Sea Gull Lighting 5328-962 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
BEFORE YOU BEGIN
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
NOTE: FOR FIXTURES PROVIDED WITH 75° C OR
90° C SUPPLY WIRE WARNING ONLY-(THESE
WARNINGS ARE PROVIDED ON THE U.L. LABEL
AND ON THE FIXTURE CARTON): RISK OF FIRE.
MOST DWELLINGS BUILT BEFORE 1985 HAVE
SUPPLY WIRE RATED 60° C. CONSULT A
QUALIFIED ELECTRICIAN BEFORE INSTALLING.
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
GROUNDING AND MOUNTING
BAR LOCK UP
*OUTLET BOX
*GROUND WIRE
*WIRE
CONNECTORS
*WIRE
CONNECTOR
*OUTLET BOX
MOUNTING
BAR (A)
*OUTLET
BOX
SCREWS
*GROUND
WIRE
MOUNTING
BAR (A)
*OUTLET
BOX SCREWS
FIGURE 2
GREEN
GROUNDING
SCREW (D)
NUT (B)
NIPPLE (C)
*NOT SUPPLIED
NUT (B)
NIPPLE (C)
CANOPY
(Z)
CENTER
HOLE
(K)
RETAINING
SCREW (E)
CAP NUT (F)
Installation And
Safety Instruction
HC-167
051908
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
DIFFUSER (G)
FIGURE 1
*NOT INCLUDED
Fill In Item Number On Carton And
File This Sheet For Fixture Reference.
ITEM#_______________
HC-167
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are exposed
above nut (B). Thread nipple (C) into mounting bar (A) and secure
with nut (B).
STEP 2:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according to
the directions below:
STEP 3:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (M) from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (D) on the
mounting bar (A) if uninsulated wire is on the mounting bar (A),
connect the ground wire (M) from the fixture (if supplied) and the
outlet box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 4:
Thread three diffuser retaining screws (E) in side of canopy (Z).
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside outlet box.
Raise canopy (Z) to the ceiling allowing for nipple (C) to protrude
through center hole (K) in canopy (Z). Secure in place by
tightening cap nut (F).
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
STEP 2:
Install lamp (s).
STEP 3:
Raise diffuser (G) to canopy (Z) and finger tighten retaining screws
(E).
WHITE OR GREY WITH TRACER
WHITE OR GREY WITHOUT TRACER
CLEANING
BROWN, GOLD OR BLACK WITHOUT
TRACER
BROWN, GOLD OR BLACK WITH TRACER
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp the
ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.