mf/hf antenna model at-505-a
INVELCO S.A.
CATALOGUE
MF / HF
EQUIPMENT AND SYSTEMS FOR
RADIO COMMUNICATIONS
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
Ronda de Poniente 15, 28760 Tres Cantos, Madrid (SPAIN)
Tel. (+34) 918 032 444 Fax. (+34) 918 033 228
Web: www.invelco.com
e-mail: [email protected]
All Rights reserved. Under the copyright laws, this publication may not be reproduced or transmitted in
any form, electronic or mechanical, including pohotocopying, recording, storing in an information retrieval
system, or translating, whole or part, without prior consent of INVELCO S.A..
No responsability is assumed by the use of the information contained in this catalogue. Although all
INVELCO S.A. is not
responsible of any possible mistakes or omissions. Due to constant technical advance of INVELCO
S.A., the characteristics of the equipment included in this catalogue may be modified without previous
possible precautions have been taken in the preparation of this catalogue,
notice.
and INVELCO, are trademarks property of INVELCO S.A. Other bands and/or commercial
products that appear in this publication are trademarks or trade names of their respective companies.
® 1998 INVELCO S.A. All Rights reserved.
PRODUCT CATALOGUE
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
COUPLER FOR VERTICAL ANTENNAS IN
THE RANGE OF 1.6 A 30 MHZ. PREPARED
FOR OUTDOORS.
IT WORKS SIMULTANEOUSLY IN THREE
PRE-TUNED FREQUENCIES.
THREE COUPLING FREQUENCIES
COUPLER FOR VERTICAL ANTENNA
MODEL AC-160-A/F
IMPORTANT SPECIFICATIONS :
-
THREE COUPLING FREQUENCIES.
RANGE 1.6 TO 30 MHZ.
SIMULTANEOUS WORK OF THE THREE FREQUENCIES.
OPERATING POWER 6 KW.
INPUT IMPEDANCE 50 OHMS.
PREPARED FOR OUTDOORS.
Spanish
Production
Page 5-3
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE COUPLER FOR VERTICAL ANTENNA
MODEL AC-160-A/F
TECHNICAL SPECIFICATIONS
Frequency range .................................1.6 to 30 MHz.
Coupled frequency ..............................Three to one input of 50 Ohm.
Operating possibility ............................Simultaneous in three frequencies.
Input impedance ..................................50 Ohms.
Input connector ....................................7/16 H panel.
Output connector ................................AT special insulator.
Operating power ..................................4KW.
Type of tune ........................................Fixed in the determined frequencies.
Bandwidth ...........................................Approximate 40 KHz.
Maximum input ROE ...........................2:1 to any frequency typical 1.25:1
Fabrication ..........................................Outdoor watertight and thermally insulated.
Tune times ..........................................None once tuned.
Working temperature ..........................-50 ºC to +85 ºC.
Relative humidity .................................95%
Dimensions :
Width ..............................................80 cm.
Depth ..............................................40 cm.
Height .............................................100 cm.
Approximate weight .............................115 Kg.
Anchorage ...........................................4 screws 8*90
Finish ...................................................Brown textured colour.
Page 5-4
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
COUPLER FOR VERTICAL ANTENNAS IN
THE RANGE OF 1.6 A 30 MHZ. PREPARED
FOR OUTDOORS.
IT WORKS SIMULTANEOUSLY IN TWO
PRE-TUNED FREQUENCIES.
TWO COUPLING FREQUENCIES
COUPLER FOR VERTICAL ANTENNA
MODEL AC-160-B
IMPORTANT SPECIFICATIONS :
-
TWO COUPLING FREQUENCIES.
RANGE 1.6 TO 30 MHZ.
SIMULTANEOUS WORK OF THE TWO FREQUENCIES.
OPERATING POWER 4 KW.
INPUT IMPEDANCE 50 OHMS.
PREPARED FOR OUTDOORS.
Spanish
Production
Page 5-3
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE COUPLER FOR VERTICAL ANTENNA
MODEL AC-160-B
TECHNICAL SPECIFICATIONS
Frequency range .................................1.6 to 30 MHz.
Coupled frequency ..............................Two to one input of 50 Ohm.
Operating possibility ............................Simultaneous in two frequencies.
Input impedance ..................................50 Ohms.
Input connector ....................................7/16 H panel.
Output connector ................................AT special insulator.
Operating power ..................................4KW.
Type of tune ........................................Fixed in the determined frequencies.
Bandwidth ...........................................Approximate 40 KHz.
Maximum input ROE ...........................2:1 to any frequency typical 1.25:1
Fabrication ..........................................Outdoor watertight and thermally insulated.
Tune times ..........................................None once tuned.
Working temperature ..........................-50 ºC to +85 ºC.
Relative humidity .................................95%
Dimensions :
Width ..............................................80 cm.
Depth ..............................................40 cm.
Height .............................................100 cm.
Approximate weight .............................115 Kg.
Anchorage ...........................................4 screws 8*90
Finish ...................................................Brown textured colour.
Page 5-4
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
COUPLER FOR VERTICAL ANTENNAS IN
THE RANGE OF 1.6 A 30 MHZ. PREPARED
FOR OUTDOORS.
IT WORKS SIMULTANEOUSLY IN ONE
PRE-TUNED FREQUENCY.
ONE COUPLE FREQUENCY
COUPLER FOR VERTICAL ANTENNA
MODEL AC-160-C
IMPORTANT SPECIFICATIONS :
-
ONE COUPLING FREQUENCY.
RANGE 1.6 TO 30 MHZ.
OPERATING POWER 4 KW.
INPUT IMPEDANCE 50 OHMS.
PREPARED FOR OUTDOORS.
Spanish
Production
Page 5-3
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE COUPLER FOR VERTICAL ANTENNA
MODEL AC-160-C
TECHNICAL SPECIFICATIONS
Frequency range .................................1.6 to 30 MHz.
Coupled frequency ..............................One input of 50 Ohm.
Operating possibility ............................One frequency.
Input impedance ..................................50 Ohms.
Input connector ....................................7/16 H panel.
Output connector ................................AT special insulator.
Operating power ..................................4KW.
Type of tune ........................................Fixed in the determined frequency.
Bandwidth ...........................................Approximate 40 KHz.
Maximum input ROE ...........................2:1 to any frequency typical 1.25:1
Fabrication ..........................................Outdoor watertight and thermally insulated.
Tune times ..........................................None once tuned.
Working temperature ..........................-50 ºC to +85 ºC.
Relative humidity .................................95%
Dimensions :
Width ..............................................80 cm.
Depth ..............................................40 cm.
Height .............................................100 cm.
Approximate weight .............................115 Kg.
Anchorage ...........................................4 screws 8*90
Finish ...................................................Brown textured colour.
Page 5-4
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
RECEPCION COUPLING CELL FOR
VERTICAL ANTENNAS IN THE RANGE
OF 1,6 to 30 MHz.
ESPECIALLY
DESIGNED
FOR
OPERATING IN THE MF/HF BAND.
RECEPTION COUPLER FOR VERTICAL
ANTENNA MODEL AC-160-R
IMPORTANT SPECIFICATIONS:
- RANGE 1,6 TO 30 MHZ. (BROADBAND).
- INPUT IMPEDANCE 50 OHMS.
- ELECTRIC DISCHARGE COILS.
- PREPARED FOR OUTDOORS.
Spanish
Production
Page 5-9
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE COUPLER FOR VERTICAL ANTENNA
MODEL AC-160-R
TECHNICAL SPECIFICATIONS
Frequency range .................................1,6 TO 30 MHz.
Input impedance ..................................50 Ohms.
Input connector ....................................Stuffing box PG13.
Output connector ................................Pocelain/teflon insulator.
Electric discharge coils .......................32uH.
Type of tune ........................................None.
Fabrication ..........................................Watertight polystyrene box (external).
Mechanical internal box.
Operating temperature ........................-30 ºC to +85ºC.
Relative humidity .................................95%
Dimensions :
Width ..............................................36 cm.
Depth ..............................................54 cm.
Height .............................................18 cm.
Approximate weight .............................10 Kg.
Anchorage ...........................................4 screws 4x50
Page 5-10
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
COUPLER FOR VERTICAL ANTENNAS IN
THE RANGE OF 440 to 550 KHZ.
PREPARED FOR OUTDOORS.
ESPECIALLY DESIGNED FOR NAVTEX
OPERATING.
COUPLER FOR VERTICAL ANTENNA
MODEL AC-160-W
IMPORTANT SPECIFICATIONS :
- RANGE 400 TO 550 KHZ.
- OPERATING POWER 3 KW.
- INPUT IMPEDANCE 50 OHMS.
- PREPARED FOR OUTDOORS.
Spanish
Production
Page 5-5
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE COUPLER FOR VERTICAL ANTENNA
MODEL AC-160-W
TECHNICAL SPECIFICATIONS
Frequency range .................................440 TO 550 KHz.
Input impedance ..................................50 Ohms.
Input connector ....................................Panel 7/16 H.
Output connector ................................Special AT insulator.
Operating power ..................................3KW.
Type of tune ........................................Fixed in the particular frequencies.
Bandwidth ...........................................Approximate 10 KHz.
ROE maximum input ..........................2:1 at any frequency typical 1.25:1
Fabrication ..........................................Outdoor watertight and thermally insulated.
Tune times ..........................................None once tuned.
Working temperatures.........................-30 ºC to +85ºC.
Relative humidity .................................95%
Dimensions:
Width ..............................................80 cm.
Depth ..............................................40 cm.
Height .............................................100 cm.
Approximate weight .............................115 Kg.
Anchorage ...........................................4 screws 8*90
Finish ...................................................Brown textured colour.
Page 5-6
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
RECEPTION COUPLING CELL FOR
VERTICAL ANTENNAS IN THE RANGE
OF 1,6 to 3 MHz.
SPECIALLY
DESIGNED
FOR
OPERATING IN THE MF/HF BAND.
RECEPTION COUPLER FOR VERTICAL
ANTENNA MODEL AC-160-Y
IMPORTANT SPECIFICATIONS:
- RANGE 1,6 TO 3 MHZ. (BROADBAND).
- INPUT IMPEDANCE 50 OHMS.
- ELECTRIC DISCHARGE COILS.
- PREPARED FOR OUTDOORS.
Spanish
Production
Page 5-9
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE COUPLER FOR VERTICAL ANTENNA
MODEL AC-160-Y
TECHNICAL SPECIFICATIONS
Frequency range .................................1,6 TO 3 MHz.
Input impedance ..................................50 Ohms.
Input connector ....................................Stuffing box PG13.
Output connector ................................Porcelain/teflon insulator.
Coupler cell with earth discharge
Broadcasting (AM/FM) filter removal (optional)
Fabrication ..........................................Watertight polystyrene box (external).
Mechanical internal box.
Operating temperature ........................-30 ºC to +85ºC.
Relative humidity .................................95%
Dimensions :
Width ..............................................36 cm.
Depth ..............................................54 cm.
Height .............................................18 cm.
Approximate weight .............................10 Kg.
Anchorage ...........................................4 screws 4x50
Page 5-10
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
ADAPTATIVE A.L.E. CONTROL
UNIT
AUTOMATIC MANAGER OF HF
FREQUENCIES
CONTROL THROUGH RS-232-C
A.L.E. CONTROL UNIT
MODEL AE-100-A
The AE-100-A control unit allows to adapt the HF transceivers or transmitters/receivers
equipment to the adaptative protocols for A.L.E. (Automatic Link Establishment)
communications techniques.
It allows to simplify and optimize the radiocommunications that use the HF signals as a mean.
Its work in real time allows to optimize the channel to be used with the intention of obtaining the
better performance of the systems.
IMPORTANT SPECIFICATIONS:
- COMPATIBLE WITH STANDARDS:
FED-STD-1045
MIL-STD-188-141-A
- SCANNING FREQUENCY.
- SELECTIVE CALL.
- LINK QUALITY ANALYSIS.
- CHANNEL SOUNDING.
- HF TRANSCEIVER MANAGING, CONTROL AND GOVERNING.
- REMOTE CONTROL THROUGH RS-232-C.
Spanish
Production
- INPUTS / OUTPUTS, 600 OHMS IMPEDANCE.
Page 8-3
INVELCO S.A.
A.L.E. CONTROL UNIT
MODEL AE-100-A
GENERAL SPECIFICATIONS:
POWER SUPPLY:
- Standard: ...................................... FED-STD-1045 and
MIL-STD-188-141-A
- Power Supply: ............................ 220VAC. 40-60Hz.
- Consumption: .............................. 40 Watts.
- A.L.E. audio bandwith: ............... 500-2750Hz.
- A.L.E. tone frequency: ................ 750Hz; 1000Hz; 1250Hz;
1500Hz; 1750Hz; 2000Hz;
2250Hz; 2500Hz.
- Type of I/O audio: ...................... Balanced / Desbalanceado.
ENVIRONMENTAL SPECIFICATIONS:
- Operation temperature range: ...... -40ºC. to +65ºC.
- Humidity: .................................... 95%
- Audio I/O level: ........................... -10 to 0dBm.
- Audio input/output impedance: .. 600Ω.
- Channel scanning rate: ................. Selectable 2 or 5 channels/
second. Manual control
available.
- Listening Channel/Time: ............. For ALE detection yo need
100ms minimum of active
listening time per channel
(500ms total interval at 2
channels/second) (200ms
total interval at 5 channels/
second).
- Remote Control: ......................... RS-232-C, Bauds Speed
9.600; 19.200; 57.600;
115.200; selectable.
- Keyline/PTT I/O: ........................ Selectable theough software
command or I/O.
- HF Transceiver: .......................... Uses a a group of HF
transmitter model EM-512-D
and a receiver model RX-300A, and are governed by means
of RS-232-C
- A.L.E. indicatives: ...................... Possibility to define up to 20
indicatives.
- A.L.E. Stations indicatives: ........ Possibility to define up to 100
stations indicatives.
- A.L.E. Radio Channels: .............. Possibility to define 100
A.L.E. channels.
- A.L.E. channels group: ............... Possibility to define up to 10
channels groups.
Page 8-4
MECHANICAL SPECIFICATIONS:
- Width: .......................................... Rack 19''
- Height: ......................................... 1U
- Depth: ......................................... 320mm.
- Weight: ........................................ 3Kg.
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
HF ANTENNA
COVERAGE 2 TO 30 MHZ
(BROADBAND)
BROADBAND ANTENNA,
PASSIVE TYPE, WITH NO
ANTENNA COUPLER
2-30 MHZ. BROADBAND ANTENNA 1500W.
AT-105-A
This antenna, easy to install, is the ideal complement for fixed radiocommunication
equipment that use HF. band in discrete jumps. The absence of mobile or switching tune
elements guarantee that the tune time before a frequency change is null, therefore assures
that this antenna is the best solution for systems of scanner or A.L.E. type in which the
absence of tune times is of vital importance.
IMPORTANT SPECIFICATIONS:
- EARTH WAVE COMMUNICATIONS.
- IONOSPHERE COMMUNICATIONS.
- COMPLETE COVERAGE OF HF BAND.
- NO NEED OF ANTENNA COUPLER.
- NULL TUNE TIME.
- LOW WEIGHT.
- RESISTANCE TO WINDS HIGHER THAN 150 KM/H.
- TYPE OF ASSEMBLE TRIANGULAR.
- MAXIMUM WORKING POWER HIGHER THAN 1KW.
