Sea gull lighting | 82950PBL-12 | Installation guide | Sea Gull Lighting 82950PBL-12 Installation Guide

Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-1385
063008
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be installed on a ceiling
which contains a radiant type heating system.
Read instructions carefully.
Proper wiring is essential for the safe operation of this fixture.
Do not install on a post of a pole that results in a vertical rise of 25
feet or higher.
Save these instructions.
FINIAL (A)
THREADED
SCREW (R)
HOOD (C)
CAUTION:
Fixtures with photo-cells should be mounted at least 48"
from all sides to avoid reflection of light back onto Photocell, causing the Photo-cell to malfunction or flicker.
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
Your handcrafted, solid brass lighting fixture has been
coated with a durable, baked on acrylic lacquer which gives
maximum protection against the weather. In time, however,
the brightness of the brass will tarnish giving way to an
authentic old world brass finish.
NOTE: To keep your solid polished brass fixture looking new
for years to come, regularly apply a good quality nonabrasive car wax to all metal surfaces, giving the fixture an
extra protective coating.
CAGE (O)
GLASS (M)
ASSEMBLY
STEP 1:
Install glass (M) into fixture cage (O) (if applicable).
FITTER (F)
FIGURE 1
*NOT SUPPLIED
INSTALLATION
HC-1385
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
STEP 1:
Install lamp (D) into socket (E) by gently twisting into place.
STEP 2:
Install hood (C) to fixture body with threaded screws (R).
STEP 3:
Thread finial (A) onto nipple protruding from hood (C).
CLEANING
GROUP A:
CONNECT TO BLACK HOUSE WIRE
GROUP B:
CONNECT TO WHITE HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. Do Not twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above, and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
STEP 2:
GROUND INSTRUCTIONS:
Connect the ground wire from the fixture (bare metal or green
insulated wire) to the ground wire from the power supply (bare metal
or green insulated wire) using a small wire connector (not supplied).
FIXTURES WITH A ONE PIECE
LAMP / BALLAST COMBINATION
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
LAMP (D)
STEP 3:
Slide fitter (F) onto post. Secure in place with screws.
SOCKET (E)
Hg
MARK MEANS LAMP CONTAINS MERCURY.
FOLLOW DISPOSAL LAWS.
SEE WWW.LAMPRECYCLE.ORG
FIGURE 2
Download PDF

advertising