Sea gull lighting | 61660-839 | Installation guide | Sea Gull Lighting 61660-839 Installation Guide

Installation And Safety Instructions
HC-1433
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
CLEANING
112008
FOR STEM MOUNT
*OUTLET BOX
*WIRE
CONNECTORS
MOUNTING
BAR (A)
GREEN GROUNDING
SCREW (D)
NUT (C)
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
NIPPLE (I)
CANOPY (G)
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
SCREW COLLAR (B)
SCREW COLLAR
RING (K)
COUPLING (J)
ROD ASSEMBLY (E)
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
STEP 1:
Feed the fixture wire through the fixture loop (F) and thread fixture
loop (F) to top of fixture.
INSTALLATION – ROD ASSEMBLY
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
Secure mounting bar (A) to outlet box using outlet box screws (not
supplied). Thread nut (C) onto nipple (I) so five threads are exposed.
Thread nipple (I) to mounting bar (A) and secure by threading nut (C)
to mounting bar (A). Thread screw collar (B) to nipple (I).
NOTE: THIS FIXTURE
CAN BE HUNG USING
1, 2, OR 3 RODS.
SELECT THE NUMBER
OF RODS DESIRED.
FIXTURE LOOP (F)
SOCKET
ASSEMBLY (U)
STEP 2:
Assemble rod assembly (E) by threading desired amount of rods
together.
SHADE (R)
STEP 3:
Feed the fixture wire from the socket assembly (U), through: the rod
assembly (E) and thread rod assembly (E) into socket assembly (U).
STEP 4:
RETAINING RING (T)
Slide screw collar ring (K) and canopy (G) (in that order) to top of
socket assembly (U). Be sure not to damage the fixture wire. Thread
rod assembly (E) to nipple of the coupling (J).
FIGURE 1
*NOT INCLUDED
INSTALLATION – CHAIN
HC-1433
FOR CHAIN MOUNT
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
Secure mounting bar (A) to outlet box using outlet box screws (not
supplied). Thread nut (C) onto nipple (I) so five threads are exposed.
Thread nipple (I) to mounting bar (A) and secure by threading nut (C)
to mounting bar (A). Thread screw collar (B) to nipple (I).
*OUTLET BOX
STEP 2:
Using 2 pairs of pliers, open one link of chain (M) and attach to
fixture loop at top of fixture. Run wire through every other loop of
chain.
STEP 3:
Slide screw collar ring (K) and canopy (G) over chain to fixture loop
(F).
*WIRE
CONNECTORS
MOUNTING
BAR (A)
GREEN GROUNDING
SCREW (D)
NUT (C)
STEP 4:
Open other length of chain and attach to the screw collar (B). Close
all lengths of chain to secure.
NIPPLE (I)
CANOPY (G)
WIRING
STEP 5:
SCREW COLLAR (B)
SCREW COLLAR
RING (K)
COUPLING (J)
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
CHAIN (M)
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (D) on the
mounting bar (A). If uninsulated wire is on the mounting bar (A),
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
ROD ASSEMBLY (E)
NOTE: THIS FIXTURE
CAN BE HUNG USING
1, 2, OR 3 RODS.
SELECT THE NUMBER
OF RODS DESIRED.
SOCKET
ASSEMBLY (U)
STEP 7:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (G) against the ceiling. Secure by threading
screw collar ring (K) onto screw collar (B).
SHADE (R)
STEP 8:
Place shade (R) securely in socket assembly (U). Secure by
threading retaining ring (T) onto socket.
STEP 9:
Install lamp.
RETAINING RING (T)
FIGURE 2
*NOT INCLUDED
Download PDF