- EARTH PLANE INDISPENSABLE.
Spanish
Production
Page 4-5
INVELCO S.A.
EQUALIZED LOAD
BALUM
AT-105-A ANTENNA TECHNICAL SPECIFICATIONS
Nominal Impedance ...................................................................... 50 Ohm.
Maximun operating power ............................................................ 1500 W.
Frequency range .......................................................................... 2 to 30Mhz.
Dimensions .................................................................................. Max. 30 m. per arm.
Weight without masts .................................................................. 8 Kg.
RF Connector ............................................................................... UHF F
Stationary wave relation ............................................................... <2.5:1 typical 1.5:1
Type of handling ........................................................................... Triangular
Power supply cable (depending on power and length) ................... RG58
RG213
Cerflex
Radiation efficiency ...................................................................... 55% in < of 4.5Mhz.
90% in > of 6 Mhz.
Wind resistance ........................................................................... 150 Km/H.
No need or use of tune units.
No mobile mechanical elements, motors, condensers, etc.
Tune time ..................................................................................... Nul.
Work ............................................................................................ Continuous at full power.
Gain from the isotropic ................................................................. >3dB.
Operating temperature .................................................................. -20ºC to + 60ºC.
Page 4-6
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
HF ANTENNA WITH
COVERAGE 2 TO 30 MHZ
(BROADBAND)
BROADBAND ANTENNA OF
PASSIVE TYPE, WITH NO
ANTENNA COUPLER
2-30 MHZ. BROADBAND ANTENNA 150W.
MODEL AT-110-A
This antenna, easy to install, is the ideal complement for fixed radiocommunication
equipments that use HF. band in discrete jumps. The absence of mobile or switching tune
elements guarantee that the tune time under a frequency change is null, therefore assures
that this antenna is the best solution for systems of scanner or A.L.E. type in which the
absence of tune times is of vital importance.
IMPORTANT SPECIFICATIONS :
- COMPLETE COVERAGE OF THE HF BAND.
- NO NEED OF ANTENNA COUPLER.
- NULL TUNE TIME.
- LOW WEIGHT.
- RESISTANCE TO WINDS HIGHER THAN 150 KM/H.
- THREE TYPES OF HANDLING ACCORDING TO THE NEEDS.
- MAXIMUM OPERATING POWER HIGHER THAN 100W.
Spanish
Production
Page 4-3
INVELCO S.A.
TECHNICAL SPECIFICATION OF THE AT-110-A ANTENNA
Nominal impedance ...................................................................... 50 Ohms.
Operating power ........................................................................... 150 W.
Frequency range .......................................................................... 2 to 30Mhz.
Dimensions .................................................................................. Max. 30 m. per arm.
Weight with no mastils ................................................................. 6 Kg.
RF Connector ............................................................................... SO239
Stationary wave relation ............................................................... <2.5:1 typical 1.5:1
Type of handling ........................................................................... Horizontal.
Vertical
In "L"
Power supply cable (depending on power and length) ................... RG58
RG213
Cerflex
Radiation efficiency ...................................................................... 60% in < of 4,5Mhz.
95% in > of 6 Mhz.
Wind resistance ........................................................................... 150 Km/H.
No need or use of tune units.
No mobile mechanical and electrical elements, motores, condensadores, etc.
Tune time ..................................................................................... No need.
Operation ..................................................................................... Continuous at full power.
Gain from isotropic ....................................................................... >2dB.
Operating temperature .................................................................. -20ºC. to + 60ºC.
Page 4-4
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
HF ANTENNA
COVERAGE 2 TO 30 MHZ
(BROADBAND)
BROADBAND ANTENNA,
PASSIVE TYPE, WITH NO
ANTENNA COUPLER
2-30 MHZ. BROADBAND ANTENNA 1500W.
AT-110-C
This antenna, easy to install, is the ideal complement for fixed radiocommunication
equipment that use HF. band in discrete jumps. The absence of mobile or switching tune
elements guarantee that the tune time before a frequency change is null, therefore assures
that this antenna is the best solution for systems of scanner or A.L.E. type in which the
absence of tune times is of vital importance.
IMPORTANT SPECIFICATIONS:
- IONOSPHERE COMMUNICATIONS.
- COMPLETE COVERAGE OF HF BAND.
- NO NEED OF ANTENNA COUPLER.
- NULL TUNE TIME.
- LOW WEIGHT.
- RESISTANCE TO WINDS HIGHER THAN 150 KM/H.
- THREE TYPES OF ASSEMBLE ACCORDING TO NEEDS.
- MAXIMUM WORKING POWER HIGHER THAN 1KW.
Spanish
Production
Page 4-5
INVELCO S.A.
AT-110-C ANTENNA TECHNICAL SPECIFICATIONS
Nominal Impedance ...................................................................... 50 Ohm.
Operating power ........................................................................... 1500 W.
Frequency range .......................................................................... 2 to 30Mhz.
Dimensions .................................................................................. Max. 30 m. per arm.
Weight without masts .................................................................. 8 Kg.
RF Connector ............................................................................... UHF F
Stationary wave relation ............................................................... <2.5:1 typical 1.5:1
Type of handling ........................................................................... Horizontal.
Vertical
In "L"
Power supply cable (depending on power and length) ................... RG58
RG213
Cerflex
Radiation efficiency ...................................................................... 60% in < of 4.5Mhz.
95% in > of 6 Mhz.
Wind resistance ........................................................................... 150 Km/H.
No need or use of tune units.
No mobile mechanical elements, motors, condensers, etc.
Tune time ..................................................................................... No need.
Work ............................................................................................ Continuous at full power.
Gain from the isotropic ................................................................. >2dB.
Operating temperature .................................................................. -20ºC to + 60ºC.
EQUALIZED LOAD
BALUM
Page 4-6
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
OMNIDIRECTIONAL
WHIP ANTENNA
OMNIDIRECTIONAL WHIP ANTENNA
AT-110-V
Vertical antenna for use in mobile transceivers. This vertical antenna with omnidirectional
radiation diagram is used in mobile transceivers, with automatic or manual tuning units.
MAIN CHARACTERISTICS :
- MILITAR ANTENNA FOR HF.
- 500W PEP MAXIMUM POWER.
- REF NATO 5985-14-041-8781.
- NOMENC. AN357 (SEFT PRESCRIPTIONS)
- THREADED TYPE CONNECTOR.
- NATO GREEN COLOUR.
- 5M COMPLETE LENGTH.
- (5 CONNECTABLE ELEMENTS).
Spanish
Production
- 0.97 KG WEIGHT.
Page 4-7
INVELCO S.A.
Page 4-8
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
1.6MHz - 30MHz ANTENNA (74')
MOD: AT-111-A
Self-suporting vertical antenna of 74 pies
(22.7 metros).
Typical applications:
- Maritime coast stations.
- Air traffic.
- H.F. communications in general of
1.6 to 30 MHz.
The antenna model AT-111-A is made of fiberglass and
installed self-supported with no struts, obtaining high
performances in wind resistance and adverse
climatological conditions.
This antenna is designed for communication applications
in the range from 1.6 to 30 MHz, for its use in maritime
coast stations, aviation communications aswell as all type
of communications in telegraphy, telephone, etc. in the
range of the H.F.
A complete radiant system of great efficiency can be
formed when combined with the AC-160-A/F antenna
coupler.
The antenna must be executed in its installation with a
good ground to obtain better efficiency.
The antenna supports itself by twelve stainless steel studs
fited in a concrete base or other anchorage capable of
supporting the weight of the antenna (135 Kg.) and the
weight originated by the wind on the antenna.
Spanish
Produtcion
Page 4-11
INVELCO S.A.
TECHNICAL SPECIFICATIONS
CHARACTERISTICS :
ESFERA
- High efficiency.
- Internal reforced radiant system.
- Made of fiberglass.
- Very low cost of installation.
- Very low cost of maintenance.
AGUJEROS DE MONTAJE
1.79 CM DE DIAMETRO
12 PUNTOS PARA TORNILLOS EN
36.56 CM DE DIAMETRO
4ª SECCION
ELECTRIC
CHARACTERISTICS
Frequency range
1,6 MHz to 30 MHz
Power
1.5 KW from 1.6 to 5 MHz
3ª SECCION
5KW from 5 to 30 MHz
Insulation voltage
25 KV
Wind resistance
At 240 Km/Hour
Ice test
1,87 cm. Ice at
160 Km/Hour
Erosion resistance
Good
Centre of gravity
At 7,6 Metres
2ª SECCION
MECHANICAL
CHARACTERISTICS
Operating temperature
Length
Finish
74' (22.7metres)
Epoxy paint
Material
Weight
Fiberglass
Completion
In sphere
1ª SECCION
Page 4-12
Internal Material
Treated bronce
-50ºC to +65’C
135 Kg
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
1.6MHz - 30MHz ANTENNA (54.3')
MOD: AT-111-H (AS-5088/FRC)
Self-suporting vertical antenna of 54.3 foot
(16.6 metros).
Typical applications:
- Maritime coast stations.
- Air traffic.
- H.F. communications in general of
1.6 to 30 MHz.
The antenna model AT-111-H is made of fiberglass and
installed self-supported with no struts, obtaining high
performances in wind resistance and adverse
climatological conditions.
This antenna is designed for communication applications
in the range from 1.6 to 30 MHz, for its use in maritime
coast stations, aviation communications aswell as all type
of communications in telegraphy, telephone, etc. in the
range of the H.F.
The antenna must be executed in its installation with a
good ground to obtain better efficiency.
The antenna supports itself by twelve stainless steel studs
fited in a concrete base or other anchorage capable of
supporting the weight of the antenna (114 Kg.) and the
weight originated by the wind on the antenna.
Spanish
Production
Page 4-13
INVELCO S.A.
TECHNICAL SPECIFICATIONS
CHARACTERISTICS :
- High efficiency.
- Internal reforced radiant system.
- Made of fiberglass.
- Very low cost of installation.
- Very low cost of maintenance.
ELECTRIC
CHARACTERISTICS
Wind resistance
Frequency range
Ice test
1.6 MHz to 30 MHz
At 240 Km/Hour
Power
1.87cm. Ice at
160 Km/Hour
1Kw (AWG)
Erosion resistance
Insulation voltage
Good
25 KV
Operating temperature
-50ºC to +65’C
MECHANICAL
CHARACTERISTICS
Length
54.3' (16.6metres)
Material
Fiberglass
Internal Material
Treated bronce
Page 4-14
Finish
Epoxy paint
Weight
114 Kg
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
1.5 - 30MHz FREQUENCY RANGE
TRANSMISSION
MEASUREMENTS ACCORDING TO THE
WORKING FREQUENCY, OPTIMUN FOR
WORKING AT DISTANCES LOWER THAN
700Km.
INVERTED PANEL ANTENNA
AT-200-A
Inverted Panel Antenna, optimun for comunications in distances lower than
700Km., with gain of 6dB. opposite to an isotropic antenna and 4dB. opposite
to dipole.
Optimun output angle for incidence with Ionosphere higher than 30º.
IMPORTANT SPECIFICATIONS:
- HORIZONTAL POLARIZATION.
- GAIN HIGHER THAN 4dB. ON DIPOLE.
- HIGH TRANSMISSION ANGLE.
- ABSENCE OF NULES IN ITS RADIATION DIAGRAM OVER 30º.
- SWR. LOWER THAN 1.5
- 1.5KW TRANSMISSION POWER.
Fabricación
Española
Page 4-31
INVELCO S.A.
INVERTED PANEL ANTENNA TECHNICAL CARACTERISTICS.
MODEL AT-200-A
AT-200-A ANTENNA TECHNICAL SPECIFICATIONS
ELECTRICAL SPECIFICATIONS.
Type of antenna ........................................................................... Inverted pannel.
Working power ............................................................................. 1500 W.
Nominal impedance ...................................................................... 50 ohms.
S.W.R. ......................................................................................... <1.5
Polarization .................................................................................. Horizontal.
Radiation ...................................................................................... With high output angle.
SPECIFICATIONS.
Frequency range .......................................................................... 1.5 to 30 MHz.
Gain ............................................................................................. 6dB. (isotropic), 4dB. (dipole).
Bandwidth .................................................................................... >250 KHz.
Load to wind ................................................................................. Better of 150Km/h.
Length .......................................................................................... According frequency.
Weight ......................................................................................... 10 Kg. (With Balum)
Tighten ........................................................................................ 4 towerds piered.
Rf Connector ................................................................................ Type "N" or "PL259" (select)
Coaxial wire ................................................................................. According to distance and
frequency.
Working measurements Fr = 2.830KHz.
Length of each side of the panel = 26.50mts.
Towers height, minimun 15mts.
Page 4-32
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
1.6MHz - 30MHz ANTENNA (35')
MOD: AT-353-A (V-353)
Self-suporting vertical antenna of 35 pies
(10.7 metros). Optimum for ships by his low
weight.
Typical applications:
- Maritime coast stations.
- Ships.
- H.F. communications in general of
1.6 to 30 MHz.
The antenna model AT-353-A is made of fiberglass and
installed self-supported with no struts, obtaining high
performances in wind resistance and adverse
climatological conditions.
This antenna is designed for communication applications
in the range from 1.6 to 30 MHz, for its use in maritime
coast stations, aviation communications aswell as all type
of communications in telegraphy, telephone, etc. in the
range of the H.F.
The antenna must be executed in its installation with a
good ground to obtain better efficiency.
The antenna supports itself by five stainless steel studs
fited in a concrete base or other anchorage capable of
supporting the weight of the antenna (17.7 Kg.) and the
weight originated by the wind on the antenna.
Automatic operation with tuning unit Sunair CU-9150H
Spanish
Production
Page 4-15
INVELCO S.A.
TECHNICAL SPECIFICATIONS
CHARACTERISTICS :
- High efficiency.
- Internal reforced radiant system.
- Made of fiberglass.
- Very low cost of installation.
- Very low cost of maintenance.
ELECTRIC
CHARACTERISTICS:
Frequency range
1.6 MHz to 30 MHz
Power
1Kw (AWG)
Insulation voltage
25 KV
Side support
Base mounting bracket
& backing plate
Page 4-16
MECHANICAL
CHARACTERISTICS
Length
35' (10.7metres)
Material
Fiberglass
Internal Material
Treated bronce
Wind resistance
At 161 Km/Hour
Ice test
19mm. Ice at
160 Km/Hour
Erosion resistance
Good
Operating temperature
-50ºC to +65’C
Finish
Epoxy paint
Weight
17.7 Kg
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
High gain HF
Antenna for mediun
and long large
range coverage
communications
Power handling
20Kw avg
70Kw pep
MF/HF ANTENNA
MODEL AT-505-A
CARACTERÍSTICAS TÉCNICAS :
- Frequency range ....................................... 2 - 30 Mhz. (AT-505-A)
- Power handling capability ........................ 70Kw pep.
20Kw avg.
- Polarization ................................................ Vertical.
- VSWR max. ................................................ 2,0:1 (AT-505-A)
- Input impedance ........................................ 50ohm.
- Connector .................................................. "N" Type
- Wind resistance (without ice) ................... 225Km/h.
- Compact structure.
Page 4-17
INVELCO S.A.
TECHNICAL SPECIFICATIONS
SPECIFICATIONS:
- Polarization ............................................. Vertical.
- Azimutal plane pattern .......................... Circular within 0.5dB at
10º elevation.
