Sea Gull Lighting 89240BL-780 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
•
FINIAL (A)
•
•
HOOD (E)
•
•
•
•
•
CAGE
SCREWS (G)
NIPPLE
(C)
CAP
NUTS (F)
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
Do not install on a post or pole that results in a vertical rise of 25
feet or higher.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Proper wiring is essential for the safe operation of this fixture.
To reduce the risk of fire, electric shock or personal injury, mount
to outlet box or supporting system able to support the weight of
the fixture.
Read instructions carefully.
Save these instructions.
NOTE: This glass is handcrafted, the slight imperfections in
the glass add to the authenticity of the fixture.
FITTER (B)
Installation And
Safety Instruction
HC-1370
053008
FIGURE 1
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
Fill In Item Number On Carton And
File This Sheet For Fixture Reference. ITEM#_______________
HC-1370
INSTALLATION
STEP 1:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
STEP 2:
GROUNDING INSTRUCTIONS:
Connect the ground wire from the fixture (bare metal or green
insulated wire) to the ground wire from the power supply (bare metal
or green insulated wire) using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK
OR WHITE POWER SUPPLY WIRES.
STEP 3:
Slide fitter (B) onto post. Secure in place with screws (not provided).
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
GROUP B: CONNECT TO WHITE
HOUSE WIRE
Install lamp (H) into socket (D) by holding lamp (H) by base and
twisting into socket (D) gently.
WHITE
STEP 2:
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. Do Not twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above, and
check again for a firm connection.
Install hood (E) allowing nipple (C) to protrude through hood. Secure
by threading finial (A) onto nipple (C). Thread cap nuts (F) onto cage
screws (G)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
ONE PIECE
LAMP/BALLAST
COMBINATION
ONE PIECE LAMP/
BALLAST
COMBINATION (H)
Hg
MARK MEANS LAMP CONTAINS MERCURY.
FOLLOW DISPOSAL LAWS.
SEE WWW.LAMPRECYCLE.ORG
SOCKET (D)
FIGURE 2