Sea Gull Lighting 75850-782 Installation Guide

Installation And Safety Instructions
HC-1303
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
112408
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
*OUTLET BOX
SCREWS
*OUTLET BOX
MOUNTING
BAR (A)
FIXTURE
MOUNTING
SCREWS (I)
NOTE: FOR FIXTURES PROVIDED WITH 75˚C OR 90˚C SUPPLY WIRE
(FOUND ON CARTON LABEL) WARNING ONLY: RISK OF FIRE. MOST
DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED 60˚C.
CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING.
GREEN
GROUNDING
SCREW (D)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
CANOPY (E)
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
COUPLING (M)
KEYSLOTS (N)
HEX NUT (B)
CENTER
PIPE (G)
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
STEP 1:
Thread center pipe (G) and hexnut (B) into coupling (M).
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 2:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Raised side is top as illustrated.
DIFFUSER (H)
SUPPORT CUP
BOTTOM NUT &
LOCKWASHER (C)
FINIAL (L)
STEP 3:
Thread fixture mounting screws (I) into threaded holes of mounting
bar (A) 3 turns each.
FIGURE 1
*NOT SUPPLIED
INSTALLATION (continued)
HC-1303
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 4:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
STEP 6:
After wires are connected, tuck them carefully inside outlet box.
Raise the canopy (E) to the ceiling allowing for mounting screws (I) to
protrude through key slots (N). Rotate canopy (E) clockwise until
screws (I) are in narrow part of keyslot (N). Tighten screws (I) with
screwdriver.
STEP 7:
Install lamps.
STEP 8:
GROUP A:
CONNECT TO BLACK HOUSE WIRE
GROUP B:
CONNECT TO WHITE HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped or
ridged and less tracer wire is round in shape or smooth
(Seen best when viewed from wire end). To separate wires, grasp the
ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector, If you can
remove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
STEP 5:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire from the fixture and the
ground wire from the outlet box (bare metal or green insulated wire)
around the green grounding screw (D) on the mounting bar (A). If
uninsulated ground wire is on the mounting bar (A), connect the
ground wire from the fixture and the outlet box to it using a small
wire connector (not supplied) (See Figure 2).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
Raise diffuser (H) to canopy so that center pipe (G) protrudes
through hole in diffuser (H). Secure in place by threading bottom
lockwasher and hexnut (C), support cup (O), and finial (L) onto
center pipe (G).