- VSWR max. ............................................. 2.0:1 (505);
2.0:1 (506) max.
- Power handling capability ...................... 20Kw (Avg);
70Kw (PEP)
- Bandwidth ................................................ up to 15:1 (505)
up to 7:1 (506)
- Wind resistance (without ice) ................ up to 225Km/h.
- Wind resistance
(1/2" radial ice) ........................................ up to 145Km/h.
Page 4-18
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
High gain HF Antenna for
medium and long large range
coverage communications.
Power handling
10Kw avg
50Kw pep
MF/HF LOG-PER ANTENNA
MODEL AT-521-A
TECHNICAL SPECIFICATIONS:
- Frequency range ....................................... 4 - 30 Mhz.
- Power handling capability ........................ 50Kw pep.
10Kw avg.
- Polarization ................................................ Horizontal.
- Gain of principal lobe ................................ 12dB nominal
4-30MHz.
- VSWR max. ................................................ 2,0:1
- Input impedanze ........................................ 50ohms.
- Connector .................................................. "1-5/8'' Type
- Wind resistance (without ice) ................... 177Km/h.
Page 4-19
INVELCO S.A.
TECHNICAL SPECIFICATIONS
SCPECIFICATIONS:
- Polarization ............................................. Horizontal.
- Gain of principal lobe ............................ 12dB 4-30MHz.
- Front-to-Back ratio ............................... 8dB a 4MHz.
13dB mínimo
4.6 a 30MHz.
- Azimuth beamwidth ............................... 70º
- Speed of rotation .................................... 0.4 - 1 r.p.m. with
optional rotor.
- Rotation positions ................................. 1 2
- Wind (without ice) ................................. Up to 177Km/h.
- Wind with ice
(1/4" radial ice) ....................................... Up to 145Km/h.
- Rotating assembly .................................. Hydraulic.
- Weight ..................................................... 2404Kg. (521-1-N)
- Volume ..................................................... 6.10 m3 (521-1-N)
AZIMUTH AND ELEVATION PATTERNS: (gain in dBi)
Typical azimuth pattern in the plane of the first beam
from the ground.
Typical elevation pattern of the first beam in several frequencies.
Page 4-20
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
High gain HF Antenna for
medium and long large range
coverage comunications.
Power handling.
10Kw avg
50Kw pep
MF/HF LOG-PER ANTENNA
MODEL AT-548-A
TECHNICAL SPECIFICATIONS:
- Frequency range ....................................... 3 - 30 Mhz.
- Power handling capability ........................ 50Kw pep.
10Kw avg.
- Polarization ................................................ Horizontal.
- VSWR max. ................................................ 2,0:1
- Input impedance ........................................ 50ohm.
- Connector .................................................. "1-5/8'' Type
- Wind resistance (without ice) ................... 225Km/h.
Page 4-21
INVELCO S.A.
TECHNICAL SPECIFICATIONS
SPECIFICATIONS:
-
Polarization ............................................. Horizontal.
Frequency range ..................................... 3 a 30MHz.
Gain relative to isotropic ...................... 12.5dBi max.
Front-to-Back ratio ............................... 13dB minimum.
Azimuth beamwidth ............................... 60º max.
VSWR ....................................................... 2.0:1 max.
Wind resistance (without ice) ............... Up to 225Km/h.
Wind with ice
(1/2" radial ice) ....................................... Up to 145Km/h.
ELEVATION AND AZIMUTH PATTERNS: (gain in dBi)
Azimuth pattern at elevation angle of beam maximun gain
Page 4-22
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
HF Antenna for all range
communications.
Short,
medium, and long range
coverage.
Omni-directional.
Circular to within ±0.75dB
MF/HF INVERTED-CONE ANTENNA
MODEL AT-550-A
TECHNICAL SCPECIFICATIONS:
- Frequency range ....................................... 1.6 - 30Mhz
- Potencia admisible (máxima) .................... 50Kw pep.
25Kw avg.
- Polarization ................................................ Vertical.
- VSWR ......................................................... 2,0:1 (typical)
- Input impedance ........................................ 50ohms.
Page 4-23
INVELCO S.A.
TECHNICAL SPECIFICATIONS
ELEVATION PLANE PATTERNS:
Gain in dBi over perfect earth.
Page 4-24
SPECIFICATIONS:
-
Polarization ............................................. Vertical.
Azimuth radiation .................................. Circular ±0.75dB.
VSWR ....................................................... 2.0:1
Power capability ..................................... Depending on rage 25Kw
(avg) 50Kw (pep) range
of 3.8 to 32MHz.
- Tune ......................................................... No necessary.
- Enviromental .......................................... designed in accordance
with EIA specifications
RS-22C for loading of
190Km/. wind.
- Beacom possibility.
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
BUILT IN TWO DIFFERENT
MODULES.
SELECTABLE LOCAL OR
REMOTE OPERATION.
REMOTE OPERATION
THROUGH SERIAL PORT.
RF SWITCH
MODELS CA-500-A/B
IMPORTANT SPECIFICATIONS :
- SELECTABLE LOCAL OR REMOTE OPERATION.
- REMOTE OPERATION THROUGH RS-232-C PORT.
- FRONTAL INDICATORS OF THE CONMUTATION STATE.
- DESIGNED FOR OPERATING IN INTENSE RADIOFREQUENCY FIELDS.
- SWITCH OF 6 X 13.
- MAXIMUM CONMUTED POWER 1250 W BY INPUT.
- OPERATING FREQUENY FROM 0,1 TO 30 MHZ.
- POWER SUPPLY 220 VAC ±20%, 50HZ.
- OPERATION TEMPERATURE RANGE -10ºC A +60ºC.
- RELATIVE HUMIDITY 90%.
- CONTROL MODEL CA-500-A.
- SWITCH MODEL CA-500-B
Spanish
Production
Page 9-15
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE RF SWITCH
MODELS CA-500-A/B
Handling power input/output ...........................1250 W.
Operating frequency ......................................0,1 - 30Mhz.
R.O.E. .......... ................................................< 1,25
Number of RF inputs/outputs ..........................6
Number of RF outputs/inputs ..........................12
Output for artificial load ..................................1
Types of input/output connectors .....................N (female).
Switching time ...........................................<50mS.
Remote contro ...............................................RS232C.
Local Control .................................................Frontal switch.
Frontal operation selector ................................Local/Remote.
Power supply .................................................220Vac.
Consume ....... ................................................40W.
Temperature range ........................................-10ºC to +60ºC.
Relative humidity ...........................................90%.
Dimensions ..............................................Frontal of 19.
Height 6U (266mm).
Depth 450 mm.
CA-500-A Antenna switch control
Page 9-16
CA-500-B Antenna switch
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
8 ANTENNAS SWITCHING TO 8
RECEIVERS FOR RF SIGNALS
FROM 0 TO 30MHz.
REMOTE OPERATION BY
MEANS OF SERIAL PORT.
Rx ANTENNAS SWITCH
MODEL CA-800-A
This equipment allows to assign any antenna (8 antennas), to one or several receivers
simultaneously (8 receivers).
IMPORTANT SPECIFICATIONS :
- REMOTE OPERATION BY MEANS OF RS-232-C PORT.
- SWITCHING STATE FRONTAL INDICATORS.
- DESIGNED FOR OPERATING IN INTENSE RADIOFREQUENCY FIELDS.
- SWTICHING TO 8 ANTENNAS TO 8 RECEIVERS.
- OPERATION FREQUENCY FROM 0 TO 30 MHZ.
- POWER SUPPLY 220 VAC ±10%, 50HZ.
- OPERATION TEMPERATURE RANGE -30ºC TO +85ºC.
- MAXIMUM SIGNAL LEVEL +40dB.
- IMPEDANCE 50Ω.
- MEMORAZING OF THE LAST STATE. IN CASE OF FAILURE, IT RETRIEVES THE
STATE IT WHICH IT GOT DISCONNECTED.
Spanish
Production
Page 9-25
INVELCO S.A.
Rx ANTENNS SWITCH TECHNICAL CHARACTERISTICS
MODEL CA-800-A
Number of antennas to switch .................................... 8
Number of receivers to swicth .................................... 8
Number of inputs per antenna ..................................... 8
Input/Output impedances ............................................ 50 Ω.
Type of coaxial connector ........................................... BNC Female.
Maximum level signal .................................................. +40dBm.
Insertion loss (an antenna to an Rx) ........................... -0.2dB.
Signals broadband ........................................................ 0 to 30Mhz.
Type of switching ........................................................ per relays.
Memorization of last state (when connecting it, retrieves state in which it
disconnected).
Control by means of PC
RS-232-C control bus
Frontal signaling of switching
Power supply voltage .................................................. 220VAC ±10%
Power used .................................................................. 10VA.
Power supply fuse ....................................................... 2Amp.
Operation temperature range ...................................... -30ºC +85ºC
Mechanicals:
Width: ................................................................ 482.50mm. (19'')
Height: ............................................................... 177.50mm. (4U)
Depth: ................................................................ 320.00mm.
Weight: ............................................................... 7Kg.
Page 9-26
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
BUILT IN TWO DIFFERENT
MODULES.
REMOTE OPERATION
THROUGH SERIAL PORT.
RF SWITCH
MODELS CL-525-A/CA-525-A
IMPORTANT SPECIFICATIONS :
- REMOTE OPERATION THROUGH RS-232-C PORT.
- FRONTAL INDICATORS OF THE SWITCH STATE.
- DESIGNED FOR OPERATING IN INTENSE RADIOFREQUENCY FIELDS.
- SWITCH OF 12 X 13, B/W.
- MAXIMUM SWITCH POWER 1250 W.
- OPERATING FREQUENY FROM 0,1 TO 30 MHZ.
- POWER SUPPLY 220 VAC ±20%, 50HZ.
- OPERATION TEMPERATURE RANGE -10ºC A +60ºC.
- RELATIVE HUMIDITY 90%.
- CONTROL MODEL CL-525-A.
- SWITCH MODEL CA-525-A
Spanish
Production
Page 9-17
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE RF SWITCH
MODELS CL-525-A/CA-525-A
Handling power input/output .............................. 1250 W.
Operating frequency .......................................... 0,1 - 30Mhz.
SWR
1.6 to 20MHz ................................. ≤ 1,25 ±0.15
20 to 30MHz .................................. ≤1.50 ±0.15
Number of RF inputs/outputs ............................. 12
Number of RF outputs/inputs ............................. 12
Output for artificial load ..................................... 1
Types of input/output connectors ....................... N (female).
Switching time ................................................... <50mS.
Remote control .................................................. RS232C.
Power supply ..................................................... 220VAC.
Consume ............................................................ 40W.
Temperature range ............................................ -10ºC to +60ºC.
Relative humidity ............................................... 90%.
Dimensions ........................................................ Frontal of 19.
Height 6U (266mm).
Depth 450 mm.
E
R
U
T
C
PI
L
A
U
CT
A
R
T
N
NO CO
CL-525-A Antenna switch control
Page 9-18
CA-525-A Antenna switch.
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
TONES DISCRIMINATOR FOR
CONTROL OF MUTES, ON/
OFF OF EQUIPMENTS AND
ALARMS.
COMMUNICATION THROUGH
TELEPHONE LINE (2 WIRES)
PTT´S / MUTES DETECTOR
MODEL DT-100-A
The tone discriminator DT-100-A, operates through a telephone line with the tone
generator GT-302-A. It allows to decode internally tones sent by the generator, carrying
out orders that cannot be sent by an ordinary remote-controller due to is retard in the
execution (mute, on and off of equipments, reset of the remote-controllers, orders, etc.).
IMPORTANT SPECIFICATIONS :
- AUDIO BAND 300HZ TO 3.000HZ .
- LINE IMPEDANCE 600 OHMS.
- LEVEL OF LINE INPUT -30DBM TO 0DBM ADJUSTABLES.
- POWER SUPLY 220 VAC, ±20%, 50/60HZ.
- TEMPERATURE RANGE -20ºC TO +60ºC.
- HUMIDITY 95%
Spanish
Fabrication
Page 7-9
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE PTT´S/MUTES DETECTOR.
MODEL DT-100-A
DT-100-A PTT'S/MUTES DETECTOR TECHNICAL
CHARACTERISTICS
Generals: The DT-100-A tone discriminator operates
through a telephone line with the GT-302-A tones
generator. It allows to decode internally tones sent
by the generator, executing orders that cannot be
sent by an ordinary remote-controller due to its retard
in the execution (PTT, telegraphy operation, on and
off of the equipments, reset of the remote-controllers,
orders, etc.).
TONES DISCRIMINATOR TECHNICAL SPECIFICATIONS
Audio Band ......................................... 300 to
3.000Hz
Line impedance ................................. 600 ohms.
Line input level ................................... -30 to0 dBm
adjustables.
Nº of audio and PTT lines .................. 6 máximum.
PTT activation ..................................... By tone of 2900Hz.
-25dBm mínimum
Line output level ................................. -30 to 10dBm
adjustables.
PTT contact ......................................... By rele
Power Supply ...................................... 220VAC ±20%
50Hz.
Operating temperature ....................... -30 to +60 ºC.
Relative Humidity ................................ 95%
Dimensions:
Width Rack ......................................... 19" Inches.
Height ................................................. 1U (44mm.)
Depth .................................................. 320mm.
Weight ................................................. 5Kg.
Page 7-10
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
RESET FOR
STATIONS
COASTAL
RESET FOR COASTAL STATIONS
MODEL DT-302-A
The DT-302-A tone discriminator is a device that allows to reset the rack that contains the
modem, remote control and C70 of the Digital Selective Call of the Global Maritime
Distress Safety System.
IMPORTANT SPECIFICATIONS :
- POWER SUPPLY -48VCC (OTHER POWER SUPPLIES ARE OPTIONAL).
- TEMPERATURE RANGE -20ºC TO +60ºC.
- HUMIDITY 95%
Spanish
Production
Page 7-21
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE RESET FOR COASTAL STATIONS
MODEL DT-302-A
TECHNICAL CHARACTERISTICS OF THE DT-302-A
TONE DISCRIMINATOR
General:
The DT-302-A tones discriminator operates through
a connection with the power supplies' controller that
allows, by means of a remote command, to make a
complete reset of the rack. It is done by the cut of the
-48Vcc power supply timer.
TECHNICAL SPECIFICATIONS OF THE TONES
DISCRIMINATOR
Reset shot .......................................... Through command
Reset contact ...................................... Through relay
Power supply ...................................... -48VCC (other power
supplies
are
optional)
Operating temperature ....................... -20 to +60 ºC.
Relative humidity ................................ 95%
MEASUREMENTS:
Rack width .......................................... 19" Inches
Height ................................................. 1U (44mm.)
Depth .................................................. 320mm.
Weight ................................................. 5Kg.
Page 7-22
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
MF/HF TRANSMITTER POWER 500 W.
LOCAL/REMOTE CONTROL PC WITH BUS RS-232-C
SPANISH DESIGN AND PRODUCTION.
MF/HF 500W TRANSMITTER
MODEL EM-505-D
Completely solid state. As it is made with modular technique, it is easier to repair.
Broadband technology in a coverage from 1.6 to 30 MHz with instantaneous change of
the working frequency and a resolution of 1 Hz.
Appropriate for military, civil and maritime communication use; either on boat or coast
station.
IMPORTANT SPECIFICATIONS :
- EXCITER DESIGN COMPLETELY DIGITAL.
- FREQUENCY RANGE FROM 1.6 TO 30 MHZ.
- OUTPUT POWER 500W.
- TELEPHONE AND DATA COMMUNICATION.
- MEMORIZES UP TO 255 CHANNELS WITH ALL THEIR PARAMETERS.
- MODULAR FABRICATION EASY TO MAINTAIN.
- LOCAL/REMOTE CONTROL VIA RS-232-C.
- ROE TOLERANCE: INFINITE.
- INDIVIDUAL TRANSMITTER SOFTWARE CONTROL TL-500-T.
- MULTIPLE TRANSMITTER SOFTWARE CONTROL SC-516-A
- AUTOMATIC OPERATION WITH TUNING UNIT SUNAIR CU-9150H
.
Page 2-5
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE EM-505-D TRANSMITTER
GENERAL SPECIFICATIONS
- Modular construction with units:
·Digital Exciter model
EX-500-A.
·Linear Amplifier model
AL-350-A.
·Power Supply
FA-312-A.
- Rated power ..................................................... 500 W.
- Designed completely in solid state.
- Posibility to operate in reduced powers.
- Remote control through bus RS232.
- Number of channels to memorize ................. 255.
- Linear phase filters for data transmission.
- Works in all modes ......................................... Telegraphy
Voice
Data
- Infinite ROE tolerance.
- Works with three-phase or single-phase current.
- Made of aluminium able to work in seacoast areas with extreme
temperatures and humidity.
- Mechanical design of small size.
- Ready for working with automatic antenna tunning unit SUNAIR
CU-9150H
ELECTRICAL SPECIFICATIONS
- Working frequency: ........................................
- Frequency resolution: .....................................
- Frequency stability: .........................................
Optional: ..........................................................
- Number of channels to memorize: ...............
1.6 - 30 MHz.
1 Hz.
0.5 ppm.
0.01 ppm.
255.
- Output power: .................................................. 500 W +/-1dB
- Power regulation: ............................................ -3 dB.
-6 dB.
-10 dB.
- Operating with only the exciter: .................. 75 W.
- Wattmeter (incident/reflected): .................... Incorporated.
- Power amplifiers: ............................................ Solid state.
- ROE tolerance: ................................................ Infinite.
- Protection against short-circuits and open-circuit of antenna.
- Radiated harmonics: ....................................... -60 dB.
- Out-of-band spurious: ..................................... -60 dB.
- Intermodulation (2 tones) ............................. Best -31dB +/-1dB
- Power amplifier made with two modules of 600 W added and
possibility of operating with only one in case of failure.
- Output impedance: .......................................... 50 ohms.
- Output connector RF: .................................... N (female).
- Broadband designed without frequency tuning.
- Operating regime: ........................................... Continuous.
- Transmission modes: ...................................... J3E, J2A, J2B,
H3E, A1A, F1B.
- Linear phase filters for data transmission.
- Frequency response: ....................................... 300 - 3000 Hz.
- Ripple band: ..................................................... +/- 0.2 dB.
- Out-of-band attenuation: ........................ -60dB, 150 Hz, 3200Hz.
- Constant group delay (FIR Filters).
- Carrier attenuation:
J3E ................................................... -50 dB.
H3E ................................................. -6 dB.
TUNE .............................................. -10 dB.
- Not desired side band attenuation: ................ -50 dB.
- ON/OFF relation (A1A, J2A): ....................... -60 dB.
- Microphone inputs ......................................... Asimetric.
- Input impedance ............................................. 600 ohms.
- Input level ........................................................ 500 mVpp max.
- Microphone level compressor ....................... 42 dB.
- Time of compressor response ....................... 1 ms.
- Minimum threshold of compressor .............. 3.90 mVpp.
- Micro. PTT input............................................Connected to ground.
Page 2-6
-
Line input .................................................. Simetric/asimetric.
Line input impedance ............................... 600 ohms.
Controlable input level ............................ 0 dBm (nominal).
Audio response .......................................... 250/4000 Hz.
Line compression ..................................... -24 dBm to +6 dBm.
Compressor response time ...................... 1 ms.
Compressor time fall ................................ 230 ms.
PTT input line .......................................... Connected to ground.
-
Data input through line (modem optional).
Data PTT through line ............................ Connected to ground.
Line compressor in data .......................... 0 dBm to +6 dBm.
Audio input level ...................................... 0 dBm.
- Keyer input ............................................... Connected to ground.
- Ways of keying ......................................... J2A, A1A.
- PTT retention when keying ................... 1 sec.
- 1000 ohms sidetone input ....................... 1 Vpp adjustable.
- Sidetone output impedance ...................... 10000 ohms.
- Programmable delay in the output of external relays and mutes
as for the PTT.
- External relays and mutes as for the PTT adjustable from 1ms to
150ms.
POWER SUPPLY SPECIFICATIONS
- Three-phased power supply voltage +/- 10%:
........................................................................
220 Vac.
380 Vac.
440 Vac.
- Single-phased power supply voltage: ... Optional.
- Network power supply frequency ........ 50/60 Hz.
- Power consumed: .................................. Stand by 400 W.
Transmission 2,2Kw.
MECHANICAL SPECIFICATIONS
- Mechanical composition:
·Digital exciter model .................... EX-500-A.
·Linear amplifier model ................. AL-350-A.
·Power supply model ................... FA-312-A.
- Type of handling ..................................... Piled up collections.
- Handled in rack of 19 inches .................. Optional.
- External dimensions:
·Width .......................................... 500mm.
·Height ......................................... 680mm.
·Depth .......................................... 700mm.
- Fabrication..............................................Anticorrosive
aluminium
- Antivibration and crash support ............. Optional.
- Total weight ............................................ 160 Kg.
ENVIRONMENTAL SPECIFICATIONS
- Operation temperature: .......................... 0 to 50ºC.
- Storage temperature: .............................. -30 to 80ºC.
- Height ...................................................... 2500 mt.
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
MF/HF TRANSMITTER POWER 1000 W.
LOCAL/REMOTE CONTROL PC WITH BUS RS-232-C
SPANISH DESIGN AND PRODUCTION.
MF/HF 1KW TRANSMITTER
MODEL EM-525-D
Completely solid state. As it is made with modular technique, it is easier to repair.
Broadband technology in a coverage from 1.6 to 30 MHz with instantaneous change of
the working frequency and a resolution of 1 Hz.
Appropriate for military, civil and maritime communication use; either on boat or coast
station.
IMPORTANT SPECIFICATIONS :
- EXCITER DESIGN COMPLETELY DIGITAL.
- FREQUENCY RANGE FROM 1.6 TO 30 MHZ.
- OUTPUT POWER 1000W.
- TELEPHONE AND DATA COMMUNICATION.
- MEMORIZES UP TO 255 CHANNELS WITH ALL THEIR PARAMETERS.
- MODULAR FABRICATION EASY TO MAINTAIN.
- LOCAL/REMOTE CONTROL VIA RS-232-C.
- ROE TOLERANCE: INFINITE.
- INDIVIDUAL TRANSMITTER SOFTWARE CONTROL TL-500-T.
- MULTIPLE TRANSMITTER SOFTWARE CONTROL SC-516-A
- AUTOMATIC OPERATION WITH TUNING UNIT SUNAIR CU-9150H
.
Page 2-7
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE EM-525-D TRANSMITTER
GENERAL SPECIFICATIONS
- Modular construction with units:
·Digital Exciter model
EX-500-A.
·Linear Amplifier model
AL-320-A.
·Power Supply
FA-312-A.
- Rated power ..................................................... 1000 W.
- Designed completely in solid state.
- Posibility to operate in reduced powers.
- Remote control through bus RS232.
- Number of channels to memorize ................. 255.
- Linear phase filters for data transmission.
- Works in all modes ......................................... Telegraphy
Voice
Data
- Infinite ROE tolerance.
- Works with three-phase or single-phase current.
- Made of aluminium able to work in seacoast areas with extreme
temperatures and humidity.
- Mechanical design of small size.
- Ready for working with automatic antenna tunning unit SUNAIR
CU-9150H
ELECTRICAL SPECIFICATIONS
- Working frequency: ........................................
- Frequency resolution: .....................................
- Frequency stability: .........................................
Optional: ..........................................................
- Number of channels to memorize: ...............
1.6 - 30 MHz.
1 Hz.
0.5 ppm.
0.01 ppm.
255.
- Output power: .................................................. 1000 W +/-1dB
- Power regulation: ............................................ -3 dB.
-6 dB.
-10 dB.
- Operating with only the exciter: .................. 75 W.
- Wattmeter (incident/reflected): .................... Incorporated.
- Power amplifiers: ............................................ Solid state.
- ROE tolerance: ................................................ Infinite.
- Protection against short-circuits and open-circuit of antenna.
- Radiated harmonics: ....................................... -60 dB.
- Out-of-band spurious: ..................................... -60 dB.
- Intermodulation (2 tones) ............................. Best -31dB +/-1dB
- Power amplifier made with two modules of 600 W added and
possibility of operating with only one in case of failure.
- Output impedance: .......................................... 50 ohms.
- Output connector RF: .................................... N (female).
- Broadband designed without frequency tuning.
- Operating regime: ........................................... Continuous.
- Transmission modes: ...................................... J3E, J2A, J2B,
H3E, A1A, F1B.
- Linear phase filters for data transmission.
- Frequency response: ....................................... 300 - 3000 Hz.
- Ripple band: ..................................................... +/- 0.2 dB.
- Out-of-band attenuation: ........................ -60dB, 150 Hz, 3200Hz.
- Constant group delay (FIR Filters).
- Carrier attenuation:
J3E ................................................... -50 dB.
H3E ................................................. -6 dB.
TUNE .............................................. -10 dB.
- Not desired side band attenuation: ................ -50 dB.
- ON/OFF relation (A1A, J2A): ....................... -60 dB.
- Microphone inputs ......................................... Asimetric.
- Input impedance ............................................. 600 ohms.
- Input level ........................................................ 500 mVpp max.
- Microphone level compressor ....................... 42 dB.
- Time of compressor response ....................... 1 ms.
- Minimum threshold of compressor .............. 3.90 mVpp.
- Micro. PTT input............................................Connected to ground.
Page 2-8
-
Line input .................................................. Simetric/asimetric.
Line input impedance ............................... 600 ohms.
Controlable input level ............................ 0 dBm (nominal).
Audio response .......................................... 250/4000 Hz.
Line compression ..................................... -24 dBm to +6 dBm.
Compressor response time ...................... 1 ms.
Compressor time fall ................................ 230 ms.
PTT input line .......................................... Connected to ground.
-
Data input through line (modem optional).
Data PTT through line ............................ Connected to ground.
Line compressor in data .......................... 0 dBm to +6 dBm.
Audio input level ...................................... 0 dBm.
- Keyer input ............................................... Connected to ground.
- Ways of keying ......................................... J2A, A1A.
- PTT retention when keying ................... 1 sec.
- 1000 ohms sidetone input ....................... 1 Vpp adjustable.
- Sidetone output impedance ...................... 10000 ohms.
- Programmable delay in the output of external relays and mutes
as for the PTT.
- External relays and mutes as for the PTT adjustable from 1ms to
150ms.
POWER SUPPLY SPECIFICATIONS
- Three-phased power supply voltage +/- 10%:
........................................................................
220 Vac.
380 Vac.
440 Vac.
- Single-phased power supply voltage: ... Optional.
- Network power supply frequency ........ 50/60 Hz.
- Power consumed: .................................. Stand by 850 W.
Transmission 4.4 Kw.
MECHANICAL SPECIFICATIONS
- Mechanical composition:
·Digital exciter model .................... EX-500-A.
·Linear amplifier model ................. AL-312-A.
·Power supply model ................... FA-312-A.
- Type of handling ..................................... Piled up collections.
- Handled in rack of 19 inches .................. Optional.
- External dimensions:
·Width .......................................... 500mm.
·Height ......................................... 680mm.
·Depth .......................................... 700mm.
- Fabrication..............................................Anticorrosive
aluminium
- Antivibration and crash support ............. Optional.
- Total weight ............................................ 160 Kg.
ENVIRONMENTAL SPECIFICATIONS
- Operation temperature: .......................... 0 to 50ºC.
- Storage temperature: .............................. -30 to 80ºC.
- Height ...................................................... 2500 mt.
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
POWER SUPPLY FOR
INVELCO TRANSCEIVERS,
TR SERIES
POWER SUPPLY
MODEL FA-424-A
The FA-424-A power supply is ready to work with INVELCO transceivers of TR series, it
allows the connection of the transceivers to 220VAC networks. the power supply has a 12VCC
permanent voltage output which switches on remotely producing voltages of 12VCC and
28VCC.
IMPORTANT SPECIFICATIONS:
- POWER SUPPLY VOLTAGE 220VAC ±10%
- WORKING FREQUENCY 50/60HZ.
- OUTPUT VOLTAGE +12VCC (PERMANENT); +12VCC; +28VCC
- OUTPUT CURRENT +12VCC 7.50A. +28VCC 13.40A.
- LED DIODE FRONTAL INDICATORS.
- PROTECTED AGAINST FUSE, TEMPERATURE AND SHORT-CIRCUIT.
- SIZE, RACK 19'' 2U.
- WEIGHT 10KG.
Spanish
Production
Page 9-29
INVELCO S.A.
Notes:
Page 9-30
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
TONES GENERATOR FOR
GENERAL RESET OF COAST
STATIONS.
ABLE TO RESET UP TO 10
COAST STATIONS.
RESET GENERATOR
MODELO GT-302-A
The Reset Generator model GT-302-A uses the same communication line that the remotecontroller modem to send a reset signal to the Coast Station. The action is frontal and is
temporized to avoid not desired errors in the operation.
It can generate up to 10 reset orders.
IMPORTANT SPECIFICATIONS :
- FREQUENCY RANGE 300 TO 3000KHZ.
- LINE IMPEDANCE 600 OHMS.
- ATTACK LINE LEVEL -30 TO 0 dBm (ADJUSTABLE).
- NUMBER OF POSSIBLE OUTPUTS 10.
- POWER SUPPLY 110/220 VAC, 47 TO 63 HZ.
- TEMPERATURE OF -20ºC TO +70ºC.
- RELATIVE HUMIDITY 95% (WITHOUT CONDENSATION).
Spanish
Production
Page 7-7
INVELCO S.A.
CARACTERÍSTICAS TÉCNICAS DEL GENERADOR DE RESET
MODELO GT-302-A
GENERAL:
SPECIFICATIONS:
- Audio band: ................................. from 300 to 3000 Hz.
The GT-302-A Reset Generator is assigned to operate with the
- Output impedance: ...................... 600 ohms.
discriminators of the TM serial Remote-controllers or with
- Output level: ............................... from -30 dBm to 0dBm
(adjustable).
the DT-302-A reset discriminators, specifically, always through
- Tone precision: ............................ ±1Hz.
the line assigned to the communications modem of the Coast
- No. of outputs: ............................ 10.
Station.
- Type of action: ............................ Frontal.
The reset order consists of a fixed tone of appropriate level and
- Action retard: .............................. 5 S. Typical.
determined duration (2,900 Hz typicaly).
POWER SUPPLY:
- Power supply: ............................. 115/220VAC 47/63
: ............................. 48Vcc(12Vcc optional).
- Operating temperature: ............... -20ºC. to +70ºC.
