Sea gull lighting | 77625-962 | Installation guide | Sea Gull Lighting 77625-962 Installation Guide

Installation And Safety Instructions
HC-1565
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
IMPORTANT SAFETY INSTRUCTIONS
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
•
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
•
To reduce the risk of fire, electric shock, or personal injury, mount to
outlet box or supporting system able to support the weight of the
fixture.
•
If you are unclear as to how to proceed, contact a qualified
electrician.
•
You don’t need special tools to install this fixture.
•
Be sure to follow the steps in the order given.
•
Under no circumstances should a fixture be hung on house electrical
wires, nor should a swag type fixture be installed on a ceiling which
contains a radiant type heating system.
•
Read instructions carefully.
•
Save these instructions.
083109
GROUNDING AND MOUNTING
BAR LOCK UP (FLUSH MOUNT)
*OUTLET BOX
*GROUND WIRE
*WIRE
CONNECTORS
GREEN
GROUNDING
SCREW (D)
*OUTLET BOX
SCREWS
FIGURE 2
OFFSET
MOUNTING
BAR (N)
MOUNTING
SCREWS (K)
*NOT INCLUDED
CLEANING
*OUTLET BOX
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
*GROUND WIRE
*WIRE
CONNECTORS
NIPPLE (C)
MOUNTING
BAR (A)
*OUTLET BOX
SCREWS
CANOPY (H)
SCREW COLLAR
RING (G)
SCREW
COLLAR (E)
NUT (B)
CHAIN (S)
STEP 1:
Thread fixture loop (I) to fixture (if applicable).
FIXTURE
LOOP (I)
ARMS (J)
BALL
NUTS (F)
DIFFUSER (O)
BOTTOM NIPPLE (P)
FINIAL (L)
FIGURE 1
*NOT SUPPLIED
INSTALLATION
HC-1565
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
FOR CHAIN HUNG
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 5 threads are exposed
above nut (B). Thread nipple (C) into mounting bar (A) and secure
with nut (B). Thread screw collar (E) to nipple (C).
STEP 2:
Using 2 pairs of pliers or chain breaks, open one link of chain (S) and
connect it to the fixture loop (I) at the top of the fixture. Please be
sure to open chain link in an outward motion.
STEP 3:
Slide the screw collar ring (G) and canopy (H), in that order, over
chain (S). Open one link on the other end of the chain (S) and attach
it to the screw collar (E) which has been mounted to the ceiling
nipple (C). BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
FOR FLUSH MOUNT
STEP 1:
Thread mounting screws (K) into offset mounting bar (N). Run
mounting screws (K) all the way down to their heads. Secure offset
mounting bar (N) to the outlet box (raised side to top as illustrated)
using outlet box screws (not supplied).
STEP 2:
Remove fixture loop (I) from fixture. Feed fixture wires through center
of flush canopy. Secure flush canopy to fixture by installing lock
washer and nut over center nipple.
WIRING
STEP 1:
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
STEP 2:
GROUNDING INSTRUCTIONS:
Connect the supply ground wire, fixture ground wire, and mounting bar
ground wire (pre attached) using the supplied wiring connector. Gently try
to remove the wires from the connector. If you can remove the wires,
carefully re-do the wiring connection.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1: CHAIN HUNG ONLY
Make sure no bare wires can be seen outside wire connectors. After
wires are connected, tuck them carefully inside outlet box. Push the
fixture firmly over the mounting screws (F) and against the wall.
Secure canopy (I) in place with cap nuts (E).
STEP 2: FLUSH MOUNT ONLY
Place flush canopy to ceiling so mounting screws (K) protrude
through flush canopy and secure by threading cap nuts to mounting
screws (K).
STEP 3:
Install lamps.
STEP 4:
Raise diffuser (O) over bottom nipple (P) and secure by placing
decorative cup (M) to diffuser (O), and threading finial (L) to bottom
nipple (P). Arms (J) should protrude through diffuser (O). Thread ball
nuts (F) onto arms to secure.
Download PDF