … Printing …
1/1
This feature is used to print current printer available fonts list to the label. The fonts stored in the printer’s DRAM, Flash or optional memory card. Press button to print the list.
3.1.1-2.7 List Images:
Print Setup 7/17 Self Test …
> List Images
List Formats
List Setup
Printing …
1/1
This feature is used to print current printer available images list to the label. The images stored in the printer’s DRAM, Flash or optional memory card. Press button to print the list.
3.1.1-2.8 List Formats:
Print Setup 8/17 Self Test …
> List Formats
List Setup
Control Prefix
Printing …
1/1
This feature is used to print current printer available formats list to the label. The formats stored in the printer’s DRAM, Flash or optional memory card. Press button to print the list.
ALTEC industrial identification
47 altec.nl | altec.be
3.1.1-2.9 List Setup:
Print Setup 9/17 Self Test …
> List Setup
Control Prefix
Format Prefix
Printing …
1/1
This feature is used to print current printer configuration to the label. Press button to print the list.
3.1.1-2.10 Control Prefix:
Print Setup 10/17
List Formats
List Setup
> Control Prefix
Control Prefix
< ~ > 7EH
This option is used to set control prefix character. Press the move the cursor from left digit to right digit, and press the value from “0” to “9” or “A” to “F”. Press the printer. Press button to set the value into key to cancel the setting and return to the previous menu. button to button to set the
3.1.1-2.11 Format Prefix:
Print Setup 11/17
List Setup
Control Prefix
> Format Prefix
Format Prefix
< ⋏ > 5EH
This option is used to set format prefix character. Press the move the cursor from left digit to right digit, and press the value from “0” to “9” or “A” to “F”. Press the printer. Press button to set the value into key to cancel the setting and return to the previous menu. button to button to set the
ALTEC industrial identification
48 altec.nl | altec.be
3.1.1-2.12 Delimiter Char:
Print Setup 12/17
Control Prefix
Format Prefix
> Delimiter Char
Delimiter Char
< , > 2CH
This option is used to set delimiter character. Press the the cursor from left digit to right digit, and press the button to move button to set the value from “0” to “9” or “A” to “F”. Press the
Press button to set the value into printer. key to cancel the setting and return to the previous menu.
3.1.1-2.13 Media Power Up:
Print Setup 13/17
Format Prefix
Delimiter Char
> Media Power Up
Media Power U 4/5
Length
> No Motion
Exit
This option is used to set the action of the media when you turn on the printer.
Printer default setting is No Motion. When enter this list, the print mode in the right side of “ >” icon is the printer current setting. Press the different print mode and press
and to select
button to enable the setting. Press key to cancel the setting and return to the previous menu.
Selections
Feed
Calibration
Length
Description
Printer will advance one label
Printer will calibration the sensor levels, determine length and feed label
Printer determine length and feed label
No Motion Printer will not move media
3.1.1-2.14 Head Close:
Print Setup 14/17
Delimiter Char
Media Power Up
> Head Close
Head Close
Length
> No Motion
Exit
4/5
ALTEC industrial identification
49 altec.nl | altec.be
This option is used to set the action of the media when you close the printhead.
Printer default setting is No Motion. When enter this list, the print mode in the right side of “ >” icon is the printer current setting. Press the different print mode and press
and to select
button to enable the setting. Press key to cancel the setting and return to the previous menu.
Selections
Feed
Calibration
Length
Description
Printer will advance one label
Printer will calibration the sensor levels, determine length and feed label
Printer determine length and feed label
No Motion Printer will not move media
3.1.1-2.15 Label Top:
Print Setup 15/17
Media Power Up
Head Close
> Label Top
Label Top
+000
This option is used to adjust print position vertically on the label. Press the button to move the cursor from left digit to right digit, and press the button to set the value from “+” to “-” or “0” to “1/2”. Press the set the value into printer. Press button to key to cancel the setting and return to the previous menu. The default value is +000 and range is -120 to +120 dots.
3.1.1-2.16 Left Position:
Print Setup 16/17
Head Close
Label Top
> Left Position
Left Position
+0000
This option is used to adjust print position horizontally on the label. Press the button to move the cursor from left digit to right digit, and press the button to set the value from “+” to “-” or “0” to “9”. Press the the value into printer. Press button to set key to cancel the setting and return to the previous menu. The default value is +0000 and range is -9999 to +9999 dots.
ALTEC industrial identification
50 altec.nl | altec.be
3.1.2 Sensor
Sensor
Status Calibration Exit ı
3.1.2.1 Status
This function is available to check the printer’s sensor status. When enter the [Status] option, you will see following message.
Paper Len.
Gap Size
Intensity
Ref. Level
812
24
3
512
3.1.2.2 Calibration
This option is used to set the media sensor type and calibrate the selected sensor. We recommend to calibrate the sensor before printing when changing the media.
ı
Calibration
Gap Mode
↓
Automatic
↓
Manual
↓
Pre-Printed
↓
Exit
Bline Mode
↓
Automatic
↓
Manual
↓
Pre-Printed
↓
Exit
Cont. Mode
↓
Automatic
↓
Manual
↓
Exit
Exit
ALTEC industrial identification
51 altec.nl | altec.be
A. Gap Mode
Calibration
> Gap Mode
Bline Mode
Cont. Mode
Press the the
1/4
Gap Mode
> Automatic
Manual
Pre-Printed
1/4
and buttons to scroll the cursor to the media type and press button to enter the sensor calibration mode.
