Sea gull lighting | 82007-71 | Installation guide | Sea Gull Lighting 82007-71 Installation Guide

HC-657
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
092010
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Proper wiring is essential for the safe operation of this fixture.
Save these instructions.
Your handcrafted, solid brass lighting fixture has been coated
with a durable, baked on acrylic lacquer which gives
maximum protection against the weather. In time, however, the
brightness of the brass will tarnish giving way to an authentic
old world brass finish.
NOTE: To keep your solid polished brass fixture looking new
for years to come, regularly apply a good quality non-abrasive
car wax to all metal surfaces, giving the fixture an extra
protective coating.
WARNING
NOTE: DO NOT INSTALL ON A POST OR A POLE THAT
RESULTS IN A VERTICAL RISE OF 25 FEET OR HIGHER.
NOTE: This glass is handcrafted, the slight imperfections in
the glass add to the authenticity of the fixture.
FINIAL (A)
HOOD (E)
CAGE (D)
SOCKET
COVERS (G)
FITTER (F)
FIGURE 1
INSTALLATION
HC-657
STEP 1:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 2:
GROUNDING INSTRUCTIONS:
Connect the ground wire from the fixture (bare metal or green
insulated wire) to the ground wire from the power supply (bare metal
or green insulated wire) using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK
OR WHITE POWER SUPPLY WIRES.
STEP 3:
Slide fitter (F) onto post. Secure in place with screws.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
Install socket cover (G) (if applicable).
STEP 2:
Install lamp.
STEP 3:
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. Do Not twist wires
together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread
the connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above, and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from
the outlet box in the same manner.
Install hood (E) onto nipple (S) and secure by threading finial (A)
onto nipple (S).
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
Download PDF