Sea gull lighting | 4702-962 | Installation guide | Sea Gull Lighting 4702-962 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
ASSEMBLY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER OFF .
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
STEP 1:
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be
hung on house electrical wires, nor should a swag type fixture be
installed on a ceiling which contains a radiant type heating system.
Read instructions carefully. If you are unclear as to how to proceed,
consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
* OUTLET BOX
GROUND WIRE (D)
Peel protective coating off as follows: (if applicable). For easier
removal, peel coating off at an angle holding it close to the fixture.
Peel sides off before peeling the front faces.
NOTE: SOCKETS ARE FACTORY INSTALLED.
IF SOCKET IS NOT SECURE TO BACKPLATE, MAKE
SURE SOCKET TABS ARE SNAPPED ONTO
PRE-DRILLED HOLES IN BACKPLATE.
* WIRE
CONNECTOR
* OUTLET BOX
BACK PLATE (C)
GREEN GROUNDING
SCREW (A)
SOCKETS (J)
EXTRUDED HOLE (B)
DECORATIVE
FRONT (E)
WOOD
SCREWS (K)
GCO GROUND WIRE
(IF APPLICABLE)
FACE PLATE (F)
BACK PLATE
*ROMEX/BX
CONNECTOR
CUPS (I)
FIGURE 1
*NOT SUPPLIED
* WIRE
CONNECTOR
®
Installation And Safety
Instruction
FACE PLATE
FIGURE 2
*NOT SUPPLIED
HC-107
Fill In Item Number On Carton And
File This Sheet For Fixture Reference.
100101
ITEM#_______________
ALTERNATIVE MOUNTING METHOD (Fig. 2) HC-107
THIS FIXTURE CAN BE MOUNTED TO A WALL WITHOUT AN
OUTLET BOX, MAKING THE WIRING CONNECTION BETWEEN
THE FACEPLATE AND BACKPLATE.
1.
Remove knock-out from the backplate (if applicable), or remove
plastic bushing.
2.
Install Romex / Bx connector on the backplate.
3.
Feed house supply wires through Romex / Bx connector, and
secure.
4.
Make wiring connection as described in the steps that follow,
and tuck the wires between the faceplate and backplate.
INSTALLATION TO AN OUTLET BOX (Fig. 1)
STEP 1:
Punch out appropriate holes in backplate (C), if applicable, to
correspond with holes in outlet box.
STEP 2:
Push socket wires thru plastic bushing.
STEP 3:
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (A) is to
be inserted into the hole with two raised dimples provided on the
back plate (C). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green insulated wire) around the green grounding screw (A) on the back
plate (C).
NOTE: Underwriters Laboratories (U.L.) does not require all fixtures
to have ground wires. These fixtures still meet all U.L. specifications.
The listing mark of Underwriters on the product identifies products
manufactured under its listing and Follow-Up Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
Note: Fixtures that employ a grounded type receptacle are not
intended for connection to a two wire ungrounded source of supply.
STEP 1:
A. Take note of the color of the wire(S) on your fixture. Identify
which group your fixture wire(S) falls into and connect the wires
according to the directions below:
Tuck wires into outlet box. Attach backplate (C) to outlet box by
placing outlet box screws (not supplied) through punched out holes
in backplate (C).
If applicable: Wood screws (K) placed in outer holes will provide
additional support.
Note: Your fixture may be supplied with a faceplate (F), decorative
front (E), or both, depending on your model. Follow the directions
below according to the parts supplied with your fixture.
STEP 2:
Position faceplate (F) or decorative front (E) over sockets (J).
NOTE: If backplate (C) is supplied with mounting studs (H) position
faceplate over studs and secure in place with cap nuts (G).
STEP 3:
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
WHITE OR GREY WITH TRACER
WHITE OR GREY WITHOUT TRACER
For fixtures supplied with cups:
Push faceplate (F) or decorative front (E) to wall and secure by
pushing cups (I) onto sockets (J) in a clockwise motion. (If your
fixture is supplied with threaded sockets, thread rings (L) onto
sockets (J) in the same manner except screw them on.) NOTE: If
both decorative front (E) and faceplate (F) are supplied, place
faceplate (F) and wood (or mirror), in that order, over sockets (J)
before securing with cups or rings (L). NOTE: It may be necessary
to bend tabs in cup (I) for a tighter fit.
STEP 4:
BROWN, GOLD OR BLACK WITHOUT
TRACER
BROWN, GOLD OR BLACK WITH TRACER
Install lamps
CLEANING
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
B. Take your fixture wire(S) from group A and place evenly
against the black wire from the outlet box. Do Not twist wires
together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw
the connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps B and C, as above, and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from
the outlet box in the same manner.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
Download PDF