Minka Lavery | 2252-576 | Instructions / Assembly | Minka Lavery 2252-576 Instructions / Assembly

INSTALLATION INSTRUCTIONS
Item#2252 (New. 06/08/2013)
W ARNING !
READ AND SAVE THESE INSTRUCTIONS
S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig. 1)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture including the mounting
hardware.
2. Carefully remove the fixture from the carton and check that
all parts are included as shown in the illustration.
ASSEMBLING THE FIXTURE (Fig. 2)
3. Secure metal shade (J) to fixture body (Q) with socket ring
(M).
4. Determine the desired hanging height and thread rods (F1,
F2 and F3) to the nipple (I) of the fixture body (Q). Then
attach loop (H1) by screwing in to rod (F1). Note: remove
the nipple if installing with one 6” rod only.
5. Attach the quick link (G) to loop (H1) and loop (H2) on the
canopy (D). Carefully feed the wires over loop (H1), quick
link (G) and loop (H2).
6. Thread screws (A) into the pre-drilled holes in the circular
strap (B) spaced the same distance apart as the holes in
the canopy (D).
7. Attach the circular strap (B) to the Junction box using
mounting screws (C) (Size: #8-32N*L0.5”). The side of the
circular strap marked “GND” must face out.
CONNECTING THE WIRES (Fig. 3)
8. At this point, connect the electrical wires as shown in figure
3, making sure that all wire connectors are secured. If your
outlet has a ground wire (green or bare copper), connect
the fixture’s ground wire to it. Otherwise, connect the
fixture’s ground wire directly to the circular strap using the
green screw provided.
9. Tuck the wire connectors neatly into the ceiling Junction
Box and raise the canopy all the way to the ceiling.
COMPLETING THE INSTALLATION (Fig. 1)
10. Thread screws (A) into canopy (D), and secure with
knurled knobs (E).
11. Place the glass (N) into metal ring (O) and attach the clips
(P).
12. Install the light bulb(s) (not included) in accordance with
the fixture’s specifications. (DO NOT EXCEED THE
MAXIMUM WATTAGE RATING!) (NE PAS DEPASSER LA
PUISSANCE NOMINALE MAXIMALE!).
13. Secure clips (P) and decorative metal (K) to fixture body
(Q) with ball screws (L).
Fig. 1
H2
D
E
G
H1
F1
Rod# W30-1-77*1(F1)
W30-1-77*2(F2)
W30-H-77*1(F3)
Or: # W30-1-576*1(F1)
W30-1-576*2(F2)
W30-H-576*1(F3)
F2
F3
I
Q
J
K
L
M
N
O
P
Socket Ring # SKT-RING-26
Fig. 3
FIXTURE
WIRES
Black or
Smooth
Your installation is now complete. Return power to the junction
box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
Page: 1/2
Set# A-020
-Circular Strap
-Ground screw
-Mounting Screw*2
A
B
C
LA-2295E
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green
(Ground)
Fig.2
A
B
C
H2
D
E
G
H1
F1
a. Hardware Bag:
A. Screw*2
B. Circular Strap*1
D. Canopy *1
C. Mounting Screw*2
E. Knurled Knob*2
H. Loop*2
G. Quick Link*1
b. Hardware Bag:
F1. ROD 12"*1
F2. ROD 12"*2
F3. ROD 6"*1
Page: 2/2
B
D
F2
F1
LA-2295E
C
F3
A
E
G
H
Download PDF