Worldwide Lighting Provence 3-Light Chrome with Black Crystal Sconce installation Guide

 W 23103C13-CL
D13 X8.5” HI8” L3
Е що 4
a =
ETS |
L
+
r
Г
x! EC
a
pa
Er
ARA ЧЩ
; a
alt ' 4 Y |
a À 3 13
t did $4 QE Fu
ha A a
$
у", - A ы ;
+ - it (= HL 1
В i = + A a Le
|. E ; 19 4 29
EE | 4 et] Ÿ ЗИ
Майя”. 2 ‘ к + X
PS 2 14 ,
COEUR Lv
Fi "181 |
"енг * ТИ |
раны = | 4 a
Te 4
e ni pee я
A
A
|
We are dedicated to providing the finest quality crystal
chandelier for our customers. Our master craftsmen and
designer pride themselves on their attention to detail.
prompt, efficient service 1s our priority.
Enclosed, are detailed instructions on how to properly
install your chandelier.Please read all instructions carefully
and thoroughly. If you have any questions please fell free
to call our toll free DHANDELIER HOTLINE AT:
1-855-411-8999
us
Crystal Dressing Instructions
When dressing the chandelier
W231 03C1 3-CL with the crystals please remember
to wear either rubber or cotton
gloves. So as to prevent any
damage or smudging on the crystals.
> 14mmX2
AL
- ad
RS
8 14mmX7
| ss |
Y
de
A 3) <UmmA 1
O) E lstring
CANOPY PARTS LIST
Wire Connector
Shrinkable tube
Cable tie
Ground Wire
CANOPY INSTALLATION DIAGRAM
Frame Parts List
02-Lamp Boby
05. 06 (Metal Finial)
NJ
07-Glass Saucer
WARNING!!!
CONTENTS ARE FRAGILE
HANDLE WITH CARE
The metal frame and crystal components of this chandelier are
very delicate. Please excersise extreme Caution during
unpacking and installation.
WARNING!!!
After passing the main eiectrical wire through the 10mm pipe
and connecting the pipe to the main body top connector, place
all remaining pieces as shown in nurmerical order and in the
orientation depicted. Refer to the parts list to avoid
confusion between parts. The part Numbers coincide
CAUTION
1. Rated 110v-130v/60Hz, bulb E12/40W maximum.
2. Care Should be taken to avoid damage to the surface of lighting
and wire, wearing gloves is recommended when installing
3. Connect black or red wire of the lighting to live wire and white
or blue wire to neutral wire and double colored(or bare
copper)wire to ground wire.
4. Never install lighting on damp ceiling, the room should be dry
and well ventilated.
5. Keep lighting away from acid, alkali and other corrosive chemical
or gas, clean the lighting with Clean soft cloth only.
6. Installation must be carried out by qualified electrician only.
7. Disconnect the power before installing, Ceaning and replacing
lighting.
8. Never cover the lighting when power is connected.
9. Firmness must be secured when installing ceiling
tube. chain. pipe and other connecting parts.
10. Care should be taken to avoid damage when installing glass
parts.
11. А11 electrical components must be installed by a licensed
electrician and in accordance with the National Electrical Code
and the appropriate local electrical codes. Make sure that
the elecrtrical supply to the chandellier is turned off at the
main fuse or circuit breaker before doing any installation Worldwide
lighting shall not be responsible for unprofessional wiring.
Crystal Dressing Diagram
When dressing the chandelier
with the crystals please remember
to wear either rubber or cotton
gloves. So as to prevent any
damage or smudging on the crystals.
o
)
Y
Aa
)
UD
= a A £ à A
AR y ns
4
pd BE
Y Va
e a 2
BON e
MN Y MN B
A KE HN +
E TE Ca
Y @ % À 99 NZ
A SZ A С
UN X ZN
“am a ол -—
yv 8& \ 4
AN
ATAVA
Y YN
УИ Е
WAVY
wr
Frame Assembly Diagragram
Y
a —
NAAA
WAS PR YS
Nu
Sy a
|
AJ
ХР» АРТ
ЧУ UY \l/
7 A “TT Makin A
XA ¢ v= IN
К 7 || \ WD J [| \
Й N > SIA N
e UNE то
a, “a. >
() A my INR À A
7 CU VRP NA
=x; æ IS mo
YX A
w “я
CANOPY INSTALLATION INSTRUCTIONS
Please read all instructions carefuly. Before you proceed to
install, make sure that the power supply is turned off and
off until installation is complete.Please note that each part has
been asigned a letter.Please proceed in an alphabetical order.
A. Existing Electrical Box
B. Crossbar
C. Crossbar Screws
D. Metal Plate
E. Crossbar Bracket
F. Neutral Conductor
G. Hot Wire
H. Junction Caps
I. Ground Wire
J. Wire
Attach the Crossbar (B)to the existing electrical box (A)using
the two crossbar screws (E)which are not supplied and should
already be in your box.
WARNING!!!
CONTENTS ARE FRAGILE
HANDLE WITH CARE
The metal frame and crystal components of this chandelier are
very delicate. Please excersise extreme Caution during
unpacking and installation.
WARNING!!!
After passing the main eiectrical wire through the 10mm pipe
and connecting the pipe to the main body top connector, place
all remaining pieces as shown in nurmerical order and in the
orientation depicted. Refer to the parts list to avoid
confusion between parts. The part Numbers coincide
CAUTION
1. Rated 110v-130v/60Hz, bulb E12/40W maximum.
2. Care Should be taken to avoid damage to the surface of lighting
and wire, wearing gloves is recommended when installing
3. Connect black or red wire of the lighting to live wire and white
or blue wire to neutral wire and double colored(or bare
copper)wire to ground wire.
4. Never install lighting on damp ceiling, the room should be dry
and well ventilated.
о. Keep lighting away from acid, alkali and other corrosive chemical
or gas, clean the lighting with Clean soft cloth only.
6. Installation must be carried out by qualified electrician only.
7. Disconnect the power before installing, Ceaning and replacing
lighting.
8. Never cover the lighting when power is connected.
9. Firmness must be secured when installing ceiling
tube. chain. pipe and other connecting parts.
10. Care should be taken to avoid damage when installing glass
parts.
11.All electrical components must be installed by a licensed
electrician and in accordance with the National Electrical Code
and the appropriate local electrical codes. Make sure that
the elecrtrical supply to the chandellier is turned off at the
main fuse or circuit breaker before doing any installation World wide
lighting shall not be responsible for unprofessional wiring.
Frame Assembly Instructions
Installation:
Please read all instructions carefully.
Before you proceed to install, make sure.
that the power supply is turned off and
remains off until installation is complete.
please note that each part has been assigned a number.
please proceed in a numerical order.
Fix the Crossbar (01) with junction box
Make sure the positive and negative charges of wire and
Lamp Body (02) match correctly, screw the connect point
with the junction cap.
Make sure the main wire is enough long and keep the rest
wire in the 4” J-box.
As the crystal pressing instruction, hang the crystal parts
Install lighting Source.
The end!