SPT | SL-824T5 | Use and Care Manual | SPT SL-824T5 Use and Care Manual

LAMP INSTALLATION
When table or surface thickness is less
than 2 cm, please use the insole to
increase stability.
Add the Height-Increase
Insole when surface
thickness is less than 2cm.
Do not install lamp:
Limited surface
space for clamp
Surface that is too
thin or fragile to
support lamp
On a pole or
uneven surface
Horizontally
Your Guarantee
If this product is found to be faulty as a result of faulty materials or workmanship
within one year from date of purchase, it will be repaired free of charge.
This guarantee is subject to the following terms:
Sunpentown must be notified of the fault.
Proof of purchase must be presented to Sunpentown’s nominated representative.
The warranty will be void if the product if modified, misused or repaired by an
unauthorized person.
The warranty after repair will not be extended beyond the original one-year period.
All replacement parts will be new or reconditioned.
Parts, which are replaced, become the property of Sunpentown.
The warranty applies for the use of the product in the USA only.
SL-824T5
T-5 Fluorescent Task Lamp
What is NOT COVERED:
Warranty does not include freight charges.
Incidental or consequential damage caused by possible defects with this product.
Damage to product caused by improper power supply voltage, accident, fire,
floods or acts of nature.
Failure of product resulting from unauthorized modifications to the product.
Improper installation or failure to perform the necessary maintenance.
This GUARANTEE is in addition to your Statutory Rights
Thank you for your purchase, please read all instructions before using.Please keep this instruction
manual in a safe place for future reference.
Ver.01 DRH-R-84-12
SUNPENTOWN INTERNATIONAL INC.
14625 Clark Ave. City of Industry, CA 91745
Tel: 800-330-0388
service@sunpentown.com
www.sunpentown.com
IMPORTANT SAFEGUARDS
PARTS IDENTIFICATION
 If loose, use a screwdriver to tighten.
Fixture
When installing
make sure “click”
is heard.
Lamp Shade
Aluminum arm
Light bulb
Bottom cover
Lid
Dimmer control
Power switch
Fixture
When installing
make sure “click”
is heard.
Use a coin or flathead
screwdriver
Adjustment screw
 If loose, use a screwdriver to tighten screws
(use of other tools may cause damage)
Attention
Clamp
Do not use excessive force
when securing
height increased insole
BULB INSTALLATION / REPLACEMENT INSTRUCTIONS
Make sure lamp is powered off and unplugged from power source.
Wait until bulb is cool enough to handle. Bulb is hot immediately
after powering off.
Do not cut or shorten the power cord.
Always unplug lamp before performing bulb installation, bulb replacement or
maintenance.
Removal
1. Turn bulb 90 degrees and remove from socket .
Installation
1. Align base of bulb to notch on the socket. Turn bulb until a
“click” is heard.
Note: Handle with care, do not drop.
Do not replace anything other than the bulb.
Only replace with HO-24W bulb
SPECIFICATIONS
Model
Power Consumption
Power Supply
Dimension
Weight
Replacement Bulb
SL-824 T5
24W
120V / 60Hz
Approx. 22.4x27.56x19.67 (in)
3.17 lbs
HO-27W
IMPORTANT SAFEGUARDS
Do not operate this lamp near a water source to avoid electric shock.
Do not dismantle.
Do not use with power supply other than 120V~60Hz.
Do not operate lamp in close proximity to flammable or combustible vapors, such
as aerosol spray, or where oxygen is being administered.
Socket
Bulb
Notch
Teminal
This product may cause interference with radios, cordless telephones or devices
that use a wireless remote control, such as televisions. If interference occurs, move
the product away from the device, plug the device or lamp in a different outlet or
move the lamp out of the line of the remote control receiver.
Unplug the lamp during lightning storms or when unused for extended period of time.
All moisture should be properly wiped away and dried prior to use.
Do not touch bulb when lamp is on or shortly after powering off. May cause burns.
Dispose of bulbs per local regulations.
MAINTENANCE
Before cleaning, make sure lamp is powered off and unplugged. Allow sufficient time
for the bulb to cool down.
Periodically wipe the lamp with a soft damp cloth. Use a mild non-abrasive cleaner if
needed.
All liquid should be properly wiped away and dried prior to restoring power.
Do not use solvents or abrasive cleaners.
Download PDF