- Relative humidity: ....................... 95% (without condensation).
- Dimensions:
Page 7-8
Width:
Rack19"
Height:
135mm.
Depth:
500mm.
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
HF Directional antenna of high gain for
medium and long communications distance,
with possibility of orientation by remote
control.
Power
1Kw avg.
2Kw pep
LOG-PERIODIC ANTENNA
MODEL LP-603
TECHNICAL SPECIFICATIONS:
- Frequency range ....................................... 4 - 30 Mhz.
- Power handling capability ........................ 2 Kw pep.
1 Kw avg.
- Polarization ................................................ Horizontal.
- Directive gain ............................................. 12dB.
- SWR max. ................................................... 2,5:1
- Input impedance ........................................ 50ohm.
- Input connector ......................................... "N" Type
- Wind resistance ......................................... 192Km/h.
- Diverse heigths of towers in function of the needs of
communication.
Page 4-27
INVELCO S.A.
* ROTOR APA-4
- Rotor power ........................................ 1587Kg.
- Rupture capacity ................................ 18143Kg.
- Power supply ...................................... 220VAC.
- Position precision ............................... ±5%
- Operating temperature ...................... -40°C. +80°C.
- Weight ................................................. 148Kg.
* REMOTE CONTROL MOD. RC-30-C
- Remote control up to 7 system from any remote location in
the world.
- The link may be over a standard dial-up telephone line, or
dedicated lease line at 2/4 wire.
- System control; Local (panel) or Remote (RS-232-C).
- Setup control software by INVELCO by user request.
- Integration of antenna control software in the software of
transmitters/receivers management system.
Page 4-28
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
HF Directional antenna of high gain for
medium and long communications distance,
with possibility of orientation by remote control.
Ideal for sites where are demanded minimal
size and weight conditions .
LOG-PERIODIC ANTENNA
MODEL LP-1017
TECHNICAL CHARACTERISTICS :
- Frequency range ....................................... 6.2 - 30 Mhz.
- Admissible power ...................................... 2 Kw pep.
1 Kw avg.
- Polarization ................................................ Horizontal.
- Gain ............................................................ 12 db.
- SWR Maximum .......................................... 2.5:1
- Impedance ................................................. 50 Ohm.
- Input connector ......................................... Type «N».
- Vertical angle of maximum radiation........ 35º
- Boom length .............................................. 11.52 mts.
- Larger element ........................................... 15.06 mts.
- Total number of elements ......................... 17
- Weight ........................................................ 173 Kg.
- Wind resistance ......................................... 128 Km/h.
Page 4-25
INVELCO S.A.
* R-3501 ROTOR
- Rotor power ........................................ 9000 Kg.cmt.
- Rupture capacity ................................ 23000 Kg.cmt.
- Maximum vertical load ...................... 500 Kg.
- Rotation speed .................................... 1 rpm.
- Position precision ............................... ±5%.
- Mechanism .......................................... Chaingear.
- Engine power ..................................... 1/3 C.V.
- Power supply ...................................... 125/220 Vac
- Reduction ............................................ 1800:1.
- Operating temperature ...................... -40º a +70º C
- Advance/backing handling delay ..... 5 seg.
- Weigth ................................................. 148 Kg.
* DRC-1 REMOTE CONTROL
-
Page 4-26
Power supply .......................................125/220 Vac.
Operation temperature ........................-40º to +70º C
Increase in steps of .............................10º.
Precission ............................................±5%.
Control ..................................................By telephone line.
Line impedance ...................................600 Ohms.
Data transmission level .......................-10dBm.
Data reception level .............................-10 to -30 dBm
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
ANTENNA DIPLEXER
MULTICOUPLER
CONNECTION OF A
TRANSMITTER ANTENNA TO
TWO TRANSMITTERS
ANTENNA DIPLEXER
MULTICOUPLER MOD. MA-100-A
Equipment intended for permitting the operation of several transmitters in different
frequencies with an alone antenna.
Passive device without insertion losses practically and that isolates a transmitter of
another one in more than 25dB., avoiding thus the intermodulation between them.
IMPORTANT SPECIFICATIONS:
- R.O.E. IN ALL INPUTS BETTER THAN 2:1.
- INPUT POWER 1.200 W.
- NUMBER OF INPUTS 2.
- NUMBER OF OUTPUT 1.
- REJECT BETWEEN INPUTS BETTER THAN 26 DB.
- PASSIVE EQUIPMENT.
- CONTROL IS NOT NECESSARY.
- POWER SUPPLY IS NOT NECESSARY.
Spanish
fabrication
Page 5-7
INVELCO S.A.
ANTENNA DIPLEXER MULTICOUPLER TECHNICAL CHARACTERISTICS
MODEL MA-100-A
TECHNICAL SPECIFICATIONS:
Power used by input ........................................... 1200W.
Output power ....................................................... Add the input powers
Input/output impedance ...................................... 50 Ohm.
Input connectors ................................................. N Female
Output connectors ............................................... 7/16 Female
Number of inputs ................................................. 2
Number of Outputs .............................................. 1
Operating frequency TX1 ................................... 1,5 to 1,8 MHz.
Operating frecuency TX2 .................................... 2,1 to 7 MHz.
Insertion loss of an input in the output ............... Maximum 1DB (tipical 0,3 DB.)
Dimensions
Height .................................................................. 185mm
Width ................................................................... 500mm
Depth ................................................................... 500mm
Weight ................................................................. 7 Kg.
Finishing .............................................................. RAL 7001/ RAL 7031
Serigraphy ............................................................ Whait / black
Eject between inputs ............................................ Better than 26 DB.
ROE in all inputs .................................................. Better 2:1
NOTE: This equipment does not need any external
control neither power supply.
NOTE: Between operating bands must remain at
least a 20% of keeper band.
Page 5-8
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
ANTENNA
TRIPLEXER
MULTICOUPLER
CONNECTION OF A
TRANSMITTER ANTENNA TO
THREE TRANSMITTERS
ANTENNA TRIPLEXER
MULTICOUPLER MOD. MA-101-A
Equipment intended for permitting the operation of several transmitters in different
frequencies with an alone antenna.
Passive device without insertion losses practically and that isolates a transmitter of
another one in more than 25dB., avoiding thus the intermodulation between them.
IMPORTANT SPECIFICATIONS:
- R.O.E. IN ALL INPUTS BETTER THAN 2:1.
- INPUT POWER 1.200 W.
- NUMBER OF INPUTS 3.
- NUMBER OF OUTPUT 1.
- REJECT BETWEEN INPUTS BETTER THAN 26 DB.
- PASSIVE EQUIPMENT.
- CONTROL IS NOT NECESSARY.
- POWER SUPPLY IS NOT NECESSARY.
Spanish
fabrication
Page 5-9
INVELCO S.A.
ANTENNA TRIPLEXER MULTICOUPLER TECHNICAL CHARACTERISTIC
MODEL MA-101-A
TECHNICAL SPECIFICATIONS:
Power used by input ........................................... 1200W.
Output power ....................................................... Add the input powers
Input/output impedance ...................................... 50 Ohm.
Input connectors ................................................. N Female
Output connectors ............................................... 7/16 Female
Number of inputs ................................................. 3
Number of Outputs .............................................. 1
Operating frequency TX1 ................................... 1,5 to 1,8 MHz.
Operating frecuency TX2 .................................... 2,182 MHz.
Operating frecuency TX3 .................................... 2,5 to 7 MHz.
Insertion loss of an input in the output ............... Maximum 1DB (tipical 0,3 DB.)
Dimensions
Height .................................................................. 185mm
Width ................................................................... 500mm
Depth ................................................................... 500mm
Weight ................................................................. 7 Kg.
Finishing .............................................................. RAL 7001/ RAL 7031
Serigraphy ............................................................ Whait / black
Eject between inputs ............................................ Better than 26 DB.
ROE in all inputs .................................................. Better 2:1
NOTE: This equipment does not need any external
control neither power supply.
NOTE: Between operating bands must remain at
least a 20% of keeper band.
Page 5-10
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
ANTENNA CUATRIPLEXER
MULTICOUPLER
CONNECTION OF A
TRANSMITTER ANTENNA TO
FOUR TRANSMITTERS
ANTENNA CUATRIPLEXER
MULTICOUPLER MOD. MA-102-A
Equipment intended for allowing the operation of several transmitters in different
frequencies with one single antenna.
It is a passive device with practically no insertion losses, that isolates one transmitter from
another in more than 25dB., avoiding thus the intermodulation between them.
IMPORTANT SPECIFICATIONS:
- R.O.E. IN ALL INPUTS BETTER THAN 2:1.
- INPUT POWER 1.200 W.
- NUMBER OF INPUTS 4.
- NUMBER OF OUTPUT 1.
- REJECT BETWEEN INPUTS BETTER THAN 26 DB.
- PASSIVE EQUIPMENT.
- NO CONTROL NEEDED.
- NO POWER SUPPLY NEEDED.
Spanish
Production
Page 5-11
INVELCO S.A.
ANTENNA CUATRIPLEXER MULTICOUPLER TECHNICAL CHARACTERISTICS
MODEL MA-102-A
TECHNICAL SPECIFICATIONS:
Input power .......................................................... 1200W.
Output power ....................................................... Add the input powers
Input/output impedance ...................................... 50 Ohm.
Input connectors ................................................. N Female
Output connectors ............................................... 7/16 Female
Number of inputs ................................................. 4
Number of Outputs .............................................. 1
Operating frequency TX1 ................................... 1,5 to 1,8 MHz.
Operating frequency TX2 ................................... 2,182 MHz.
Operating frequency TX3 ................................... F. Tx2 > F. Tx3 < F. Tx4.
Operating frequency TX4 ................................... F. Tx3 > F. Tx4 < 30MHz.
Insertion loss of an input to the output ............... Maximum 1dB (tipical 0,3dB.)
Dimensions
Height .................................................................. 185mm
Width ................................................................... 500mm
Depth ................................................................... 500mm
Weight ................................................................. 7 Kg.
Finishing .............................................................. RAL 7001/ RAL 7031
Serigraphy ............................................................ Whait / black
Reject between inputs .......................................... Better than 26dB.
ROE in all inputs .................................................. Better 2:1
NOTE: This equipment does not need any external
control neither power supply.
NOTE: 20% of keeper band must remain at least
between operating bands.
Page 5-12
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
DATA MODEM AT HIGH
SPEED SERIAL TYPE FOR
HF. DESIGNED FOR 2400
BAUDS.
WORKS WITH NORM
STANAG 4285
HIGH SPEED DATA MODEM
MODEL MD-571-A
Data modem at high speed for HF. Designed for data communications on a radio circuit of
up to 4.800 bauds. It uses a channel of 7.200 bps with modulation of 8 phases on a tune of
1.800 Hz. A powerful data equalizer cuts off the interference produced by multiple routes and
intersymbols. It uses convolutions correction codes (FEC), interleaving and Viterbl. Decoding
is determined by software, speeds between 75 and 2.400 Bauds.
IMPORTANT SPECIFICATIONS :
- Complete Duplex and Semiduplex.
- Adaptive supression filter.
- Compatible with norm
STANAG 4285
MIL STD188-110A
- Allows 6.5ms of multiple routes.
- Allows fading of up to 25Hz.
- Autorate and autointerleaving.
- Data or preamble synchronism.
- Synchronous or Asynchronous DTE interface.
- ASCII remote control.
Page 6-3
INVELCO S.A.
DATA MODEM OF HIGH SPEED MODEL MD-571-A
Data speed (bps). ................................ Full duplex codified or halfduplex codified 75, 150, 300,
600, 1200, 2400 Halfduplex, not codified: 4800.
Interleaving retard ................................ 0, 1.2 or 9.6 seconds.
Modulation. ......................................... M-ary PSK, 2400 sim/seg.
Multi-route tolerance ............................ 5 miliseconds.
Bandwidth ........................................... (300-3400 Hz).
Doppler synchronism .......................... ±75 Hz.
Tracking by Doppler effect ................... 3.5 Hz.
Equalization. ....................................... Directed equalization of data.
Sincronising. ....................................... Synchronising on data.
FSK(FSKNS) Narrow modulation ......... Central frequency ....... 2805 Hz.
Displacement ............... ±42.5 Hz.
Data speed (bps) ................................. Fullduplex and Halfduplex 75.
Wide modulation FSK (FSKWS) ......... Central frequency ........ 2000 Hz.
Displacement ................ ±425 Hz.
Data speed (bps) ................................. Fullduplex and Halfduplex 75.
Wide alternative modulation ................. Central frequency........... 2000 Hz.
FSK (FSKA) Displacement .................. ±85 Hz
Data speed (bps) ................................. Fullduplex and Halfduplex 75, 150, 300, 600, 1200, 2400.
Variable modulation FSK (FSKV) ........ Mark/Space programmable frequency.
Range 50 - 5995 Hz, tuned in increments of 5 Hz
Data speed (bps) ................................. Fullduplex and Halfduplex 75, 150, 300 y 600.
Reception tuning ................................Central frequency ± 200 Hz, tunable in increments of 10 Hz.
Dynamic range .................................... 30 db.
Correction. .......................................... Convolutional FEC, ARQ . Viterbi. Multi-route.
Intersymbol. Autoequalization. Fading of the M signal.
Adjacent channel interference.
Types of data input .............................. ASCI. Baudot. Binary.
Operating modes ................................. Facsimile. Images. Data. TIF, BMP, TARGA files. Text.
Filtering ............................................... Adaptive with excision.
Norms ................................................. STANAG 4285 (Synchronous and Asynchronous), and
Requirements. MIL-STD-188-110A.
Page 6-4
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
THIS MP-100-1 MULTICOUPLER
CAN CONNECT UP TO 8
RECEIVERS TO ONLY ONE
ANTENNA IN THE RANGE OF
400 KHz TO 30 MHz
IT CAN INCORPORATE A
PRE-SELECTOR FILTER THAT
CAN BE ACTIVATED AT WILL,
EVEN FROM THE DISTANCE.
PRE-SELECTOR MULTICOUPLER
MODEL MP-100-A
The MP-100-A pre-selector multicoupler is destined to connect, with no losses, one
receiver antenna to eight H.F. receivers in the range of 0.4 to 30 MHz with no noticeable
interaction between them. It also has an amplifier of high intercept point of third order (low
intermodulation), for compensating the losses originated in the pre-selector input filter and
the distributor of 1 to 8 outputs.
IMPORTANT SPECIFICATIONS :
- FREQUENCY RANGE OF 400 KHZ TO 30 MHZ.
- INPUT IMPEDANCE 50 OHMS.
- OUTPUT INSULATION / BETTER OUTPUT OF 30 DB
- 2ND ORDER INTERMODULATION IP2 = 50 DBM
- 3RD ORDER INTERMODULATION IP3 = 30 DBM
- POWER SUPPLY 220 VAC, 50/60 HZ.
- RANGE TEMPERATURE -20ºC TO +55ºC.
Spanish
Production
Page 5-19
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE PRE-SELECTOR
MULTICOUPLER
MODEL MP-100-A
TECHNICAL SPECIFICATIONS
Frequency range: ................................ 400 KHz - 30 MHz
Input/Output impedance ..................... 50 Ohm.
Power supply ...................................... 115/220 Vac.
Input connectors ................................. N Female.
Maximum consume ............................ 60 w.
