Sea Gull Lighting 8269-44 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
ASSEMBLY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be
hung on house electrical wires, nor should a swag type fixture be
installed on a ceiling which contains a radiant type heating system.
Read instructions carefully. If you are unclear as to how to proceed,
consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
STEP 1:
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1 & 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
WARNING
NOTE: DO NOT INSTALL ON A POST OR A POLE
THAT RESULTS IN A VERTICAL RISE OF 25 FEET
OR HIGHER.
NOTE: This glass is handcrafted, the slight
imperfections in the glass add to the
authenticity of the fixture.
FITTER (M)
RETAINING
SCREWS (X)
Installation And
Safety Instruction
*POST
DIFFUSER (B)
BRACKETS (G)
HC-534
092001
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
*NOT SUPPLIED
FIG. 1
Fill In Item Number On Carton And
File This Sheet For Fixture Reference.
ITEM#_______________
INSTALLATION
HC-534
STEP 2:
GROUNDING INSTRUCTIONS:
Connect the ground wire from the fixture (bare metal or green insulated wire) to the ground wire from the power supply (bare metal or
green insulated wire) using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK
OR WHITE POWER SUPPLY WIRES.
STEP 3:
Slide fitter (M) onto post. Secure in place with screws (not supplied).
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
Install lamps.
WHITE OR GREY WITH TRACER
WHITE OR GREY WITHOUT TRACER
STEP 2:
Thread through diffuser retaining screws (X) into holes at top of
fixture. Raise diffuser, and finger tighten screws.
BROWN, GOLD OR BLACK WITHOUT
TRACER
BROWN, GOLD OR BLACK WITH TRACER
STEP 3:
Snap on cage brackets (G).
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
STEP 1:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
B. Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. Do Not twist wires
together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw
the connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps B and C, as above, and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from
the outlet box in the same manner.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.