Sea gull lighting | 60122BLE-820 | Installation guide | Sea Gull Lighting 60122BLE-820 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
BEFORE YOU BEGIN
Be sure the electricity to the system you are working on is turned off;
either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing and
create a potential safety hazard.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
If you are unclear as to how to proceed, contact a qualified electrician.
Save these instructions.
*OUTLET BOX
Carefully remove the fixture from the carton and check that all
parts are included, as shown in figure 1 and 2. Be careful not to
misplace any of the screws or parts which are needed to install
this fixture.
GROUNDING AND MOUNTING
BAR LOCK UP
*OUTLET BOX
*GROUND WIRE
*HOUSE
GROUND WIRE
*WIRE
CONNECTORS
GREEN
GROUNDING
SCREW (D)
NIPPLE (C)
*WIRE
CONNECTORS
MOUNTING BAR (A)
NUT (B)
*OUTLET BOX
SCREWS
MOUNTING
BAR (A)
CANOPY (G)
*OUTLET
BOX
SCREWS
SCREW
COLLAR (E)
SCREW COLLAR
RING (F)
CHAIN (H)
GREEN
GROUNDING
SCREW (D)
FIGURE 2
NUT (B)
NIPPLE (C)
*NOT INCLUDED
FIXTURE LOOP (H)
NIPPLE (J)
COUPLING (L)
Installation And Safety
Instruction
HC-1095 081307
Fill In Item Number On Carton And
File This Sheet For Fixture Reference.
GLASS WASHER (K)
*NOT SUPPLIED
RETAINING
RING (N)
FIGURE 1
ITEM#_______________
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
INSTALLATION
HC-1095
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are exposed
above nut (B). Thread nipple (C) into mounting bar (A) and secure
with nut (B). Attach screw collar (E) to nipple (C).
STEP 2:
Using 2 pairs of pliers, open one link of chain (P) and connect it to
the fixture loop (H) at the top of the fixture. (If applicable).
STEP 3:
Slide the screw collar ring (F) and canopy (G), in that order, over
chain (P). Open one link on the other end of the chain (P) and
attach it to the screw collar (E) which has been mounted to the
ceiling nipple (C). BE SURE TO CLOSE ALL CHAIN LINKS
COMPLETELY.
STEP 4:
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (M) from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (D) on the
mounting bar (A) if uninsulated wire is on the mounting bar (A),
connect the ground wire (M) from the fixture (if supplied) and the
outlet box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Lace wires up through chain (P) and pass wires through holes in
screw collar (E). We recommend lacing wire up through every other
link of chain (P).
STEP 5:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside outlet box.
Raise canopy (G) against ceiling and thread the screw collar ring (F)
to the screw collar (E).
STEP 2:
Raise glass (R) to socket. Place glass washer (K) around socket
and secure by threading retaining ring (N) onto socket.
STEP 3:
Install lamps.
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
*PARALLEL WIRE (ROUND & SMOOTH)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
Download PDF