Minka Lavery | 953-126 | Installation guide | Minka Lavery 953-126 Installation Guide

INSTALLATION INSTRUCTIONS FOR 953-126
WARNING!
SHUT
POWER OFF AT
FUSE OR
ASSEMBLY THE FIXTURE (Fig.1)
1.
2.
3.
4.
5.
6.
7.
Thread the center column (B) into the center of main body (G),fit the loop
(A) on top of center column (B).
Install the light bulbs in accordance with the fixture’s specifications. DO
NOT EXCEED THE MAXIMUM WATTAGE RATING!
Thread the pipe (K) onto bottom center of main body (G) and lock it securely
with nut (J).
Screw the nut (W) onto pipe (K). Put washer (X) and rubber ring (Y) over the
pipe (K). Raise glass shade (M) to bottom of main body (G),Then position
the finial base(L) below the glass shade. Protruding the pipe (K) from base
(L) and attach the base (L) to the fixture assembly (V) by lock it securely
with hexnut (O).(Four holes on fixture assembly(V) must be aligning with
the holes of main body(G).
Hook the slice side of arm (N) to hooks on the main body (G),aligning the
hole on arm (N) with the hole of main body (G),then guide the other side
through(V),attach collar ring (I) onto top side of arm(N) and lock securely
with screw(H), attach collar ring(Q) on other side of arm(N)and tighten
firmly with hexnut (R).
Thread pipe (S) into hexnut (O) and tighten firmly with screw (P). Attach
finial base (T) and tighten firmly with finial (U).
Cover two glass plates (F) over main body (G).(smooth side will be on the
bottom),attach collar ring (E)and lock securely with nut (D).Hook end of
decoration chain to the loops on center column (B) and the loops on arm (N).
HANG THE FIXTURE (Fig.3)
1. Shut off the power at the circuit breaker and remove old
fixture from ceiling, including the old crossbar.
2. Carefully unpack new fixture and lay all the parts on a clear surface.
3. Thread nipple (C) into loop (F) until snug.
4. Thread other end of nipple (C) with loop attached into crossbar (D) until
snug.
5. Place lock washer (B) over end of nipple protruding through crossbar
and thread hex nut (A) onto nipple until tight.
6. Take this crossbar assembly and mount to ceiling junction box with
junction box screws (E). Tighten screws securely with screwdriver.
7. Use a pair of pliers to open one end link of the chain provided and
connect to the fixture loop(J). Close the link.
8. By measuring, determine correct number of links needed for proper
hanging height. Using pliers, disconnect and discard remaining chain.
9. Lace the fixture wires through the chain.
10. Slip loop collar (H) over the chain, then do the same with the canopy
(G).
11. Open the other end link of the chain and hang the fixture on the loop at
the ceiling .Close the link.
12. Feed the fixture wires through the loop (F) and nipple (C) and pull until
taut.
CONNECTING THE WIRES(Fig.2)
1. Take the black wire from the ceiling junction box and the smooth wire
leg from the fixture and twist bare ends together. Twist wire connector
onto end of wire until snug.
2. Repeat same process with white junction box wire and ribbed wire leg of
fixture wire. NOTE: Twist wires together in the same direction you twist
the wire connector onto wires.
3. If you junction box has a grounding wire (green or bare copper), attach
this wire and the bare copper wire from the fixture together as step 1.If
junction box has no ground wire, attach the bare copper fixture wire to
the green ground screw on the crossbar.
4. Tuck these wire connections neatly into the ceiling outlet box and then
raise the canopy (G) all the way to the ceiling. Raise the loop (H) and
thread onto ceiling loop protruding through canopy
5. Install the light bulbs in accordance with the fixture specifications.
NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE.
Fig.2
Fig.3
Fig.1
CIRCUIT BREAKER .
Download PDF