Sea gull lighting | 79340BLE-780 | Installation guide | Sea Gull Lighting 79340BLE-780 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
NOTE: FOR FIXTURES PROVIDED WITH 75°C OR 90°C
SUPPLY WIRE WARNING ONLY: RISK OF FIRE. MOST
DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE
RATED 60°C. CONSULT A QUALIFIED ELECTRICIAN
BEFORE INSTALLING.
GROUNDING AND MOUNTING
BAR LOCK UP
*OUTLET BOX
*OUTLET BOX
CANOPY (E)
*OUTLET BOX
SCREWS
NUT (B)
MOUNTING
BAR (A)
*GROUND WIRE
FIXTURE
MOUNTING
SCREWS (I)
*WIRE
CONNECTORS
LOCK
WASHER
(F)
MOUNTING
BAR (A)
MOUNTING
SCREWS (I)
KEYSLOTS (N)
FIGURE 2
RETAINING SCREW /
BALL NUT (G)
GREEN
GROUNDING
SCREW (D)
DIFFUSER (H)
Installation And
Safety Instructions
HC-1372
FINIAL (L)
052808
File This Sheet For Future Reference.
FIGURE 1
*OUTLET BOX
SCREWS
*NOT INCLUDED
*NOT SUPPLIED
ITEM#_______________
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
BEFORE YOU BEGIN
HC-1372
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1 & 2. Be careful not to misplace any
of the screws or parts which are needed to install this fixture.
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire from the fixture and the
ground wire from the outlet box (bare metal or green insulated wire)
around the green grounding screw (D) on the mounting bar (A). If
uninsulated ground wire is on the mounting bar (A), connect the
ground wire from the fixture and the outlet box to it using a small wire
connector (not supplied) (See Figure 2).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Raised side is top as illustrated.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 2:
Thread fixture mounting screws (I) into threaded holes of mounting
bar (A) 3 turns each.
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 1:
After wires are connected, tuck them carefully inside outlet box.
Raise the canopy (E) to the ceiling allowing for mounting screws (I)
to protrude through key slots (N). Rotate canopy (E) clockwise until
screws (I) are in narrow part of keyslot (N). Tighten screws (I) with
screwdriver.
STEP 2:
Hold lamp (Q) by base and gently twist into socket (R) to install.
STEP 3:
Raise diffuser (H) to canopy (E) so that screw holes line up with
screws protruding from canopy (E). Secure in place by threading ball
nuts / retaining screws (G) through diffuser onto canopy (E) screws.
CLEANING
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when ordering
parts.
*NOTE: When parallel wire is used, the tracer wire is square shaped or
ridged, and the less tracer wire is round in shape or smooth. (Seen best
when viewed from wire end.) To separate wires, grasp the ends of each
wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against the
black wire from the outlet box. Do Not twist wires together before
using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above, and check
again for a firm connection.
ONE PIECE
LAMP/BALLAST
COMBINATION
ONE PIECE LAMP/
BALLAST
COMBINATION (Q)
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
Hg
MARK MEANS LAMP CONTAINS MERCURY.
FOLLOW DISPOSAL LAWS.
SEE WWW.LAMPRECYCLE.ORG
SOCKET (R)
FIGURE 3
Download PDF