Note: If printing from enclosed software/driver, the software/driver will send out the GAP or BLINE command, which will overwrite the sensor type setting set from the front panel.
A-1 Automatic
When enter the [Automatic] option, you will see following message, and printer will feed 2 to 3 gap labels to calibrate the sensor sensitivity automatically. When calibration is completed, the LCD screen will return to the previous menu.
Gap Mode
Automatic
A-2 Manual
In case “Automatic” sensor calibration cannot apply to the media, please use “Manual” function to calibrate the gap sensor manually.
Gap Mode
Automatic
> Manual
Pre-Printed
2/4
When enter [Manual] option, you will see following message. Please complete there steps:
Paper Len.
00812 dot
1. Press the button to move the cursor from left digit to right digit, and press the button to set the value from “0” to “9” and the “dot/ mm/ inch”. Press the button to set the paper length into the printer.
ALTEC industrial identification
52 altec.nl | altec.be
Gap Size
0024 dot
Gap Mode
Scan Backing
Intensity
Ref. Level
x
xxx
2. Press the button to move the cursor from left digit to right digit, and press the button to set the value from “0” to “9” and the “dot/ mm/ inch”. Press the button to set the gap size into the printer.
3. Open the print head mechanism, put the label backing (liner) under the media sensor. Press the button to set the value into the printer.
Media sensor
Label backing
(liner)
Gap Mode
Scan Paper
Intensity
Ref. Level
x
xxx
4. Then, Put the label with liner under the media sensor. Press the button to set the value into the printer.
Media sensor
Label with liner
Gap Mode
Complete
Intensity
Ref. Level
x
xxx
5. The gap sensor calibration is complete. Press the button the LCD screen will return to the previous menu.
A-3 Pre-Printed
This function can set the paper length and gap size before auto-calibrate the sensor sensitivity. It can to get the sensor sensitivity accurately.
3/4 Gap Mode
Manual
> Pre-Printed
Exit
ALTEC industrial identification
53 altec.nl | altec.be
When enter [Pre-Printed] option, you will see following message. Please complete there steps:
Paper Len.
00812 dot
Gap Size
0024 dot
Gap Mode
Pre-Printed
1. Press the button to move the cursor from left digit to right digit, and press the button to set the value from “0” to “9” and the “dot/ mm/ inch”. Press the button to set the paper length into the printer.
2. Press the button to move the cursor from left digit to right digit, and press the button to set the value from “0” to “9” and the “dot/ mm/ inch”. Press the button to set the gap size into the printer.
3. Then, printer will feed labels to calibrate the sensor sensitivity automatically. When calibration is completed, the LCD screen will return to the previous menu.
ALTEC industrial identification
54 altec.nl | altec.be
B. Bline Mode
Calibration
Gap Mode
> Bline Mode
Cont. Mode
2/4
Press the the
Bline Mode 1/4
> Automatic
Manual
Pre-Printed
and buttons to scroll the cursor to the sensor type. Press button to enter the black-mark sensor calibration mode.
B-1 Automatic
When enter the [Automatic] option, you will see following message and printer will feed the black mark label to calibrate the sensor sensitivity automatically. When calibration process is completed, the LCD screen will return to the previous menu.
Bline Mode
Automatic
B-2 Manual
In case “Automatic” sensor calibration cannot apply to the media, please use “Manual” function to calibrate the bline sensor manually.
2/4 Bline Mode
Automatic
> Manual
Pre-Printed
When enter [Manual] option, you will see following message. Please complete there steps:
Paper Len.
00151 dot
Bline Size
0024 dot
1. Press the button to move the cursor from left digit to right digit, and press the button to set the value from “0” to “9” and the “dot/ mm/ inch”. Press the button to set the paper length into the printer.
2. Press the button to move the cursor from left digit to right digit, and press the button to set the value from “0” to “9” and the “dot/ mm/ inch”. Press the button to set the bline size into the printer.
ALTEC industrial identification
55 altec.nl | altec.be
Bline Mode
Scan Mark
Intensity
Ref. Level
x
xxx
3. Open the print head mechanism, put the black mark under the media sensor. Press the button to set the value into the printer.
Media sensor
Black mark
Bline Mode
Scan Paper
Intensity
Ref. Level
x
xxx
4. Then, put the label without black mark under the media sensor. Press the button to set the value into the printer.
Media sensor
Label without black mark
Note:
Normally, the value of “Ref. Level” for mark should be larger than paper for over 128. If the media sensor fails to do so, you have to manually change the Intensity by pressing and to reach the above value.
Bline Mode
Complete
5. The bline sensor calibration is complete. Press the button the LCD screen will return to the previous menu.
Intensity x
Ref. Level xxx
B-3 Pre-Printed
This function can set the paper length and gap size before auto-calibrate the sensor sensitivity. It can to get the sensor sensitivity accurately.
3/4 Bline Mode
Manual
> Pre-Printed
Exit
When enter [Pre-Printed] option, you will see following message. Please
ALTEC industrial identification
56 altec.nl | altec.be
complete there steps:
Paper Len.
00812 dot
Bline Size
0024 dot
Bline Mode
Pre-Printed
1. Press the button to move the cursor from left digit to right digit, and press the button to set the value from “0” to “9” and the “dot/ mm/ inch”. Press the button to set the paper length into the printer.
2. Press the button to move the cursor from left digit to right digit, and press the button to set the value from “0” to “9” and the “dot/ mm/ inch”. Press the button to set the bline size into the printer.
