Model No. PV-C2023-K Combination VCR Operating Instructions

Model No. PV-C2023-K Combination VCR Operating Instructions
Initial Setup
Combination VCR
Operating Instructions
PV-C2023-K
Basic Operation
Model No.
TV Operation
As an ENERGY STAR ® Participant, Panasonic has
determined that this product or product model meets the
ENERGY STAR ® guidelines for energy efficiency.
For assistance, please call : 1-800-561-5505 or visit us at www.panasonic.ca
LSQT0716A
Please read these instructions carefully before attempting to connect,
operate, or adjust this product. Please save this manual.
Timer Operation Advanced Operation For Your Information
• Initial Setup and Connection Procedures are on pages 8 and 9.
Important Safeguards and Precautions
READ AND RETAIN ALL SAFETY AND
OPERATING INSTRUCTIONS. HEED ALL
WARNINGS IN THE MANUAL AND ON UNIT
INSTALLATION
1 POWER SOURCE CAUTION
Operate only from power source indicated on unit or
in this manual. If uncertain, have your Electric Utility
Service Company or Video Products Dealer verify
your home power source.
2 POWER CORD PLUG
For safety, this unit has a polarized type plug (one
wide blade), or a three-wire grounding type plug.
Always hold the plug firmly and make sure your hands
are dry when plugging in or unplugging the AC power
cord. Regularly remove dust, dirt, etc. on the plug.
POLARIZED PLUG CAUTION:
The plug fits into outlet one way. If it cannot be fully
inserted, try reversing it. If it still will not fit, have an
electrician install the proper wall outlet. Do not tamper
with the plug.
GROUNDING PLUG CAUTION:
The plug requires a three-hole grounding outlet.
If necessary, have an electrician install the proper outlet.
Do not tamper with the plug.
3 POWER CORD
To avoid unit malfunction, and to protect against
electrical shock, fire or personal injury:
- Keep power cord away from heating appliances and
walking traffic. Do not rest heavy objects on, or roll
such objects over the power cord.
- Do not tamper with the cord in any way.
- An extension cord should have the same type plug
(polarized or grounding) and must be securely
connected.
- Overloaded wall outlets or extension cords are fire
hazards.
- Frayed cords, damaged plugs, and damaged or
cracked wire insulation are hazardous and should
be replaced by a qualified electrician.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat
generated during operation. If blocked, heat
build-up may result in a fire hazard or heat damage to
cassettes.
For your protection:
a. Never cover ventilation slots while unit is ON, or
operate unit while placed on a bed, sofa, rug, or
other soft surface.
b. Avoid built-in installation, such as a book case or
rack, unless properly ventilated.
5 AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE CHANGES
Do not place unit over or near a heater or radiator, in
direct sunlight, etc. If unit is suddenly moved from a
cold place to a warm place, moisture may condense in
unit and on the tape causing damage.
6 TO AVOID PERSONAL INJURY
• Never place unit on support or
stand that is not firm, level, and adequately strong.
The unit could fall causing serious injury to a child or
adult and damage to the unit.
• Move any appliance and
cart combination with care.
Quick stops, excessive
force, and uneven
surfaces may cause objects to
overturn.
• Carefully follow all operating
instructions.
2
OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION
An outside antenna or cable system must be properly grounded to
provide some protection against built up static charges and voltage.
Section 810 of the National Electrical Code, ANSI/NFPA 70 (in Canada,
part 1 of the Canadian Electrical
Code) provides information
NEC - NATIONAL
ANTENNA LEAD
ELECTRICAL CODE
IN WIRE
regarding proper grounding of
ANTENNA
GROUND
DISCHARGE UNIT
the mast and supporting
CLAMP
(NEC SECTION 810-20)
structure, grounding of the
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC
lead-in wire to an antenna
SERVICE
GROUND CLAMPS
EQUIPMENT
discharge unit, size of grounding
POWER SERVICE
GROUNDING
conductors, location of antenna
ELECTRODE SYSTEM
(NEC ART 250, PART H)
discharge unit, connection to
grounding electrodes, and
requirements for the grounding electrode.
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR
CIRCUITS
Locate an outside antenna system well away from power lines and
electric light or power circuits so it will never touch these power sources
should it ever fall. When installing antenna, absolutely never touch power
lines, circuits or other power sources as this could be fatal.
USING THE UNIT
Before unit is brought out of storage or moved to a new location,
refer again to the INSTALLATION section of these safeguards.
1 KEEP UNIT WELL AWAY FROM WATER OR MOISTURE,
such as vases, sinks, tubs, etc.
2 IF EXPOSED TO RAIN, MOISTURE, OR STRONG IMPACT,
unplug unit and have it inspected by a qualified service
technician before use.
3 ELECTRICAL STORMS
During a lightning storm, or before leaving unit unused for
extended periods of time, disconnect all equipment from the
power source as well as the antenna and cable system.
4 WHEN UNIT IS PLUGGED IN
• DO NOT OPERATE IF:
- liquid has spilled into unit.
- unit was dropped or otherwise damaged.
- unit emits smoke, malodors, or noises.
Immediately unplug unit, and have it inspected by a service
technician to avoid potential fire and shock hazards.
• Never drop or push any object through openings in unit.
Touching internal parts may cause electric shock or fire
hazard.
• Keep magnetic objects, such as speakers, away from unit to
avoid electrical interference.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.
6 CLEANING UNIT
Unplug unit. Use a clean, dry, chemically untreated cloth to
gently remove dust or debris. DO NOT USE cleaning fluids,
aerosols, or forced air that could over-spray, or seep into unit
and cause electrical shock. Any substance, such as wax,
adhesive tape, etc. may mar the cabinet surface. Exposure to
greasy, humid, or dusty areas may adversely affect internal
parts.
SERVICE
1 DO NOT SERVICE PRODUCT YOURSELF
If, after carefully following detailed operating instructions, the
unit does not operate properly, do not attempt to open or remove
covers, or make any adjustments not described in the manual.
Unplug unit and contact a qualified service technician.
2 REPLACEMENT OF PARTS
Make sure the service technician uses only parts specified by
the manufacturer, or have equal safety characteristics as original
parts. The use of unauthorized substitutes may result in fire,
electric shock, or other hazards.
3 SAFETY CHECK AFTER SERVICING
After unit is serviced or repaired, request that a through safety
check be done as described in the manufacturer’s service
literature to ensure video unit is in safe operating condition.
Safety Precautions
Warning :
Caution :
To prevent fire or shock hazard, do not expose this
equipment to rain or moisture.
To prevent electric shock, match wide blade of plug to wide
slot, fully insert.
This video recorder, equipped with the HQ (High Quality) System, is compatible with existing VHS
equipment. Only use those tapes with the
mark. It is recommended that only cassette tapes that
have been tested and inspected for use in 2, 4, 6, and 8 hour VCR machines be used. This television
receiver provides display of television closed captioning.
This symbol warns the user that uninsulated voltage within the unit
may have sufficient magnitude to cause electric shock. Therefore, it
is dangerous to make any kind of contact with any inside part of this
unit.
This symbol alerts the user that important literature concerning the
operation and maintenance of this unit has been included. Therefore,
it should be read carefully in order to avoid any problems.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS
INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
This product utilizes both a Cathode Ray Tube (CRT) and other components that contain lead. Disposal
of these materials may be regulated in your community due to environmental considerations. For
disposal or recycling information please contact your local authorities, or the Electronics Industries
Alliance: <http://www.eiae.org.>
Congratulations
Accessories
Remote Control
On your purchase of one of the most sophisticated
and reliable products on the market today. Used
properly, it will bring you and your family years of
enjoyment. Please fill in the information below. The
serial number is on the tag located on the back of
your unit.
LSSQ0380
Date of Purchase
Batteries 2 “AA”
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
PV-C2023-K
Loading the Batteries
Battery replacement caution
• Do not mix old and new batteries.
• Do not mix alkaline with manganese batteries.
Prevent Accidental Tape Erasure
Break off the tab to
prevent recording.
To record again.
Record
Tab
Cover the hole
with cellophane tape.
Screwdriver
3
Unit Information
Head Cleaning
Specifications
Playing older or damaged tapes may eventually
cause video heads to become clogged.
Display
Picture Tube
Head Clog Sensor
During playback this screen
appears if clogging is
detected. To clear message
from screen, press PLAY
on the remote or unit.
V I DEO HEADS MAY
NEED CLEAN I NG
PL EASE I NSERT HEAD
CLEAN I NG CASSETTE
OR REFER TO MANUAL
END : PLAY
• Use “dry” type head
cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)
• Follow cleaning tape directions carefully.
Excessive use of head cleaning tape can shorten
the video head life.
Features for a Quality Picture
Digital Auto Tracking
Continuously analyzes the signal and adjusts for
optimum picture quality.
Manual Tracking Control (to reduce picture noise)
Use during Playback and Slow Motion mode to
reduce picture noise. Press the 3 or 6 number key
on the remote control or CH
on the unit until
the picture clears up. To return to Auto Tracking,
press POWER off, then on again a few seconds
later.
