Minka Lavery | 1545-77 | Instructions / Assembly | Minka Lavery 1545-77 Instructions / Assembly

INSTALLATION INSTRUCTIONS
Item#1545 (New. 08/29/2013)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
HANGING THE FIXTURE (Fig. 1)
1. Shut off the power at the fuse box or circuit
breaker. If necessary, remove the old fixture
including the mounting hardware.
2. Carefully remove the fixture from the carton and
check that all parts are included as shown in the
illustration.
3. Attach the mounting plate (A) to the outlet box
using two mounting screws (B) (Size:
#8-32N*L0.5”). The side of the mounting plate
marked “GND” must face out.
4. Place threaded rod (H) onto fixture body (I) and
place metal tube (G) over the threaded rod (H),
then place the nut (N1) over the metal tube (G)
and carefully pull the fixture’s wire through the nut.
5. Determine the desired length and thread the rods
(F) and nipple 1 to nut (N1), fasten the nut (N2)
and nipple 2 to the end of rods (F), then secure the
loop (E) to the end of rods (F).
6. By measuring, determine correct number of links
needed for proper hanging height. Using a pair of
chain pliers, disconnect and discard remaining
chain. Then attach the chain to loop (E) and the
loop on canopy (D). Carefully lace the fixture wires
through the chain, loop (E) and the loop on canopy
(D).
Fig. 1
A
C
D
B
Chain + Loop# HCH2012
Nipple 2
1/8 IP-27N
E
N2
F
Nipple 1
1/4 IP-18N
F
N1
G
L
K
M
J
CONNECTING THE WIRES (Fig. 2)
7. At this point, connect the electrical wire as shown
in figure 2, making sure that all wire connectors
are secured. If your outlet box has a ground wire
(green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s
ground wire directly to the mounting plate using
the green screw provided.
FINISHING THE INSTALLATION (Fig. 1)
8. Place canopy (D) over the mounting plate (A) and
secure with screws (C).
9. Place the glass shades (J) and metal rings (M)
over the socket and secure with socket rings (K)
by using spanner (L) provided.
10. Install the light bulb(s) (not included) in
accordance with the fixture’s specifications. (DO
NOT EXCEED THE MAXIMUM WATTAGE
RATING!) (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!)
Outlet Box
(Ceiling)
H
I
Rod# W35-1*3(F)
W35-H*1(F)
Spanner # WRH-T1-51
Socket Ring # SKT-RING-26
Set# A-021-126102
- Mounting Plate
- Ground Screw
- Mounting Screw*2
Fig. 2
FIXTURE
WIRES
Black or
Smooth
FIXTURE
WIRES
White or
Ribbed
FIXTURE
WIRES
Bare
Copper
(Ground)
Your installation is now complete. Return power to
the outlet box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
HOUSE
WIRES
Black
(Hot)
Notice: It is important to use proper chain pliers (not
included)
To OPEN and CLOSE the chain included with this fixture.
Do not open them with other tools that may twist or stress
the chain links. It is important to use proper chain pliers like
the ones shown in the diagram.
HOUSE
WIRES
White
(Neutral)
LA-1832E
HOUSE
WIRES
Green
(Ground)
Download PDF