Sea Gull Lighting 75520-845 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
NOTE: FOR FIXTURES PROVIDED WITH 75˚C OR 90˚C
SUPPLY WIRE WARNING ONLY-(THESE WARNINGS ARE
PROVIDED ON THE LABEL AND ON THE FIXTURE
CARTON): RISK OF FIRE. MOST DWELLINGS BUILT BEFORE
1985 HAVE SUPPLY WIRE RATED 60˚C. CONSULT A
QUALIFIED ELECTRICIAN BEFORE INSTALLING.
GROUNDING AND MOUNTING
BAR LOCK UP
*OUTLET BOX
*OUTLET BOX
*OUTLET BOX
SCREWS
*GROUND WIRE
MOUNTING
BAR (A)
*WIRE
CONNECTORS
FIXTURE
MOUNTING
SCREWS (I)
NUT (B)
LOCK
WASHER
(F)
MOUNTING
BAR (A)
MOUNTING
SCREWS (I)
*WIRE
CONNECTORS
CANOPY (E)
FIGURE 2
GREEN
GROUNDING
SCREW (D)
*OUTLET BOX
SCREWS
*NOT INCLUDED
COUPLING (M)
KEYSLOTS (N)
HEX NUT (Z)
CENTER
PIPE (G)
DIFFUSER (H)
FIGURE 1
WASHER & HEX NUT (Y)
FINIAL (L)
*NOT SUPPLIED
Installation And
Safety Instructions
HC-1155
070307
File This Sheet For Future Reference.
ITEM#_______________
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
ASSEMBLY
HC-1155
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1 & 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
STEP 1:
Thread hex nut (Z) onto center pipe (G). Thread this end of center
pipe into coupling (M) and secure with hex nut (Z).
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (D) on the
mounting bar (A). If uninsulated ground wire is on the mounting bar,
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied) (See Figure 2).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Raised side is top as illustrated.
STEP 2:
Thread fixture mounting screws (I) into threaded holes of mounting
bar (A) 3 turns each.
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 1:
After wires are connected, tuck them carefully inside outlet box.
Raise the canopy (E) to the ceiling allowing for mounting screws (I)
to protrude through key slots (N). Rotate canopy (E) clockwise until
screws (I) are in narrow part of keyslot (N). Tighten screws (I) with
screwdriver.
STEP 2:
Install lamps.
STEP 3:
Raise diffuser (H) to canopy so that center pipe (G) protrudes
through hole in diffuser (H). Secure in place by threading washer
and hex nut (Y) and finial (L) to center pipe (G).
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. Do Not twist wires
together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread
the connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above, and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from
the outlet box in the same manner.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.