Record/Playback Time
Only use tapes with the
Tape Speed
Setting
mark in this unit.
Type of Video Cassette
T60
T120
T160
SP
(Standard
Play)
1 Hour
2 Hours
2 Hours
40 Minutes
LP
(Long Play)
2 Hours
4 Hours
5 Hours
20 Minutes
SLP
(Super Long
Play)
3 Hours
6 Hours
8 Hours
VCR
Video Recording
System
Audio Track
Tuner
Broadcast Channels
CABLE Channels
FM Radio
Band Range
General
Power Source
Power
On
Power
Consumption Power
Off
Television System
Speaker
Operating
Temperature
Operating Humidity
Weight
Dimensions
(W X H X D)
20 inch measured diagonal 90°
deflection Picture Tube
2 rotary heads helical scanning
system
1 track
VHF 2 ~ 13, UHF 14 ~ 69
Midband A through I (14 ~ 22)
Superband J through W (23 ~
36) Hyperband AA ~ EEE (37
~ 64) Lowband A-5 ~ A-1 (95
~ 99) Special CABLE channel
5A(01) Ultraband 65 ~ 94, 100
~ 125
87.5 MHz ~ 108.1 MHz
120 V AC, 60 Hz
Approx. 110 W
Approx. 2.5 W
EIA Standard NTSC colour
1 pieces 1.5 W
5 °C ~ 40 °C (41 °F ~ 104 °F)
10 % ~ 75 %
23 Kg (50.6 lbs.)
515 mm X 505 mm X 474 mm
20-5/16″ X 19-7/8″ X 18-11/16″
Note
• Designs and specifications are subject to change
without notice.
DST (Daylight Saving Time)
Unit auto adjusts clock for DST (Daylight Saving
Time.)
■ Spring (First Sunday in April)
DST: ON ➞ Sets clock ahead one hour.
■ Autumn (Last Sunday in October)
DST: ON ➞ Turns clock back one hour.
• If your area does not observe Daylight Saving Time,
select DST: OFF.
• Keep these time changes in mind when
programming the unit for timer recordings.
4
Table of Contents
Tape Operation ...................................................................................... 24
Special VCR Features ........................................................................... 27
V-Chip Control Feature ......................................................................... 28
On-Screen Display (OSD) ..................................................................... 33
Before Requesting Service................................................................... 34
Limited Warranty/Servicentre List ....................................................... 35
Index ....................................................................................................... 36
Timer Operation Advanced Operation For Your Information
Timer Recording .................................................................................... 22
TV Operation
TV Operation .......................................................................................... 14
Picture Adjustment................................................................................ 15
TV Timer Features ................................................................................. 16
Closed Caption System ........................................................................ 18
FM Radio ................................................................................................ 20
Basic Operation
Reset Language, Channels, Clock, Time Zone Adjust....................... 10
Playback a Tape..................................................................................... 12
Record On a Tape.................................................................................. 12
Copy Your Tapes (Dubbing) ................................................................. 13
Initial Setup
Important Safeguards and Precautions ................................................ 2
Safety Precautions .................................................................................. 3
Unit Information....................................................................................... 4
Location of Controls ............................................................................... 6
Connections/Initial Setup (Ready to Play) ............................................ 8
5
Location of Controls
Remote Control Buttons
SLEEP
EJECT
Ejects tape.
POWER
Turns unit on or off.
Turns off the unit automatically.
NIGHT
Colour and picture intensity level
are adjusted during night time use.
FM/TV
DISPLAY
Receives FM radio signal.
Displays the VCR status and clock.
MUTE
RAPID TUNE
Mutes the sound instantly.
CHANNEL UP/DOWN
Selects a channel.
SELECT UP/DOWN
Controls navigation around
on-screen menu.
ACTION
Displays the last channel you were
watching.
VOLUME UP/DOWN
Adjusts volume.
SET/BACK SPACE
Sets a selected menu, or goes
back to correct.
Displays Main Menu.
PROGRAM
NUMBER Keys
Selects a channel directly.
Displays SET PROGRAM screen.
You can set Timer Program and
On-Timer.
PLAY
TRACKING UP/DOWN
Begins playback.
REWIND/SEARCH
Reduces picture noise during
Playback and Slow Motion.
Rewinds tape, and
searches reverse scene.
ADD/DELETE
PAUSE/SLOW
Pauses and slow motion
and frame advance picture.
CM SKIP/ZERO SEARCH
In Stop mode, goes to the
counter “0:00:00.” In Play
mode, skips over 1 to 3
minutes of tape.
Adds or deletes a channel.
FAST FORWARD/SEARCH
Fast forwards tape, and searches
forward scene.
SEARCH
Goes directly to the desired
recording. Locates end point of
recording.
TAPE POSITION
STOP
Finds out present tape
position and amount of tape
remaining.
REC
Stops recording or playback.
Records the program.
SPEED
Selects recording speed.
COUNTER RESET
Resets to “0:00:00” at the desired
position.
Note
• When EJECT is pressed, the tape is ejected from Cassette Compartment.
If EJECT is pressed during recording, the unit will not respond to the command.
6
Front View of the Unit and Indicators
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
Initial Setup
POWER
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
Built-In Speaker
AUDIO VIDEO IN Jack
For dubbing.
POWER
Turns unit on or off.
VOLUME UP/DOWN
Adjusts volume.
SET/BACK SPACE
Sets a selected menu, or
goes back to correct.
CHANNEL UP/DOWN
Selects a channel.
TRACKING UP/DOWN
Reduces picture noise
during Playback and Slow
Motion.
SELECT UP/DOWN
Controls navigation around
on-screen menu.
STOP
Stops recording or playback.
EJECT
Ejects tape.
ACTION
Press together with REW.
PHONES Jack
Connect an
earphone or
headphones.
REWIND/SEARCH
Rewinds tape,
and searches
reverse scene.
ACTION
Press together with
STOP.
PROG TIMER
Indicator
Lights when the
unit is set for
Timer Recording.
PLAY
Begins playback.
REPEAT
Repeats a recording.
ON TIMER Indicator
Lights when the
On-Timer is set.
REC Indicator
Lights during
recording.
FAST FORWARD/SEARCH
Fast forwards tape, and
searches forward scene.
Remote Sensor
REC
Records the program.
TIMER/FM
Sets a timer alarm up 60 min.
Enables FM Radio.
Rear View of the Unit
VHF/UHF
AC Power Plug
When plugged into an AC outlet, the
unit consumes 2.5 W of electric power
in OFF condition.
VHF/UHF Antenna Input Terminal
In from your Antenna or Cable (See
page 8).
7
Connections/Initial Setup (Ready to Play)
Please make all cable or antenna connections before power on.
Connecting
For ANT./Cable
Connect the cable from Antenna/Cable
to the VHF/UHF terminal on the unit.
UNIT (rear view)
For DSS/Cable Box
Connect the OUT jack on your cable
box to the VHF/UHF terminal on the unit
with a RF cable.
UNIT (rear view)
Cable TV
Converter Box
VHF/UHF
VHF/UHF
VHF/UHF
IN from
ANT./CABLE
VHF/UHF
IN from
ANT./CABLE
VHF/UHF
VHF/UHF
WARNING:
Overtightening “Nut type” RF coaxial cables may damage jacks. Finger tighten only.
Initial Setup (Ready to Play)
Press COMBO on the remote for Combo mode.
1
2
3
Plug the unit power cord into AC wall
outlet.
Press POWER on the remote or unit.
Press CH to
select English.
OR
Press CH to
select French
(Français).
OR
Press VOL+ to
select Spanish
(Español).
Auto channel and clock set starts.
CH AUTO SET PROCEEDING
AUTO CLOCK SET
PROCEEDING
CANCEL : STOP
8
• If you use a cable
box, turn it on and
set it to the Public
Broadcasting Service
(PBS) channel in your
time zone. If you use
a DSS receiver, it
must be turned off.
4
Settings are made automatically. When
setup is done, this screen appears.
2 / 6 / 2003 THUDST
12 ::00PM
ON
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
If AUTO
CLOCK SET IS
INCOMPLETE
screen appears,
set the clock using
MANUAL CLOCK
SET procedure on
next page.
AUTO CLOCK SET
IS INCOMPLETE
PLEASE SET CLOCK BY
PRESSING ACTION KEY
Notes
• Function buttons are inoperative during Initial
Setup.
• To remove a cassette during Auto Set, press
EJECT twice on the remote or STOP twice on
the unit. In this case, settings must be made
manually. (See page 10.)
• Depending on conditions, Auto Clock Set may
take longer than 30 minutes. If so, press STOP
to stop setup and perform settings manually.
(See page 10.)
Manual Clock Set
Reset all unit Memory Functions
When moving unit to a new location, or if a mistake
was made in the Initial Setup section.
• Make sure a tape is not inserted in the unit.
1
Press ACTION on the remote to display
SET CLOCK Menu screen.
Initial Setup
If AUTO CLOCK SET was incomplete, manually
set the clock as follows.