3. Then, printer will feed labels to calibrate the sensor sensitivity automatically. When calibration is completed, the LCD screen will return to the previous menu.
ALTEC industrial identification
57 altec.nl | altec.be
C. Cont. Mode
Calibration
Bline Mode
> Cont. Mode
Exit
3/4
Cont. Mode
> Automatic
Manual
Exit
1/3
Press the the and buttons to scroll the cursor to the sensor type. Press button to enter the black-mark sensor calibration mode.
C-1 Automatic
When enter the [Automatic] option, you will see following message and printer will calibrate the sensor sensitivity automatically. When calibration process is completed, the LCD screen will return to the previous menu.
Cont. Mode
Automatic
C-2 Manual
In case “Automatic” sensor calibration cannot apply to the media, please use “Manual” function to calibrate the sensor manually.
2/3 Cont. Mode
Automatic
> Manual
Exit
When enter [Manual] option, you will see following message. Please complete there steps:
Cont. Mode
Remove Label
2. Remove the continuous label. Press the button to set the value into the printer.
Intensity
Ref. Level
x
xxx
Cont. Mode
Scan Paper
Intensity
Ref. Level
x
xxx
2. Then, put the continuous label under the media sensor. Press the button to set the value into the printer.
ALTEC industrial identification
58 altec.nl | altec.be
Cont. Mode
Complete
Intensity
Ref. Level
x
xxx
3. The sensor calibration is complete.
Press the menu. button the LCD screen will return to the previous
3.1.3 Serial Comm.
Baud Rate
↓
1200 bps
↓
2400 bps
↓
4800 bps
↓
9600 bps
↓
19200 bps
↓
38400 bps
↓
57600 bps
↓
115200 bps
↓
Exit
Parity
↓
None
↓
Odd
↓
Even
↓
Exit
Serial Comm.
Data Bits
↓
7
↓
8
↓
Exit
Stop Bit(s)
↓
1
↓
2
↓
Exit
Exit
ALTEC industrial identification
59 altec.nl | altec.be
3.1.3.1 Baud Rate
Serial Comm. 1/5
> Baud Rate
Parity
Data Bits
Baud Rate
> 9600 bps
19200 bps
38400 bps
4/9
This option is used to set the RS-232 baud rate. The default setting is 9600 bps.
Press and buttons to select the different baud rate and press
button to set the value into printer. When you enter this list, the baud rate value in the right side of “ >” icon is the current setting in the printer. Press key to cancel the setting and return to the previous menu.
3.1.3.2 Parity
Serial Comm. 2/5
Baud Rate
> Parity
Data Bits
Parity
> None
Odd
Even
1/4
This option is used to set the RS-232 parity. The default setting is “None”. Press
and buttons to select the different parity and press button to set the value into printer. When you enter this list, the parity in the right side of “ >” is the printer current setting. Press and return to the previous menu.
key to cancel the setting
3.1.3.3 Data Bits:
Serial Comm. 3/5
Baud Rate
Parity
> Data Bits
Data Bits
7
> 8
Exit
2/3
This option is used to set the RS-232 Data Bits. The default setting is “8” data bits.
Press and buttons to select the different Data Bits and press
button to set the value into printer. When you enter this list, the Data Bits in the right side of “
>” icon is the printer current setting. Press cancel the setting and return to the previous menu.
key to
ALTEC industrial identification
60 altec.nl | altec.be
3.1.3.4 Stop Bit
(s)
:
Serial Comm. 4/5
Parity
Data Bits
> Stop Bit(s)
Stop Bit(s)
> 1
2
Exit
1/3
This option is used to set the RS-232 Stop Bits. The default setting is “1” stop bit.
Press and buttons to select the different Stop Bits and press
button to set the value into printer. When you enter this list, the option in the right side of “ >” icon is the printer current setting. Press cancel the setting and return to the previous menu.
key to
ALTEC industrial identification
61 altec.nl | altec.be
3.1.4 Ethernet
Use this menu to configure internal Ethernet configuration check the printer’s Ethernet module status, and reset the Ethernet module. This function is available on the LCD display when Ethernet card is installed.
Press and buttons to select the different options and press button to enter the option. Press key to cancel the setting and return to the previous menu.
Ethernet
Status
↓
IP Address
↓
MAC
↓
Exit
Configure
↓
DHCP
↓
Static IP
↓
Exit
Exit
3.1.4.1 Status: (IP Address / MAC)
Use this menu to check the Ethernet setting status.
3.1.4.1.1 IP Address
Ethernet
> Status
Configure
Exit
1/3
Status
> IP Address
MAC
Exit
1/3
IP Address
0.0.0.0
Subnet Mask
0.0.0.0
Gateway
0.0.0.0
The IP address information will be shown on the LCD display. Please press or button to return to the previous menu.
ALTEC industrial identification
62 altec.nl | altec.be
3.1.4.1.2 MAC
Ethernet
> Status
Configure
Exit
1/3
Status
IP Address
> MAC
Exit
2/3 MAC Address
001B82-FF0918
The MAC address information will be shown on the LCD display. Please press or button to return to the previous menu.
3.1.4.2 Configure: (DHCP / Static IP)
Use this menu to set the printer’s DHCP and Static IP.
3.1.4.2.1 DHCP
Ethernet
Status
> Configure
Reset
2/4
Configure
> DHCP
Static IP
Exit
1/3
Press and
to enter. Press previous menu. buttons to select the DHCP function and press key to cancel the setting and return to the
DHCP
SELECT:
MENU:
Press
Press
YES
NO
button the printer will set DHCP and restart to reset the setting. button to return to the previous menu.
ALTEC industrial identification
63 altec.nl | altec.be
3.1.4.2.2 Static IP
Use this menu to set the printer’s IP address, subnet mask and gateway.
Ethernet
Status
> Configure
Exit
2/3
Configure
DHCP
> Static IP
Exit
2/3
Press and buttons to select the different options and press button to enter the option. Press key to cancel the setting and return to the previous menu.
IP Address
000.000.000.000
Subnet Mask
000.000.000.000
Gateway
000.000.000.000
Press button to move the cursor from left to right digits and press the
button to scroll the value from “0” to “9”. Press button to next setting.
Static IP
SELECT:
MENU:
YES
NO
Press the
Press
button printer will restart to reset the Ethernet module setting.
key to cancel the setting.
ALTEC industrial identification
64 altec.nl | altec.be
3.2 File Manager
This feature is used to check the printer available memory and file list.
File Manager
File List
↓
DRAM
↓
FLASH
↓
CARD
↓
Exit
Avail. Memory Del. All Files
↓
DRAM
↓
FLASH
↓
CARD
↓
Exit
Exit ı
3.2.1 File List
Use this menu to show, delete and run (.BAS) the files saved in the printer
DRAM/Flash/Card memory.
To show the files:
File Manager 1/4 File List
> File List
Avail. Memory
Del. All Files
> FLASH
CARD
Exit
2/4 FLASH File List
> DEMO.TTF
DEMO.BAS
button.
To delete the file:Please follow the order to press the
FLASH File List DEMO.TTF
> DEMO.TTF
DEMO.BAS
1.75 MB
DOWN: Delete
To run the file (.BAS):Please follow the order to press the
FLASH File List DEMO.BAS
DEMO.TTF
> DEMO.BAS DOWN:
SELECT:
406 Byte(S)
Delete
Run
button.
3.2.2 Avail. Memory
Use this menu to show available memory space.
ALTEC industrial identification
65 altec.nl | altec.be
File Manager
File List
> Avail. Memory
Del. All Files
2/4 Avail. Memory
DRAM: 256 KB
FALSH:
CARD:
6656 KB
0 KB
3.2.3 Del. All Files
Use this menu to delete all files.
Press
Press button to delete all files in the device. to cancel deleting files and go back to previous menu.
File Manager 3/4 File List 1/4 Del. All Files
File List
Avail. Memory
> Del. All File
> DRAM
FALSH
CARD
SELECT:
MENU:
YES
NO
ALTEC industrial identification
66 altec.nl | altec.be
3.3 Diagnostics
Diagnostics
Print Config.
Dump Mode Rotate Cutter Exit ı
3.3.1 Print Config.
This feature is used to print current printer configuration to the label. On the sconfiguration printout, there is a print head test pattern, which is useful for checking if there is any dot damage on the print head heater element.
Diagnostics 1/4 Self Test … Printing …
1/1 > Print Config.
Dump Mode
Rotate Cutter
Self-test printout
Printer model name & Main board firmware version
Printer serial number
Printed mileage
Main board firmware checksum
Serial port setting
Code page
Country code
Print speed
Print darkness
Label size (width, height)
Black mark or gap size (vertical gap, offset)
Sensor sensitivity
Ethernet settings information (option)
File management information
Print head test pattern
ALTEC industrial identification
67 altec.nl | altec.be
Self-test printout (with printer firmware V7.0 and later version)
Model name
F/W version
Firmware checksum
Printer S/N
Configuration file
System date
System time
Printed mileage (meter)
Cutting counter
Print speed (inch/sec)
Print darkness
Label size (inch)
Gap distance (inch)
Gap/black mark sensor intension
Code page
Country code
ZPL setting information
Print darkness
Print speed (inch/sec)
Label size
Control prefix
Format prefix
Delimiter prefix
Printer power up motion
Printer head close motion
Note:
ZPL is emulating for Zebra language.
®
RS232 serial port configuration
ALTEC industrial identification
68 altec.nl | altec.be
Numbers of download files
Total & available memory space
Print head check pattern
ALTEC industrial identification
69 altec.nl | altec.be
3.3.2 Dump Mode
Captures the data from the communications port and prints out the data received by printer. In the dump mode, all characters will be printed in 2 columns as following. The left side characters are received from your system and right side data are the corresponding hexadecimal value of the characters. It allows users or engineers to verify and debug the program.
Dump Mode Diagnostics 2/4
Pritn Config.
> Dump Mode
Rotate cutter
Printing …
1/1
Note:
1. Dump mode requires 4” wide paper width.
2. Turn off / on the power to resume printer for normal printing.
3. Press FEED button to back to the previous menu.
DOWNLOA 0D 0A 44 4F 57 4E 4C 4F 4I
D „TEST2. 44 20 22 54 45 53 54 32 2E
DAT“,5,CL 44 41 54 22 2C 35 2C 43 4C
S DOWNLO 53 0D 0A 44 4F 57 4E 4C 4F
AD F,“TES 41 44 20 46 2C 22 54 45 53
T4.DAT“,5 54 34 2E 44 41 54 22 2C 35
,CLS DOW 2C 43 4C 53 0D 0A 44 4F 57
NLOAD „TE 4E 4C 4F 41 44 20 22 54 45
ST2.DAT”, 53 54 32 2E 44 41 54 22 2C
5,CLS DO 35 2C 43 4C 53 0D 0A 44 4F
WNLOAD F, 57 4E 4C 4F 41 44 20 46 2C
„TEST4.DA 22 54 45 53 54 34 2E 44 41
T”,5,CLS 54 22 2C 35 2C 43 4C 53 0D
DOWNLOAD 0A 44 4F 57 4E 4C 4F 41 44
“TEST2.D 20 22 54 45 53 54 32 2E 44
AT”,5,CLS 41 54 22 2C 35 2C 43 4C 53
DOWNLOA 0D 0A 44 4F 57 4E 4C 4F 4I
D F,“TEST 44 20 46 2C 22 54 45 53 54
4.DAT“,5, 34 2E 44 41 54 22 2C 35 2C
CLS 43 4C 53 0D 0A
ASCII Data
Hexdecimal data related to left column of ASCII data
ALTEC industrial identification
70 altec.nl | altec.be
3.3.3 Rotate Cutter
In case paper is jammed in the cutter, this feature can rotate the cutter blade forward or reverse direction, which is helpful to remove the jammed paper easily from the cutter.
Diagnostics 3/4
Print Config.
UP:
DOWN:
Rev.
Fwd.
Dump Mode
> Rotate Cutter MENU: Exit
3.4 Language
ı
Language
English Chinese (TC) Chinese (SC) Japanese German Italian French Russian Polish Spanish Exit
This option is used to setup the language on LCD display.
Press and buttons to scroll the curser to desire language and press button to select this option. Press key to cancel the setting and return to the previous menu. The default language setting is English.
ALTEC industrial identification
71 altec.nl | altec.be
3.5 Service
Service
Initialization Mileage Info.
Exit
This feature is used to restore printer settings to defaults and display printer mileage information.
3.5.1 Initialization
Service 1/3
> Initialization
Mileage Info.
Exit
Initialization
SELECT
MENU
YES
NO
Initializing …
The printer settings are restored to defaults as below once printer is initialized.
Note :
When printer initialization is done, please calibrate the gap or black mark sensor before printing.
Parameter
Speed
ATP-4200:
ATP-4300:
ATP-4600 :
Default setting
6 IPS (152 mm/sec)
4 IPS (101.6 mm/sec)
3 IPS (76.2 mm/sec)
Density
Label width
Label height
Sensor type
Gap setting
Print direction
Reference point
Offset
Print mode
8
4.00”(101.6mm)
4.00”(101.6mm)
Gap sensor
0.12”(3.0mm)
0
0,0(upper left corner)
0
Batch mode
Serial port settings 9600 bps, none parity, 8 data bits, 1 stop bit
Code page
850
Country code
001
Clear flash memory No
Shift X
Shift Y
0
0
ALTEC industrial identification
72 altec.nl | altec.be
Gap sensor sensitivity
Bline sensor sensitivity
Language
IP address
3 (Will be reset. Need to re-calibrate the gap)
2 (Will be reset. Need to re-calibrate the gap)
English
DHCP
3.5.2 Mileage Info.
Use this option to check the printed mileage (displayed in meter).
Service 1/3 Mileage: (m)
Initialization
4016
> Mileage Info.
Exit
Labels: (pcs.)
51698
ALTEC industrial identification
73 altec.nl | altec.be
4. Diagnostic Tool
The Diagnostic Utility is a toolbox that allows users to explore the printer’s settings and status; change printer settings; download graphics, fonts, and firmware; create printer bitmap fonts; and to send additional commands to the printer. Using this convenient tool, you can explore the printer status and settings and troubleshoot the printer.
Note: This utility works with printer firmware V6.00 and later versions.
4.1 Start the Diagnostic Tool
1. Double click on the Diagnostic tool icon to start the software.
2. There are four features (Printer Configuration, File Manager, Bitmap Font Manager,
Command Tool) included in the Diagnostic utility.
Features tab
Interface
Printer functions
Printer setup
Printer Status
ALTEC industrial identification
74 altec.nl | altec.be
4.2 Printer Function
(Calibrate sensor, Ethernet setup, RTC setup………)
1. Select the PC interface connected with bar code printer.
2. Click the “Function” button to setting.
3. The detail functions in the Printer Function Group are listed as below.
Function
Calibrate Sensor
Ethernet Setup
Description
Calibrate the sensor specified in the Printer Setup group media sensor field
Setup the IP address, subnet mask, gateway for the on board Ethernet (Please refer to next section)
Synchronize printer Real Time Clock with PC RTC Time
Print Test Page
Reset Printer
Factory Default
Print a test page
Reboot printer
Initialize the printer and restore the settings to factory default.
To activate the printer dump mode. Dump Text
Ignore AUTO.BAS Ignore the downloaded AUTO.BAS program
Configuration Page Print printer configuration
Note:
For more information about Diagnostic Tool, please refer to the diagnostic utility quick start guide in the CD disk \ Docs \ User Guides directory.
ALTEC industrial identification
75 altec.nl | altec.be
5 Setting Ethernet by Diagnostic Utility
The Diagnostic Utility is enclosed in the CD disk \Docs\User Guides directory. Users can use Diagnostic Tool to setup the Ethernet by RS-232, USB and Ethernet interfaces. The following contents will instruct users how to configure the Ethernet by these three interfaces.
5.1 Using USB interface to setup Ethernet interface
1. Connect the USB cable between the computer and the printer.
2. Turn on the printer power.
3. Start the Diagnostic Utility by double clicking on the icon.
Note: This utility works with printer firmware V6.00 and later versions.
