SoundStream Security System Guide
REV.5
RS.2
REMOTE VEHICLE STARTER
USER’S OPERATION GUIDE
FCC ID NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance void the user’s authority to operate
this device.
RS.2
IMPORTANT NOTES
OWNER'S MANUAL
ATTENTION
Please take a moment to review the safety precautions before
operating your system.
1) For safety reasons, the owner/user of this system MUST INSTALL
a CARBON MONOXIDE DETECTOR in the living area near to where
the vehicle is being stored or parked.
2) It is the sole responsibility of the owner/user to keep the remote
transmitters away from the reach of children and handle with care
so that the system does not unintentionally start.
3) When the vehicle is parked in an enclosed/partially enclosed area
(ex: garage, car port...), being serviced (ex: oil change) or the
vehicle is loaned to an operator not familiar with a remote starter,
the system MUST BE placed Service Mode.
4) MANUAL TRANSMISSION STARTERS Never install a automatic
remote start module into a manual transmission vehicle. Doing so
could result in EXTENSIVE DAMAGE TO YOUR VEHICLE,
PROPERTY DAMAGE AND POSSIBLY CAUSE SERIOUS INJURIES
OR EVEN DEATH. IF THIS SYSTEM WAS INSTALLED IN A MANUAL
TRANSMISSION VEHICLE, RETURN TO YOUR DEALER AND HAVE
IT DISABLED UNTIL THE CORRECT MODEL CAN BE INSTALLED.
5)NEVER REMOTE START THE SYSTEM IN AN ENCLOSED/
PARTIALLY ENCLOSED AREA!
RS.2
OWNER'S MANUAL
BUTTON
LOCK
QUICK VIEW CHART
BUTTON PRESS
CHIRP /
FLASH
SYSTEM FUNCTION
1 SECOND
1
LOCK DOOR’S
3 SECONDS
1
ACTIVATE PANIC MODE
PRESS THEN
RELEASE THEN
PRESS & HOLD
1
ACTIVATE CONSTANT LOCK
OUTPUT **
1 SECOND
2
UNLOCK DOOR’S
1 SECOND - 1 SECOND
3
DRIVER’S DOOR PRIORITY
(OPTIONAL / PROGRAMMABLE)
1 SECOND
1
ACTIVATES REMOTE STARTER
HOLD FOR 3 SECONDS
2
DEACTIVATE REMOTE STARTER
PRESS AND HOLD
FOR 3 SECONDS
2-1
ACTIVATES TRUNK RELEASE
HOLD FOR 3 SECONDS
1
ACTIVATES CAR FINDER MODE
1
ACTIVATES SILENT LOCK
2
ACTIVATES SILENT UNLOCK
UNLOCK
START
TRUNK
+
+
PRESS TOGETHER
THEN RELEASE
PRESS TOGETHER
THEN RELEASE
NO HORN HONKS - ACTS AS A TOGGLE - IF LOCK WILL UNLOCK, IF UNLOCK WILL LOCK.
RS.2
OWNER'S MANUAL
QUICK VIEW CHART
2ND CAR OPERATION AND PADLOCK
SECOND CAR OPERATION ALLOWS YOU TO CONTROL 2 VEHICLES WITH ONE REMOTE
TRANSMITTER. THIS WILL REQUIRE THAT YOU PRESS 2 BUTTONS AT THE SAME FOR
THE SECOND VEHICLE CONTROL. (CONTACT YOUR DEALER FOR MORE INFORMATION)
PADLOC- THIS FEATURE REQUIRES THAT YOU PRESS 2 BUTTONS AT THE SAME TIME
FOR EACH COMMAND TO YOUR VEHICLE. THIS FEATURE HELPS PREVENT ACCIDENTAL
REMOTE ACTIVATION. (SOME COMMANDS ARE NOT AVAILABLE WITH PADLOC)
SEE TRANSMITTER PROGRAMMING FOR MORE INFORMATION.
BUTTON PRESS
CHIRP /
FLASH
SYSTEM FUNCTION
HOLD FOR 1 SECOND
1
LOCK DOOR’S
HOLD FOR 3 SECONDS
1
ACTIVATE PANIC MODE
HOLD FOR 1 SECOND
2
UNLOCK DOOR’S
+
HOLD FOR 1 SECOND
2
DRIVER’S DOOR PRIORITY
(OPTIONAL / PROGRAMMABLE)
+
HOLD FOR 1 SECOND
1
ACTIVATES REMOTE START
HOLD FOR 3 SECONDS
2
DEACTIVATES REMOTE START
BUTTON
+
RS.2
OWNER'S MANUAL
PRESS & RELEASE
REMOTE STARTER ACTIVATION
1. Press and release the START button on the remote transmitter one time.*
*Press twice if the system is programmed for Safety Start.
2. The park lights will flash and the horn (optional) will Honk once as confirmation.
3. The vehicle will remote start and the park lights will turn on and remain on while the vehicle is
running under remote start**.
- If the remote start fails to start see the diagnostics chart at the back of the manual.
**DEFAULT RUNTIME OF THE SYSTEM IS 15 MINUTES.
TURN KEY ON
KEY TAKEOVER
Once the vehicle is remote started and you wish to enter the vehicle to drive away you must
preform the following steps.
1. Enter the vehicle then insert the key into the ignition switch.
2. Turn the key forward to the ON or RUN* position. (This is usually 2-3 key positions)
*Do not turn the key to the start position.
3. Step on the brake and the remote starter will turn off however the vehicle will continue to run
because the key is on. If the key is not in the on position when the brake is pressed the remote
starter and the vehicle will both shut off.**
** If the vehicle shuts down simply restart the engine with the key.
DO NOT TURN THE KEY TO THE START POSITION WHILE THE ENGINE IS RUNNING.
RS.2
SYSTEM OPERATIONS
OWNER'S MANUAL
PRESS & HOLD
REMOTE STARTER SHUT DOWN
1. While the vehicle is running with the remote starter press and hold the START button for three
seconds.
2. The park lights will flash and the horn (optional) will honk 2 times to confirm shutdown.
- Pressing the brake pedal or opening the hood will also shut down the remote starter.
THE VEHICLE WILL SHUT OFF WHEN THE RUNTIME EXPIRES (DEFAULT 15MIN)
PRESS & RELEASE
ENGINE IDLE MODE
This feature allows the user to safely leave the vehicle running without leaving the keys in the
ignition.
1. While the vehicle is running with the key press and release the START button then remove the
key from the ignition. The vehicle will run for 15 minute while you are away.
PRESS & RELEASE
EXTENDED RUNTIME
1. While the vehicle is running with the remote starter, press and release the START button.
2. The park lights will flash and the horn (optional) will honk one time as confirmation.
The system will reset the run time (See Example Below)**.
**Not available with 4 minute run time.
Example- If the vehicle has been remote started for 10 minutes and you press and release the
start button the system will run for a addition 15 minutes totalling 25 minutes of runtime.
PRESS & RELEASE
TURBO TIMER MODE
While the vehicle is running with the key, press and release the trunk button. The park lights will
turn on and the horn (optional) will Honk twice ( If connected the doors will unlock). When the
ignition key is turned to the “OFF” position the vehicle will remain running for 2 minutes.
*NOT AVAILABLE ON 2 BUTTON REMOTE.
RS.2
OWNER'S MANUAL
PRESS & RELEASE
1.
2.
3.
4.
Press and release the Lock Button on the remote transmitter.
The park lights will flash and the horn (optional) will Honk one time.
The doors will lock.
The LED will start flashing within five seconds.
NOTES:
- If the panic mode is activated pressing the lock button on the remote will stop the horn
from sounding.
- The horn can be programmed to honk with Car Finder and Panic Mode only.
- If the system is in Service Mode the doors will lock/ unlock but the horn will not honk.
- The LEDs will be on solid if the system is in Service Mode.
See Valet / Service Mode in this manual for further information
** Optional Feature may require additional parts and labor.
NEW- The LEDs can now be programmed not to flash when the doors are locked by
the remote transmitter.
*2 Button remote- The system must be programmed for 2 button remote lock/unlock
toggle to operate the lock feature on the vehicle. See dealer for more information.
PRESS & HOLD
TRUNK RELEASE
1.
2.
3.
4.
5.
Press then HOLD the Trunk Button on the remote transmitter.
The park lights will flash and the horn (optional) will honk two times.
The doors will unlock and the dome lights will activate. (optional)
The LEDs will stop flashing.
Continue to HOLD the Unlock Button until the trunk release activates.
NOTES: - For safety, the trunk release will not active when ignition key is ON.
** Optional Feature may require additional parts and labor.
RS.2
OWNER'S MANUAL
SYSTEM OPERATIONS
PRESS & RELEASE
UNLOCK DOORS
1.
2.
3.
4.
Press then release the Unlock Button on the remote transmitter.
The park lights will flash and the horn (optional) will honk two times.
The doors will unlock and the dome lights will activate. (optional)
The LEDs will stop flashing.
NOTES:
- If the panic mode is activated the first press of the unlock button will turn off the horn off and
the second press will unlock the doors.
- The horn can be programmed to honk with Car Finder and Panic Mode only.
- If the system is in valet mode the doors will lock/ unlock but the horn will not honk.
- The LEDs will be on solid if the system is in valet mode.
See Valet / Service Mode in this manual for further information
** Optional Feature may require additional parts and labor.
+
HOLD FOR 3 SECONDS
AUXILIARY OUTPUT 1
The Aux output can be programmed for a variety of custom applications.
(SEE DEALER FOR DETAILS)
1. Press and hold the UNLOCK and TRUNK Buttons for 3 seconds.
2. The system will unlock the doors then the AUX 1 output will activate.
3. Release the buttons for a momentary output or continue holding for up to a 5
second output.
This feature can be used to open the trunk, open or close power windows or control
sliding doors on minivans.
RS.2
OWNER'S MANUAL
PRESS HOLD
1.
2.
3.
4.
5.
Press and HOLD the Lock Button for three seconds.
The doors will lock.
The park lights will begin to flash and the horn will honk ON and OFF.
To turn off panic, press Lock or Unlock Buttons on remote.
If no button is pressed, Panic will stay active for 1 minute then turn off.
Panic Mode is a personal protection feature that allows you to activate your alarm from the
remote transmitter. This feature can be used to draw attention to your vehicle if you feel
threatened.
*NOTE AVAILABLE ON 2 BUTTON REMOTE.
+
PRESS TOGETHER
SILENT LOCK / SILENT UNLOCK
1. Press then release the Lock & Unlock buttons together.
2. If the system is UNLOCKED, it will Lock the doors with no horn honks. The park
lights will flash 1 time.
3. If the system is LOCKED, it will Unlock the doors with no horn honks. The park
lights will flash 2 times.
*NOT AVAILABLE ON 2 BUTTON REMOTE.
+
PRESS & HOLD for 3 sec
CAR FINDER MODE
1. PRESS & HOLD The UNLOCK and TRUNK Buttons on the remote transmitter for
5 seconds.
- The horn will honk 5 times and the park lights will flash 5 times.
This feature helps in locating your vehicle in a crowded parking lot. It allows you hear and see
your vehicle from a distance.
*Requires horn output connection and dealer programming.
RS.2
OWNER'S MANUAL
This feature is to be used if the remote transmitter is lost or is not communicating with
the system. This will disable the optional starter disable if installed. Follow the steps
below to deactivate your system.
ACTIVATING SERVICE MODE
Turn the Ignition Key ON
(Leave in the ON position)
Press and hold the Valet switch for 8 to 15 seconds
(Time depends on "Valet Settings" Program Option)
The horn will honk 5 times as confirmation that the system is
now in Service Mode. The LEDs on the antenna will
turn on solid while in Service Mode.
DEACTIVATING SERVICE MODE
Turn the Ignition Key ON
(Leave in the ON position)
Press and hold the Valet switch for 8 to 15 seconds
(Time depends on "Valet Settings" Program Option)
The horn will honk 2 times as confirmation that the system is
has exited Service Mode. The LEDs on the antenna will
turn off when Service Mode is off.
RS.2
OWNER'S MANUAL
COLD START MODE
Cold Start Mode will start the vehicle at a user selectable start cycle or temperature
(Temp Sensor Required).
EXAMPLE: If the 4 hour start cycle was selected, the vehicle will start once every 4
hours. The selected cycle will be active for 24hrs. (Default 15 minutes runtime)
Enter Cold Start Mode
Press and Hold LOCK and START for 3 seconds or until the park lights turn on.
While the park lights are on the start cycle may be selected. See below:
Press Start Cycle
Sets a ONE HOUR cycle. The park lights will flash ONCE as confirmation.
Sets a TWO HOUR cycle. The park lights will flash TWICE as confirmation.
Sets a THREE HOUR cycle. Park lights will flash THREE TIMES as confirmation.
Sets a FOUR HOUR cycle. Park lights will flash FOUR TIMES as confirmation.
NOTE: Timer Mode must be set each time the user wishes to use this feature.
To Cancel Timer Mode
Press and Hold LOCK and START for 3 seconds or until the park lights flash twice.
Note- Timer Mode will automatically turn off after 24 hrs. Pressing the brake pedal or
turning the ignition to the ON position will also cancel Timer Mode.
I
RS.2
OWNER'S MANUAL
Vehicle is not remote
starting?
- Count the park light flashes then see the diagnostics page.
- Check battery voltage in the remote.
- Make sure you are with-in operating range.
- Check if the vehicle anti-theft is activating.
- Reprogram the remote’s using Transmitter Program Mode.
- Check if the vehicle anti-theft is activating.
Vehicle starts then shuts - Is the starter motor staying on to log? If so,
off by itself
reprogram the tach and try again.
- See dealer if problem is not resolved.
The system does not
respond to the remote
transmitter
- Try your second remote.
- Check the batteries in the remote.
Reprogram the remote’s using Transmitter Program Mode.
- Make sure you are with-in operating range.
Doors do not lock
Or unlock
- Was this optional feature installed?
- Have your installer check the door lock connector.
- Have bypass or keyless module reprogrammed.
Horn does not honk
- Was this optional feature installed?
- Try panic mode to see if horn activates. If not,
have the systems horn output checked.
Lights on the antenna
are flashing
- When the doors are locked by the remote the LEDs will flash until the
unlock button is pressed.
- If you do not want the LEDs to flash have your installer program the
LED flashes off.
RS.2
OWNER'S MANUAL
DIAGNOSTICS
DIAGNOSTICS
Diagnostic Mode is a tool that can help trouble shoot a start fault. If the remote
starter fails to start i.e.: the hood is open the park likes will flash a diagnostic code.
i.e.: 5 flashes = start attempt with hood open. If the vehicle does not remote start,
count the park light flashes then compare it to the chart below.
PARK LIGHTS
LED FLASHES
DIAGNOSTICS / STATUS
3 SLOW FLASHES
LED’s ON SOLID
SYSTEM IS IN SERVICE MODE.
5 SLOW FLASHES
SERIES OF 5 FLASHES
START ATTEMPT WHILE IGNITION IS ON
5 FLASHES
SERIES OF 5 FLASHES
START ATTEMPT WITH HOOD SWITCH OPEN
6 FLASHES
SERIES OF 6 FLASHES
START ATTEMPT WITH BRAKE APPLIED
7 FLASHES
SERIES OF 7 FLASHES
SYSTEM IS IN TACH LOCK OUT (SEE DEALER)
8 FLASHES
SERIES OF 8 FLASHES
THREE START ATTEMPTS WITH NO START
The start fault must be corrected in order for the system to operate correctly. See
your dealer for additional trouble shooting.
USER NOTES
SOUNDSTREAM CAR ALARMS
CAR SECURITY SYSTEM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising