Minka Lavery | 3138-284 | Instructions / Assembly | Minka Lavery 3138-284 Instructions / Assembly

INSTALLATION INSTRUCTIONS FOR FIXTURE #3138-284
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
ASSEMBLING THE FIXTURE (FIG. 1)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture including the mounting
hardware.
2. Carefully remove the new fixture from the carton and check that
all parts are included as shown in the illustration.
3. Thread the loop (A) onto the nipple (B) until snug.
4. Place the tubes (C) over the sockets (D).
5. Install the light bulbs (not included) in accordance with the
fixture’s specifications. (DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!) (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!).
6. Hang the crystal drops (F and I) onto the small rings (E) as
shown in Fig. 2.
7. Hang the crystal chain (H and G) onto the fixture as shown in
Figure 2.
MOUNTING THE FIXTURE (FIG. 2)
1. Thread the nipple (S) into the collar loop (T) until snug.
2. Thread the other end of nipple (S) into the cross bar (P).
3. Place lock washer (Q) and hex nut (R) over the end of nipple (S)
protruding through cross bar (P), then thread hex nut (R) to nipple
(S) until snug.
4. Take this crossbar assembly and mount to ceiling outlet box (V)
using outlet box screws (W). The side of cross bar marked
“GND” must face out.
5. Use proper chain pliers to open one end link of the chain and
connect to the fixture loop (A). Then close the link.
6. By measuring, determine the correct number of links needed for
the desired hanging height. Using the chain pliers, disconnect and
discard the remaining chain.
7. Carefully lace the fixture wires through the chain (X).
8. Slip the lock collar (Y) and canopy (U) over the chain (X), allowing
them to rest on the fixture loop (A).
9. Open the other end link of the chain (X) and connect to the collar
loop (T). Then close the link.
10. Feed the fixture wires through the collar loop (T) and nipple (S)
and pull until tight.
CONNECTING THE WIRES (See Wiring Diagram)
1. Connect the electrical wire as shown in the wiring diagram,
making sure that all wire connectors are secured. If your outlet
box has a ground wire (green or bare copper), connect the
fixture’s ground wire to it. Otherwise, connect the fixture’s
ground wire directly to the mounting plate using the green screw
provided.
2. Tuck the wire connectors neatly into the ceiling outlet box
and raise the canopy (U) to the ceiling. Then raise lock collar
(Y) and thread onto collar loop (T) protruding through
canopy (U).
Your installation is now complete. Return power to the outlet box
and test the fixture.
Fig. 1
LOOP(A)
NIPPLE(B)
CRYSTAL DROP(F)
TUBE(C)
SMALL RING(E)
CRYSTAL
CHAIN(G)
CRYSTAL
DROP(I)
SOCKET(D)
SMALL RING(E)
CRYSTAL DROP(F)
SMALL RING(E)
CRYSTAL CHAIN(H)
CRYSTAL DROP(F)
Fig. 2
Set A#A-010
-Crossbar
-Ground Screw
-Mounting screws (2)
Chain # HCH3072-284
Gauge 4.50MM
Notice: It is important to use proper chain pliers (not
included) to OPEN and CLOSE the chain included with
this fixture. Do not open them with other tools that may
twist or stress the chain links. It is important to use
proper chain pliers like the ones shown in the diagram.
Download PDF