4. The Diagnostic Utility default interface setting is USB interface. If USB interface is connected with printer, no other settings need to be changed in the interface field.
5. Click on the “Ethernet Setup” button from “Printer Function” group in Printer
Configuration tab to setup the IP address, subnet mask and gateway for the on board Ethernet.
ALTEC industrial identification
76 altec.nl | altec.be
5.2 Using RS-232 interface to setup Ethernet interface
1. Connect the computer and the printer with a RS-232 cable.
2. Turn on the printer power.
3. Start the Diagnostic Utility by double clicks on the icon.
Note: This utility works with printer firmware V6.00 and later versions.
4. Select “COM” as interface then click on the “Setup” button to setup the serial port baud rate, parity check, data bits, stop bit and flow control parameters.
5. Click on the “Ethernet Setup” button from printer function of Printer Configuration tab to setup the IP address, subnet mask and the gateway for the on board Ethernet.
ALTEC industrial identification
77 altec.nl | altec.be
5.3 Using Ethernet interface to setup Ethernet interface
1. Connect the computer and the printer to the LAN.
2. Turn on the printer power.
3. Start the Diagnostic Utility by double clicks on the icon.
Note: This utility works with printer firmware V6.00 and later versions.
4. Select “Ethernet” as the interface then click on the “Setup” button to setup the IP address, subnet mask and gateway for the on board Ethernet.
5. Click the “Discover Device” button to explore the printers that exist on the network.
6. Select the printer in the left side of listed printers, the correspondent IP address will be shown in the right side “IP address/Printer Name” field.
7. Click “Change IP Address” to configure the IP address obtained by DHCP or static.
The default IP address is obtained by DHCP. To change the setting to static IP address, click “Static IP” radio button then enter the IP address, subnet mask and
ALTEC industrial identification
78 altec.nl | altec.be
gateway. Click “Set IP” to take effect the settings.
Users can also change the “Printer Name” by another model name in this fields then click “Set Printer Name” to take effect this change.
Note: After clicking the
“Set Printer Name” or “Set IP” button, printer will reset to take effect the settings.
8. Click “Exit” button to exit the Ethernet interface setup and go back to Diagnostic Tool main screen.
Factory Default button
This function will reset the IP, subnet mask, gateway parameters obtained by DHCP and reset the printer name.
Web setup button
Except to use the Diagnostic Utility to setup the printer, you can also explore and configure the printer settings and status or update the firmware with the IE or Firefox web browser. This feature provides a user friendly setup interface and the capability to manage the printer remotely over a network.
ALTEC industrial identification
79 altec.nl | altec.be
6. Troubleshooting
6.1 Common Problems
The following guide lists the most common problems that may be encountered when operating this bar code printer. If the printer still does not function after all suggested solutions have been invoked, please contact the Customer Service Department of your purchased reseller or distributor for assistance.
Problem Possible Cause
Power indicator does not illuminate
* The power cord is not properly connected.
Carriage Open
* The printer carriage is open.
Recovery Procedure
* Plug the power cord in printer and outlet.
* Switch the printer on.
* Please close the print carriage.
No Ribbon
* Running out of ribbon.
* The ribbon is installed incorrectly.
* Supply a new ribbon roll.
* Please refer to the steps in user’s manual to reinstall the ribbon.
No Paper
* Running out of label.
* The label is installed incorrectly.
* Gap/black mark sensor is not calibrated.
* Supply a new label roll.
* Please refer to the steps in user’s manual to reinstall the label roll.
* Calibrate the gap/black mark sensor.
Paper Jam
Take Label
UP:
DOWN:
MENU:
Fwd.
Rev.
Exit
* Gap/black mark sensor is not set properly.
* Make sure label size is set properly.
* Labels may be stuck inside the printer mechanism.
* Calibrate the gap/black mark sensor.
* Set label size correctly.
* Peel function is enabled.
* Cutter jam.
* There is no cutter installed on the printer.
* Cutter PCB is damaged.
* If the peeler module is installed, please remove the label.
* If there is no peeler module in front of the printer, please switch off the printer and install it.
* Check if the connector is plugging correctly.
* If the cutter module is installed, please press UP or DOWN key to rotate the cutter up or down to make the knife back to the right position.
* Remove the label.
* Make sure the thickness of label is less than 200 g/m2 (for regular cutter) or 300 g/m2 (for heavy duty cutter).
* Replace a cutter PCB.
ALTEC industrial identification
80 altec.nl | altec.be
Not Printing
Memory full
( FLASH / DRAM )
* Cable is not well connected to serial or
USB interface or parallel port.
* The serial port cable pin configuration is not pin to pin connected.
* Re-connect cable to interface.
* If using serial cable,
- Please replace the cable with pin to pin connected.
- Check the baud rate setting. The default baud rate setting of printer is 9600,n,8,1.
* If using the Ethernet cable,
- Check if the Ethernet RJ-45 connector green
LED is lit on..
- Check if the Ethernet RJ-45 connector amber
LED is blinking.
- Check if the printer gets the IP address when using DHCP mode.
- Check if the IP address is correct when using the static IP address.
- Wait a few seconds let the printer get the communication with the server then check the
IP address setting again.
* Chang a new cable.
* Ribbon and media are not compatible.
* Verify the ribbon-inked side.
* Reload the ribbon again.
* Clean the printhead.
* The print density setting is incorrect.
* Printhead’s harness connector is not well connected with printheat. Turn off the printer and plug the connector again.
* Check if the stepping motor is plugging in the right connector.
