Sea gull lighting | 75661-839 | Installation guide | Sea Gull Lighting 75661-839 Installation Guide

Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-1438
112608
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
NOTE: FOR FIXTURES PROVIDED WITH 75˚C OR 90˚C SUPPLY WIRE
WARNING ONLY-(THESE WARNINGS ARE PROVIDED ON THE LABEL
AND ON THE FIXTURE CARTON): RISK OF FIRE. MOST DWELLINGS
BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED 60˚C. CONSULT A
QUALIFIED ELECTRICIAN BEFORE INSTALLING.
*OUTLET BOX
SCREWS
*OUTLET BOX
MOUNTING
BAR (A)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
GREEN
GROUNDING
SCREW (D)
*WIRE
CONNECTORS
CANOPY (E)
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
FIXTURE
MOUNTING
SCREWS (B)
KEYSLOTS (C)
DECORATIVE RING (G)
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Raised side is top as illustrated.
DIFFUSER (F)
CAP NUTS (H)
STEP 2:
Thread fixture mounting screws (B) into threaded holes of mounting
bar (A) 3 turns each.
FIGURE 1
*NOT SUPPLIED
INSTALLATION (continued)
HC-1438
STEP 3:
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (D) on the
mounting bar (A). If uninsulated ground wire is on the mounting bar,
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied) (See Figure 2).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 5:
After wires are connected, tuck them carefully inside outlet box.
Raise the canopy (E) to the ceiling allowing for mounting screws (B)
to protrude through key slots (C). Rotate canopy (E) clockwise until
mounting screws (B) are in narrow part of keyslot (C). Tighten
mounting screws (B) with screwdriver.
STEP 6:
Install lamps.
STEP 7:
Place diffuser (F) into decorative ring (G). Place decorative ring (G)
to canopy (E) so mounting studs protrude through decorative ring
(G). Secure by threading cap nuts (H) to mounting studs.
Download PDF