Sea gull lighting | 83046-714 | Installation guide | Sea Gull Lighting 83046-714 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
BEFORE YOU BEGIN
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
*OUTLET BOX
*WIRE
CONNECTOR
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
MOUNTING
BAR (D)
*OUTLET
BOX
SCREWS
NUT (E)
DIFFUSER (I)
NIPPLE (F)
*NOT INCLUDED
FIGURE 1
GROUNDING AND MOUNTING
BAR LOCK UP
*OUTLET BOX
GREEN
GROUNDING
SCREW (G)
NUT (E)
NIPPLE (F)
*OUTLET BOX
SCREWS
MOUNTING BAR (D)
013008
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
*GROUND WIRE
*WIRE CONNECTORS
*NOT INCLUDED
Installation And
Safety Instruction
HC-1338
FIGURE 2
Fill In Item Number On Carton And
File This Sheet For Fixture Reference.
ITEM#_______________
HC-1338
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Secure mounting bar (D) to outlet box with outlet box screws (not
supplied). Thread nut (E) on nipple (F) so that 3 threads are exposed
above nut (E). Thread nipple (F) into mounting bar (D) and secure
with nut (E).
STEP 2:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according to
the directions below:
STEP 3:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (D). Wrap the ground wire from the fixture (if supplied) and
the ground wire from the outlet box (bare metal or green insulated
wire) around the green grounding screw (G) on the mounting bar
(D) if uninsulated wire is on the mounting bar (D), connect the
ground wire from the fixture (if supplied) and the outlet box to it
using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After the wires are connected, tuck them carefully inside the outlet box.
Push the fixture firmly over the nipple (F) and against the wall. Secure in
place by threading cap nut onto nipple (F).
STEP 2:
Install lamps.
STEP 3:
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
If installing outdoors, be sure fixture opening is located at the bottom
and see “wet location” note below.
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
WET LOCATION
NOTE: FOR FIXTURES LABELED FOR WET LOCATION AND
USED OUTDOORS.
CAUTION: To reduce the risk of electrical shock, provide a watertight
seal between the fixture and the mounting surface by using a silicone
or similar caulking.
Download PDF

advertising