BlinkFX DMX 14 Channel Emitter Controls DMX QUICK START SET

BlinkFX DMX 14 Channel Emitter Controls DMX QUICK START SET
BlinkFX DMX 14 Channel Emitter Controls
Fixture Part Number: BlinkFX-­‐R1
CH 1 Dimmer
255 0
Dark Bright CH 2 Red
CH 4 Blue
209 -­‐ 224 = ID 14 CH 5 Color Wheel
0 = Honor RGB of CH 2, 3 & 4 CH 6 Color Wheel Speed
Change Speed When CH 5 = 147-­‐255 CH 7 Blink On Time
0 CH 8 Blink Off Time
0 1-­‐16 32-­‐47 17-­‐31 48-­‐63 64-­‐79 241 -­‐ 255 = ID 16 147-­‐255 96-­‐146 80-­‐95 Cycle All 255 1 Fast Slow 255 Fast Slow 255 Fast Slow 255 0 Fast CH 10 Pulse Off Time
0 CH 11 Buzz On Time*
0 CH 12 Buzz Off Time*
0 Slow 255 Fast Slow 255 2) Plug the BlinkFX control emider into a 110v AC power plug. Then connect the emider to an industry standard DMX512 lighXng control board with at least 14 Channels using 3-­‐pin XLR cable. Follow the instruccons included with your DMX512 control board to set up a fixture profile for the 14 Channel BlinkFX emider. 3) IMPORTANT! When connected to a DMX control board, set Channel 14 Emi[er Power to a value greater than "0" before seing other DMX channel values. When emider power is set to "0" no signal is sent. Emider power may be set in increments of 10%/20%. Experiment with emider power seings to maximize response rate for the area of use. Small areas require lower power se_ngs. Too much power in a small area creates signal cluder reducing the responsiveness of the LED light devices. Larger areas require higher power seings for greater range and responsiveness. Test your venue thoroughly before the event to dial in the ideal power seings. Range and coverage results will vary depending on the venue. 4) Ideal placement of emiders is mounted on a truss or tower at least 10 feet above the audience at a downward angle. Smaller venues may work with lower placement, above head high. When using mulcple fixtures to cover a large area or achieve zoned effects, experiment ahead of cme with placement and emider power seings (adjust Channel 14 Emider Power for test). Walk around the venue with BlinkFX receiver device to test for range and dead spots. Adjust emider placement and power accordingly. SPECIAL EFFECTS SETTINGS Strobe -­‐ White -­‐ 240 = ID 5 > 146; Channel 6 = 0 to 3 Channel 1 > 0; C225 hannel Fast Slow 255 Fast Slow 16 -­‐ 30 = ID 1 CH 13 Device ID
1) For DMX operacon of BlinkFX control emider(s), set dip switch pin 10 to "On" then set fixture address start channel using pins 1-­‐9 (see DMX dip switch addressing key at bodom of page). The following example is set for DMX control with a fixture address of "1". Mulcple emiders may be synchronized under one common address or zoned with different addresses. CH 3 Green
CH 9 Pulse On Time
DMX QUICK START SET-­‐UP AND OPERATION 0 -­‐ 15 = Global All IDs Respond 31 -­‐ 45 = ID 2 46 -­‐ 60 = ID 3 61 -­‐ 75 = ID 4 Off Strobe -­‐ Specific Color Channel 1 > 0; Channel 5 < 146; Channel 6 = 0 to 3 Twinkle -­‐ Asynchronous Blinking Channel 1 > 0; Choose Any Color; Channel 7 = 0; Channel 8 = 255 91 -­‐ 105 = ID 6 106 -­‐ 120 = ID 7 121 -­‐ 135 = ID 8 136 -­‐ 150 = ID 9 151 -­‐ 165 = ID 10 166 -­‐ 180 = ID 11 181 -­‐ 195 = ID 12 STAND ALONE OFFLINE MODE (NO DMX REQUIRED) 196 -­‐ 210 = ID 13 211 -­‐ 225 = ID 14 226 -­‐ 240 = ID 15 241 -­‐ 255 = ID 16 76 -­‐ 90 = ID 5 255 0
CH 14 Emitter Power
Strobe -­‐ Color Wheel Channel 1 > 0; Channel 5 > 146; Channel 6 = 4 to 15 1 -­‐ 25 26 -­‐ 75 76 -­‐ 125 126 -­‐ 175 176 -­‐ 255 10% 20% 40% 80% 100% First, set dip switch pin 10 to off. Emider will not require DMX input commands and no DMX controls or XLR cable are necessary. Only AC power is required to operate emider in stand alone beacon mode. See "Stand Alone Mode Dip Switch Seings" chart at lower lem for control seing opcons. *Functional only on Wink devices equipped with optional buzzer.
STAND ALONE OFFLINE MODE DIP SWITCH SETTINGS (No DMX Required)
Pin
10
1
2
3
4
5
6
7
8
9
Function
OFF = Stand Alone Mode ON = DMX Mode (use Pins 1-­‐9 to address)
Pins 1-­‐3 determine power (Off-­‐Off-­‐Off = 100%, On-­‐Off-­‐Off = 80%, Off-­‐On-­‐Off = 40%, Off-­‐Off-­‐On = 20%, On-­‐Off-­‐On = 10%)
Blink at rate 500ms on / 500ms off
Pulse at rate 250ms on / 250ms off; Both Pin 4 & 5 on changes to 500ms on/off
TBD Future Function
Red
Green
Blue
Version v0.08, 3-­‐14-­‐14
DMX 512 MODE DIP SWITCH ADDRESSING CHART
Pin
10
1
2
3
4
5
6
7
8
9
Values
On
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
Function
Standard DMX Mode
DMX starting address bit 1 (Least Significant Bit)
DMX starting address bit 2
DMX starting address bit 3
DMX starting address bit 4
DMX starting address bit 5
DMX starting address bit 6
DMX starting address bit 7
DMX starting address bit 8
DMX starting address bit 9 (Most Significant Bit)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising