Sea Gull Lighting 77474-782 Installation Guide

Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
120308
ORDERING PARTS
Be sure the electricity to the system you are working on is turned off;
either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing and
create a potential safety hazard.
To reduce the risk of fire, electric shock, or personal injury, mount to
outlet box or supporting system able to support the weight of the
fixture.
If you are unclear as to how to proceed, contact a qualified electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house electrical
wires, nor should a swag type fixture be installed on a ceiling which
contains a radiant type heating system.
Read instructions carefully.
Save these instructions.
•
HC-1456
CLEANING
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 5 threads are exposed
above nut (B). Thread nipple (C) into mounting bar (A) and secure
with nut (B).
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
CHAIN
HUNG
*WIRE
CONNECTORS
*OUTLET BOX
UNIVERSAL
MOUNTING
BAR (A)
NIPPLE (C)
NUT (B)
CANOPY (H)
FLUSH
MOUNT
*WIRE
CONNECTORS
*OUTLET BOX
UNIVERSAL
MOUNTING
BAR (A)
NIPPLE (C)
*GROUND WIRE
NUT (B)
SCREW
COLLAR
RING (G)
CAPNUT (K)
*GROUND WIRE
FLUSH
CANOPY (R)
CHAIN (S)
CAPNUT (K)
FIGURE 1
FIXTURE
LOOP (I)
FLUSH
CANOPY (R)
DIFFUSER (O)
*NOT SUPPLIED
DIFFUSER (O)
FIGURE 2
*NOT SUPPLIED
INSTALLATION
HC-1456
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
FOR CHAIN HUNG – SEE FIGURE 1
STEP 1:
Thread screw collar (E) to nipple (C).
STEP 2:
Using 2 pairs of pliers or chain breaks, open one link of chain (S) and
connect it to the fixture loop (I) at the top of the fixture. Chain should
open outward and should not be twisted.
STEP 3:
Slide the screw collar ring (G) and canopy (H), in that order, over
chain (S). Open one link on the other end of the chain (S) and attach
it to the screw collar (E) which has been mounted to the nipple (C).
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
WIRING
STEP 1:
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1: CHAIN HUNG ONLY
Make sure no bare wires can be seen outside wire connectors. After
wires are connected, tuck them carefully inside outlet box. Place the
canopy (H) to the ceiling, and thread the screw collar ring (G) to the
screw collar (E).
STEP 2: FLUSH MOUNT ONLY
Place flush canopy (R) to ceiling so nipple (C) protrudes through flush
canopy (R) and secure by threading cap nut to nipple (C).
STEP 3:
Install lamps.
STEP 4:
Raise diffuser (O) to fixture so holes in diffuser (O) line up with holes
in mounting brackets (P). Thread retaining screws (N) through diffuser
(O) into mounting brackets (P) to secure.
STEP 5:
Place top diffuser (J) onto mounting area so holes align. Place
washer on each top diffuser (J) hole, and thread top diffuser retaining
screws (R) through top diffusers (J) to secure.
STEP 2:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (F) from the fixture and the
ground wire from the outlet box (bare metal or green insulated wire)
around the green grounding screw (D) on the mounting bar (A) if
uninsulated wire is on the mounting bar (A), connect the ground wire
(F) from the fixture and the outlet box to it using a small wire
connector (not supplied). NEVER CONNECT GROUND WIRE TO
BLACK OR WHITE POWER SUPPLY WIRES.
DIFFUSER
(O)
TOP
DIFFUSERS
(J)
MOUNTING
BRACKETS
(P)
FIGURE 3
TOP
DIFFUSER
RETAINING
SCREWS (R)
RETAINING
SCREWS (N)
*NOT INCLUDED