Minka Lavery | 4879-283 | Instructions / Assembly | Minka Lavery 4879-283 Instructions / Assembly

INSTALLATION INSTRUCTIONS
WARNING! SHUT
Item#4879-283 (New. 05/ 10/ 2014)
READ AND SAVE THESE INSTRUCTIONS
POWER OFF AT FUSE OR CIRCUIT BREAKER .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.2)
1.
2.
3.
4.
5.
6.
`
Fig.1
Shut off the power at the fuse box or circuit breaker. If
necessary, remove the existing fixture and its mounting
hardware from the ceiling.
Carefully remove the new fixture from the carton and check
that all parts are included as shown in the illustration.
Remove the screw (K), and remove the outer frame (N).
Insert glass (L) into the outer frame (N), and secure the glass
with clips (M).
Place the fixture body (J) into the outer frame (N), and secure
with screws (K). Secure fixture loop (I) to nipple on top of the
fixture body (J).
Install the light bulb (not included) in accordance with the
fixture’s specifications: DO NOT EXCEED THE MAXIMUM
WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!)
HANGING THE FIXTURE (Fig.1)
1.
2.
Thread nipple (C) into ceiling loop (F) until snug.
Thread the other end of nipple (C) with loop attached into
crossbar (D) until snug.
3. Place lock washer (B) and hex nut (A) over end of nipple
protruding through crossbar. Then thread hex nut (A) until
snug.
4. Take this crossbar assembly and mount to the ceiling outlet box
using outlet box screws (E) (Size: #8-32N*L0.5”). The side of
the crossbar marked “GND” must face out.
5. Using a pair of chain pliers, open one end link of the chain and
connect to the fixture loop (I). Then close the link.
6. Carefully lace the fixture wires through the chain.
7. By measuring, determine the correct number of links needed
for the desired hanging height. Using the chain pliers
disconnect and discard the excess chain.
8. Slip the lock collar (H) and canopy (G) over the chain, allowing
them to rest onto the fixture loop (I).
9. Open the other end link of the chain and attach it to the ceiling
loop (F). Then close the link.
10. Feed the fixture wires through the ceiling loop (F) and nipple
(C) and pull tight.
Set# A-016
- Crossbar
- Ground Screw
- Mounting Screw*2
Fig.2
CONNECTING THE WIRES (Fig.3)
At this point, connect the fixture wires as shown in
Fig.3, making sure that all wire connectors are secured.
If your outlet box has a ground wire (green or bare
copper), connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly to
the crossbar (D) using the green screw provided.
12. Tuck these wire connections neatly into the ceiling
outlet box and raise the canopy (G) to the ceiling. Then
raise the lock collar (H) and thread onto the ceiling loop
11.
(F) protruding through the canopy.
Your installation is now complete. Return power to the junction box
and test the fixture.
Note: Illustration (Fig.1) (Fig.2) on this manual is for
installation purposes only. It may or may not be identical
to the fixture purchased.
CHAIN HUNG FIXTURE INSTRUCTION
Notice: It is important to use proper chain pliers (not included) To
OPEN and CLOSE the chain included with this fixture. Do not open
them with other tools that may twist or stress the chain links. It is
important to use proper chain pliers like the ones shown in the
diagram.
Chain # HCH2072-283
Gauge D3.8mm
Fig.3
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
FIXTURE
WIRES
Bare
Copper
HOUSE (Ground) HOUSE
WIRES
WIRES
Green or
White
Bare Copper(Ground)
(Neutral)
CM
C
US
lntertek
Download PDF