Sea gull lighting | 8814-12 | Installation guide | Sea Gull Lighting 8814-12 Installation Guide

HC-329
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
100101
ASSEMBLY
FOR YOUR SAFETY
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF; EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER SET AT OFF.
STEP 1:
GENERAL
(If applicable):
Install tail assembly (B) to cage (A). Secure with finial (C).
You don't need special tools to install this fixture. Be sure to follow
the steps in the order given. Under no circumstances should a
fixture be hung on house electrical wires, nor should a swag type
fixture be installed on a ceiling which contains a radiant type heating
system. Read instructions carefully. If you are unclear as to how
to proceed, consult a qualified electrician.
STEP 1:
(If applicable):
Install top assembly (I) to roof (H). Secure with roof finial (J).
FIGURE 1
* NOT SUPPLIED
ROOF FINIAL (J)
* OUTLET BOX
* WIRE
CONNECTOR
TOP ASSEMBLY (I)
ROOF (H)
ROOF
SCREWS (L)
NUT (E)
GROUNDING AND MOUNTING BAR LOCK UP
NIPPLE (F)
BACKPLATE (K)
CAP NUT (M)
CAGE (A)
*OUTLET BOX
TAIL ASSEMBLY (B)
NUT (E)
GREEN
GROUNDING
SCREW (G)
NIPPLE (F)
FINIAL (C)
*OUTLET BOX
SCREWS
*GROUND WIRE
*NOT INCLUDED
MOUNTING BAR (D)
*WIRE CONNECTORS
FIGURE 2
INSTALLATION
HC-329
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Secure mounting bar (D) to outlet box with outlet box screws (not
supplied). Thread nut (E) on nipple (F) so that 3 threads are
exposed above nut (E). Thread nipple (F) into mounting bar (D) and
secure with nut (E).
STEP 2:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 3:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (D). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (G) on the
mounting bar (D) if uninsulated wire is on the mounting bar (D),
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied).
NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to
have ground wires. These fixtures still meet all U.L. specifications.
The listing mark of Underwriters on the product identifies products
manufactured under its listing and Follow-Up Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After the wires are connected, tuck them carefully inside the outlet
box. Push the backplate (K) firmly over the mounting nipple (F) and
against the wall. Secure in place with cap nut (M).
STEP 2:
Install diffuser panels (texture side in - if applicable) into cage (A).
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
NOTE: (If applicable)
There is a variation in all castings - in some cases the glass panels
may be slightly loose when installed - you may want to tape it in
place. Two (2) sided tape has been supplied for this purpose remove protective paper from each side of tape - place on upper
end of glass - install and press against casting.
WHITE OR GREY WITHOUT TRACER
Install candle cover (If applicable).
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
STEP 3:
WHITE OR GREY WITH TRACER
STEP 4:
BROWN, GOLD OR BLACK WITHOUT
TRACER
BROWN, GOLD OR BLACK WITH TRACER
Install lamps.
STEP 5:
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
Place roof (H) onto cage (A) and secure in place with roof
screws (L).
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
WET LOCATION
NOTE: FOR FIXTURES LABELED FOR WET LOCATION AND
USED OUTDOORS.
CAUTION: To reduce the risk of electrical shock, provide a
watertight seal between the fixture and the mounting surface by
using a silicone or similar caulking.
Download PDF