SET CLOCK
:
1/ /
DST : ON
SELECT :
END
: ACT I ON
2
SET :
Press
to select the month and
press to set. In the same manner,
select and set the date, year, time, and
DST. (Daylight Saving Time)
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
SET CLOCK
2 / 6 / 2003 THU 12: 00PM
DST : ON
1
Turn the unit
Power on.
2
Press and hold both
PLAY/REPEAT and FF on the
unit for more than 5 seconds.
SET COMPLETED
SET
:
START : ACT I ON
3
• The power will shut off.
• Please ignore “NO CASSETTE”
warning.
Press ACTION twice to start CLOCK and
exit.
3
Do “Initial Setup” on page 8.
POWER
ACTION
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
Note to CABLE System Installer
This reminder is provided to call the CABLE
(Cable TV) System Installers attention to
Article 820-40 of the NEC that provides
guidelines for proper grounding and, in
particular, specifies that the cable ground
shall be connected to the grounding system
of the building, as close to the point of cable
entry as practical.
9
Reset Language, Channels, Clock,
1
Press ACTION to display
M A I N MENU
LOCK LANGUAGE
TV
CH
CLOCK
MAIN MENU.
EX I T
SELECT :
SET
: ACT I ON
2
Language
1) Press
to
select language
icon.
EX I T
CLOCK
SELECT :
SET
: ACT I ON
MENU PR I NC I PAL
HOLA
BLOQUEO IDIOMA
CANAL
REL OJ
MENU
BONJOUR
BLOCAGE
LANGUE
CANAL HORLOGE SORT I E
SEL.
:
REGLER : ACT I ON
For French
M A I N MENU
CH
HELLO
LOCK LANGUAGE
CLOCK
CH
LOCK LANGUAGE
CLOCK
EX I T
TV
CH
LOCK LANGUAGE
CLOCK
EX I T
SELECT :
SET
: ACT I ON
2) Press ACTION.
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
WEAK S I GNAL D I SPLAY : OFF
SELECT :
END
: ACT I ON
For Spanish
TV
TV
2) Press ACTION.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
SAL I R
ELEG I R :
F I JAR : ACT I ON
TELE
M A I N MENU
SELECT :
SET
: ACT I ON
2) Press ACTION
repeatedly.
TV
1) Press
to
select “CLOCK.”
M A I N MENU
LOCK LANGUAGE
CH
to
1) Press
select “CH.”
M A I N MENU
TV
Clock
Channels
EX I T
SELECT :
SET
: ACT I ON
SET :
3) Press
to select
“ANTENNA,” then
press to set your
antenna system
(“TV” or “CABLE”).
4) Press
to select
“AUTO SET,” then
press .
• After Channel Auto Set is
finished, Clock Auto Set
will be performed. (If clock
is set manually, Clock Auto
Set will not be performed.)
SELECT :
END
: ACT I ON
SET :
(“TIME ZONE ADJUST” appears
only when auto clock is set.)
3) Press
to select
“MANUAL” or “AUTO
CLOCK SET” and
press .
• For Auto Clock Set, select
“AUTO CLOCK SET,” then
press .
SET CLOCK
2 / 6/2003 THU 12: 00PM
DST : ON
SELECT :
START : ACT I ON
SET :
For English
3) Press
to select “EXIT.”
Press ACTION
to exit.
10
4) Press
and
press
to select and
set the month, date, year,
time, and DST (Daylight
Saving Time).
5) Press ACTION twice to
start the clock and exit
this mode.
Time Zone Adjust
POWER
Time Zone Adjust
(Only when Auto Clock is set.)
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
ACTION
NUMBER Keys
ADD/DLT
M A I N MENU
LOCK LANGUAGE
TV
CLOCK
CH
EX I T
Basic Operation
1) Press
to
select “CLOCK.”
SELECT :
SET
: ACT I ON
2) Press ACTION.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : 0
ACTION key on
the unit
Using
STOP/EJECT REW/
SELECT :
END
: ACT I ON
keys
VOL
CH
SET :
ACTION
3) Press
to
select TIME ZONE
ADJUST and
press repeatedly
to select mode.
(See below.)
+1
0
-1
On Unit
You can operate the
menu screen using
unit buttons. To display
the menu, press
STOP/EJECT and
REW together with no
tape inserted. To exit
the menu, repeat above
with or without tape
inserted until normal
screen appears.
On Remote
On Unit
: CH UP
: CH DOWN
: VOLUME UP
: VOLUME DOWN
Whenever the menu or program
screen is displayed, CHANNEL
and
UP/DOWN function as
VOLUME UP/DOWN function
only.
as
SET CLOCK
Add or Delete a Channel
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUST : +1
SELECT :
END
: ACT I ON
SET :
To add channel:
To delete channel:
Select channel with
number keys and
press ADD/DLT.
Select channel with
or number keys
CH
and press ADD/DLT.
CHANNEL 08 ADDED
CHANNEL 08 DELE TED
4) Press ACTION
twice to exit.
11
Playback a Tape
Check List
Cable or antenna is connected.
Power cord is plugged in.
1
Insert a cassette.
• The unit power comes
on automatically.
Record tab
Record On a Tape
1
Insert a cassette with record tab
2
Press CH
channel.
3
Press SPEED to select
recording speed (see page 4).
SP = Standard Play
LP = Long Play
SLP = Super Long Play
To prevent tape jam,
remove loose or peeling
labels from tapes.
2
Press PLAY.
• Playback begins if cassette has no record
tab.
Notes
• These features work best in SLP mode.
• After the unit is in Still or Slow mode for 3 minutes, it
will switch to Stop mode automatically to protect the
tape and the video head.
Stop ➞ Press STOP
Rewind tape ➞ Press REW in Stop mode
Fast forward tape ➞ Press FF in Stop mode
Eject tape ➞ Press EJECT on the remote
or STOP/EJECT on the unit
You can operate using the
buttons on the unit
CH
PLAY
Insert a cassette.
REC
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
or number keys to select a
• For “LINE” input, see bottom of next page.
• Selected speed is displayed.
■ Forward/Reverse scene search
➞ Press FF or REW
➞ Press PLAY to release.
■ Still (Freeze) picture
➞ Press PAUSE/SLOW
➞ Press PLAY to release.
■ Slow Motion picture
➞ Hold down PAUSE/SLOW in
Still mode
➞ Press PLAY to release.
■ Frame by Frame picture
➞ Press PAUSE/SLOW in Still mode
➞ Press PLAY to release.
■
■
■
■
• The unit power comes on automatically.
AUDIO IN
ACTION
4
Press REC to start recording.
• To edit out unwanted portions, press
PAUSE/SLOW to pause and resume recording.
• You cannot view another channel during
recording.
■ Stop ➞ Press STOP
■ One Touch Recording (OTR)
Press REC repeatedly Normal Rec
to set the recording
length (30 min. - 4 hours). 4:00 3:00
0:30
2:00
• The unit stops recording at a preset time.
• PROG TIMER indicator lights on the unit.
Notes
• After the unit has been in Rec Pause mode for 5
minutes, it will stop automatically to protect the tape
and the video head.
• The remaining recording time of an OTR can be
displayed by pressing DISPLAY.
EJECT
DISPLAY
ACTION
NUMBER
Keys
REW
PAUSE/
SLOW
PLAY
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
TRACKING
ADD/DLT
FF
STOP
REC
SPEED
■ Press to stop and/or
eject tape.
12
REC Indicator
1:00
1:30
e
Copy Your Tapes (Dubbing)
Connections you’ll need to make.
Recording (Editing) unit
Playing (Source) VCR
AUDIO VIDEO
OUT
VIDEO IN AUDIO IN
Playback (Source)
1
2
3
Insert blank tape
with record tab.
Insert
pre-recorded
tape.
• Dubbing tapes protected with
Copy Guard will have poor
quality results.
Select “LINE” mode.
See “Selecting Input Mode” below.
Press PLAY then
Press REC, then
PAUSE at starting
PAUSE/SLOW
point to put in
immediately to put in
Standby mode.
Standby mode.
(Perform operation of steps 4 and 5 on both units at same time.)
4
5
Recording (Editing) unit
Basic Operation
IN
STOP
Press PLAY
to start dubbing.
Press PAUSE/SLOW
to start dubbing.
Press STOP
to stop dubbing.
Press STOP
to stop dubbing.
Selecting Input Mode
Method 1:
Press CH
Caution
• Unauthorized exchanging
and/or copying of copyrighted
recordings may be copyright
infringement.
. The display will change as follows.
1
LINE
2
3
(CABLE) (TV)
125 or 69
Method 2:
a Press ACTION for MAIN MENU.
to select “TV”, then press
b Press
ACTION for SET UP TV screen.
c Press
to select “INPUT SELECT,” and then
press to select “TUNER” or “LINE.”
d Press ACTION twice to exit this mode.
13
TV Operation
1
Press POWER on the remote or unit.
Check List
Cable or antenna is connected.
Power cord is plugged in.
2
CH 08
Use CH
or number
keys to select
a channel.
