Hampton Bay | ES4697OB4 | Installation guide | Hampton Bay ES4697OB4 Installation Guide

Item #**********
Model #ES4679OB4
Safety Information
Pre-Installation
IMPORTANT SAFETY INSTRUCTIONS
(Save These Instructions)
TOOLS REQUIRED
□ Read all instructions prior to beginning the
USE AND CARE GUIDE
PENDANT FIXTURE
WARNING: Do not install this lighting
system in a wet location.
installation process.
□ Make sure the power is turned off at the
electrical panel box before beginning your
installation. Turning the power off at the wall
switch is not sufficient to prevent electrical
shock.
□ This fixture is intended to be mounted to a 4 in.
square x 2-1/8 in. deep metal octagon outlet box.
The box must be directly supported by the
building structure.
□ All electrical connections must be in accordance
with local codes and the National Electrical Code.
If you are unfamiliar with methods of installing
electrical wiring, secure the services of a
qualified licensed electrician.
Gloves
2 Installing the fabric shade
Safety goggles Phillips screwdriver Electrical tape
C
NOTE: Hardware not shown to actual size.
CAUTION: Keep the lamp away from
materials that may burn.
AA
Outlet box screws
x2
BB
Wire connectors
x3
3 Installing the chain assembly
CC
Mounting bracket assembly
x1
□ Remove the ring (F) from the loop of the chain assembly (A).
□ Adjust the chain to the desired length by removing links
if necessary.
□ Thread the chain assembly (A) through the canopy (D) and
leave the ring (F) under the canopy (D).
□ Thread the fixture wires up through the tube of the mounting
bracket assembly (CC).
□ Secure the mounting bracket assembly (CC) into the
chain assembly (A).
Installation
1
□ To clean the fixture, first disconnect the power to the fixture by turning off the circuit breaker or by
removing the fuse at the fuse box.
□ Use a dry or slightly dampened, clean cloth (use clean water, never use a solvent) to wipe the
interior and exterior surfaces of the xture.
□ Allow the fixture to dry completely before power is restored.
Installing the candle tubes and the bulb
□ Place the candle tubes (E) onto the sockets of the fixture body (B).
□ Install the light bulbs (sold separately).
E
CAUTION: Refer to the re-lamping label located on the
fixture. Do not exceed the recommended wattage.
CC
A
D
F
4 Installing the mounting bracket assembly
Outlet box
□ Make sure the power is off.
□ Pull the supply wires down out of the outlet box.
□ Attach the mounting bracket assembly (CC) to the existing
outlet box with the outlet box screws (AA) provided.
We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this pendant fixture.
We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of
products available for your home improvement needs. Thank you for choosing Hampton Bay!
CC
B
AA
Warranty
Pre-Installation
5-YEAR LIMITED WARRANTY
PACKAGE CONTENTS
5 Making the electrical connections
B
excludes liability for direct, incidental, or consequential damages. Some states do not allow exclusions
or limitations on an implied warranty, so the above exclusions and limitations may not apply. This warranty
E
Contact the Customer Service Team at 1-877-527-0313 or visit www.homedepot.com.
D
F
C
□ Attach the ground wire from the outlet box to the ground
screw on the mounting bracket (CC), which is green and
marked "GND".
□ Connect the negative wires (raised ribs without writing)
from the fixture to the negative wires from the supply
circuit, the positive wires (smooth with writing) from the
fixture to the positive wires from the supply circuit, and the
ground wire (bare) from the fixture to the ground wire from
the supply circuit using the wire connectors (BB).
□ Wrap electrical tape (not included) around the wire
connectors (BB), and ensure they are secure.
□ Push all excess wire and wire connections back
into the outlet box.
BB
Questions, problems, missing parts? Before returning to store,
call Commerial Electric Customer Service
8 a.m. - 6 p.m., EST, Monday - Friday
Part
A
Chain assembly
1
1-877-527-0313
B
Fixture body
1
C
D
E
F
Fabric shade
Canopy
Candle tube
Ring [preassembled on the chain assembly (A)]
1
1
3
1
Quantity
□ Raise the canopy (D) up to the outlet box.
□ Slide the canopy (D) over the loop of the chain assembly
(A), and secure it to the ceiling using the ring (F).
□ Adjust the length of the mounting bracket assembly (CC)
stud and hex nut if necessary.
Problem
Possible Cause
Solution
The light bulb will not
illuminate.
The light bulb is burned
out.
Replace the light bulb.
The power is off.
Make sure the power supply is on.
There is a faulty wire
connection.
Check the wiring.
Contact a quali ed and licensed
electrician if you are not comfortable
troubleshooting wiring problems.
There is a faulty switch.
Test or replace the switch.
CC
There are crossed wires,
The fuse blows or the circuit
breaker trips when the light bulb or the power wire is not
properly grounded.
is illuminated.
6 Installing the canopy
A
Description
Troubleshooting
Installation
of five year(s) from the date of purchase. If within this period the product is found to be defective in material
or workmanship, the product must be returned, with a copy of the bill of sale as proof of purchase, to the
original place of purchase. The manufacturer will, at its option, repair, replace, or refund the purchase price
Retain this manual for future use.
Wirestripper
A
B
CAUTION: Do not use chemical solvents or harsh
abrasives to clean the fixture or components, as damage
may occur.
HOMEDEPOT.COM
F
□ Place the fabric shade (C) onto the straight tube of the
fixture body (B).
□ Weave the fixture wires through the fabric shade (C) and
the chain assembly (A), up to the links and ring (F).
□ Screw the chain assembly (A) and the straight tube of
the fixture body (B) together to secure the fabric shade
(C) in place.
HARDWARE INCLUDED
CAUTION: Turn off/unplug the light and
allow it to cool before replacing the bulb.
Care and Cleaning
THANK YOU
Ladder
Installation
CC
A
D
F
Check the wire connections.
Download PDF