* Check your program if there is a command
PRINT at the end of the file and there must have
CRLF at the end of each command line.
* Delete unused files in the FLASH/DRAM.
* The max. numbers of file of DRAM is 256 files.
* The max. user addressable memory space of
DRAM is 2048KB.
* The space of FLASH/DRAM is full.
* The max. numbers of file of FLASH is 256 files.
* The max. user addressable memory space of
FLASH is 6656 KB
SD card is unable to use
PS/2 port does not work
* SD card is damaged.
* SD card doesn’t insert correctly.
* Use the non-approved SD card manufacturer.
* Did not turn off power prior to plug in the PS/2 keyboard.
* PS/2 keyboard is damaged.
* PS/2 keyboard doesn’t plug-in correctly.
* There is no BAS file in the printer.
* Use the supported capacity SD card.
* Insert the SD card again.
* The supported SD card spec and the approved
SD card manufacturers, please refer to section
2.2.3.
* Turn off printer power prior to plug in the PS/2 keyboard.
* Plug the PS/2 keyboard again.
* Make sure the keyboard is fine.
* Make sure if there is any BAS file downloaded into printer.
ALTEC industrial identification
81 altec.nl | altec.be
Poor Print Quality
* Ribbon and media is loaded incorrectly
* Dust or adhesive accumulation on the print head.
* Print density is not set properly.
* Printhead element is damaged.
* Ribbon and media are incompatible.
* The printhead pressure is not set properly.
* Reload the supply.
* Clean the printhead.
* Clean the platen roller.
* Adjust the print density and print speed.
* Run printer self-test and check the print head test pattern if there is dot missing in the pattern.
* Change proper ribbon or proper label media.
* Adjust the printhead pressure adjustment knob.
- If the left side printout is too light, please adjust the left side pressure adjustment knob to the higher index (higher pressure). If the pressure adjustment knob has been adjust to index “5” and the poor print quality is still at the left side of the printout, please adjust the pressure adjustment knob to index “1” and use the
Z-axis adjustment knob to fine tune the pressure.
- If the right side printout is too light, please adjust the right side pressure adjustment knob to the higher index (higher pressure) to improve the print quality.
* If the label thickness is more than 0.22 mm, the print quality might be not good enough, please adjust the heater line adjustment screw counter clockwise to get the best print quality.
* The release lever does not latch the printhead properly.
LCD panel is dark but the LEDs are light
* The printer initialization is unsuccessful.
* Turn OFF and ON the printer again.
* Initialize the printer.
LCD panel is dark and
LEDs are lit on, but the label is feeding
* The LCD panel harness connector is loose.
forward
* The LCD panel harness connector is plugged upside down.
Ribbon end sensor doesn’t work
* The ribbon sensor hole is covered with dust.
Peel sensor is not working
* Peel sensor is not located on the correct position.
* The connector is loose.
Cutter is not working * The connector is loose.
* Clear the dust in the sensor hole by the blower.
* Make sure that the media goes through the Peel sensor.
* Plug the connect cable correctly.
* Plug in the connect cable correctly.
Label feeding is not stable (skew) when printing
Skip labels when printing
* The media guide does not touch the edge of the media.
* If the label is moving to the right side, please move the label guide to left.
* If the label is moving to the left side, please move the label guide to right.
* Label size is not specified properly.
* Sensor sensitivity is not set properly.
* The media sensor is covered with dust.
* Check if label size is setup correctly.
* Calibrate the sensor by Auto Gap or Manual
Gap options.
* Clear the GAP/Black mark sensor by blower.
ALTEC industrial identification
82 altec.nl | altec.be
The printing position of small label is incorrect
* Media sensor sensitivity is not set properly.
* Label size is incorrect.
* The parameter Shift Y in the LCD menu is incorrect.
* The vertical offset setting in the driver is incorrect.
* Calibrate the sensor sensitivity again.
* Set the correct label size and gap size.
* Press [MENU] [SELECT] x3[DOWN]x6
[SELECT] to fine tune the parameter of Shift Y.
* If using the software BarTender, please set the vertical offset in the driver.
The left side printout position is incorrect
* Wrong label size setup.
* The parameter Shift X in LCD menu is incorrect.
* Set the correct label size.
* Press [MENU] [SELECT] x 3 [DOWN] x 5
[SELECT] to fine tune the parameter of Shift
X.
Missing printing on the left or right side of
* Wrong label size setup.
* Set the correct label size.
label
RTC time is incorrect when reboot the printer
* The battery has run down.
* Check if there is a battery on the main board.
Multi interface board doesn’t work
* The installation is incorrect.
Power and Error LEDs
* Power switch OFF and ON too fast.
are blinking fast
Wrinkle Problem
* Printhead pressure is incorrect.
* Ribbon installation is incorrect.
* Media installation is incorrect.
* Print density is incorrect.
* Media feeding is incorrect.
Gray line on the blank label
* The printhaed is dirty.
* The platen roller is dirty.
* Check if the board is plugged in the right connector.
* Turn off the printer and wait all LEDs are dark, and turn on the printer again.
* Please refer to the next chapter.
* Please set the suitable density to have good print quality.
* Make sure the label guide touch the edge of the media guide.
* Clean the printhead.
* Clean the platen roller.
* Turn off and on the printer to skip the dump mode.
* Re-set the Rs-232 setting.
