Sea gull lighting | 65145-814 | Installation guide | Sea Gull Lighting 65145-814 Installation Guide

Installation And Safety Instructions
HC-1003
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
FOR YOUR SAFETY
080406
ASSEMBLY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER OFF .
Carefully remove the fixture from the carton and check that all parts are included,
as shown in Figure 1 & 2. Be careful not to misplace any of the screws or parts
which are needed to install this fixture.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the steps in the
order given. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.
*OUTLET BOX
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT TO OUTLET BOX
OR SUPPORTING SYSTEM ABLE TO SUPPORT THE
WEIGHT OF THE FIXTURE.
*WIRE CONNECTORS
*GROUND WIRE
GROUNDING AND MOUNTING BAR LOCK UP
MOUNTING BAR (A)
*OUTLET BOX
*OUTLET BOX
*GROUND WIRE
SCREWS
GROUND WIRE (F)
*WIRE
CONNECTORS
SCREW COLLAR (E)
CANOPY (H)
SCREW COLLAR
RING (G)
CHAIN (S)
MOUNTING
BAR (A)
*OUTLET BOX
SCREWS
GREEN
GROUNDING
SCREW (D)
FIGURE 2
*NOT INCLUDED
LOOP (I)
GLASS (J)
THREADED GLASS
RETAINER RING (L)
*NOT SUPPLIED
FIGURE 1
NUT (B)
NIPPLE (C)
INSTALLATION
HC-1003
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not supplied).
Thread nut (B) on nipple (C) so that 3 threads are exposed above nut (B). Thread
nipple (C) into mounting bar (A) and secure with nut (B). Attach screw collar (E)
to nipple (C).
STEP 2:
Using 2 pairs of pliers, open one link of chain (S) and connect it to the fixture loop
(I) at the top of the fixture.
STEP 3:
Slide the screw collar ring (G) and canopy (H), in that order, over chain (S).
Open one link on the other end of the chain (S) and attach it to the screw collar (E) which has been mounted to the ceiling nipple (C).
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to be
inserted into the hole with two raised dimples provided on the mounting bar (A).
Wrap the ground wire (F) from the fixture (if supplied) and the ground wire from the
outlet box (bare metal or green
insulated wire) around the green grounding screw (D) on the
mounting bar (A) if uninsulated wire is on the mounting bar (A),
connect the ground wire (F) from the fixture (if supplied) and the outlet box to it
using a small wire connector (not supplied).
NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to have ground
wires. These fixtures still meet all U.L. specifications. The listing mark of Underwriters on the product identifies products manufactured under its listing and Follow-Up
Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
STEP 4:
Lace wires up through chain (S) and pass wires through holes in screw collar (E).
We recommend lacing wire up through every other link of chain (S).
STEP 5:
A. Take note of the color of the wire(s) on your fixture. Identify which group your
fixture wire(s) falls into and connect the wires according to the directions below:
After wires are connected, tuck them carefully inside outlet box and then raise the
canopy (H) against ceiling and screw the screw collar ring (G) to the screw collar
(E).
STEP 2:
Raise glass (J) in socket assembly and secure in place by screwing retaining ring
(L) onto socket.
STEP 3:
Install lamp.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use
abrasive materials such as scouring pads or powders, steel wool or abrasive
paper.
ORDERING PARTS
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
WHITE OR GREY WITH TRACER
WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT TRACER
BROWN, GOLD OR BLACK WITH TRACER
*Note: When parallel wire is used, the tracer wire is square shaped or ridged and less
tracer wire is round in shape or smooth. (Seen best when viewed from wire end.)
To separate wires, grasp the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against the black wire
from the outlet box. DO NOT twist wires together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw the connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull the connector off,
carefully re-do steps B and C, as above and check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the outlet box in the
same manner.
Keep this sheet for future reference, and in case you need to order replacement
parts. All parts for this fixture can be ordered from place of purchase. Be sure to
use exact wording from illustration when ordering parts.
Download PDF