Sea gull lighting | 3413-962 | Installation guide | Sea Gull Lighting 3413-962 Installation Guide

Installation And Safety Instructions
HC-315
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
030200
FOR YOUR SAFETY
GENERAL
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF; EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER SET AT OFF.
You don't need special tools to install this fixture. Be sure to follow
the steps in the order given. Under no circumstances should a
fixture be hung on house electrical wires, nor should a swag type
fixture be installed on a ceiling which contains a radiant type heating
system. Read instructions carefully. If you are unclear as to how
to proceed, consult a qualified electrician.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT TO OUTLET BOX
OR SUPPORTING SYSTEM ABLE TO SUPPORT
THE WEIGHT OF THE FIXTURE.
ASSEMBLY
*WIRE
CONNECTORS
Note: Fixture may be partly assembled.
*OUTLET BOX
*GROUND WIRE
STEP 2:
*OUTLET
BOX SCREWS
NIPPLE (C)
GROUND
WIRE (S)
SCREW COLLAR (D)
Be careful not to pinch the wires. Thread long center pipe (O) onto
coupling(M). Over long center pipe (O) slide, in the following order:
Column (H), bobeche(T), lock washer (P), and secure with the fixture
loop (I.)
STEP 3:
Thread short center pipe (U) to coupling (N). Over short center pipe
(U) slide, in the following order: neck(V), two piece ball(L) and
secure with round nut (W). Thread decorative loop (X) onto short
center pipe (U).
CANOPY (E)
CHAIN (G)
STEP 1:
Pull the wires from coupling (M), in the following order through: long
center pipe(O), column(H), lock washer(P), bobeche (T) and fixture
loop (I).
MOUNTING
BAR (A)
NUT (B)
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
*NOTE: If the following parts are not supplied, or they are
factory assembled; proceed to the next assembly step.
SCREW
COLLAR RING (F)
STEP 4:
Turn each arm (J) clockwise 1/4 turn to be upward or downward
(see the style on carton), if necessary. Do not turn past upward
position, this will cause arm to loosen.
FIXTURE
LOOP (I)
COLUMN (H)
BOBECHE (T)
GLASS
(IF APPLICABLE)
LOCK
WASHER (P)
GROUNDING AND MOUNTING BAR LOCK UP
*OUTLET BOX
*GROUND WIRE
LONG CENTER
PIPE (O)
*WIRE
CONNECTORS
CANDLE COVER (Q)
COUPLING (M)
COUPLING (N)
NECK (V)
SHORT
CENTER
PIPE (U)
ARM ASSEMBLY (J)
(ROTATE CLOCKWISE)
BODY ASSEMBLY (K)
*OUTLET BOX
SCREWS
BALL ASSEMBLY (L)
ROUND NUT (W)
DECORATIVE LOOP (X)
FIGURE 1
MOUNTING
BAR (A)
*NOT INCLUDED
GREEN
GROUNDING
SCREW (R)
FIGURE 2
NUT (B)
NIPPLE (C)
*NOT INCLUDED
INSTALLATION
HC-315
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are
exposed above nut (B). Thread nipple (C) into mounting bar (A) and
secure with nut (B). Attach screw collar (D) to nipple (C).
STEP 2:
Using 2 pairs of pliers, open one link of chain (G) and connect it to
the fixture loop (I) at the top of the fixture.
STEP 3:
Slide the screw collar ring (F) and canopy (E), in that order, over
chain (G). Open one link on the other end of the chain (G) and
attach it to the screw collar (D) which has been mounted to the
ceiling nipple (C). BE SURE TO CLOSE ALL CHAIN LINKS
COMPLETELY.
STEP 4:
Lace wires up through chain (G) and pass wires through holes in
screw collar (D). We recommend lacing wire up through every other
link of chain (G).
C. Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (R) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (S) from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (R) on the
mounting bar (A) if uninsulated wire is on the mounting bar (A),
connect the ground wire (S) from the fixture (if supplied) and the
outlet box to it using a small wire connector (not supplied).
NOTE: Underwriters Laboratories (U.L.) does not require all
fixtures to have ground wires. These fixtures still meet all UL
specifications. The listing mark of Underwriters on the product
identifies products manufactured under its listing and Follow-Up
Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 5:
Make sure no bare wires can be seen outside wire connectors.
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 1:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (E) against ceiling and screw the screw collar
ring (F) to the screw collar (D).
STEP 2:
Install candle covers (Q) (if applicable).
STEP 3:
Install lamps.
STEP 4:
Install glass in holder if applicable.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
*PARALLEL WIRE (ROUND & SMOOTH)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
*PARALLEL WIRE (SQUARE & RIDGED)
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
WHITE OR GREY WITH TRACER
WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT
TRACER
BROWN, GOLD OR BLACK WITH TRACER
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
Download PDF