ALTEC industrial identification
83 altec.nl | altec.be
6.2 Mechanism Fine Adjustment to Avoid Ribbon Wrinkles
This printer has been fully tested before delivery. There should be no ribbon wrinkle presented on the media for general-purpose printing application. Ribbon wrinkle is related to the media thickness, print head pressure balance, ribbon film characteristics, print darkness setting…etc. In case the ribbon wrinkle happens, please follow the instructions below to adjust the printer parts.
Print head pressure adjustment knob
Adjustable
Printer
Parts
Z-axis mechanism adjustment knob
Ribbon guide plate
Symptom
1. Wrinkle happens from label lower left to 2. Wrinkle happens from label lower right
upper right direction (“ˊ”) to upper left direction (“ˋ”)
Wrinkle
Example
Feed direction
ALTEC industrial identification
84 altec.nl | altec.be
Adjust the print head pressure adjustment knob
Left knob
Right knob
Adjust the print head pressure adjustment knob
Left knob
Right knob
The print head pressure adjustment knob has 5 levels of settings. Clockwise direction adjustment is to increase the print head pressure. Counter
Clockwise adjustment can decrease the print head pressure.
If the wrinkle on the label starts from the lower left side to upper right side, please do following adjustment.
The print head pressure adjustment knob has 5 levels of settings. Clockwise direction adjustment is to increase the print head pressure. Counter
Clockwise adjustment can decrease the print head pressure.
If the wrinkle on the label starts from the lower right side to upper left side, please do following adjustment.
1. Decrease the right side print head pressure adjustment knob setting 1 level per each adjustment then print the label again to check if wrinkle is gone.
2. If the right side print head adjustment knob setting has been set to index 1 (the lowest pressure index), please increase the left side print head pressure.
3. If the left side print head adjustment knob setting has been set to 5 (the highest pressure index) the wrinkle can’t be avoid, please rotate the both knobs back to setting 1 then rotate the
Z-axis mechanism adjustment knob clockwise for a few degrees and print again for fine tune the print head pressure distribution.
1. Decrease the left side print head pressure adjustment knob setting 1 level per each adjustment then print the label again to check if wrinkle is gone.
2. If the left side print head adjustment knob level has been set to index 1 (the lowest index), please increase the right side print head pressure.
Z axis mechanism adjustment knob
Note for step 3:
*Factory default setting, the Z-axis knob is rotated counter clockwise to the end of thread.
*Turn the Z-axis mechanism adjustment knob clockwise until you feel the knob touch the mechanism for the first adjustment.
* If the wrinkle is still there, please turn the Z-axis mechanism adjustment knob clockwise about
1/4 circle each time for adjustment
* If the winkled direction is change from “ˊ” to
“ˋ” by adjusting the Z-axis mechanism adjustment knob, please turn the Z axis mechanism adjustment knob counter clockwise to avoid the wrinkle.
ALTEC industrial identification
85 altec.nl | altec.be
7. Maintenance
This session presents the clean tools and methods to maintain your printer.
2.
Please use one of following material to clean the printer.
Cotton swab ( Head cleaner pen )
Lint-free cloth
Vacuum / Blower brush
100% ethanol
2.
The cleaning process is described as following
Printer Part Method
1. Always turn off the printer before cleaning the print head.
2. Allow the print head to cool for a minimum of one minute.
3. Use a cotton swab (Head cleaner pen) and 100% ethanol to clean the print head surface.
Interval
Clean the print head when changing a new label roll
Print Head
Platen Roller
Tear Bar/Peel
Bar
Sensor
Exterior
Interior
1. Turn the power off.
2. Rotate the platen roller and wipe it thoroughly with 100% ethanol and a cotton swab, or lint-free cloth.
Use the lint-free cloth with 100% ethanol to wipe it.
Compressed air or vacuum
Wipe it with water-dampened cloth
Brush or vacuum
Clean the platen roller when changing a new label roll
As needed
Monthly
As needed
As needed
ALTEC industrial identification
86 altec.nl | altec.be
Note:
Do not touch printer head by hand. If you touch it careless, please use ethanol to clean it.
Please use 100% Ethenol. DO NOT use medical alcohol, which may damage the printer head.
Regularly clean the print head and supply sensors once change a new ribbon to keep printer performance and extend printer life.
ALTEC industrial identification
87 altec.nl | altec.be
Revise History
Date
2012/6/29
2012/9/24
2012/10/2
Content
* Revise pictures of label roll guard
* Revise section 1.6
* Revise chapter 2.2.2, 2.5.1, 2.6.1 and 2.6.2
* Revise chapter 2.6.3, 2.6.5 and 3.1.2
2013/4/1
2013/5/8
2014/11/5
* Modify chapter1.2.2 for cutter spec
* Modify chapter 3.3.1 for V7.0 F/W (Self-test)
* Modify chapter 1.3
* Add UL caution
ALTEC industrial identification
88 altec.nl | altec.be
ALTEC industrial identification
Nederland
Nieuwland Parc 159
3351 LJ Papendrecht
Tel: +31(0)78 615 20 33
E-mail: [email protected]
Website: www.altec.nl
België
Erasmuslaan 11
1804 Eppegem
Tel: +32(0)2 270 34 88
E-mail: [email protected]
Website: www.altec.be
89 altec.nl | altec.be

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Die-Casting Aluminum Chassis
- Metal Cover with Large Clear Media View Window
- Moveable Gap Sensor
- Internal Ethernet Print Server
- USB 2.0 Interface
- Serial RS-232C Interface
- Centronics Interface
- PS/2 Keyboard Interface
- SD FLASH Card Memory
- High-Performance 32-Bit RISC Processor