TroposAir | 88400 | Installation guide | TroposAir 88400 Installation Guide

Owner’s Manual
Quantum
4UFOD52+LK+C
Cap for non-light use
This instruction contains 5 pages:
Page 1: Foreword
Page 2: Unpack and inspect parts contained
Page 3: Notes before installation and Hanging system installation
Page 4: Wire connection
Page 5: C anopy / Blade / Light kit installation
Page 6: Remote & Setting
Net weight
8.0 KGS.
3110124
17.6 LBS.
Toll Free: 1-855-676-7247
WARNING : Read and follow these instructions carefully and be mindful of all warnings shown throughout.
READ AND SAVE THESE INSTRUCTIONS
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY
TO PERSONS, PLEASE OBSERVE THE FOLLOWING :
1]. To ensure the success of the installation, be sure to read the instructions and review the diagrams
thoroughly before beginning.
2]. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
All electrical connections must be made in accordance with local codes, ordinances and/or the
National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and
products, secure the services of a qualified and licensed electrician as well as someone who can
check the strength of the supportive ceiling members and make the proper installations and
connections.
3]. Make sure that your installation site will not allow rotating fan blades to come in contact with any
object. Blades should be at least 7 feet from floor when fan is in operation.
4]. If possible, mount ceiling fan on a ceiling joist - the joist must be able to support the motion and weight
of the moving fan. If the fan will be mounted on a ceiling outlet box, a 4" x 2-1/8" deep METAL octagon
box is required ; one UL listed as " suitable for fan support ". The box and its supporting members must
not be able to twist or work loose. DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should
be performed by qualified personnel.
5]. Blades should be attached after motor housing is hung and in place. Fan motor housing should be
kept in carton until ready to be installed to protect its finish. If you are installing more than one ceiling
fan, make sure that you do not mix fan blade sets.
6]. After making electrical connections, spliced conductors should be turned upward and pushed
carefully up into outlet box. The wires should be spread apart with the grounded conductor and the
equipment - grounding conductor on one side of the outlet box and the " HOT " wires on the other side.
7]. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL/ETL listed
and should be installed per the light kit's installation instructions.
8]. After fan is completely installed, check to make sure that all connections are secure to prevent fan
from falling and/or causing damage or injury.
9]. The fan can be made to work immediately after installation. The bearings are adequately charged with grease,
so that under normal conditions, further lubrication should not be necessary.
10]. The fan must be turned off and stopped before reversing fan direction.
11]. This fan is suitable for slope ceiling.
12] . This fan is reversible.
13]. This fan includes optional light kit.
14]. This fan is controlled by remote.
15]. This fan is suitable for indoor use.
P1
Unpack and inspect fan carefully to be certain
all contents are included.
Mounting
Bracket
Hardware Bag
For Mounting Bracket:
Flat Washer x2
Spring Washer x2
Machine Screw x2 Wood Screw x2
Downrod
Assembly
For Wire Connection:
Wire Nut x 3
For Blade Installation:
Blade Screw x 9 (one spare screw included)
Canopy
Paper Washer x 9 (one spare washer included)
Yoke cover
For Blade Balance :
Balancing Slide x 1
Weight block (3G x 3)
3G
M
3G
M
Wires
Reverse Switch
(on top of motor)
Blade
Fan assembly
CFL Bulb (13W) x 2
Glass
Bottom Plate
Remote *Battery Included
Hardware Bag
Wood Screw x2
Wire Nut x6
P2
3G
M
WARNING: blades should be at least 7 feet from floor
Note 1:
Note 2:
Turn off power at breaker
box to avoid possible
electrical shock.
Use metal outlet box suitable
for fan support.
Outlet box must support 35 lbs min.
OFF OFF OFF
1. HANGING SYSTEM INSTALLATION
1A. Installing mounting bracket to ceiling outlet box
Install mounting bracket to outlet box in ceiling by using screws included with the outlet box and
washers from the hardware bag.
Outlet Box
Mounting
Bracket
1B. Installing Downrod and Yoke
1 Remove cross pin and cotter pin from downrod.
2 Insert downrod through canopy and yoke cover, and feed motor lead wires through downrod.
3 Loosen 2 downrod jam screws at yoke. Insert downrod assembly into yoke.
4 Insert the cross pin through yoke & downrod and secure with cotter pin.
5 Tighten both downrod jam screws to further secure downrod.
6 Pull down the yoke cover to cover yoke.
1 Cross Pin
2 Wires
1Cotter Pin
Canopy
Downrod
Assembly
Downrod
4 Cotter Pin
3
Downrod Jam
Screw(2)
( Loosen ing)
5
Downrod Jam
Screw(2)
(Tightening)
Yoke
Yoke cover
Yoke cover
6
4 Cross Pin
Yoke
1C. Hanging the fan
Rotate fan so that the groove on the ball engages
the ridge in the mounting bracket.
Lift fan assembly onto mounting bracket.
Mounting
Bracket
Ridge
Ball Groove
Fan Assembly
P3
Mounting
Bracket
2. WIRE CONNECTION
2A. Insert receiver into mounting bracket
NOTE: Do not sq u eeze all the wires while inserting the receiver into the mounting bracket.
Receiver
Mounting
Bracket
2B. Making electrical wire connection
Follow diagram below and make sure that all exposed wires are secured inside wire nuts.
Note: Wires from house may vary in color and may not include ground wire (green).
After wiring is completed, collect wires neatly inside hanging base.
From House
White
From Remote
White
White
Black
Black
From Fan
(AC-N)
Black
(Motor-N)
(AC-L)
(Motor-L)
White
Black
Blue
Blue
( for light kit )
Green
( from downrod )
( for ground wire )
Green
Green
Secure with twist - lock wire nuts.
( from mounting bracket )
2C. Setting code switches for transmitter
Remote controls are tuned to operate together using 4 switches for 16 possible code combinations.
1.Setting the code on the TRANSMITTER
1 Remove battery cover.
2 Slide code switch randomly using a small screwdriver or ball point pen to slide each switch firmly up or down.
3 Slide code switch for light ON/OFF (marked as X), or DIMMING (marked as D) function.
Important! This fan includes 2 CFL bulbs, so the code switch should be at X position (ON/OFF).
You may switch code at D position (DIMMING) once incandescent bulbs are installed.
4 Install 9V DC battery.(Included)
5 Install battery cover on transmitter.
2
Transmitter
Code Switches
O
N
D
1
2
3
4
X
3
D: for light dimming
(for incandescent bulbs )
X: for light ON/OFF
(for CFL bulbs)
15
4
! Warning! CFL bulbs are not applicable to the remote with dimming function.
P4
3. CANOPY INSTALLATION
Note: Two screws are pre-installed on mounting bracket for canopy installation.
1 Push up canopy until two screws pre-screwed on mounting bracket are engaged with two key holes on canopy.
2 Rotate canopy slightly until two pre-installed screw heads are engaged in the narrow end of key holes.
3 Tighten both screws.
1 Canopy
3 Screw (2)
2 Key Hole (2)
4. BLADE INSTALLATION (With Light Kit Pan Attached)
4A. Remove the plate at light pan that covers the rectangular hole.
4B. 1 Insert Blades into Blade slots of Rotating Band.
2 Fasten blades onto motor assembly through rectangular hole by using the washer & blade screws
provided from hardware bag.
4C. Re-attach the plate in place after blade installation is completed.
Blade Slot
Rotating Band
Rectangular Hole
Blade
Light Pan
1 Blade
2 Paper Washer (2)
2 Blade screw (2)
Plate
Plate
4B
4A
4C
5. LIGHT KIT INSTALLATION
For use with light kit:
For non-light use:
5A.
Install the bulbs (included) to the
medium sockets properly.
5C.
5B.
Attach the glass shade by screwing Attach the bottom plate by screwing
it clockwise onto the light kit pan.
it onto the light kit pan clockwise.
Groove
Bulb
(13W CFL bulb)
Bulb
(13W CFL bulb)
Medium Sockets
Glass
Shade
Turn on power at breaker box for remote setting.
P5
Bottom plate
6. REMOTE & SETTING
SETTING for light operation before starting fan.
Pressing the button “OFF” for 3~5 seconds till the LIGHT BLINKS , which means this remote control
has done the setting. Now the remote is ready for operation.
2
D: for light dimming
(for incandescent bulbs)
O
N
LOW:Fan low speed
HI:Fan high speed
MED
HI
D
1
2
LO W
O FF
OFF: For SETTING / Fan speed
: Button for ON/OFF Light
3
MED:Fan middle speed
4
X
X: for light ON/OFF
(for CFL bulbs)
Note: You may switch Light switch code at D position
(DIMMING) when you change to incandescent bulbs
for Down light. To use dimming, press and hold light
button(s).
P6
Download PDF