Hampton Bay | 27203 | Instructions / Assembly | Hampton Bay 27203 Instructions / Assembly

3 Light Pendant
Home Depot SKU 528-127 (UPC 718212272039)
(Olive Stone Finish)
Page 1
Thank you for purchasing this Hampton Bay interior light fixture. This
product has been manufactured with the highest standards of safety and
1. Traditional 3 Light Pendant in Olive Stone Finish.
2. Timeless Elegant Design.
3. Easy to assemble and install.
Before returning to your local Home Depot, please call our Customer
Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU (528-127 Olive Stone fixture) or UPC
(718212272039 Olive Stone fixture).
Page 2
1. Before starting installation of this fixture or removal of a previous
fixture, disconnect the power by turning off the circuit breaker or by
removing the fuse at the fuse box.
3. If you have any non-electrical questions about this fixture, please
contact our Customer Service Team at 1-877-527-0313 or visit
www.homedepot.com. Please reference your SKU (528-127 Olive
Stone fixture) or UPC (718212272039 Olive Stone fixture).
4. Keep your receipt and these Instructions for Proof of Purchase.
(not included):
Light Bulb
(100 watt maximum)
Flathead screwdriver
Wire strippers
Phillips screwdriver
Step Ladder
Chain Pliers
Electrical tape
Wire cutters
Page 3
PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):
3 Long Screw (#2)
3 Arm (#3)
1 Glass Shade (#6)
3 Short Screw (#4)
1 Metal Ring (#7)
1. Shut off power at the fuse box or circuit breaker box, if necessary remove old fixture
and all mounting hardware from outlet box.
Carefully unpack your new fixture and lay out all the parts on a clear area, Take care
not to lose any small parts necessary for installation.
Secure the one end of Arm (#3) to top coupling of Fixture Body (#1) and tighten with
Long Screw (#2). Do the same with the other arms.
Place Glass Shade (#6) over the Metal Ring (#7).
Connected the Metal Ring (#7) and the Shade (#6) as illustrated to the other end of
Arm (#3), secure with Short Screw (#4).
Page 4
2. Long Screw
1. Fixture Body
3. Arm
4. Short Screw
6. Glass Shade
7. Metal Ring
Page 5
PARTS INCLUDED FOR INSTALLATION (parts are not to scale):
1 Ceiling Loop with Chain (#11)
1 Nipple (#12)
1 Ground Screw (#16)
1 Quick Link (#8)
1 Lock Collar (#9)
1 Lock Washer (#14)
2 outlet Box Screw (#13)
1 Canopy (#10)
1 Hex Nut (#15)
1 Crossbar (#17)
3 Wire Connectors (#18)
1. Thread Nipple (#12) into Ceiling Loop (#11) until snug.
2. Thread other end of Nipple with Loop attached into crossbar (#17) until snug.
3. Place Lock Washer (#14) over end of Nipple protruding through crossbar and thread
Hex Nut (#15) onto nipple until tight.
4. Take the crossbar assembly and mount to ceiling outlet box (#19) with outlet box
screws (#13). Tighten screws securely with screwdriver.
5. By measuring determine correct number of links needed for proper hanging height.
Use a pair of pliers to open one end link of the chain and discard un- wanted chain.
(Don’t disregard the Quick Link linked at the end of Chain.)
6. Slip Canopy (#10) and Lock Collar (#9) through over the Ceiling Loop with Chain
(#11), then connect the other end of Ceiling Loop with Chain (#11) to Fixture Loop
by using Quick Link (#8).
7. Lace the fixture’s wires through the chain links and pull until taut. Feed the fixture
wires through the Lock Collar, Canopy, Ceiling Loop with chain and Nipple and pull
until taut.
8. Connect the ribbed wire from the fixture to the Neutral wire from the outlet box (#19)
and the smooth wire from the fixture to the hot wire from the outlet box (#19). Cover
the two wire connections using the two provided wire connectors (#18). Wrap the
two wire connections with electrical tape for a more secure connection. If your outlet
box has a ground wire (green or bare copper), connect fixture’s ground wire to it
using the wire connector (#18). Otherwise connect the copper ground from the
fixture to Ground screw (#16) on the Crossbar (#17). Note: If you have electrical
questions, consult your local electrical code for approved grounding methods.
9. Tuck these wire connections neatly into the ceiling outlet box and then raise the
canopy all the way to the ceiling. Raise the Lock Collar and thread onto Ceiling
Loop protruding through Canopy.
10. Install Light bulbs in accordance with the fixture’s specifications. (DO NOT
11. Installation is complete. Turn on the power at the circuit breaker or fuse box. Turn
the light switch on to activate the fixture.
Page 6
19. Outlet Box
18. Wire Connectors
15. Hex Nut
14. Lock washer
17. Crossbar
16. Ground screw
Ground Wire
Neutral Wire (Ribbed)
13. Outlet Box Screws
Hot Wire (Smooth)
12. Nipple
11. Ceiling Loop with Chain
10. Canopy
9. Lock Collar
8. Quick Link
Fixture Loop
Page 7
Bulb will not light.
Fuse blows or circuit
breaker trips when light
is turned on.
Possible Cause
1. Bulb is burned out.
2. Power is off.
Corrective Action
1. Replace light bulb.
2. Make sure power
supply is on.
3. Faulty wire connection.
3. Check wiring.
4. Faulty switch.
4. Test or replace switch.
Crossed wires or power wire Check wire connections.
is grounding out.
1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use
clean water, never a solvent) to wipe the glass and surface of the fixture.
2. To clean the inside of the fixture, first disconnect power to the fixture by turning off
the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly
dampened clean cloth (use clean water, never a solvent) to wipe the inside glass and
interior surface of the fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry
soft cloth to dust or wipe carefully.
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a
period of five (5) years from date of purchase. This warranty applies only to the original consumer
purchaser and only to products used in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the
manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident,
modifications, alterations, neglect or mishandling. This warranty shall not apply to any product that is found
to have been improperly installed, set-up, or used in any way not in accordance with the instructions
supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident,
misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material
or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface
and/or weathering, as this is considered normal wear and tear.
The manufacturer does not warrant and specially disclaims any warranty, whether express or implied,
of fitness for a particular purpose, other than the warranty contained herein. The manufacturer
specifically disclaims any liability and shall not be liable for any consequential or incidental loss or
damage, including but not limited to any labor / expense costs involved in the replacement or repair of
said product.
Page 8
Download PDF