No. of antenna inputs ......................... 1
Dimensions:
Nº of receivers output ......................... 8
Max. Input/Output R.O.E. ..................... 2:1
Height ................................................. 88 mm (2U).
Width ................................................... 482.5 mm (19').
Depth .................................................. 305 mm (12').
Input/Input insulation .......................... Better than 30 dB.
Weight ................................................. 5 Kg.
Output/Input insulation ....................... Better than 25 dB.
Finish .................................................. RAL 7001/RAL 7031
Noise figure ........................................ 10 dB maximum.
Serigraphy .......................................... Black / White
Insertion gain ...................................... 3 dB ± 3 dB.
2nd order intermodulation ................. Ip2 = 50 dBm.
NOTE:
3rd order intermodulation .................. Ip3 = 30 dBm.
It can also include internally a Notch filter (excluded band) to
attenuate some not desired frequencies inside the band,
according to what the user requires.
Input protection ................................... 30 Vrms.
Static electricity ................................... Solid state Unloader.
Other protections ................................ Fuse for R.F.
Pre-selector specifications:
Connection/desconnection ................ Frontal key
Simultaneous receiver passbands with connected preselector ...............................................
(specified by user) .............................. 450 - 513 KHz
2.045 - 3.300 KHz
or
450 - 513 KHz
2.045 - 6.300 KHz
Simultaneous receiver passbands with disconnected preselector .....................................................400 KHz to 30 MHz
Page 5-20
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
THIS MP-116-1 MULTICOUPLER
CAN CONNECT UP TO 16
RECEIVERS TO ONLY ONE
ANTENNA IN THE RANGE OF
400 KHz TO 30 MHz
IT CAN INCORPORATE A
PRE-SELECTOR FILTER THAT
CAN BE ACTIVATED AT WILL,
EVEN FROM THE DISTANCE.
PRE-SELECTOR MULTICOUPLER
MODEL MP-116-A
The MP-116-A pre-selector multicoupler is destined to connect, with no losses, one
receiver antenna to sixteen H.F. receivers in the range of 0.4 to 30 MHz with no noticeable
interaction between them. It also has an amplifier of high intercept point of third order (low
intermodulation), for compensating the losses originated in the pre-selector input filter and
the distributor of 1 to 16 outputs.
IMPORTANT SPECIFICATIONS :
- FREQUENCY RANGE OF 400 KHZ TO 30 MHZ.
- INPUT IMPEDANCE 50 OHMS.
- OUTPUT INSULATION / BETTER OUTPUT OF 30 DB
- 2ND ORDER INTERMODULATION IP2 = 50 DBM
- 3RD ORDER INTERMODULATION IP3 = 30 DBM
- POWER SUPPLY 220 VAC, 50/60 HZ.
- RANGE TEMPERATURE -20ºC TO +55ºC.
Spanish
Production
Page 5-21
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE PRE-SELECTOR
MULTICOUPLER
MODEL MP-116-A
TECHNICAL SPECIFICATIONS
Frequency range: ................................ 400 KHz - 30 MHz
Input/Output impedance ..................... 50 Ohm.
Power supply ...................................... 115/220 Vac.
Input connectors ................................. N Female.
Maximum consume ............................ 60 w.
No. of antenna inputs ......................... 1
Dimensions:
Nº of receivers output ......................... 16
Max. Input/Output R.O.E. ..................... 2:1
Height ................................................. 88 mm (2U).
Width ................................................... 482.5 mm (19').
Depth .................................................. 305 mm (12').
Input/Input insulation .......................... Better than 30 dB.
Weight ................................................. 5 Kg.
Output/Input insulation ....................... Better than 25 dB.
Finish .................................................. RAL 7001/RAL 7031
Noise figure ........................................ 10 dB maximum.
Serigraphy .......................................... Black / White
Insertion gain ...................................... 3 dB ± 3 dB.
2nd order intermodulation ................. Ip2 = 50 dBm.
NOTE:
3rd order intermodulation .................. Ip3 = 30 dBm.
It can also include internally a Notch filter (excluded band) to
attenuate some not desired frequencies inside the band,
according to what the user requires.
Input protection ................................... 30 Vrms.
Static electricity ................................... Solid state Unloader.
Other protections ................................ Fuse for R.F.
Pre-selector specifications:
Connection/desconnection ................ Frontal key
Simultaneous receiver passbands with connected preselector ...............................................
(specified by user) .............................. 450 - 513 KHz
2.045 - 3.300 KHz
or
450 - 513 KHz
2.045 - 6.300 KHz
Simultaneous receiver passbands with disconnected preselector .....................................................400 KHz to 30 MHz
Page 5-22
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
32 X 32 AUDIO
CONMUTATION MATRIX
CONTROL BY RS-232-C
32x32 CONMUTATION MATRIX
MODEL MT-200-B
The MT-200-B audio conmutation matrix allows to conmute 32 audio inputs to 32 outputs,
completely controlled by a RS-232-C. The conmutation is done by solid state circuits, not using
mechanical elements to carry out the conmutation (relays). It has the capacity of memorization
of audio connections in 4 independent memory banks.
IMPORTANT SPECIFICATIONS:
- AUDIO CONMUTATION OF 32 INPUTS / 32 OUTPUTS.
- MEMORIZATION OF CONNECTIONS IN 4 INDEPENDENT MEMORY BANKS.
- MULTIPLE INPUTS
- DISTRIBUTION
- MULTIPLE
CAN BE ADDED TO ONE
OUTPUT.
OF ONE INPUT TO MULTIPLE
OUTPUTS.
CONMUTATION POSSIBILITIES.
- POWER SUPPLY 115/220VAC 40-60HZ.
- REMOTE CONTROL
BY
RS-232-C.
- INPUT / OUTPUT, IMPEDANCE OF 600 OHMS.
- MODULAR FABRICATION AND EASY MAINTENANCE.
Spanish
Production
Page 9-7
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE 32x32 CONMUTATION MATRIX
MODEL MT-200-B
GENERAL SPECIFICATIONS:
POWER SUPPLY:
- Inputs: ......................................... 32.
- Power supply: ............................. 110/220VAC. 40-60Hz.
- Outputs: ...................................... 32.
- Consume: ..................................... 40 Watts.
- Inputs/Outputs impedance: ........ 600 ohms.
- Type of Inputs/Outputs: ............ Transformer Balanced/Not
balanced.
- Maximum level of signal: ............. 6dBm, 4V.p.p.
- Frequency response: ................... 100-20KHz.
ENVIRONMENTAL SPECIFICATIONS :
- Operating temperature range: ..... -20ºC. to +60ºC.
- Humidity: .................................... 95%.
- Rejection between frequencies: ... 80dB.
- Input/Output gain: ...................... 0dB.
MECHANICAL SPECIFICATIONS:
- Conmutation Time: ..................... 4msg. at 19.200bps. by
RS-232-C 0.7msg. at 115.200
bps. by RS-232-C.
- Width: .......................................... Rack 19''
- Distributes one input to multiple outputs.
- Adds multiple inputs to one output.
- Conmutes among Inputs/Outputs of any type.
- Memorization in 4 independent memory banks.
- It can direct a group of Inputs/Outputs with only one command.
- Control ........................................ RS-232-C
- Modular Fabrication.
Page 9-8
- Height: ......................................... 1U.
- Depth: ......................................... 340mm.
- Weight: ........................................ 3Kg.
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
G.M.D.S.S.
MF/HF DIGITAL RECEIVER
REMOTE CONTROL
COMPLETE THROUGH
RS-232
MF/HF DIGITAL RECEIVER
MODEL RX-500-A
The digital receiver model RX-500-A is made in a modular way. It uses the most advanced
technique in digital technology and it is completely controlled by RS-232-C.
IMPORTANT SPECIFICATIONS:
- FREQUENCY RANGE 100KHZ. TO 30MHZ. (1HZ. RESOLUTION)
- MEMORIZES UP TO 255
- COMPLETE REMOTE CONTROL THROUGH RS-232-C.
- INPUT PROTECTION SIGNAL RF: 30V. E.M.F.
- SPECIAL FILTER FOR GMDSS: 1700HZ ±150HZ.
- AUTOMATIC OR MANUAL AGC.
- PROGRAMMABLE SCANNER FOR THE USER.
- RECEPTION MODES: USB, LSB, A3E, H3E, J2A, A1A, F1B.
- COMPLETELY DIGITAL.
- DEDICATED DATA OUTPUT WITH EQUALIZATED FILTER.
- RECEIVER CONTROL SOFTWARE INDIVIDUAL MODEL TL-500-R
- RECEIVER CONTROL SOFTWARE MULTIPLE MODEL SC-516-A
Spanish
Production
Page 3-3
INVELCO S.A.
TECHNICAL CHARACTERISTICS
MODEL RX-500-A
TECHNICAL SPECIFICATIONS:
Input filters:
- All-pass filter: ............................. 100KHz 30MHz
- Frequency range: ......................... 100KHz to 30MHz.
- Frequency stability: .................... 0.5ppm. from 0º to 50ºC.
- Wideband pass filter: ................... 2MHz 30MHz With
attenuation of -40dB in <
1.5MHz and >34Mhz
frequency.
- No. of channels to memorize: ...... 255
- Pre-selector filter digitally sintonized from 1.5Mhz to 30MHz.
- Parameters to memorize: ............. All of the receiver.
- Pre-selector filter selectivity: -20dB ±20KHz of the on-tune
- Frequency resolution: .................. 1Hz.
level.
- Input antenna impedance: ........... 50 ohms.
- Input signal protection: ............... 30V EMF fuse 2 Amp.
- Bandpass filter attenuation: ........ 0.2dB.
- Selectable antenna attenuator: ..... 0dB to 20dB.
- Pre-selector filter attenuation: ..... 2.5dB.
- Operation modes: ........................ USB, LSB, A3E, H3E, J2A,
A1A, F1B.
Rf Amplifier:
- Sensitivity:
-Without Amplifier: ................. 0.7μV. for 10dB S/N.
-With Amplifier: ...................... 0.4μV for 10dB S/N.
- Selectivity to 3dB:
- 6KHz ±150Hz.
- 3KHz ±150Hz.
- 2.4KHz ±200Hz.
- 1.8KHz ±200Hz.
- 0.6KHz (CW y F1B) ±200Hz.
- Filters characteristics: .................. Linear phase and constant
group retard. Ripple band
<0.25dB.
- Automatic control of the gain ...... 3μV and 0dBm is smaller than
0.25dB.
- AGC rise time: ............................ 2msg.
- AGC fall time: ............................. 8 levels (5ms. at 10s.).
- AGC manual threshold: ............... Adjustable.
- Receivers dinamic range: .............. 0.4μV to 0dBm.
- Sideband supression not desired: 80dB.
- Image frequency attenuation: ...... 100dB.
- Intermediate frequency attenuation:100dB.
- Amplifier gain: ............................. 10dB.
- Intermodulation (IP3): ................. +45
- Noise factor: ................................ 1.5dB.
Scanner characteristics:
- No. of scanner channels: .............. 255
- Selection at will of the scanner channels.
- Independant time selection of continuance in channel for each
one.
- Selectable continuance time.
- Selection of:
-Not included channel in Scan.
-No detection of Scanner.
-Scan stop with own Squelch.
-Scan stop with external device.
- Scan group definition.
Control:
- Receiver control: .......................... Bus RS-232-C.
- Port speed: .................................. 19200/115200bps.
- Control parameters: ..................... All.
- Intermodulation (IP3): ................. +38
POWER SUPPLY:
- Squelch: ....................................... with adjustable threshold.
- Power supply: ............................. 110/220VAC ±10% 50-60Hz.
- Audio output
- Consume: ..................................... 20W.
-Balanced line 600ohms.: ......... 0dBm to +4dBm.
- Operating temperature: ............... -20ºC to +50ºC.
-Line output level: ................... Adjustable.
MECHANICAL SPECIFICATIONS:
-Speaker audio output 8ohm.: . 0 to 4Watts
-Speaker output lecvel: ............ Adjustable
-Headphones output (z≥8Ω): . Adjustable.
- Width: .......................................... 19'' Rack.
- Height: ......................................... 1U (44mm.).
- Depth: ......................................... 350mm.
- Weight: ........................................ 7.5Kg.
Page 3-4
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
MF/HF COMMUNICATIONS SERVER
SOFTWARE (SC-516-A)
The MF/HF Communication System is basically formed by a Server where a software
application is executed. This application manages and controls the different independent units;
RX-300-A/RX-500-A Digital HF Receivers, EM-512 Digital HF Transmitters, CA-500-A Antenna
Switch Matrices, MT-200-B Audio Switch Matrices, IT-200-A Telephone Integrated units, etc.
It is also formed by one or several Clients Operation Positions where the radiocommunication
operations take place. This operations take place through a software application.
The Server handles each of the System units by means of an RX-232C Serial Port conection.
When you want to stablish a communication with the units located in remote positions, it will be
necessary to use Modems, Data Lines, etc. that allow the exchange of RS-232C between the
Server and the corresponding units. On the other hand, the Operation Positions, communicate
with the Server through a Local Ethernet Network.
An example with different possibilities of units interconnection is shown in the diagram of figure
1.
The Server provides the Operation Positions the possibility of creating MF/HF Transceivers
groups formed by a MF/HF Receiver unit and a MF/HF Transmitter unit, both independent, to
make different radiocommunication operations with such group.
Furthermore, the Server can keep MF/HF groups or units to be used in other services or systems
anothers than the MF/HF Communication System itself (for example, G.M.D.S.S., Navtex,
RadioTelex, etc.).
Spanish
Production
Page 10-5
INVELCO S.A.
MF/HF OPERATION POSITION PROGRAM
Figure 1.
Page 10-6
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
TRANSMITTERS AND
RECEIVERS CONTROL
INTEGRATION WITH
TELEFÓNICA NETWORK
MF/HF OPERATION POSITION
SOFTWARE (SW-MFHF-C)
The operation position is part of a communications system run by a server that is in charge of
controlling the different equipment that form the system. The link between the server and the
operation location is made through the Ethernet network. The program can control up to a
maximum of 8 HF groups, formed by a receiver, a transmitter and 4 telephone lines.
The task of the positions is to integrate by telephone a radio equipment, formed by a transmitter
and a HF receiver, and an RTC line. It can also take part in such integration in any direction.
At the same time, it allows communications only with one line, with one ship only or with both
at the same time.
Due to its dynamism there can be, simultaneously, up to a maximum of 4 telephone integrations
between the subscriber and the ship, and talk at the same time through different equipment.
It has an independent time counter per line in the telephone integrations for its later rating. The
counter has an automatic stop.
It allows to make a multibroadcast or multiple broadcasts for those equipment in which the
microphone is activated.
It allows the supervision of dedicated equipment as the G.M.D.S.S., Navtex, Radiotelex, etc.
It also has an alarm system to tell the opeator when told so. (Case of navigators warning).
Distribution of the receivers monitoring in several speakers.
Spanish
Production
Page 10-7
INVELCO S.A.
MF/HF OPERATION POSITION PROGRAM
It also has file registers of the operations and integrations performed.
Communications with simplex and duplex equipment can be done.
It is possible to connect with the server as much positions as allowed from the server.
It allows to send messages between the different operation positions.
The control of the receiver and transmitter equipment is nearly total from its presentation panel.
The antenna can be controlled from each transmitter and receiver.
REQUIREMENTS:
- PC Pentium III or higher, CD-ROM reader, keyboard and mouse.
-128 Mb RAM (Recommended)
- 2000/NT 4.0(SP5)/XP Windows Operative System
- 1280 x 1024 Screen definition
- Ethernet network card
- RS-232-C (PTT with pedal) communications port
Page 10-8
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
VHF COMMUNICATIONS SERVER
SOFTWARE (SW-VHF-S)
The VHF Communications System is basically formed by a Server where a software application
is executed. This application manages and controls the different independent units; TR-450-A
VHF Duplex Transceivers, TR-350-A VHF Simplex Transceivers, MT-200-B Audio Switch
Matrices, IT-200-A Telephone Integrated units, etc. It is also formed by one or several Clients
Operation Positions where the radiocommunication operations take place. This operations
take place through a software application.
The Server handles each of the System units by means of an RX-232C Serial Port connection.
When you want to stablish a communication with the units located in remote positions, it will be
necessary to use Modems or Radiolinks that allow the exchange of RS-323C between the
Server and the corresponding units. On the other hand, the Operation Positions, communicate
with the Server through a Local Ethernet Network.
An example with different possibilities of units interconnection is shown in the diagram of figure
1.
The Server provides the Operation Positions the possibility of assigning VHF Transceiver units
(Simplex and Duplex) to make different radiocommunication operations with such units.
Furthermore, the Server can keep VHF units to be used in other services or systems anothers
than the VHF Communication System itself (for example, G.M.D.S.S.).
Spanish
Production
Page 10-9
INVELCO S.A.
VHF COMMUNICATIONS SERVER PROGRAM
Figure 1
Page 10-10
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
CONTROL OF 1 TRANSMITTER
AND 1 RECEIVER AND
ACCESORIES EQUIPMENTS
FROM A DISTANCE.
RS-232-C CONTROL BUS
THROUGH TELEPHONE LINE
MODEM.
MANAGING AND CONTROL OF
TRASMITTERS AND RECEIVERS
MODEL TL-500-A
The managing and control of several Transmitter and Receiver Units is done through a
software program executed in a PC. This program offers the possibility, through its configuration,
of governing at the same time 1 independent Transmitter unit and 1 independent Receiver unit.
It shows different screens with the states and controls necessaries for the complete governing
of such units.
IMPORTANT SPECIFICATIONS :
- Can configurate 1 Transmitter and 1 Receiver independently.
- Memorizes up to 255 channels per each Transmitter.
- Memorizes up to 255 channels per each Receiver.
- Indicators of State, Frequency, Channel and Communications.
- Independent events register.
- Complete control of all the Transmitters functions.
- Complete control of all the Receivers functions.
Spanish
Production
Page 7-17
INVELCO S.A.
MANAGING AND CONTROL OF THE TRASNMITTER AND RECEIVER UNIT
MOD.TL-500-A
DIFFERENT CONFIGURATION MODES:
Note: For any other configuration, confer the manufacturer.
SOFTWARE CHARACTERISTICS:
FOR TRANSMITTER UNIT.
FOR RECEIVER EQUIPMENT.
- State, Frequency, Operating channel and
Communications indicators.
- State, Frequency, Operating channel and
Communications indicator.
- Measurements Control: Line, Rf Exciter, Tx Incident
power, Exciter reflected power.
- Mute Control of RF, Rf Gain, Rf A.G.C. Filters, Squelch,
A.G.C. and Squelch level in µV, Tune, Mode, Audio
filter, Scan and Scan of prefered channels.
- Input Control: Microphone, Line, Data, Keyer, I/Q
Data.
- Memorizes up to 255 per equipment.
- Mode control: USB, LSB, H3E, A1A
- Events register per equipment.
- RF mute control, PTT, Tune, Rf test.
- Auxiliary functions.
- Memorizes up to 255 per equipment.
- Events register per equipement.
REQUIREMENTS.
- Auxiliary functions: Quit, Power supply, Linear
Amplifier Bypass, Amplifier reset.
- PC Pentium III or superior, CD-ROM reader, Keyboard and
mouse.
- 256Mb. RAM (recommendable).
- Operating System Windows 2000 (SP2), NT. 4.0 (SP5).
- Screen Definition 1024 x 768
- Extension System of Serial Ports for the PC, if necessary.
Page 7-18
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
CONTROL OF 1 RECEIVER IN
LOCAL/REMOTE MODE.
RS-232-C CONTROL BUS
MANAGING AND CONTROL OF ONE
RECEIVER UNIT MODEL TL-500-R
The managing and control of one Receiver Unit is done through a software program executed
in a PC. This program offers the possibility, through its configuration, to govern the one
Receiver Unit. It shows different screens with the states and controls necessaries for the
complete governing of unit.
IMPORTANT SPECIFICATIONS :
- Total Configurate and Memorize of one RX-200-A, RX-300-A, RX500-A Receiver Unit.
- Memorizes up to 255 channels.
- State, Frequency, Channel and Communications Indicators.
- Events register.
- Complete control of the all Receiver functions.
Page 7-21
INVELCO S.A.
MANAGING AND CONTROL OF THE RECEIVER UNITS.
MODEL TL-500-R
DIFFERENTCONFIGURATIONMODES.
LOCAL MODE
REMOTE MODE
Note: For any other configuration, confer the manufacturer.
SOFTWARE CHARACTERISTICS:
FOR RECEIVER EQUIPMENT.
REQUIREMENTS.
- State, Frequency, Working channel and
Communications Indicators.
- PC Pentium IV or superior, CD-ROM reader, Keyboard and
mouse.
- Rf Mute control, Rf Gain, Rf A.G.C. Filter, Squelch,
A.G.C. and Squelch level in µV, Tune, Mode,
Audio Filter, Scan and Scan of prefered channels.
- One Serial Port RS-232-C.
- Memorizes up to 255 channels.
- Events register.
- Auxiliary functions.
Page 7-22
- >256Mb. RAM (recommendable).
- Operating System:Windows 2000 (SP4), XP. (SP2).
- NET Framework 2.0
- Screen definition: 1024 x 768 (recommendable)
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
CONTROL OF 1 TRANSMITTER IN
LOCAL/REMOTE MODE.
RS-232-C CONTROL BUS
MANAGING AND CONTROL OF ONE
TRANSMITTER UNIT MODEL TL-500-T
The managing and control of several Transmitter is done through a software program executed
in a PC. This program offers the possibility, through its configuration, to govern one transmitter
unit in local/remote mode. It shows different screens with the states and controls necessaries
for the complete governing of them.
IMPORTANT SPECIFICATIONS :
- Configurate EM-525-D / EM-525-X Transmitter.
- Memorizes up to 255 channels.
- State, Frequency. Channel and Communications indicators.
- Events register.
- Complete control of all the Transmitter functions.
Page 7-19
INVELCO S.A.
MANAGING AND CONTROL OF ONE TRANSMITTER UNIT.
MODEL TL-500-T
DIFFERENT CONFIGURATION MODES:
LOCAL MODE
REMOTE MODE
Note: For any other configuration, confer the manufacturer.
SOFTWARE CHARACTERISTICS:
REQUIREMENTS.
- State, Frequency, Operating channel and
Communications Indicators.
- PC Pentium IV or superior, CD-ROM reader, Keyboard and
mouse.
- Measurements control: Line, Rf Exciter, Tx Incident
Power, Reflected Power Exciter.
- One Serial Port RS-232-C.
- Input control: Microphone, Line, Data, Keyer, I/Q
Data.
- Operating System:Windows 2000 (SP4), XP. (SP2).
- Mode control: USB, LSB, H3E, J2A, A1A, F1B.
- Mute Rf control, PTT, Tune, Rf test.
- Memorizes up to 255 channels.
- Events register.
- Auxiliary functions: Quit, Power supply, Linear
Amplifier Bypass, Amplifier Reset.
Page 7-20
- >256Mb. RAM (recommendable).
- NET Framework 2.0
- Screen definition: 1024 x 768 (recommendable)
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
ONE PORT RS-232-C TO SIX
PORTS RS-232-C.
MULTICON REMOTE-CONTROLLER
MODEL TM-100-A
Designed to control through modem from one local unit up to 6 INVELCO equipments. It
has the possibility to extend in modules of 6 units.
Aswell as the control of equipments through RS-232-C, it can send 10 orders to the remote
station or receive 10 alarms from that station.
IMPORTANT SPECIFICATIONS:
Spanish
Production
- IT ALLOWS THE COTROL IN A REMOTE STATION FROM A RS-232 PORT
TO 6 RS-232 PORTS (1-6).
- SPEED CONTROL PORT TO LINE MODEM 115.200 BAUDS.
- SPEED OF THE 6 COMMUNICATION PORTS WITH OTHER DEVICES 19.200
BAUDS.
- FIFO WRITING AND READING MEMORY, INDEPENDENT IN EACH PORT
(1 - 6).
- STATES VISUALIZATION.
- POWER SUPPLY 220 VAC ±20%, 50HZ. AND -48VCC.
- TEMPERATURE RANGE -20ºC TO +70ºC.
- RELATIVE HUMIDITY 95%
Page 7-3
INVELCO S.A.
MULTICON REMOTE-CONTROLLER TECHNICAL CHARACTERISTICS
MODEL TM-100-A
It allows the INVELCO equipments control in a Remote Station from a RS232 Port to 6 RS-232 Port (1-6).
Speed of the control port to line modem 115.200 bauds.
Speed of the 6 communications ports with other devices 19.200 bauds.
Independent FIFO reading-writing memory in each port (1 - 6).
Remote control: ................. 10 I/O orders.
Orders output: ................... open collector.
Output capacity ................. 0 to 30Vcc
.......................................... Icc= 1A.
Orders output through relay:Optional.
Sent from remote: .............
Alarm signal input: ............
..........................................
Ways of sending alarms: ...
10 I/O alarms.
0 to 2.5Vcc (TTL).
0 to 25Vcc.
automatic.
interrogating.
automatic/interrogating.
with repetition.
Common RS-232 port connector.
RS-232 output ports connectors.
Modular fabrication chassis of 19'' 2U.
Power supply .......-48Vcc.
220Vac.
Consume ................... 10W
Temperature range:-20ºC to +70ºC.
Relative humidity: ...... 95%
Page 7-4
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
PERMITS TO CONTROL
UNTIL 6 EQUIPMENT (via
RS-232-C) WITH A PORT
RS-232-C
MULTICON TELECONTROL
MODEL TM-100-B
Designed to control through modem from one local unit up to 6 INVELCO equipments.
As well as the control of equipments through RS-232-C, it can send 48 orders to the
remote station or receive 48 alarms from that station.
IMPORTANT SPECIFICATIONS:
Spanish
fabrication
- IT ALLOWS THE COTROL IN A REMOTE STATION FROM A RS-232 PORT
TO 6 RS-232 PORTS (1-6).
- SPEED CONTROL PORT TO LINE MODEM 115.200 BAUDS.
- SPEED OF THE 6 COMMUNICATION PORTS WITH OTHER DEVICES 19.200
BAUDS.
- FIFO WRITING AND READING MEMORY, INDEPENDENT IN EACH PORT
(1 - 6).
- STATES VISUALIZATION.
- POWER SUPPLY 220 VAC ±20%, 50HZ. AND -48VCC.
- TEMPERATURE RANGE -20ºC TO +70ºC.
- RELATIVE HUMIDITY 95%
Page 7-5
INVELCO S.A.
TECHNICAL CHARACTERISTICS
MODEL TM-100-B
Output ports ................................................... 6 RS-232-C ( 19.200 bauds).
Remote input .................................................. Line 2/4 wire
Comunication ................................................. by standard modem.
Hardware I/O ................................................ Up to 48.
Hardware output type .................................... Open colector.
Output range .................................................. Up to 30V/1A. max.
Output by relay .............................................. Optional.
Hardware input type ...................................... High impedance.
Input range ..................................................... Up to 25V.
Power supply ................................................. 220Vac 47-63Hz.
48Vdc.
Power consumption ....................................... 10W. typ.
Operating temperature range ........................ 0ºC to +60ºC.
Relative humidity ........................................... 95% (non condensing).
Non operating temperature ............................ -20ºC to +70ºC.
Tropicalized ................................................... Yes.
Wide .............................................................. 19''Rack.
High ............................................................... 2U.
Deep .............................................................. 340mm.
Weight ........................................................... 3.2Kg.
Page 7-6
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
DIGITAL DESIGN
VMOS. AMPLIFIER
RS-232-C CONTROL
1000W. RMS POWER
MODULAR DESIGN
LOCAL / REMOTE OPERATION
THROUGH PC.
500W H.F. DIGITAL TRANSCEIVER
MODEL TR-505-D
The TR-505-D Transceiver is the only equipment in the world in which its receiver is
completely digital from its RF input. The transmitter is completely digital from the audio
input signal up to the RF amplifier.
IMPORTANT SPECIFICATIONS:
*
-
Spanish
Production
FREQUENCIES RANGE 1.6 - 30MHZ.
RESOLUTION 1HZ.
STABILITY 1PPM.
MEMORIZES UP TO 255.
MEMORIZES ALL THE PARAMETERS.
J3E (BLS, BLI), A1A, J2A, F1B, H3E MODES.
3KHZ, 1.8KHZ FILTERS, G.M.D.S.S.
LOCAL/REMOTE OPERATION THROUGH RS232.
MONITORING OF INCIDENT POWER, REFLECTED POWER AND LINE MEASURE.
OPTIONS:
A.L.E.: AUTOMATIC SEARCH OF THE BEST COMMUNICATION CHANNEL, ACCORDING
TO STANAG 4538 MIL-STD 188-141B APENDIX A.
- HIGH SPEED DATA MODEM: 9.600 BPS. IN H.F. FOR SENDING TEXTS, FAX,
IMAGES.
Page 1-5
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE 500W H.F. DIGITAL TRANSCEIVER
MODEL TR-505-D
TRANSMISSION:
POWER SUPPLY SPECIFICATIONS:
- Output power: ..................... 500W. R.M.S. ±1dB.
- Three-phased power supply voltages ±10%.:220Vac.
- Power Reduction: ................. -3dB; -6dB; -10dB.
380Vac.
- Incident and Reflected Power measurement.
440Vac.
- Micro; Line; Data; Manipulator.
- Monophased power suplly voltages: Optional.
- Tunning power for antenna automatic coupler.
- Power supply frequency:..............50/60Hz.
- Completely digital design (except RF power amplifier and
Power Supply).
- Power used:....................................Rest: 425W.
Transmission: 2.2Kw.
- Harmonics radiation: .............-50dBc
- Spurious radiation: ............... -60dBc
- Side band non-desired attenuation: ...........-60dB.
- Output impedance: ............... 50 Ohms.
- Antenna connector type: ...... N
- Continuous operation regime.
- Line input: ............................ 600 Ohms
- Audio response: ................... 300-3000Hz.
MECHANICAL SPECIFICATIONS:
- External measurements:
Pile-up format
Width:.....................................500mm.
Depth:.....................................600mm.
Height:.....................................720mm
Height with work surface:.......1220mm.
19" Format:
RECEPTION:
Transceiverr:........................4U. 26 Kg.
- Selectivity: ............................ 6KHz; 3KHz; 1.8KHz;
GMDSS Filter (1700hz).
Amplifier:............................6U. 58 Kg.
Power Supply:....................6U. 85 Kg.
- Design with high selectivity filter F.I.R. type.
- Built:.............................................Anticorrosion aluminium.
- A.G.C. increase time: ........... 1ms.
- Total weight:.................................159Kg.
- A.G.C. decrease time: ........... 5ms; 10ms; 50ms;
100ms; 500ms; 1s;
5s; 10s.
ENVIRONMENTAL SPECIFICATIONS:
- A.G.C. manual threshold adjustable from 1µV. up to
500µV.
- Operation temperature: ............... 0 to 50ºC.
- Environmental humidity: ............. 95%.
- Possibility of silence Rx.
- Built with adjustable Squelch.
ACCESORIES PROVIDED:
- Digital selective preselector adjusted automatically to
the reception frequency.
- Control Commands for RS232.
- Rx input selection: ................ Bypass
Digital Preselector
Pass band filters
- Operation Software for PC.
ACCESORIES NOT PROVIDED:
- Amplifier selection of +10dB. Ip=+45.
- Radiant system.
- Sensibility: ............................ 0.25ìV for 10dB sinad
- A.L.E.
- Independent outputs: .......... line and speaker.
- High speed data modem.
- Dynamic range: .................... -119dB up to 0dB.
- Control processor computer.
Page 1-6
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
DIGITAL DESIGN
VMOS. AMPLIFIER
RS-232-C CONTROL
1000W. RMS POWER
MODULAR DESIGN
LOCAL / REMOTE OPERATION
THROUGH PC.
1Kw H.F. DIGITAL TRANSCEIVER
MODEL TR-512-A
The TR-512-A Transceiver is the only equipment in the world in which its receiver is
completely digital from its RF input. The transmitter is completely digital from the audio
input signal up to the RF amplifier.
IMPORTANT SPECIFICATIONS:
*
-
Spanish
Production
FREQUENCIES RANGE 1.6 - 30MHZ.
RESOLUTION 1HZ.
STABILITY 0.5PPM.
MEMORIZES UP TO 250.
MEMORIZES ALL THE PARAMETERS.
J3E (BLS, BLI), A1A, J2A, F1B, H3E MODES.
3KHZ, 1.8KHZ FILTERS, G.M.D.S.S.
LOCAL/REMOTE OPERATION THROUGH RS232.
MONITORING OF INCIDENT POWER, REFLECTED POWER AND LINE MEASURE.
OPTIONS:
A.L.E.: AUTOMATIC SEARCH OF THE BEST COMMUNICATION CHANNEL, ACCORDING
TO STANAG 4538 MIL-STD 188-141B APENDIX A.
- HIGH SPEED DATA MODEM: 9.600 BPS. IN H.F. FOR SENDING TEXTS, FAX,
IMAGES.
Page 1-7
INVELCO S.A.
TECHNICAL CHARACTERISTICS OF THE 1000W H.F. DIGITAL TRANSCEIVER
MODEL TR-512-A
TRANSMISSIÓN:
POWER SUPPLY SPECIFICATIONS:
- Output power: ..................... 1000W. R.M.S. ±1dB.
- Three-phased power supply voltages ±10%.:220Vac.
- Power Reduction: ................. -3dB; -6dB; -10dB.
380Vac.
- Incident and Reflected Power measurement.
440Vac.
- Micro; Line; Data; Manipulator; I/Q Data input.
- Monophased power suplly voltages: Optional.
- Tunning power for antenna automatic coupler.
- Power supply frequency:..............50/60Hz.
- Completely digital design (except RF power amplifier and
Power Supply).
- Power used:....................................Rest: 850W.
Transmission: 4.4Kw.
- Harmonics radiation: .............-60dB
- Spurious radiation: ............... -60dB
- Side band non-desired attenuation: ...........-50dB.
- Output impedance: ............... 50 Ohms.
- Antenna connector type: ...... N
- Continuous operation regime.
- Line input: ............................ 600 Ohms
- Audio response: ................... 300-3000Hz.
MECHÁNICAL SPECIFICATIONS:
- External measurements:
Pile-up format
Width:.....................................500mm.
Depth:.....................................600mm.
Height:.....................................720mm
Height with work surface:.......1220mm.
19" Format:
RECEPTION:
Transceiverr:........................4U. 26 Kg.
- Selectivity: ............................ 6KHz; 3KHz; 1.8KHz;
GMDSS Filter (1700hz).
Amplifier:............................6U. 58 Kg.
Power Supply:....................6U. 85 Kg.
- Design with high selectivity filter F.I.R. type.
- Built:.............................................Anticorrosion aluminium.
- A.G.C. increase time: ........... 1ms.
- Total weight:.................................169Kg.
- A.G.C. decrease time: ........... 5ms; 10ms; 50ms;
100ms; 500ms; 1s;
5s; 10s.
ENVIRONMENTAL SPECIFICATIONS:
- A.G.C. manual threshold adjustable from 1µV. up to
500µV.
- Operation temperature: ............... 0 to 50ºC.
- Environmental humidity: ............. 95%.
- Possibility of silence Rx.
- Built with adjustable Squelch.
ACCESORIES PROVIDED:
- Digital selective preselector adjusted automatically to
the reception frequency.
- Control Commands for RS232.
- Rx input selection: ................ Bypass
Digital Preselector
Pass band filters
- Operation Software for PC.
ACCESORIES NOT PROVIDED:
- Amplifier selection of +10dB. Ip=+45.
- Radiant system.
- Sensibility: ............................ 0.25ìV for 10dB sinad
- A.L.E.
- Independent outputs: .......... line and speaker.
- High speed data modem.
- Dynamic range: .................... -119dB up to 0dB.
- Control processor computer.
Page 1-8
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
DIGITAL DESIGN
VMOS. AMPLIFIER.
CONTROL RS-232-C
POWER 100W. RMS
MODULAR DESIGN
LOCAL / REMOTE OPERATION
THROUGH PC.
100W H.F. DIGITAL TRANSCEIVER
MODEL TR-550-A
The TR-500-A transceiver is the only equipment in the world that has a completely digital
receiver from the Rf. input and the transmitter is completely digital from the audio input
signal up to the Rf. amplifier.
IMPORTANT SPECIFICATIONS :
- FREQUENCY RANGE 1.5 - 30MHZ.
Spanish
Production
- RESOLUTION 1HZ.
- STABILITY 0.5PPM.
- NUMBER OF CHANNELS TO MEMORIZE 250.
- MEMORIZING OF ALL THE PARAMETERS.
- MODES J3E (BLS, BLI), A1A, J2A, F1B.
- FILTERS 3KHZ, 1.8KHZ, G.M.D.S.S.
- LOCAL/REMOTE OPERATION THROUGH PA-400-E CONSOLE.
- 220VAC ±10% WITH POWER SUPPLY MOD: FA-424-A
- MEASURING OF INCIDENT POWER; REFLECTED POWER; LINE MEASSURE AND AUDIO
INPUT.
* OPTIONS:
- A.L.E.: AUTOMATIC SEARCH OF THE BEST COMMUNICATION CHANNEL.
- HIGH SPEED DATA MODEM 9.600BPS. IN H.F. FOR SENDING TEXTS, FAX, IMAGES.
- TRANSMISSION/RECEPTCION DATA SOFTWARE WITH ERROR CORRECTION
Page 1-3
INVELCO S.A.
AUDIO PROCESSOR
MODEL: PA-400-E
POWER SUPPLY
MODEL: FA-424-A
TECHNICAL CHARACTERISTICS OF THE 100W HF DIGITAL TRANSCEIVER
MODEL TR-550-A
TRANSMISSION:
RECEPTION:
- Output power: ..................... 100/125Wats. R.M.S.
- Selectivity: ............................ 6KHz; 3KHz; 1.8KHz;
Filter AFSK (1700hz).
- Power reduction: .................. -3dB; -6dB; -10dB.
- Meassure Incident Power.
- Micro; Line; Data; Key.
- Design with high selectivity filter F.I.R. type.
- A.G.C. rise time: .................. 1ms.
- Frontal test of the total output power.
- A.G.C. fall time: ................... 5ms; 10ms; 50ms;
100ms; 500ms; 1s;
5s; 10s.
- Completely digital design (except amplifier of Rf.
power).
- Manual adjustable A.G.C. threshold from 1µV. to
500µV.
- Tune power for automatic antenna coupler.
- Posibility to silence the Rx.
CONTROL PC (minimum requirements):
- Pentium III, 128Mb. Ram
- Hard disk free space. 50Mb.
- Build with adjustable Squelch.
- Selective digital preselector adjusted automatically to
the reception frequency.
- Screen definition 1024x768.
- Input selection of Rx: ........... Bypass
Digital Preselector
Bandpass filter
NECESSARY ACCESORIES:
- Selection of amplifier of +10dB. Ip=+45.
- Fuente de Alimentación FA-424-A
- Sensibility: ............................ 0.25ìV for 10dB sinad
- Dynamic Microphone.
- Independent outputs: .......... line and speaker.
- Control Pc. with RS-232-C Bus
- Dynamic range: .................... -119dB up to 0dB.
- Serial Port RS-232-C free.
PRINCIPAL CONTROL SCREEN
MODEL: TR-550-A
Page 1-4
A.L.E. CONFIGURATION SCREEN
MODEL: TR-550-A
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
QUICK, INTELIGENT AND
PRECISE AUTOMATIC
ANTENNA TUNING UNIT
OPERATES WITH ANY TYPE
OF TRANSMITTER
150W HF AUTOMATIC TUNING UNIT
US-101-C
This automatic tuning unit antenna allows to adapt the antenna to any type of transmitter or
transceiver in the hf band in a quick, intelligent and precise way. It has high perfomances with
a tunning memory WITHOUT REFRESH BATTERY that allows to guarantee its maintenance
during long periods of time not beeing used and failures in the power supply.
IMPORTANT SPECIFICATIONS:
- CONTROLED THROUGHT MICROPROCESSOR.
- NON VOLATILE MEMORY (500 ADDRESSES).
- RESISTANCE TO WATER AND OUTDOORS.
- FREQUENCIES RANGE OF 1,6 TO 30 MHZ.
- INPUT POWER FROM 10 TO 150 WATTS.
- TUNING TIME: 10 MSEG.
- ANTENNA TUNING FROM 2,7 TO 60 METROS.
Fabricación
Española
Page 5-3
INVELCO S.A.
AUTOMATIC ANTENNA TUNING UNIT TECHNICAL CHARACTERISTICS
MODEL -US-101-C
Resistance to detection and goniometry due to:
Frequencies range .................... 1,6 a 30 MHz.
Antenna types usable:
Short antennas 2.7 to 6m. ... 2. 5 - 30 Mhz.
Whip antennas 5 to 12m ...... 1.6 - 30 Mhz
Wire antennas 20 to 60m .... 1.6 - 30 Mhz
Tuning time:
First tuning .......................... <20seg.
Tuning made as
second time ......................... 20ms approx.
Tuning mode ............................. automatic
Power needed:
Working maximun ............... 150W.
For tuning ............................ 10W
Radiated during the tuning ... 8W
Impedance of Rf tuning .............. 50OHm.
R.O. E. after tuning:
Typical ................................. 1,5:1
Maximun ............................. 3:1
Efficiency .................................. 50 a 90%
Power supply ............................ 13,5Vcc ±20%
Consumption ............................. 2 Amp max.
Distancof radio to the unit ......... 100 m max.
Page 5-4
Low radiation power when tuning.
Tuning times of 20 ms.
Measurements:
Widht .................................. 127mm
Height .................................. 76mm
Depth .................................. 279mm
Weight ................................. 3,2Kg.
Environmentals:
Working temperature ........... -35 +70C
MIL-STD-61OC
Storage temperature ............ -40 + 90C
MIL-STD-81OC
Humidity .............................. MIL-STD-81OC
Rain fall ............................... MIL-STD-1O8E
BOARD II
Saline fog ............................ MIL-STD-81OC
Mechanical efforts (with stand SP-101-C):
Crash .................................. MIL-STD-61OC
method 516.2
Vibration .............................. MIL-STD-81OC
method 514.2
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y COMUNICACIONES
AUTOMATIC, QUICK,
INTELLIGENT AND ACCURATE
ANTENNA TUNING UNIT
OPERATES WITH ANY TYPE
OF INVELCO'S MF/HF
TRANSMITTER
1KW HF DIGITAL ANTENNA COUPLER
MODEL US-525-A (SUNAIR CU-9150H)
The US-525-A automatic tuning unit is actually the SUNAIR tuning unit Model CU-9150H. Its
software has been set up in the INVELCO's 1Kw transmitters in order to execute a complete
automatic group.
The US-525-A tuning unit uses high speed, efficient and reliable digital tuning network for
vertical antennas from 23' to 36'. It is also possible to stand configurations of long wires of
several types, from 50' to 150', when a long wire optional adapter is installed.
The microprocessor included in the coupler controls and selects internal elements of the
circuit. It has an integrated test (BITE) to verify its correct operation.
IMPORTANT SPECIFICATIONS :
- CONTROLLED BY MICROPROCESSOR.
- INTERNAL MEMORY WITH NO BATTERIES.
- WATER AND OUTDOORS RESISTANCE.
- 1.6 TO 30 MHZ FREQUENCY RANGE.
- 1000 WATTS ±1dB INPUT POWER.
- CONTINUOUS OPERATION.
- 50Ω INPUT IMPEDANCE.
- INTEGRATED TEST (BITE).
Page 5-5
INVELCO S.A.
1 Kw HF DIGITAL ANTENNA COUPLER
MODEL US-525-A (SUNAIR CU-9150H)
- Frequency range ......................................... 1,6 - 30MHz.
- Input impedance .......................................... 50Ω.
- Input connector type ................................... "N" hembra.
- WSR (after tuning) ...................................... 1,5:1 Better
- Input power ................................................. 1000W ±1dB.
- Efficiency according antenna ....................... 65% to 98%
- Operation at 1000W .................................... Continuous.
- Direct power supply from Transmitters EM-525 series.
- Control from equipment with no interface and completely automatic.
- Tuning time less than 4 secs. in tuned frequencies for a first time.
- Tuning time less than 30 msecs. in previously tuned frequencies although the unit has remained switched
off.
- Automatic memory of up to 4000 tunes.
- Internal memory with no batteries
- Exempt from false tuning as effect of intense fields of near RF.
- Tuning process control ................................ Microprocessor.
- Coupling cell setting .................................... Binary switch of L and C.
- Distance from US-525-A to transmitter ........ 250 feet available. Higher lenghts with special coaxial and
control wires.
- Operation temperature ................................ -50ºC. to +85ºC. protected from sun exposure.
- Humidity ..................................................... MIL STD 810F, Method 516.5 and 514.5.
- Measurements ............................................ Length 731.5mm.
Width 454.7mm.
Height 243.8mm.
- Weight ........................................................ 25.2Kg.
USUAL ANTENNAS
1.- Vertical of 23' 3 to 30MHz.
2.- Vertical of 35' 1,6 to 30MHz.
3.- Antenna of 50' to 150' long wire. (It is necessary to use and adapter for antennas higher than 75').
Specifications can be modified without previous notification.
Page 5-6
Annotations:
INVELCO S.A.
INVESTIGACIONES ELECTRONICAS Y
COMUNICACIONES
(INVELCO, S.A.)
Ronda de Poniente nº15
28760 Tres Cantos, Madrid, (ESPAÑA)
Phone. 34-91-803.24.44
Fax.
34-91-803.32.28
Web: www.invelco.com
e-mail: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement