Sea gull lighting | 88882BLE-51 | Installation guide | Sea Gull Lighting 88882BLE-51 Installation Guide

Installation And Safety Instructions
HC-1507
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
112508
CLEANING
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
NOTE: This glass is handcrafted, the slight imperfections in the
glass add to the authenticity of the fixture.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
WET LOCATION
NOTE: FOR FIXTURES LABELED FOR WET LOCATION AND
USED OUTDOORS.
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
NOTE: TO KEEP YOUR SOLID POLISHED BRASS FIXTURE LOOKING
NEW FOR YEARS TO COME, REGULARLY APPLY A GOOD QUALITY
NON-ABRASIVE CAR WAX TO ALL METAL SURFACES, GIVING THE
FIXTURE AN EXTRA PROTECTIVE COATING.
CAUTION: To reduce the risk of electrical shock, provide a
watertight seal between the fixture and the mounting surface by
using a silicone or similar caulking.
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
*OUTLET BOX
MOUNTING
SCREWS (B)
UNIVERSAL
MOUNTING
BAR (A)
GREEN
GROUNDING
SCREW (H)
GLASS (E)
*WIRE
CONNECTORS
FIGURE 1
*OUTLET BOX
SCREWS
*NOT INCLUDED
INSTALLATION
HC-1507
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
Insert fixture mounting screws (B) in threaded holes of universal
mounting bar (A). Run mounting screws (B) all the way down to the
heads.
STEP 2:
Place universal mounting bar (A) against outlet box (not supplied) and
secure in place using outlet box screws (not supplied). Be sure the
mounting screws (B) are perfectly horizontal so fixture hangs straight.
STEP 3:
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (H) is to
be inserted into the hole with two raised dimples provided on the
universal mounting bar (A). Wrap the ground wire from the fixture (if
supplied) and the ground wire from the outlet box (bare metal or
green insulated wire) around the green grounding screw (H) on the
universal mounting bar (A). If uninsulated ground wire is on the
universal mounting bar (A), connect the ground wire from the fixture
(if supplied) and the outlet box to it using a small wire connector
(not supplied) (See Figure 2). NEVER CONNECT GROUND WIRE
TO BLACK OR WHITE POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside the outlet box.
Position backplate (C) over mounting screws (B) and secure in place
by threading cap nuts on to mounting screws (B).
STEP 2:
Install lamp.
Download PDF