Sea gull lighting | 65225-02 | Installation guide | Sea Gull Lighting 65225-02 Installation Guide

Installation And Safety Instructions
HC-1321
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
BEFORE YOU BEGIN
Be sure the electricity to the system you are working on is turned off;
either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing and
create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don't need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
To reduce the risk of fire, electric shock, or personal injury, mount to
outlet box or supporting system able to support the weight of the fixture
Save these instructions.
*OUTLET BOX
*HOUSE
GROUND WIRE
031108
*WIRE
CONNECTORS
Carefully remove the fixture from the carton and check that all
parts are included, as shown in Figure 1 & 2. Be careful not to
misplace any of the screws or parts which are needed to install
this fixture.
STEP 1:
Attach fixture loop (K) to top of fixture (if applicable).
GROUNDING AND MOUNTING
BAR LOCK UP
*OUTLET BOX
MOUNTING BAR
(A)
*HOUSE
GROUND WIRE
*OUTLET BOX
SCREWS
*WIRE
CONNECTORS
NUT (B)
NIPPLE (C)
GROUND
WIRE (F)
MOUNTING
BAR (A)
COLLAR (E)
*OUTLET
BOX
SCREWS
CANOPY (H)
GREEN
GROUNDING
SCREW (D)
COLLAR RING (I)
NUT (B)
NIPPLE (C)
FIGURE 2
CHAIN (J)
FIXTURE
LOOP (K)
SHADE (G)
GLASS
RETAINING
RING (L)
FIGURE 1
SUPPORT
WASHER (Z)
*NOT SUPPLIED
*NOT INCLUDED
INSTALLATION
HC-1321
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are exposed
above nut (B). Thread nipple (C) into mounting bar (A) and secure
with nut (B). Attach collar (E) to nipple (C).
STEP 5:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (F) from the fixture and the
ground wire from the outlet box (bare metal or green insulated
wire) around the green grounding screw (D) on the mounting bar
(A) if uninsulated wire is on the mounting bar (A), connect the
ground wire (F) from the fixture and the outlet box to it using a
small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2:
Using 2 pairs of pliers, open one link of chain (J) and connect it to
the fixture loop (K) at the top of the fixture.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 3:
Slide the collar ring (I) and canopy (H), in that order, over chain
(J). Open one link on the other end of the chain (J) and attach it
to the collar (E) which has been mounted to the nipple (C).
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
STEP 4:
STEP 1:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (H) against ceiling and thread the collar ring (I)
to the collar (E).
STEP 2:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according to
the directions below:
Install lamp.
STEP 3:
Raise shade (G) over socket and secure by threading support
washer (Z) and glass retaining ring (L) onto socket.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
*PARALLEL WIRE (ROUND & SMOOTH)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
Download PDF