Press VOL + or
VOL - to adjust
volume.
3
24
VOL + / VOL-
NIGHT Mode
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
Colour and picture intensity levels are adjusted so
the screen is easier on your eyes during night time
use.
CH
NIGHT
Press NIGHT to
set NIGHT mode.
POWER
PHONES
Jack
• NIGHT mode may be
selected when watching
TV or playing a tape.
Press NIGHT to
cancel.
• Previous settings are
restored.
• NIGHT mode is cancelled
when power is turned
off or power failure
occurs.
■ Using the 100 key
When selecting CABLE channels 100 to 125 with the number keys, first press the 100
key, and then enter the remaining two digits.
■ Rapid Tune
Press R-TUNE to display the last channel you were watching.
■ Audio Mute
Press MUTE to instantly mute the sound. Press again to restore the previous sound level.
■ Phones
Connect an earphone (not supplied) or headphones (not supplied) to the Phones Jack.
14
Picture Adjustment
1
2
NIGHT
MUTE
CH
ACTION
VOL
UP/DOWN
NUMBER
Keys
TV
LOCK LANGUAGE
EX I T
CLOCK
1) Press
to select “TV.”
2) Press ACTION
to display SET
UP TV screen.
SELECT :
SET
: ACT I ON
3
SET UP TV
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
FM ANTENNA
SELECT :
END
: ACT I ON
4
: TUNER
: EXT
1) Press
to
select VIDEO
ADJUST.
to
2) Press
display screen.
SET :
COLOR
T I NT
BR I GHTNESS
P I CTURE
SHARPNESS
NORMAL
SELECT :
ADJUST :
END
: ACT I ON
1) Press
to
select an
adjustment
item. (See
below left.)
to
2) Press
adjust.
TV Operation
100 Key
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
M A I N MENU
CH
RAPID
TUNE
POWER
Press ACTION to display MAIN MENU.
COLOR
T I NT
BR I GHTNESS
P I CTURE
SHARPNESS
NORMAL
SELECT :
END
: ACT I ON
Picture Adjustment
SET :
To Reset Picture Controls,
press
and
to select and set “NORMAL.”
All controls return to their factory settings.
■ COLOR Control
Adjust colour intensity.
■ TINT Control
Adjust for natural flesh
tones.
5
Press ACTION three times to exit.
■ BRIGHTNESS Control
Adjust picture brightness.
■ PICTURE Control
Adjust picture intensity by
adjusting both contrast and
colour level in the proper
balance.
■ SHARPNESS Control
Adjust picture sharpness.
15
TV Timer Features
ON-TIMER with Alarm
This unit can be set to automatically power on in one of 3
modes (TV, Playback, or FM radio).
You can also combine the On-Timer with a one minute
alarm that gradually increases in volume.
1
Check List
The clock is set to the correct time.
Press PROG to display SET PROGRAM screen.
2
1) Press
to select “ON
TIMER.”
2) Press to display ON
TIMER screen.
SET PROGRAM
T I MER PROGRAMMING
ON TIMER
SELECT :
END
: PROG
SET :
1) Press
to select
desired settings.
2) Press to set the
ON-TIMER TIME or
ON-TIMER mode.
ON T I MER
3
6:--AM CH -ALARM : ON
SELECT :
END
: PROG
SET :
TIMER/FM
• Make sure a tape is inserted if Playback mode is selected.
• See “FM Radio” on pages 20 and 21 for instructions on how to
preset FM stations.
CH02
CH03
CH125
VCR
CH01
FM9
4
FM8
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
• ON-TIMER mode
selection order
VIDEO IN
AUDIO IN
ACTION
FM1
ON T I MER
6:00AM CH08
Press
to select
ALARM “ON” or “OFF.”
CH
ON TIMER
indicator
ALARM : ON
CANCEL : ADD / DLT
SET :
SELECT :
END
: PROG
When “ON” is selected, an alarm will gradually increase
in volume for one minute or until cancelled by pressing any
button (including VOL + -).
and
to move back
To Make Corrections, use
and correct.
5
Press PROG to set ON TIMER.
• “ON TIMER SET” is displayed.
• ON TIMER Indicator lights on the unit.
Note
To Cancel ON-TIMER,
Repeat steps 1 and 2. Then, press ADD/DLT to clear the
time in step 3. Now, press PROG to end.
“ON TIMER END” briefly appears on-screen.
16
• If no button on the remote or unit
(including a button used to turn
off the alarm) is pressed within 60
minutes after unit turns itself on,
it will turn itself back off.
Sleep Timer
This unit can be set for auto power off.
SLEEP
DISPLAY
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
PROG
ADD/DLT
Press SLEEP repeatedly
to set SLEEP TIMER.
• Pressing DISPLAY with sleep timer
set displays remaining time.
Press SLEEP repeatedly until
“SLEEP TIMER 00” appears to
cancel.
SLEEP TIMER 30
SLEEP TIMER 60
SLEEP TIMER 90
SLEEP TIMER 00
Instant Alarm
You can set a timer alarm up to 60 min. Useful when you
are cooking, etc.
00:00
• Pressing TIMER/FM repeatedly on the unit will
change display as follows.
One-minute
increase until 10:00
9:00
TV
10:00
20:00
(or LINE)
TV(or LINE)
FM
INSTANT ALARM
Screen Display
FM
To cancel, press TIMER/FM then press ADD/DLT on
the remote while CANCEL/SET screen is displayed.
30:00
50:00
INSTANT ALARM
Screen Display
Five-minute
increase until 30:00
25:00
40:00
in the order shown
left.)
Remaining Time
2:00
15:00
Press CH
on the
unit with CANCEL/SET
screen displayed to set
alarm. (Time changes
5 : 20PM
CANCEL : ADD / DLT
02 : 00
SET : CH
KEY ON UN I T
1:00 (one minute)
3:00
Press TIMER/FM on the unit to display the instant
alarm CANCEL/SET screen.
TV Operation
1
2
To increase timer in progress, repeat step 2. Time
will be rounded up to next 1, 5, or 10 minute interval.
(See chart left.)
Ten-minute increase
until 60:00
60:00 (Max)
<Example>
• If current time remaining is 12:15, countdown will restart
from 15:00.
• If current time remaining is 9:15, countdown will restart
from 10:00.
Note
• While timer function is in progress, you
can change channels on the unit with
while “CANCEL/SET” screen is
CH
not displayed.
3
Alarm will sound at 0:00.
Press any button to stop.
• The volume of the alarm gradually increases for one
minute and then continues to beep until any button is
pressed.
17
Closed Caption System
Closed Caption is ...
This multi-use system not only allows the hearing impaired to enjoy selected programs, but also makes
useful information from TV stations available to everyone.
Closed Caption Mode Feature
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
LOCK LANGUAGE
TV
CH
EX I T
CLOCK
1) Press
to
select “TV.”
2) Press ACTION to
display SET UP TV
screen.
SELECT :
SET
: ACT I ON
3
SET UP TV
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
FM ANTENNA
: TUNER
: EXT
SELECT :
END
: ACT I ON
1) Press
to select
“CAPTION.”
to display
2) Press
CAPTION screen.
SET :
Closed Caption Mode
Selections
Caption Mode: CAP C1 or C2
A narration of selected
TV programs is displayed.
Check TV program listings for CC
(Closed Caption) broadcasts.
Caption Mode: TEXT C1 or C2
The lower half of the screen will
be blocked out. When the TV
station broadcasts information,
such as program listings, it will
appear in this space.
Caption Mode: OFF
Closed Caption / Text narration
will not be displayed.
NOTES :
4
CAPT I ON
CAPT I ON MODE
CC ON MUTE
: CAP C1
: CAP C1
SELECT :
END
: ACT I ON
SET :
OFF
1) Press
to select
CAPTION MODE.
repeatedly
2) Press
to select mode.
(See left.)
CAP C1
TEXT C2
• The closed caption or text signal
may be broadcast over C1, C2, or
both. Also, text contents can vary
so you may wish to try different
settings.
• While recording one station and
watching another, Captioning will
not be displayed.
TEXT C1
CAP C2
5
Press ACTION three times to
return to the normal screen.
Recording and Playing Back a Closed Caption/Text Program
Record:
Record normally.
Closed Caption/ Text signal, if present, is recorded automatically.
Playback: Start playback. Do above steps to select desired caption mode.
18
Caption On Mute Feature
Closed Caption narration, if available, is displayed when
MUTE button is pressed for silence.
1
MUTE
2
M A I N MENU
LOCK LANGUAGE
TV
CH
EX I T
CLOCK
1) Press
to
select “TV.”
2) Press ACTION to
display SET UP TV
screen.
SELECT :
SET
: ACT I ON
ACTION
3
SET UP TV
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
FM ANTENNA
: TUNER
: EXT
SELECT :
END
: ACT I ON
4
1) Press
to select
“CAPTION.”
to display
2) Press
CAPTION screen.
SET :
CAPT I ON
CAPT I ON MODE
CC ON MUTE
: OFF
: CAP C1
SELECT :
END
: ACT I ON
SET :
TV Operation
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
Press ACTION to display MAIN MENU.
1) Press
to select
CAPTION MODE.
repeatedly to
2) Press
select “OFF.”
to select
CC ON MUTE.
2) Press
repeatedly to
select desired mode.
1) Press
5
SELECT :
END
: ACT I ON
NO
SET :
• Each press of
will change
the display as shown left.
• The caption may be broadcast
over CAP C1 or C2.
CAP C1
CAP C2
6
Press ACTION three times to
return to the normal screen.
7
Press MUTE to mute the sound and display
closed captioning.
• To cancel, press MUTE again.
19
FM Radio
FM Radio is ...
This unit has an FM radio with built-in antenna, 9 station preset, and a band range of 87.5 ~ 108.1 MHz.
You can set the On-Timer (page 16) to wake up to your favourite radio station.
FM Radio Setup
FM ANTENNA Setup
1
Press FM/TV on the remote or press
TIMER/FM twice on the unit to display FM
radio mode.
2
Press a number
key (1~9) to select
the FM number.
1 2 : 0 0PM
FM 1
87. 5MHz
Make sure FM tuning is done correctly
(see FM Radio Setup).
1
Press ACTION
to display MAIN MENU.
2
M A I N MENU
TV
CH
3
1 2 : 0 0PM
FM 1
8 7. 7MHz
MEMORY : PRESS ADD / DLT KEY
1 2 : 0 0PM
FM 1
1) Press CH
to
select the desired
radio station.
(Each press
changes frequency
0.2 MHz.)
2) Press ADD/DLT
to set the radio
station.
Hold down CH
or for a few
seconds, then
release to quickly
scan for FM
stations in your
area.
• To cancel, press
CH or while
in search mode.
To Make Corrections,
select station with a number key,
then do step 3 again.
To exit FM mode,
press FM/TV on the remote or
TIMER/FM twice on the unit.
20
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
8 7. 7MHz
MEMOR I ZED
LOCK LANGUAGE
1) Press
to select “TV.”
2) Press ACTION
to display SET
UP TV screen.
4
1) Press
to
select FM
: TUNER
ANTENNA.
: I NT
to
2) Press
select “INT
SELECT :
SET :
(INTERNAL)”
END
: ACT I ON
or “EXT
■ For cable TV users (EXTERNAL)”
whichever
➞ “INT”
■ For antenna users sounds the
best.
➞ “EXT”
SET UP TV
CAPT I ON
INPUT SELECT
V I DEO ADJUST
FM ANTENNA
Press ACTION twice to end setup.
How to use the FM radio
1
Press FM/TV on the remote or press
TIMER/FM twice on the unit to display FM
radio mode.
2
1 2 : 0 0PM
FM 1
87. 5MHz
Press a Number
key (1~9) to
select a preset FM
number (see “FM
Radio Setup” on
page 20).
To cancel, press FM/TV on the remote or
TIMER/FM twice on the unit.
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
Notes
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
TIMER/FM
FM/TV
CH
ACTION
TV Operation
• FM radio cannot be recorded on a Video cassette.
• You may get better reception by repositioning the
unit.
• You cannot select FM Radio mode during playback or
record, or while a blue back screen (PROG, ACTION,
MENU) is displayed.
• Once stations are set, the selected station and current
time are displayed when FM Radio mode is entered.
To remove time, press DISPLAY. If DISPLAY is
pressed again, the unit status screen appears.
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
NUMBER
keys
ADD/DLT
21
Timer Recording
You can set up to 8 programs to be recorded while you are
away.
1
2
Press PROG to display SET PROGRAM screen.
SELECT :
END
: PROG
3
1) Press
to select
TIMER
PROGRAMMING.
2) Press to display
screen.
SET PROGRAM
T I MER PROGRAMMING
ON TIMER
DATE
• If a program is already in
, and to
memory, press
select an unused program
number.
SET :
START
STOP
Press
to select and
or to set the
recording DATE.
CH
7 FR I --:-- --:-- -TODAY
SP
-----------------------SELECT :
END
: PROG
Check List
Cable or antenna is connected.
Power cord is plugged in.
The clock is set to correct time.
The tape is long enough.
The record tab is in place.
• 1~31 = One time
• DAILY = MON~FRI
• WEEKLY SUN~SAT
= Same time once a week
SET :
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
Today’s
Date
8
7
9
31
SELECT
/
WEEKLY
(SAT)
1
2
6
Selection Order
WEEKLY
(MON)
DAILY
WEEKLY
(SUN)
Repeat step 3 to set:
• Start time, Stop time
• Channel (or LINE for outside source)
• Speed (SP, LP, SLP)
4
P
1
2
3
4
DT
day
----
START
9 : 00 p
-- : --- : --- : --
STOP
12 : 00a
-- : --- : --- : --
CH SPD
08 SP
-- --- --- --
CANCEL : ADD / DLT
SELECT :
SET :
END
: PROG
5
22
AUDIO IN
ACTION
Example
Press PROG to
end the program.
To Enter More Programs,
press
to select
and to set a blank
program number, and
then repeat step 3.
Press PROG twice to exit this mode.
• If you’re using a cable box, make sure that it is tuned
to the desired channel and the power is left on for timer
recording.
• PROG TIMER indicator lights on the unit.
PROG TIMER indicator
Cancel a Timer Recording:
(Recording is in progress)
Hold down STOP for a few
seconds to cancel the Timer
Recording.
• Any future daily or weekly recordings
will be performed as programmed.
Review, Replace or Clear Program
Contents : (Recording is not in progress)
Repeat steps 1 and 2 on page 22.
1
2
P
1
2
3
4
DT START STOP CH SPD
day 9 : 00p 12 : 00a 08 SP
8 10 : 00a 12 : 00p 125 SP
10 8 : 00p 9 : 00p 10 SP
SU 9 : 00p 10 : 00p L LP
Press
to select the
desired program.
CANCEL : ADD / DLT
SELECT :
SET :
END
: PROG
3 To Replace program...
DATE
START
STOP
CH
1) Press
to display.
to select
and press or
to set new program
contents.
3) Press PROG.
8 SAT 9:00P 12:00A 08 2) Press
TODAY
SP
----------------------------------------------
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
PROG
SELECT :
END
: PROG
SET :
To Clear program...
STOP
DT START STOP CH SPD
-- -- : -- -- : -- -- -8 10 : 00p 12 : 00a 125 SP
10 8 : 00p 9 : 00p 10 SP
SU 9 : 00p 10 : 00p L LP
Press ADD/DLT.
CANCEL : ADD / DLT
SELECT :
SET :
END
: PROG
4
Press PROG twice to exit this mode.
Timer Operation
P
1
2
3
4
ADD/DLT
Notes
• 2 minutes before Timer recording is performed, “PLEASE
PREPARE FOR TIMER REC” appears and/or the PROG
TIMER Indicator flashes. Be sure a cassette with record tab is
loaded and the unit is in Stop mode.
• If the start times of two programs overlap, the lower numbered
program will have priority.
• If the start time for a Timer Recording comes up during a
normal recording or One Touch Recording (page 12), the Timer
Recording will not be performed.
• If there is a power interruption of more than one minute, the
recording may not be performed or continued.
• If “INCOMPLETE” appears after all items have been set, check
all entries and make necessary corrections.
23
Tape Operation
Search System is ...
Each time a recording is made, an invisible index mark is placed on the tape. When timer recordings are
made, program index and information are also included. These index marks can be used to access or
scan recordings.
Index Search
Go directly to the desired recording.
1
Press SEARCH in
Playback or Stop
mode to display
INDEX SEARCH
screen, and then
press number keys
to select the recording
number.
I NDEX SEARCH
ENTER I NDEX NUMBER : 1
US I NG 1- 9 KEYS
FORWARD SEARCH : FF
REVERSE SEARCH : REW
EX I T : SEARCH
• To calculate number, see
below.
NUMBER Keys
Press FF or REW to
start search.
2
FF
SEARCH
REW
Play begins at
search end.
To search forward
or back 1 index,
press FF or REW
while screen
left is displayed
(10 sec.).
I NDEX SEARCH
FORWARD SEARCH : FF
REVERSE SEARCH : REW
To cancel, press
PLAY.
■ To calculate the Index Number
Example 1:
To go to rec. 2 from rec. 4, enter 3 and press REW.
1
2
3
4
5
6
7
Example 2:
To go to rec. 6 from rec. 2, enter 4 and press FF.
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
1
2
3
4
5
6
7
NOTE: indicates start points of each recording.
Note
• If Index Search is started very close to an index mark, that
index mark may not be counted in the search.
24
FF
REW
Auto Operation Functions
■ Auto Shut Off
No broadcast signal in TV (Only when
Weak Signal Display is set to OFF),
blank tape is Played for 5 minutes
➞ Power turns off
• This feature is cancelled if any button is
pressed during above mode.
■ Auto Playback
Insert a tape in Power off mode
➞ Power turns on
• Playback begins if tape has no record tab.
■ Auto Rewind
Tape reaches its end
➞ Rewind ➞ Stop
■ Playback Auto Eject (Repeat Play is “OFF”)
Tape with no record tab reaches its end
Rewind ➞ Stop ➞ Eject
Tape Position Display
To find out present tape position.
Tape position is displayed for VHS-C Cassettes
type, tapes under 30 minutes, and some other
tapes, but the position is not correct.
1
Press TAPE POSITION to detect current tape
position.
• “DETECTING TAPE
POSITION” only appears the
first time a cassette is inserted
and it takes several seconds
for correct indication to appear.
• The present tape position
indication is displayed.
TAPE
POSITION
BEG I N
2
END
Advanced Operation
DETECT I NG TAPE POS I T I ON
Press TAPE POSITION (or wait 5 seconds)
to return to the normal screen.
25
Tape Operation (continued)
Repeat Play
Zero Search
To quickly return to a specific tape counter
location.
1
Press COUNTER RESET during
playback to display the Counter.
2
0 : 00 : 00
Set to see a recording over and over.
In PLAY mode,
press
PLAY/REPEAT
on the unit to
turn “ON.”
PLAY
REPEAT ON
PLAY
REPEAT OFF
Press COUNTER
RESET at the
desired position to
reset to “0:00:00.”
Repeat above to
turn “OFF.”
Note
3
Continue playback, rewind, or fast
forward.
4
Press STOP.
5
• Playback repeats when tape end is reached or
unrecorded portion over 30 seconds is detected.
DISPLAY
1 : 23 : 45
Press CM/ZERO in
stop mode to start
ZERO SEARCH.
PLAY
FF
STOP
CM/ZERO
REW
• Unit goes into FF or REW mode and stops at the last
point the Counter was set to 0:00:00.
COUNTER
RESET
Commercial Skip
By pressing the CM/ZERO button in Playback
mode you can skip over 1 to 3 minutes of recorded
tape in just a few seconds.
Press CM/ZERO repeatedly to select skip
time in Play mode.
• No indication appears.
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
PLAY/REPEAT
26
Special VCR Features
Weak Signal Display ON/OFF
When “ON” is selected, the picture is displayed even when
a broadcast signal is weak or non-existent.
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
LOCK LANGUAGE
TV
CH
CLOCK
EX I T
1) Press
to
select “CH.”
2) Press ACTION to
display SET UP
CHANNEL screen.
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
SELECT :
SET
: ACT I ON
ACTION
3
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
WEAK S I GNAL D I SPLAY : OFF
SELECT :
END
: ACT I ON
1) Press
to select
WEAK SIGNAL
DISPLAY .
to set “ON” or
2) Press
“OFF.”
SET :
Notes
• “ON” = Picture is displayed regardless of signal condition,
and may not always be clearly visible.
“OFF” = Screen turns solid blue when signal is absent or
weak.
• If unit is connected to equipment which has blue back feature,
selecting “ON” will have no effect on the other equipment.
4
Press ACTION twice to
return to the normal screen.
Advanced Operation
VCR Lock
All operations are prohibited except Timer recording and
tape eject. Useful for families with small children.
VCR LOCK ACT I VATED
VCR LOCK OFF
In stop mode, hold
down REC on the
unit without a cassette
inserted for 7 seconds
to turn “ON.” Please
ignore NO CASSETTE
warning.
Repeat above with or
without cassette to turn
“OFF.”
• VCR Lock is cancelled automatically after about 24 hours if
clock is set.
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC TIMER/FM
REC ON TIMER PROG TIMER
VIDEO IN
AUDIO IN
ACTION
REC
27
V-Chip Control Feature
Process of V-Chip Control Feature
Enter Code
Setup
Blocking
V-Chip Control Feature is...
This unit has a built-in V-Chip Control
which allows you to block unwanted TV
usage based on US MOVIES, US TV
PROGRAMS Ratings, Canadian English
Language Ratings and Canadian French
Language Ratings.
Enter Secret Code
A 4-digit code must be entered to view a blocked program
or change rating settings.
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
TV
CH
LOCK LANGUAGE
CLOCK
1) Press
to select
“LOCK.”
2) Press ACTION to
display screen.
EX I T
SELECT :
SET
: ACT I ON
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
NUMBER Keys
ACTION
ADD/DLT
3
LOCK
ENTER 4-D I G I T CODE
----
1) Press NUMBER keys
to enter your secret
code.
2) Enter same code again
for confirmation.
ENTER : 0 - 9
END
: ACT I ON
• Step 2) not necessary when
changing rating or secret
To Make Corrections
code.
Press repeatedly to move • Take care that you are not
observed entering the secret
the cursor. Press number
code.
keys to make the correction.
4
LOCK
CONF I RM 4-D I G I T CODE
****
****
RECOGN I ZED
CHANGE CODE : ADD / DLT
CONT I NUE :
END
: ACT I ON
Press
to display LOCK menu
(see page 29-32).
Or
Press ACTION
twice to exit.
Changing your secret code
• You will need your current code. Do steps 1 ~ 3.
In step 4, press ADD/DLT to clear current code.
Repeat steps 3 and 4 to enter new code.
Notes
• DO NOT forget your secret code.
• Once ratings are set, restricted tapes or programs cannot be
accessed unless the secret code is entered.
28
If LOCK menu is not displayed, do “Enter Secret
Code” steps on page 28.
Setup US MOVIES Ratings
1
LOCK
US MOVIES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
END
: ACT I ON
SET :
1) Press
to
select US
MOVIES.
2) Press to set
“ON” or “OFF.”
■ “ON” ➞V-Chip Control is activated.
■ “OFF” ➞V-Chip Control is deactivated.
2
LOCK
US MOVIES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
END
: ACT I ON
3
SET :
V I EW NR PROGRAMS? : YES
G
UNLOCKED
PG
PG-13
R
NC-17
X
CONTA I NS NO RAT I NG
SELECT :
SET :
END
: ACT I ON
Process of V-Chip Control Feature
Enter Code
1
SELECT :
END
: ACT I ON
SET :
2
1) Press
to
select
VIEW NR
PROGRAMS?.
2) Press to set
“YES” or “NO.”
3
LOCK
US MOVIES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
END
: ACT I ON
SET :
V I EW NR PROGRAMS? : YES
UNLOCKED
TV-Y
FV
TV-Y7
TV-G
V S L D
TV-PG
V S L D
TV-1 4
V S L
TV-MA
CONTA I NS NO RAT I NG
SELECT :
SET :
END
: ACT I ON
5
1) Press
to
select
CHANGE
SETTINGS.
2) Press to
display screen.
1) Press
to select
VIEW NR
PROGRAMS?.
2) Press to set
“YES” or “NO.”
NR (Not Rated) PROGRAMS
Some TV shows, such as news, sports,
weather, bulletins, emergency information
usually have no ratings.
4
V I EW NR PROGRAMS? : YES
UNLOCKED
TV-Y
FV
TV-Y7
TV-G
V S L D
TV-PG
V S L D
TV-1 4
V S L
TV-MA
FOR ALL CH I LDREN
SELECT :
SET :
END
: ACT I ON
Note
Press ACTION to redisplay LOCK menu
and continue with US TV PROGRAMS
Ratings Setup (this page). Or, press
ACTION three times to exit.
1) Press
to
select US TV
PROGRAMS.
2) Press to set
“ON” or “OFF.”
■ “ON” ➞V-Chip Control is activated.
■ “OFF” ➞V-Chip Control is deactivated.
1) Press
to
select
CHANGE
SETTINGS.
2) Press to
display screen.
Press
to select
and to set ratings
to be blocked. (See
page 31.)
LOCK
US MOVIES
: OFF
CHANGE SETT I NGS
: OFF
US TV PROGRAMS
CHANGE SETT I NGS
NEXT PAGE
• You may select from
standard TV ratings (chart
1), or customize to a specific
content rating (chart 2).
5
Press
to
select and to set
ratings to be
blocked.
(See page 31.)
• Ratings highlighted
in Green will be
blocked. Ratings in
white letters will not
be blocked.
Advanced Operation
V I EW NR PROGRAMS? : YES
G
UNLOCKED
PG
PG-13
R
NC-17
X
GENERAL AUD I ENCE
SELECT :
SET :
END
: ACT I ON
Blocking
Setup US TV PROGRAMS Ratings
NR (Not Rated) PROGRAMS
Some movies, such as old movies or foreign
movies usually have no ratings.
4
Setup
Press ACTION three times to exit this
mode.
29
V-Chip Control Feature (continued)
If LOCK menu is not displayed, do “Enter
Secret Code” steps on page 28.
Canadian English Language Ratings
1
SELECT :
END
: ACT I ON
2
SET :
1) Press
to
select NEXT
PAGE.
2) Press to
display screen.
SET :
1) Press
to
select
CANADIAN
ENGLISH.
2) Press to set
“ON” or “OFF.”
LOCK
US MOVIES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
NEXT PAGE
LOCK
SELECT :
END
: ACT I ON
■ “ON” ➞V-Chip Control is activated.
■ “OFF” ➞V-Chip Control is deactivated.
3
SELECT :
END
: ACT I ON
4
SET :
V I EW E PROGRAMS? : YES
C
UNLOCKED
C8+
G
PG
1 4+
1 8+
EXEMPT
SELECT :
SET :
END
: ACT I ON
V I EW E PROGRAMS? : YES
SELECT :
END
: ACT I ON
6
30
SET :
LOCK
1
US MOVIES
: OFF
CHANGE SETT I NGS
US TV PROGRAMS
: OFF
CHANGE SETT I NGS
NEXT PAGE
SELECT :
END
: ACT I ON
2
SET :
LOCK
CANADIAN ENGLISH : OFF
CHANGE SETT I NGS
CANADIAN FRENCH : OFF
CHANGE SETT I NGS
PREVIOUS PAGE
SELECT :
END
: ACT I ON
SET :
1) Press
to
select NEXT
PAGE.
2) Press to
display screen.
1) Press
to
select
CANADIAN
FRENCH.
2) Press to set
“ON” or “OFF.”
■ “ON” ➞V-Chip Control is activated.
■ “OFF” ➞V-Chip Control is deactivated.
1) Press
to
select VIEW E
PROGRAMS?.
2) Press to set
“YES” or “NO.”
4
Press ACTION to redisplay LOCK menu
and continue with Canadian French
Language Ratings Setup. Or, press
ACTION four times to exit.
Blocking
Canadian French Language Ratings
3
Press
to
select and to
set ratings to be
blocked. (See
ratings chart on
next page.)
Setup
Enter Code
1) Press
to
select
CHANGE
SETTINGS.
2) Press to
display screen.
E (Exempt) PROGRAMS
Some TV shows, such as news, sports,
weather, bulletins, and emergency
information usually have no ratings.
5
Process of V-Chip Control Feature
LOCK
CANADIAN ENGLISH : OFF
CHANGE SETT I NGS
CANADIAN FRENCH : OFF
CHANGE SETT I NGS
PREVIOUS PAGE
SELECT :
END
: ACT I ON
SET :
V I EW E PROGRAMS? : YES
G
UNLOCKED
8 ANS+
13 ANS+
16 ANS+
18 ANS+
EXEMPT
SELECT :
END
: ACT I ON
1) Press
to
select
CHANGE
SETTINGS.
2) Press to
display screen.
1) Press
to
select VIEW E
PROGRAMS?.
2) Press to set
“YES” or “NO.”
SET :
E (Exempt) PROGRAMS
Some TV shows, such as news, sports,
weather, bulletins, and emergency
information usually have no ratings.
5
V I EW E PROGRAMS? : YES
G
UNLOCKED
8 ANS+
13 ANS+
16 ANS+
18 ANS+
GENERAL AUD I ENCE
SELECT :
SET :
END
: ACT I ON
6
Repeatedly press
to select and
to set ratings to
be blocked. (See
ratings chart on
next page.)
Press ACTION four times to exit this
mode.
US MOVIES RATINGS
G
PG
GENERAL AUDIENCE:
All ages admitted.
PARENTAL GUIDANCE:
Some material may not be suitable for
children.
PARENTS CAUTIONED:
PG-13 Some material may be inappropriate for
children under 13.
RESTRICTED:
R
Children under 17 must be
accompanied by a parent or adult.
OVER AGE 17 ONLY:
NC-17
No one 17 and under admitted.
X
ADULTS ONLY:
US TV PROGRAMS RATINGS:Chart 1
TV-Y
TV-Y7
TV-G
TV-PG
TV-MA
G
General
8 ANS + Not recommended for young children
13 ANS +
Programming may not be suitable for
children under the age of 13
16 ANS +
Programming is not suitable for
children under the age of 16
18 ANS + Programming restricted to adults
Canadian English Language RATINGS
C
C8+
Children
Children 8 years and older
G
General Audience
PG
Parental Guidance
14+
Viewers 14 years and older
18+
Adult Programming
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
ACTION
Advanced Operation
TV-14
FOR ALL CHILDREN:
Content specifically geared to young
viewers ages 2-6.
FOR AGE 7 AND OLDER:
May contain mild physical or comedic
violence which may frighten children
under 7.
GENERAL AUDIENCE:
Contains little or no violence, strong
language, or sexual dialogue or
situations.
PARENTAL GUIDANCE:
May contain infrequent coarse
language, limited violence, some
suggestive sexual dialogue and
situations.
PARENTS CAUTIONED:
May contain sophisticated themes,
sexual situations, strong language, and
more intense violence.
MATURE AUDIENCE:
May contain mature themes, profane
language, graphic violence, and sexual
situations.
Canadian French Language RATINGS
US TV PROGRAMS RATINGS: Chart 2
FV
Fantasy Violence
V
Violence
S
Sexual Situations
L
Adult Language
D
Sexually Suggestive Dialogue
31
V-Chip Control Feature (continued)
Process of V-Chip Control Feature
Enter Code
Setup
Blocking
Blocking Message
DISPLAY
<When V-Chip Control is activated>
• If a program or movie exceeds the ratings you have set, a
message will appear on a black background and sound is
muted.
CH08
CH08
PROGRAM RAT I NG EXCEEDED
PROGRAM RAT I NG EXCEEDED
RAT I NG : 1 3ANS+
ACCESS CODE
RAT I NG : PG-1 3
ACCESS CODE
----
ENTER : 0-9
ACTION
----
ENTER : 0-9
<Canadian Rating>
<US Rating>
To View a Blocked Program / Movie
[Temporarily Deactivate V-Chip Control]
Enter your secret code (ACCESS CODE) in the
Blocking Message screen.
• V-Chip Control is reactivated when power is turned off
or power failure occurs.
[Deactivate V-Chip Control]
Enter your secret code (steps 1-3 page 28).
Then, set US MOVIES and/or US TV PROGRAMS
and/or CANADIAN ENGLISH LANGUAGE and/or
CANADIAN FRENCH LANGUAGE to “OFF”
and .(Ratings set on pages 29, 30 are
using
retained and will be in effect when V-Chip Control is
activated again.)
• If DISPLAY is pressed, even when V-Chip control is
deactivated, rating is displayed on-screen.
STOP
1 1 : 0 0AM
CH08
0 : 12 : 34
SP
RAT I NG : 13 ANS+
STOP
1 1 : 0 0AM
CH08
0 : 12 : 34
SP
RAT I NG : PG-1 3
<Canadian Rating>
<US Rating>
• If DISPLAY is pressed, even when no V-Chip data, “NO
V-CHIP DATA” is displayed on-screen.
STOP
1 1 : 0 0AM
NO V-CH I P DATA
32
CH08
0 : 12 : 34
SP
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
On-Screen Display (OSD)
VCR Status & Clock Display
Press DISPLAY to display or remove
the overlay.
Blue Screen Display
Whenever a blank section of a tape comes up in
Play mode, or when the selected channel has no
broadcast signal with the Weak Signal Display set
to “OFF” (see page 27), the screen will turn solid
blue.
Channel
Function Status
Current Time
REC
0 : 25
Rec Time
Remaining
(OTR mode
only, see
page 12.)
Counter
CH08
1 2 : 0 0PM
-0 : 1 2 : 3 4
SP
Channel & Function Display
When a function button is pressed (PLAY, FF, etc.)
or you change channels, the unit mode or channel
number will be displayed.
NO V-CHIP DATA
CH 08
Tape Speed
Warning and Instruction Displays
OSD
These displays will alert you to a missed
operation or provide further instructions.
CAUTION
Page
If you attempt to set or review a Timer Recording, or
set the On-Timer and the Clock is not set...
8 - 11
CHECK CASSETTE RECORD TAB
If you press REC, and a cassette is inserted with no
record tab...
3, 12
TO CANCEL TIMER REC HOLD
DOWN STOP KEY FOR APPROX 3
SEC
If you press STOP during a Timer Recording...
23
NO CASSETTE
If you press PLAY, FF, REW, or REC without a
cassette inserted...
12
PLEASE PREPARE FOR TIMER
REC
If the unit is not in Stop mode or a cassette with
record tab is not inserted two minutes before a Timer
Recording is about to begin...
VIDEO HEADS MAY NEED
CLEANING PLEASE INSERT HEAD
CLEANING CASSETTE OR REFER
TO MANUAL END: PLAY
If head cleaning becomes necessary while playing
back a tape...
VCR LOCK ACTIVATED
If you press a function button other than STOP/EJECT or
POWER while the unit is in VCR Lock mode...
22 - 23
4
27
For Your Information
PLEASE SET CLOCK BY
PRESSING ACTION KEY
33
Before Requesting Service
Check the following points once again if you are having trouble with your unit.
Power
No power…
Monitor
No picture or sound...
Poor picture with normal sound...
Poor sound with normal picture...
Poor TV reception...
No colour or poor colour...
Ghost (multiple) images...
TV programs cannot be
watched...
Channel cannot be selected...
VCR
TV program cannot be
recorded...
Timer recording cannot be
performed…
CORRECTION
•
•
•
•
•
•
•
•
Make sure your antenna system (TV or CABLE), is correctly set. (P.8)
Completely insert Power Plug into an AC outlet.
Set POWER button to ON.
Adjust BRIGHTNESS, SHARPNESS, and PICTURE controls in the SET UP TV
menu. (P.15)
Adjust VOLUME control. (P.14)
Adjust SHARPNESS and PICTURE controls in the SET UP TV menu. (P.15)
Adjust TINT and COLOUR controls in the SET UP TV menu. (P.15)
Install a directional antenna.
• Make sure the selected channel is in unit’s memory. (P.10, 11)
• Only the channel being recorded can be viewed on this unit.
CORRECTION
•
•
•
•
Make sure your antenna system (TV or CABLE), is correctly set. (P.8)
Make sure cassette record tab is intact. (P.3)
Check that clock is set to current time and date.
Make sure DSS/CABLE box (if used) is left on and tuned to channel to be
recorded.
• Set recording Start/Stop times correctly. (P.22-23)
• Timer recording may not be performed or continued if a power interruption
of more than 1 minute occurs before or during a Timer Recording, even after
power is restored.
No playback picture, or the
playback picture is noisy or
contains streaks...
• Adjust TRACKING control in either direction. (P.4)
• Try Head Cleaning. (P.4)
VCR cannot be controlled...
• Make sure VCR LOCK is set to off. (P.27)
• Make sure unit is not in a Timer Record operation.
Remote Control
Unit cannot be controlled...
CORRECTION
•
•
•
•
Aim remote at remote sensor on unit (P.7) so that signal is unobstructed.
Inspect the remote batteries. (P.3)
Make sure VCR LOCK is set to off. (P.27)
Exposing unit remote sensor to direct fluorescent or outdoor light may cause
signal interference.
ACTION, PROG and FM/TV
buttons cannot be selected...
• Check remote batteries.
Miscellaneous
CORRECTION
Video cassette cannot be
inserted...
Video cassette cannot be
removed...
Tape cannot be ejected or
inserted...
Video cassette ejects when a
recording is started, or the power
is turned off for timer recording...
In Stop mode, the VCR motor
(CYLINDER) continues to
rotate...
VCR cannot be controlled...
34
CORRECTION
• Completely insert Power Plug into an AC outlet.
• Set POWER button to ON.
• Insert the cassette window side up; record tab facing you.
• Completely insert Power Plug into an AC outlet.
• Try ejecting or inserting the tape again after turning POWER off, then back on.
• Make sure cassette record tab is intact. (P.3)
• To enable Quick Play mechanism, the VCR cylinder will rotate for about 3
minutes. This reduces response time from Stop to Play mode and from Play to
Rewind Search mode.
• Make sure VCR LOCK is set to off. (P.27)
Limited Warranty/Servicentre List
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
PANASONIC PRODUCT – LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship and
agrees to remedy any such defect for a period as stated below from the date of original purchase.
COMBINATION VHS VCR TV / VCR DVD TV:
21″ and under
Carry-in Service
Only
One (1) year, parts (including Picture Tube) and
labour
22″ and over
In-home Service
One (1) year, parts (including Picture Tube) and
labour
In-home Service will be carried out only to locations accessible by roads and within 50 km of an authorized
Panasonic service facility.
LIMITATIONS AND EXCLUSIONS
This warranty does not apply to products purchased outside Canada or to any product which has been
improperly installed, subjected to usage for which the product was not designed, misused or abused,
damaged during shipping, or which has been altered or repaired in any way that affects the reliability
or detracts from the performance, nor does it cover any product which is used commercially. Dry cell
batteries are also excluded from coverage under this warranty.
This warranty is extended to the original end user purchaser only. A purchase receipt or other proof of
date of original purchase is required before warranty service is performed.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, EXCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES.
In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, or the exclusion of implied warranties, so the above limitations and exclusions
may not be applicable.
WARRANTY SERVICE
For product operation and information assistance, please contact your Dealer or our Customer Care
Centre at: Telephone #: (905) 624-5505
Fax #: (905) 238-2360
Web: www.panasonic.ca
For product repairs, please contact one of the following:
• Your Dealer who will inform you of an authorized Servicentre nearest you.
• Our Customer Care Centre at (905) 624-5505 or www.panasonic.ca
• A Panasonic Factory Servicentre listed below:
Calgary, Alberta
Mississauga, Ontario
Lachine, Québec
Panasonic Canada Inc.
12111 Riverside Way
Richmond, BC V6W 1K8
Tel: (604) 278-4211
Fax: (604) 278-5627
Panasonic Canada Inc.
6835-8th St. N. E.
Calgary, AB T2E 7H7
Tel: (403) 295-3955
Fax: (403) 274-5493
Panasonic Canada Inc.
5770 Ambler Dr.
Mississauga, ON L4W 2T3
Tel: (905) 624-8447
Fax: (905) 238-2418
Panasonic Canada Inc.
3075, rue Louis A. Amos
Lachine, QC H8T 1C4
Tel: (514) 633-8684
Fax: (514) 633-8020
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and preferably in the original carton.
Include details of the defect claimed, and proof of date of original purchase.
For Your Information
Richmond, British Columbia
35
Index
4
2
5
A
4
4
2
4
6
7
0
9
2
2
9
7
2
7
8
4
2
2
3
5
B
Accessories ................................................................ 3
Audio Mute ............................................................... 14
Auto Operation Functions......................................... 25
Before Requesting Service....................................... 34
Blocking Message .................................................... 32
Blue Screen Display ................................................. 33
C
Canadian English Language Ratings ....................... 30
Canadian French Language Ratings........................ 30
Caption On Mute Feature ......................................... 19
Channel & Function Display ..................................... 33
Channel (SET UP CHANNEL).................................. 10
Clock (SET CLOCK)................................................. 10
Closed Caption Mode Feature.................................. 18
Commercial Skip ...................................................... 26
Connections................................................................ 8
Copy Your Tapes (Dubbing)..................................... 13
D
DST (Daylight Saving Time) ....................................... 4
E
Eject Tape ................................................................ 12
Enter Secret Code .................................................... 28
F
Fast Forward ............................................................ 12
Features for a Quality Picture..................................... 4
FM Radio ............................................................ 20–21
Forward Search ........................................................ 12
Frame by Frame Advance ........................................ 12
Front Panel Indicators ................................................ 7
3
2
3
4
7
7
H
8
2
2
8
6
ON-TIMER with Alarm .............................................. 16
One Touch Recording .............................................. 12
P
Phones ..................................................................... 14
Picture Adjustment ................................................... 15
Playback tape ........................................................... 12
R
Rapid Tune ............................................................... 14
Record ...................................................................... 12
Record/Playback Speed Settings ............................... 4
Remote Control Buttons ............................................. 6
Repeat Play .............................................................. 26
Reset all unit Memory Functions ................................ 9
Reverse Search........................................................ 12
Rewind...................................................................... 12
S
Selecting Input Mode................................................ 13
Sleep Timer .............................................................. 17
Slow Motion .............................................................. 12
Special VCR Features .............................................. 27
Specifications ............................................................. 4
Still (Freeze) Picture ................................................. 12
Stop .......................................................................... 12
T
Tape Erasure Prevention............................................ 3
Tape Position Display............................................... 25
Timer Program Review, Replace, Clear ................... 23
Timer Recording ....................................................... 22
Timer Recording Cancellation .................................. 23
Time Zone Adjust ..................................................... 11
TV Operation ............................................................ 14
TV Timer Features.............................................. 16–17
Head Cleaning............................................................ 4
U
I
Important Safeguards and Precautions ...................... 2
Index Search ............................................................ 24
Initial Setup................................................................. 8
Instant Alarm ............................................................ 17
Unit, Front View .......................................................... 7
Unit, Rear View........................................................... 7
Using the 100 key..................................................... 14
US MOVIES RATINGS............................................. 31
US TV PROGRAMS RATINGS ................................ 31
L
V
Language ................................................................. 10
Limited Warranty/Servicentre List............................. 35
Loading the Batteries.................................................. 3
Location of Controls................................................ 6–7
V-Chip Control Feature....................................... 28–30
VCR Lock ................................................................. 27
VCR Status & Clock Display..................................... 33
W
M
Manual Clock Set ....................................................... 9
Warning and Instruction Displays ............................. 33
Weak Signal Display ON/OFF .................................. 27
N
Z
NIGHT Mode ............................................................ 14
LSQT0716A
O
Panasonic Canada Inc.
5770 Ambler Drive,
Mississauga, Ontario L4W 2T3
(905) 624-5010
www.panasonic.ca
Zero Search.............................................................. 26
Montréal:
3075 Louis A. Amos, Lachine, Québec H8T 1C4 (514) 633-8684
Toronto:
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-8447
Calgary:
6835 - 8th Street N.E., Calgary, Alberta T2E 7H7 (403) 295-3955
Vancouver:
12111 Riverside Way, Richmond, BC V6W 1K8 (604) 278-4211
K
Printed in Indonesia
LSQT0716A
S0103-0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement