MH20330AS Installation, Use and Care Guide

MH20330AS Installation, Use and Care Guide
MODEL #.
MH20330AS
Installation, Use and Care Guide
READ AND SAVE THESE INSTRUCTIONS
2015.JUL
INSTALLATION
Ducting Calculation Sheet .......................................
Mounting Height & Clearance................................
Ducting Options ...........................................................
6SHFL¿FDWLRQV ...............................................................
Preparing Electrical ....................................................
Preparing Electrical and Ducting ..........................
Converting to Air Recirculating Mode .................
Mounting the Range Hood .............................
5
6
7
8
9
10
11-12
13
FEATURES & CONTROLS
Rocker Controls ........................................................... 14
MAINTENANCE
Cleaning and Filter Removal.................................. 15
Lights ................................................................................ 16
TROUBLESHOOTING................................................................ 17
WIRING DIAGRAMS ................................................................... 18
LIST OF PARTS AND ACCESSORIES .............................. 19
WARRANTY .................................................................................... 20
1
Table of Contents
SAFETY NOTICE ................................................................. 2-3
LIST OF MATERIALS....................................................... 4
Important Safety Notice
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.
WARNING
TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.
b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service
panel.
CAUTION
For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning
agents or detergents. Suitable for use in household cooking area.
WARNING
TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:
a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly
on low or medium settings.
E $OZD\VWXUQKRRG21ZKHQFRRNLQJDWKLJKKHDWRUZKHQÀDPLQJIRRG
F &OHDQYHQWLODWLQJIDQVIUHTXHQWO\*UHDVHVKRXOGQRWEHDOORZHGWRDFFXPXODWHRQIDQRU¿OWHU
d. Use proper pan size. Always use cookware appropriate for the size of the surface element.
H .HHSIDQ¿OWHUVDQGJUHDVHODGHQVXUIDFHVFOHDQ
f. Use high setting on hood only when necessary.
g. Don’t leave hood unattended when cooking.
h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:
D 6027+(5)/$0(6ZLWKDFORVH¿WWLQJOLGFRRNLHVKHHWRUPHWDOWUD\WKHQWXUQRIIWKHEXUQHU%(&$5()8/7235(9(17%8516
,IWKHÀDPHVGRQRWJRRXWLPPHGLDWHO\(9$&8$7($1'&$//7+(),5('(3$570(17
b. NEVER PICK UP A FLAMING PAN – You may be burned.
c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
d. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
7KH¿UHLVVPDOODQGFRQWDLQHGLQWKHDUHDZKHUHLWVWDUWHG
7KH¿UHGHSDUWPHQWLVEHLQJFDOOHG
<RXFDQ¿JKWWKH¿UHZLWK\RXUEDFNWRDQH[LW
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
D ,QVWDOODWLRQZRUNDQGHOHFWULFDOZLULQJPXVWEHGRQHE\TXDOL¿HGSHUVRQVLQDFFRUGDQFHZLWKDOODSSOLFDEOHFRGHVDQGVWDQGDUGV
,QFOXGLQJ¿UHUDWHGFRQVWUXFWLRQ
E 6XI¿FLHQWDLULVQHHGHGIRUSRZHUFRPEXVWLRQDQGH[KDXVWLQJRIJDVHVWKURXJKWKHÀXHFKLPQH\RIIXHOEXUQLQJHTXLSPHQWWRSUHYHQW
back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National
)LUH3URWHFWLRQ$VVRFLDWLRQ1)3$DQGWKH$PHULFDQ6RFLHW\IRU+HDWLQJ5HIULJHUDWLRQDQG$LU&RQGLWLRQLQJ(QJLQHHUV$6+5$(DQG
the local code authorities.
c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
d. Ducted fans must always vent to the outdoors.
e. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFI
*URXQG)DXOW,QWHUUXSWHUSURWHFWHGEUDQFKFLUFXLW
g. NEVER place a switch where it can be reached from a tub or shower.
h. Make sure the power is off before installing, wiring or maintenancing.
2
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
NOT FOR USE OVER AN OUTDOOR GRILL.
CAUTION
7RUHGXFHULVNRI¿UHDQGWRSURSHUO\H[KDXVWDLURXWVLGH'RQRWYHQWH[KDXVWDLULQWRVSDFHVZLWKLQZDOOVFHLOLQJV
attics, crawl spaces or garages.
OPERATION
$OZD\VOHDYHVDIHW\JULOOHVDQG¿OWHUVLQSODFH:LWKRXWWKHVHFRPSRQHQWVRSHUDWLQJEORZHUVFRXOGFDWFKRQWRKDLU¿QJHUV
and loose clothing.
The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,
maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to
negligence and the warranty of the unit automatically expires due to improper maintenance.
ELECTRICAL REQUIREMENTS
Important:
Observe all governing codes and ordinances.
It is the customer’s responsibility:
7RFRQWDFWDTXDOL¿HGHOHFWULFDOLQVWDOOHU
- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70
latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and
all local codes and ordinances.
,IFRGHVSHUPLWDQGDVHSDUDWHJURXQGZLUHLVXVHGLWLVUHFRPPHQGHGWKDWDTXDOL¿HGHOHFWULFLDQGHWHUPLQHWKDWWKH
ground path is adequate.
Do not ground to a gas pipe.
&KHFNZLWKDTXDOL¿HGHOHFWULFLDQLI\RXDUHQRWVXUHWKHUDQJHKRRGLVSURSHUO\JURXQGHG
Do not have a fuse in the neutral or ground circuit.
*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575
This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit
protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to
Electrical Diagram on product.
$FDEOHORFNLQJFRQQHFWRUQRWVXSSOLHGPLJKWDOVREHUHTXLUHGE\ORFDOFRGHV&KHFNZLWKORFDOUHTXLUHPHQWVSXUFKDVH
and install appropriate connector if necessary.
MH20330AS - 142 Watts, 1.3 Amps
3
Important Safety Notice
WARNING
List of Materials
MODELS: MH20330AS
PARTS SUPPLIED
1 - Hood
2 - Aluminum Mesh Filters
+DORJHQ/LJKW%XOEV*8:
1 - 6” Round starting collar
1 - 3-1/4”x10” Rectangular starting collar with damper
1 - Hardware package
HARDWARE PACKAGE CONTENTS
M6 x 2” (4)
M6 x 1-1/2” (4)
M6 x 1” (4)
M3.5 x 12 (10)
Light Bulb Removal
Suction Cup (1)
Wood Screw Washers (4)
Wire Caps (3)
PARTS NOT SUPPLIED
- Ducting, conduit and all installation tools
&DEOHFRQQHFWRUif required by local codes
- Recirculating kit accessory - RHRK203S
4
Duct pieces
Total
1 Ft.
x(
) =
Ft.
6”, 7”, 8”, 10” 1 Ft.
Round,
straight
x(
) =
Ft.
3-1/ 4” x 10”
Rect. 90 0
elbow
15 Ft.
x(
) =
Ft.
3-1/ 4” x 10”
Rect. 45 0
elbow
9 Ft.
x(
) =
3-1/ 4” x 10”
Rect.,
straight
Equivalent number
length x used
=
Total
3-1/ 4” x 10” 5 Ft.
Rect. to
6” round
transition
x(
) =
Ft.
3-1/ 4” x 10” 20 Ft.
Rect. to
6” round
transition
90 0 elbow
x(
) =
Ft.
6” round to
1 Ft.
3-1/ 4” x 10”
rect.
transition
x(
) =
Ft.
Ft.
x(
) =
Ft.
24 Ft.
x(
) =
Ft.
6” round to
16 Ft.
3-1/ 4” x 10”
rect.
transition
90 0 elbow
) =
Ft.
x(
) =
Ft.
7” round to
8 Ft.
3 1/ 4” x 10”
rect.
transition
x(
7” to 6” or
25 Ft.
8” to 7” Round
tapered
reducer
x(
) =
Ft.
15 Ft.
x(
7” round to
23 Ft.
3-1/ 4” x 10”
rect.
transition
90 0 elbow
x(
) =
Ft.
Ft.
3-1/ 4” x 10” 30 Ft.
Rect.
wall cap
with damper
x(
) =
Ft.
Ft.
6”, 7”, 8”, 10” 30 Ft.
Round, wall
cap with
damper
6”, 7”, 8”, 10” 30 Ft.
Round
roof cap
x(
) =
Ft.
Subtotal column 2 =
Ft.
Subtotal column 1 =
Ft.
Total ductwork
Ft.
3-1/ 4” x 10”
Rect. 90 0
flat elbow
6”, 7“, 8”
Round
in-line
damper
6”, 7”, 8”, 10” 15 Ft.
Round,
90 0 elbow
x(
6”, 7”, 8”, 10” 9 Ft.
Round,
45 0 elbow
x(
) =
) =
) =
Subtotal column 1 =
Ft.
Ft.
Maximum Duct Length: For satisfactory air movement,
the total duct length should not exceed 100 equivalent feet.
5
=
Installation – Ducting Calculation Sheet
Equivalent number
length x used
=
Duct pieces
Installation – Mounting Height & Clearance
Minimum mount height between range top to hood
bottom should be no less than 24”.
Maximum mount height should be no higher than
32”.
It is important to install the hood at the proper
mounting height. Hoods mounted too low could
UHVXOWLQKHDWGDPDJHDQG¿UHKD]DUGZKLOHKRRGV
mounted too high will be hard to reach and will
ORVHLWVSHUIRUPDQFHDQGHI¿FLHQF\
5-1/2”
If available, also refer range manufacturer’s height
clearance requirements and recommended hood
mounting height above range.
Min 24” - Max 32"
96"
Vertical Ducting:
6” Round or 3-1/4”x10” Rect. minimum
36"
Horizontal Ducting:
3-1/4”x10” Rect. minimum
DUCTING
A minimum 6” round or 3-1/4” x 10” rectangular
GXFWPXVWEHXVHGWRPDLQWDLQPD[LPXPDLUÀRZ
HI¿FLHQF\
Always use rigid type metal ducts only. Flexible
GXFWVFRXOGUHVWULFWDLUÀRZE\XSWR
$OVRXVHFDOFXODWLRQRQSDJHWRFRPSXWHWRWDO
available duct run when using elbows, transitions
and caps.
ALWAYS, when possible, reduce the number or
transitions and turns. If long duct run is required,
increase duct size.
If turns or transitions are required; install as far
away from hood duct output and as far apart,
between the two as possible.
6
DAMAGE-SHIPMENT / INSTALLATION:
‡ 3OHDVHIXOO\LQVSHFWXQLWIRUGDPDJHEHIRUH
installation.
‡ ,IWKHXQLWLVGDPDJHGLQVKLSPHQWUHWXUQWKH
unit to the store in which it was bought for
repair or replacement.
‡ ,IWKHXQLWLVGDPDJHGE\WKHFXVWRPHUUHSDLU
or replacement is the responsibility of the
customer.
‡ ,IWKHXQLWLVGDPDJHGE\WKHLQVWDOOHULIRWKHU
WKDQWKHFXVWRPHUUHSDLURIUHSODFHPHQWPXVW
be made by arrangement between customer
and installer.
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.
All exhaust must be ducted to the outside, unless using the recirculating option.
Use single wall rigid metal ductwork only.
)DVWHQDOOFRQQHFWLRQVZLWKVKHHWPHWDOVFUHZVDQGWDSHDOOMRLQWVZLWKFHUWL¿HG6LOYHU7DSHRU'XFW7DSH
Some Ducting Options
Roof Pitch w/
Flashing & Cap
Side wall cap
w/ gravity damper
6” Round or
3-1/4”x10” Rect.
vertical ducting
3-1/4”x10” Rect.
horizontal ducting
Air Recirculating
7
Installation – Ducting Options
WARNING FIRE HAZARD
TOP
6” Round Ducting
12 3/16”
elec.
k/o
5 7/8”
2”
2 3/4”
3/4”
4 3/16”
10”
C/L of
6” duct
12 3/16”
3 1/4”
10”
8 5/8”
1 7/16”
27 13/16”
2 3/4”
3/4”
elec.
k/o
5 7/8”
6”
2”
Air Recirculating Louver Plate
SIDE
11/16”
10”
3 1/4”
7/8”
BACK
Air Recirculating Louver Plate
20 3/16”
14 3/8”
5 7/8”
3/4”
2”
2.5
2 1/
29 7/8”
21
.6
3”
elec.
k/o
19 3/8”
8
5 1/2”
1 7/16”
27 13/16”
8 5/8”
Installation – 6SHFL¿FDWLRQV
TOP
3 1/4”x10” Rect. Ducting
WARNING
$OO(OHFWULFDOZRUNPXVWE\SHUIRUPHGE\TXDOL¿HGHOHFWULFLDQRUSHUVRQZLWKVLPLODUWHFKQLFDONQRZ
how and background.
For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use
extension cord or adapter plug with this appliance.
Follow national electrical codes or prevailing local codes and ordinances.
Electrical Supply:
This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly grounded
branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire w/
ground. Please also refer Electrical Diagram labeled on product.
MH203 - 142 Watts @ 1.3 Amps
Cable Lock:
$FDEOHORFNLQJFRQQHFWRUQRWVXSSOLHGPLJKWDOVREHUHTXLUHGE\ORFDOFRGHV&KHFNZLWKORFDOUHTXLUHPHQWV
and codes, purchase and install appropriate connector if necessary.
Cable Lock
9
Installation – Preparing Electrical
ELECTRICAL
Installation – Preparing Electrical and Ducting
1. Remove filters
2. Remove cover from junction box to
gain access to electrical wiring.
3. If using a cable lock, pry open the
desired electrical knockout either on
top or back of hood. Feed the wires
through the cable lock. Some local
codes require the use of a cable lock,
check your local codes.
4. If using hood in air recirculating
mode skip steps 4 and 5.
5. Remove starting collar from inside
hood body and secure 3-1/4” x 10”
rect. starting collar to the top or rear
duct opening using (10) M3.5x12
screws.
5. Remove starting collar from inside
hood body and secure 6” round starting collar to the top duct opening using
(10) M3.5x12 screws.
10
Pry open desired ducting knock-out
either on top or back of hood.
1. Secure each of the (2) spring clips to the
safety grille body (A). Do this by inserting
the screw through the spring and into the
clip. Secure each clip to the safety grille
body by using a philips head screwdriver.
An air recirculating kit (optional) must be
purchased before using hood in recirculating mode.
Recirculating kit - RHRK203S
5HSODFHPHQW¿OWHU5+&)
2. Insert charcoal filter into charcoal filter
holder (B) and place it over the safety grille
body (A)
3. Secure charcoal filter holder to safety
grill body by lifting up on spring clips and
twisting. The clip should cover the lip of the
charcoal filter holder securely.
Recirculating preparation
continued on next page
4. Remove each screw from recirculating
top plate. Plate is located on top of hood
towards the front.
11
Installation – Converting to Air Recirculating Mode
NOTE: Skip the recirculating preparation pages if you are ducting the air out of your home.
Installation – Converting to Air Recirculating Mode
NOTE: Skip this page if you are ducting the air out of your home.
5. Remove each of the 5 screws holding
the (2) interior recirculating panels.
7. Place louvered recirculating plate over
top opening and secure using the screws
previously removed.
12
6. Remove (2) interior recirculating panels.
electrical
6HOHFWSUHIHUUHGGXFWORFDWLRQYHUWLFDORUKRUL]RQWDOLI
ducting air out of kitchen. Refer to page 10 for details.
%HJLQLQVWDOODWLRQE\UHPRYLQJWKH¿OWHUVLILQVWDOOHG
Duct
opening
cutout
3. Reinforce cabinet with 1”x2” wood strips if additional
strengthening is required or if cabinets are
framed.
4. Cut out the required openings for duct and electrical
access by following the dimensions on page 8;
make sure the duct opening is large enough to apply
GXFWWDSH5HIHUWR)LJIRUPLQLPXPGXFWFXWRXW
dimensions
duct/silver
tape
5. Position range hood in the desired mounting location
DQGIDVWHQKRRGRQWRFDELQHWZLWK0ZRRGVFUHZV
provided.
Add 1x2
wood strips
6. Install electrical.
7. Install duct work and duct tape.
5HLQVWDOO¿OWHUV
9. Power up hood and check for leaks around duct tape.
6KRZQDVYHUWLFDO´[´GXFWLQJ
Fig 1
Back of
Cabinet
C/L
Front of
Cabinet
Minimum
duct cut out
W
”
D
2
*1/
Minimum duct cut out dimensions
6” Round Vertical Ducting 3 1/4” x 10” Rect. Ducting
Width : 11”
Width : 11”
Depth : 8”
Depth : 4 1/2”
* Depth dimensions start 1/2” from wall
Fig 2
13
Installation – Mounting the Range Hood
For Mounting Under a Kitchen Cabinet (Fig 1)
Features & Controls – Rocker Controls
Blower On/Off/Speed Selection
Lights Off/Dim/Bright
0
0
This switch turns the blower on and off and controls the speed selection.
is off, is low speed and is high speed .
Lights Off/Dim/Bright
is off, is dim and
is bright.
14
Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent,
or steel wool/scouring pads which will scratch and damage surface. Do not use products containing chlorine
bleach or orange cleaners.
For heavier soil use liquid degreaser.
After cleaning, you may use non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless
OXVWHUDQGJUDLQ$OZD\VVFUXEOLJKWO\XVLQJDPLFUR¿EHURUFOHDQFRWWRQFORWKDQGZLWKJUDLQ
Aluminum Mesh Filters
7KHDOXPLQXPPHVK¿OWHUVDUHLQWHQGHGWRWUDSUHVLGXHDQGJUHDVHIURPFRRNLQJ$OWKRXJKWKH¿OWHUVVKRXOG
never need replacing, they are required to be cleaned every 30 days or more often depending on cooking
habits.
)LOWHUVPD\EHSODFHGLQGLVKZDVKHUDWORZKHDWRUVRDNHGLQKRWVRDS\ZDWHU'U\¿OWHUVDQGUHLQVWDOOEHIRUH
using hood.
Removing Aluminum Mesh Filters (Fig 3)
3XVKLQRQ¿OWHUKDQGOHV
3LYRWIURQWRI¿OWHUGRZQZDUG
5HPRYH¿OWHUE\SXOOLQJDZD\IURPKRRG
Fig 3
15
Maintenance – Cleaning and Filter Removal
SURFACE MAINTENANCE:
Maintenance – Lights
REPLACING LIGHT BULBS
CAUTION: Light bulb becomes extremely hot when turned on.
DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns.
Make sure all power is turned off and bulbs are not hot.
Remove by turning bulb counter clockwise. Note: Bulb does not unscrew; it turns 60 degrees, stops and falls
out.
,IEXOEVDUHGLI¿FXOWWRWXUQGXHWRSURORQJHGXVH¿UPO\DWWDFKWKHSURYLGHGJODVVVXFWLRQFXSRUXVHDUXEEHU
latex glove and turn counter clockwise.
5HSODFHPHQWEXOEVDUHDYDLODEOHDWVSHFLDOW\OLJKWLQJVWRUHV3XUFKDVHW\SH05*8:KDORJHQ
For part numbers please turn to page 19 of the manual.
Bottom hood view
16
Issue
Cause
What to do
After installation,
the unit doesn’t
work.
1. The power source is not turned ON.
1. Make sure the circuit breaker and the unit’s
power is ON.
2. The power line and the cable locking connector
is not connecting properly.
2. Check the power connection with the unit is
connected properly.
3. The switch wirings are disconnected.
3. Make sure the wirings between the switch are
connected properly.
4. The switch board or control board is defective.
4. Change the switch board or control board.
1. The motor is defective, possible seized.
1. Change the motor.
2. The thermally protected system detects if the
motor is too hot to operate and shuts the motor
down.
2. The motor will function properly after the
thermally protected system cool down.
3. Damaged capacitor.
3. Change the capacitor.
4. The motor wire is not connected.
4. Make sure the motor wire is plugged into the
molex connector.
1. The motor is not secure in place.
1. Tighten the motor in place.
2. Damaged blower wheel.
2. Change the blower.
3. The hood is not secured in place.
3. Check the installation of the hood.
1. Defective bulb.
1. Change the bulb.
2. The light bulb is loose.
2. Tighten the light bulb.
3. The wires on the switch are loose.
3. Make sure the wires on switch are connected
properly.
1. The hood might be hanging to high from the
cook top.
1. Adjust the distance between the cook top and
the bottom of the hood within 24” and 32”
range.
2. The wind from the opened windows or opened
doors in the surrounding area are affecting the
ventilation of the hood.
2. Close all the windows and doors to eliminate
WKHRXWVLGHZLQGÀRZ
3. Blockage in the duct opening or duct work.
3. Remove all the blocking from the duct work or
duct opening.
4. The direction of duct opening is against the wind.
4. Adjust the duct opening direction.
5. Using the wrong size of ducting.
5. Change the ducting to correct size.
0HWDO¿OWHULVORRVH
1. Make sure spring on handle still works.
2. Handle does not freely move.
5HSODFHPHWDO¿OWHU
Light works,
but motor is not
turning.
The unit is
vibrating.
The motor is
working, but the
lights are not.
The hood is
not venting out
properly.
0HWDO¿OWHULV
vibrating.
17
Troubleshooting
TROUBLESHOOTING PROCEDURES FOR MH203
Wiring Diagrams
MH20330AS
18
PART #
Replacement Parts
/LJKW%XOE05*8:HDFK
$OXPLQXP0HK)LOWHUHDFK
=%
Optional Accessories
Recirculating Kit
RHRK203S
5HSODFHPHQW&KDUFRDO)LOWHUVSN 5+&)
Order replacement parts from us by calling 1.888.750.1698
19
List of Parts and Accessories
DESCRIPTION
Warranty
STAPLE YOUR RECEIPT HERE
Proof of the original purchase
date is needed to obtain
service under warranty
Limited Warranty
TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call:
1-888-750-1698
Venting Services (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as
“you” or “your”) of range hoods (the “Products”) that such Products will be free from defects in materials or workmanship
as follows:
One Year Limited Warranty for Parts: For one year from the date of your original purchase of the Products, we will
provide, free of charge, Products or parts to replace those that failed due to manufacturing defects. We may choose, in
our sole discretion, to repair or replace parts before we elect to replace the Products.
One Year Limited Warranty for Labor: For one year from the date of your original purchase of the Products, we will
provide, free of charge, the labor cost associated with repairing the Products or parts to replace those that failed due to
manufacturing defects. After the first year from the date of your original purchase, you are responsible for all labor costs
associated with this warranty.
Warranty Exclusions: This warranty covers only repair or replacement, at our option, of defective Products or parts
and does not cover any other costs related to the Products including but not limited to: (a) normal maintenance and
service required for the Products and consumable parts such as light bulbs, metal and carbon filters and fuses; (b) any
Products or parts which have been subject to freight damage, misuse, negligence, accident, faulty installation or installation contrary to recommended installation instructions, improper maintenance or repair (other than by us); (c) commercial use of the Products or use otherwise inconsistent with its intended purpose; (d) natural wear of the finish of the Products or wear caused by improper maintenance, use of corrosive and abrasive cleaning products, pads, and oven cleaner
products; (e) chips, dents or cracks caused by abuse or misuse of the Products; (f) service trips to your home to teach
you how to use the Products; or (g) damage to the Products caused by accident, fire, floods or act of God. If you are
outside our service area, additional charges may apply for shipping costs for warranty repair at our designated service
locations and for the travel cost to have a service technician come to your home to repair, remove or reinstall the Products. After the first year from the date of your original purchase, you are also responsible for all labor costs associated
with this warranty.
Limitations of Warranty. OUR OBLIGATION TO REPAIR OR REPLACE, AT OUR OPTION, SHALL BE YOUR SOLE
AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. WE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF
THE PRODUCTS. THE EXPRESS WARRANTIES IN THE PRECEDING SECTION ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER EXPRESS WARRANTIES. WE HEREBY DISCLAIM AND EXCLUDE ALL OTHER EXPRESS WARRANTIES FOR THE PRODUCTS, AND DISCLAIM AND EXCLUDE ALL WARRANTIES IMPLIED BY LAW, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states or provinces do not
allow limitations on the duration of an implied warranty or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. To the extent that applicable law prohibits the exclusion of implied warranties, the duration of any applicable implied warranty is limited to the same one-year period
described above. Any oral or written description of the Products is for the sole purpose of identifying the Products and
shall not be construed as an express warranty. Prior to using, implementing or permitting use of the Products, you shall
determine the suitability of the Products for the intended use, and you shall assume all risk and liability whatsoever in
connection with such determination. We reserve the right to use functionally equivalent refurbished or reconditioned
parts or Products as warranty replacements or as part of warranty service. This warranty is not transferable from the
original purchaser and applies in the United States and Canada.
To Obtain Service Under Limited Warranty: To qualify for warranty service, you must: (a) notify us at the address or
telephone number stated below within 60 days of the discovery of the defect; (b) give the model number and part identification number and serial number; and (c) describe the nature of any defect in the Product or part. At the time of the
request for warranty service, you must present evidence of your proof of purchase and proof of the original purchase
date. If we determine that the warranty exclusions listed above apply or if you fail to provide the necessary documentation to obtain service, you will be responsible for all shipping, travel, labor and other costs related to the services.
Venting Services PO Box 6188 Oakland, CA 94603 | 1-888-750-1698 | vsupport@ventingservices.com
MAY10.0101
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising